Search Documents

By C. A. Biley

"A dedicated iron removal stage was installed at Anglo American Platinum’s Rustenburg Base Metals Refiners (RBMR) during an expansion project which began execution in 2010. The Pressure Iron Removal (PIR) process aims to precipitate iron from a nickel leach solution under medium temperature (145 °C) oxidative conditions using caustic for neutralisation. Since commissioning, the process has been robust in removing iron from the refinery but has shown significant variability in the residues produced. These residues, which are typically comprised of ferrihydrite, hematite or natrojarosite, have varying iron contents and different physical properties which have implications for their filtration and ultimate removal from the refinery. Since over 95% of nickel plated at RBMR passes through the PIR section, volumetric constraints caused by poor filtration performance directly influence nickel production and stabilisation of this process remains central to the continued ramp-up of the refinery to full nameplate capacity. This paper details the development of the PIR process and the journey from concept to implementation. Recent laboratory and plant scale tests have highlighted the importance of the initial phase formed in the autoclave for the ultimate residue requiring filtration and how the feed acid concentration is a critical control parameter. On this basis, a new caustic dosing philosophy was implemented which improved pH control in the autoclave. Further optimisation of the PIR process is on-going.INTRODUCTIONIn 2010, an expansion of Rustenburg Base Metal Refiners (RBMR) to increase nickel production from 21 to 33 ktpa began execution. The management of iron was pivotal in the ultimate configuration in the new circuit and one of the primary differences from the original circuit was the addition of a dedicated iron removal stage: Pressure Iron Removal (PIR). A significant drive for this new unit operation was to facilitate the separation of iron from other leach residues. Not only did this result in a significant decrease in the amount of leach residue but, without the constraints associated with iron precipitation during leaching, has permitted more aggressive leaching conditions and, correspondingly, greater throughput and efficiencies.However, as with many commercial implementations of even mature technologies, the journey from development to implementation has presented challenges for the continued ramp-up of the refinery to full nameplate capacity. Specifically, since all nickel bearing leach solution must pass through the PIR section prior to the nickel purification and recovery circuit, throughput difficulties in the PIR section can directly impact supply of feed to the nickel tank house. Since commissioning, the PIR autoclave has effectively removed iron from the refinery, but has shown significant variation in the solids phases produced in the autoclave. This variation presents difficulties for the filtration of the discharge slurry and represents a key throughput limitation which periodically impacts production. Additionally, the increasing production rates associated with the ramp-up of the refinery have resulted in a significant increase in the required volumetric throughput through the PIR process. This has placed even greater emphasis on improving the stability of the solid phase produced in the autoclave, ultimately targeting an easily filterable residue with high iron content."

Jan 1, 2016

By G. K. Quainoo

Investigation by researchers on the application of various thermo-mechanical process histories on 6000 series aluminum alloys have found improvements in mechanical properties of these alloys. However, natural aging, which is unavoidable in the automotive processing line, has been found to have deleterious effect on subsequent artificial aging properties in these alloys. In this study, the evolution of yield strength during natural aging modeled by Lloyd and Gupta has been adapted to investigate the effect of cold deformation on the natural aging kinetics in AA61 11 by means of tensile testing, differential scanning calorimeter (DSC) and scanning electron microscopy (SEM). Also, intermetallic particles in the alloy were extracted from the matrix and XRD performed on them to ascertain their composition and their role on the kinetics in the alloy. The results show that cold work effect on the natural aging kinetics of AA6111 is in very good agreement with the model proposed by Lloyd and Gupta. The kinetics of natural aging in AA6111 aluminum also decreases with increasing level of cold work. This is attributed to dislocations serving as sinks which consume quenched-in vacancies formed during the early stages of clustering. The phases of the intermetallic particles identified in AA6111 are those of a-A15Mn12Si7 and a-A15MnSi.

Jan 1, 2007

By A. Ghasemi

An alumina-silica coating was deposited on a nickel substrate by sol-gel process, and the structures and composition were evaluated, The sols were made from aluminium and silicon alkoxide, and an acid catalyst including HCl, To produce adherent silica coatings on nickel, various additives such as surfactant, viscose additive and drying control chemical additives were introduced to the system, and appropriate drying and firing cycles were applied after dipping in solution. The hot corrosion and oxidation resistance of the coating at different temperatures were investigated, The structure and uniformity of the coatings were examined by scanning electron microscopy (SEM), The results indicate that a uniform coating of alumina silica can be produced on a nickel substrate by optimizing the composition and process variables of the sol. Coatings can protect substrates from oxidation and hot corrosion at different temperature up to 1000°C, but is not very effective for hot-corrosion resistance at 1000°C.

Jan 1, 2005

By M. Fiset, D. Belley

"To better understand the wear process of various materials that may be used as blades on snow removal equipment, the first step is to evaluate the influence of the load applied and the moving speed on road wear rates of one type of steel and three types of polymers. While the behavior of steel conforms to Archard's law, wear rates of polymers increase to a power of ex of the load applied according to a model implying that the wear of these materials is due to fatigue. The wear rate of some of the polymers varies considerably in terms of speed, unlike the steel. The wear resistance of some of these polymers outclasses the steel tested as long as the speed is not too great. They, therefore, present interesting alternatives for snow removal on more fragile surfaces such as sidewalks and zone made of inter-block slabs.IntroductionSince the dawn of the Industrial Revolution, the massive use of machines has brought with it a number of different problems regarding wear. Snowplowing roads, parking lots and sidewalks is an activity that generates enormous expense in a country such as Canada. To better understand these wear processes and in the hope of stimulating new approaches designed to reduce the costs related to this sector of activity, this paper presents the behaviour of several materials (steel, polymer and rubber) as they wear on an asphalt-fines matrix surface lubricated with water. Also discussed is the effect of various parameters such as the load applied and speed."

Jan 1, 1990

By L. C. Bird, A. I. A. Salama, M. W. Mikhail

"A program of sampling in Canadian washeries was carried out by the Coal Research Laboratory (CRL) over a period of two years to evaluate the performance of various density separators in these operations(1). Operating data on quality and recovery of products, separation efficiencies and cutpoints for each separator type are compared with data predicted using computer models developed from previously existing data.The Heavy Medium Cyclone (HMC), Heavy Medium Bath (HMB) and jig models give predictions of recoveries and qualities of products for sizes coarser than 10mm with absolute value of error mean less than 7 per cent, whereas predictions of the Water Only Cyclone (WOC) model for -10mmfine coal are with absolute value of error mean less than 8 per cent. Although less accurate for -10 mm fine coal, the HMC and jig models produce predictions of recoveries with absolute value of error mean less than 2 per cent and quality of products predictions with absolute value of error mean less than 28per cent which are generally acceptable because more liberation in the fine fractions appears to compensate for any difference in the accuracy of separation, resulting in good prediction of the clean product. However, ash content of the actual fine refuse was lower than predicted. The difference is attributed to the highly friable nature of Canadian coals which tends to cause an excessive loss of coal fines to the fine refuse.A comparison study based on quality and recovery of products is made between the Dutch State Mines (DSM) models and the recently modified models, both produced comparable predictions."

Jan 1, 1985

By Bertrand Wolfman, William E. Stanley

"This paper reviews the traditional mine accounting systems, including ""custodial accounting"" and unit costing, and then suggests that the use of flexible budgets represents a more suitable method of reporting costs in order to assist the mine manager in improving productivity. Examples of various applications are given to show that the result is a clear reporting structure.Custodial Accounting is Emphasized in Traditional SystemsTraditional mine accounting has been mainly concerned with the accuracy of financial reporting to ""head office"" for the use of the directors and the company's bankers and shareholders. This is often called custodial accounting and it represented the main purpose of accounting when first developed in Europe hundreds of years ago. This important development permitted the establishment of enterprises which were separated from their owners because they could rely on accurate financial reports of management's stewardship.As custodial accounting is fairly broad and historical in nature, it is often not very useful to the mine manager for ongoing monitoring of performance of mining, milling, maintenance, and other support and staff groups. In spite of the considerable investment in accounting staff and computer support, many accounting systems have not been upgraded so that they accurately reflect workplace performance on a weekly or monthly basis.Budgets are Often FixedMany mines today also still emphasize fixed budgets. Thus, the mine plan which is set in the fall of one year is converted to a monthly tonnage and detailed dollar budget for periods of up to sixteen months in the future. The only certainty in this plan is that actual events will differ; timing, mix of mining methods and production volumes will differ on a monthly basis.Unfortunately, the fixed budget has no capability to reflect these operational changes. It is frozen for the full year. The result is that actual results will inevitably be compared to an outdated target."

Jan 1, 1982

By R. O. Grieve

"IntroductionCALEY (1945) and Evans (1950) pointed out that certain instances of convergence between Devonian and Silurian horizons, frequently evident in wells drilled for oil and gas in Ontario, appear to be related to local thinning of salt beds in the Salina formation and they suggested that leaching of the salt beds may have occurred. Exploratory drilling by Imperial Oil Limited since 1945 has brought to light several examples of structures similar to those discussed by Caley and Evans. The writer has had the opportunity to examine cuttings and data from wells which penetrated these structures and the attempt to interpret them in the light of the theory of leaching and subsidence proposed by Landes ( 1945a) to explain the marked brecciation and deformation of Upper Silurian and Middle Devonian sediments which crop out in the Mackinac Straits region of northern Michigan has led to the observations presented in this paper."

Jan 1, 1955

By Norman Lecuyer, Jacque Nantel

"The Chadbourne Project, located within the limits of the town of Noranda, Quebec, will make use of backfill materials to fill the voids left by the mining of stopes and pillars. A series of tests were conducted on different mixtures of slag and pyrrhotite tailings materials to evaluate their properties. The tests are described and some pertinent results are given in the paper.IntroductionThe Chadbourne Project is located in the centre of the Town of Noranda, Quebec, with houses as close as 120 m from the blasting operations. The ore is mined using the vertical crater retreat method. The voids left by mining activities will be filled. A program of pillar recovery will follow.Considering the proximity of houses and the need to recover pillars, the backfill program must be carefully laid out. No subsidence can be tolerated on surface.With these objectives in mind, a test program was undertaken by Nantar Engineering Limited and Queen's University to evaluate the possible ba ckfilling alternatives available to Chadbourne. One of the possibilities retained was the use of a backfill composed of broken slag material from the Horne Smelter and pyrrhotite tailings deposited on the Horne's pond a number of years previously.The back fill used at the Horne Mine until the mine closed in 1975 was composed of a mixture of 97% granulated slag and 3% pyrrhotite tailings. The tests leading to its use underground at the Horne Mine were described by Patton in 1952. The structural properties of the Horne backfill were ""intuitively"" known; it was agreed by all at the Horne Mine that the backfill was behaving remarkably well. Some were labeling it ""the best backfilling material in the world"". Its strength was said to be that of a weak concrete. All of the preceding indicate that the Horne backfill had never had its structural and other properties determined in the laboratory."

Jan 1, 1983

By Yuki Tsunazawa, Shuji Owada, Sho Fukui, Chiharu Tokoro

"Since the amount of e-waste has been rapidly increasing all over the world, there is a desire to develop the effective recycling process. E-waste has various kinds of electronic components with valuable and/or hazardous materials. Recycling of them is an important subject from the viewpoint of both the recovery of valuable materials and waste treatment. In common with all mineral processing, the comminution of e-waste is a key process because the liberation states after comminution determine the overall efficiency of metal recovery. Since some of useful critical metals are concentrated in a specific component, a special and selective grinding is expected to be effective. However, the knowledge about the mechanism and the effectiveness of the selective grinding is still limited and unclear.To better comprehend the mechanism, in this study, the investigation of comminution process using the particle-based simulation was conducted. Especially, this study focused on the comminution performance of printed circuit boards (PCBs), which are major components of e-waste. The behavior of PCBs and airflow in a drum typed agitation mill having flexible chains was simulated by the discrete element method (DEM) coupled with computational fluid dynamics (CFD). To model the shape of PCBs, the particle based rigid body model was introduced into the DEM. Since this model could not directly simulate the breakage phenomena, collision energy was calculated to qualitatively evaluate the comminution performance. In addition, the simulation results were compared with the experimental comminution tests using simulant PCBs where some capacitors were solder-mounted. These results indicated that comminution performance was affected by the rotation speed of the agitator. It was also demonstrated that the comminution performance was qualitatively evaluated using the particle-based simulation and this particle-based simulation made it possible to investigate the mechanism of e-waste comminution."

Jan 1, 2016

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005

By J. Robison, H. Pieterse, C. C. Smith, M. Luque, S. Chipman

Phase change during pressure let down releases significant amounts of energy that must be controlled to avoid undo wear and tear on equipment. Hydrometallurgical slurries require flow control equipment (valves and tanks) made of expensive materials to withstand the abrasive, and often corrosive nature of the slurry. Presented is a model of the nozzle of a let-down choke which is designed to control the flow pattern that exits the choke (valve) as it enters the receiving tank. This model can be used to design chokes which allow for the dissipation of the energy released during pressure let down by spreading the stream over a significant portion of the slurry pool in the receiving tank to minimize wear on equipment near the nozzle exit and the bottom of the slurry tank. An example uses the model to choose the nozzle expansion (area) ratio to select the outlet slurry velocity and slurry expansion angle.

Jan 1, 2004

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

This study examined the effects of pH and sulphate concentration on the surface charge and stability of alumina and pyrite dispersions. The relationship between these properties was investigated using measurements of electrophoretic mobility and settling velocity. The maximum aggregation for both minerals was observed near the iso-electric point (iep) where the force of repulsion is at a minimum. Aggregation decreased at pH values away from the iep, where an increased surface charge causes electrostatic repulsion between particles. Zeta potential data revealed that sulphate ions were adsorbed only on positively charged surfaces for both minerals. Adsorption of sulphates on the alumina surface increased aggregation by reducing the surface charge from >+25 mV to close to zero. These results indicate an electrostatic bonding of sulphate ions to alumina surface. Preliminary results on the interaction of pyrite and sulphate ions indicate a similar response.

Jan 1, 2004

The mixer that is commonly encountered in hydro metallurgical operations consists of a single turbine and tank combination. However, it would be advantageous to examine some common solvent extraction mixing systems in the light of the fundamentals of chemical reactor design. The basic concepts of reactor design are commonly used in the chemical industry, and it should not be too difficult to apply them to solvent extraction. The factors that affect the engineering design of a reactor are: the reacting system; the type of reaction; and the configuration of the reactor. The reaction system in solvent extraction consists of a heterogeneous liquid phase, involving two immiscible liquids. It is essential f or the process that the reactor product can be separated efficiently in the subsequent settler. The type of reaction in solvent extraction system may be quite complex, and the picture is complicated by the presence of competing and side reactions. The reactors themselves have been generally continuous stirred tanks, and the nature of the mixer-settler makes it unlikely that the pumping mixer can be dispensed with. However, it appears that there should be some definite advantages to a system of stirred reactors in series. The kinetic experiments which are carried out should have the definition of optimum reaction conditions as one of their goals. The data obtained from these experiments must also be applicable to the design of reaction equipment. Reactor selection and design is often a unique problem for each chemical process, and does not lend itself to a systematic general approach. However, the application of chemical and physical principles to mixer design in solvent extraction should result in practical, more efficient plants.

Jan 1, 1979

By Robert B. Parsons

"A study recently completed by the Prospectors and Developers Association, assisted by the author and computerized mine models he developed, presents a strong case that present tax rules severely handicap the junior exploration company relative to the established producer. This month, Tax Notes briefly summarizes the highlights of the study and some of the Association's ideas which came out of the study.IntroductionIn the case of any industry, a particular project or investment will generally generate a more attractive after-tax rate of return to a tax paying entity than to a non-tax paying entity: the ability to shelter current taxable income with tax deductions related to the project or investment can present a definite advantage as compared to shielding taxable income in the future with the same deductions. But, this advantage is probably seen nowhere more clearly than in the mining industry where the tax rules allow for substantial up-front write-off's. Studies show that the junior mining company which is earning no taxable income currently can be seriously disadvantaged, compared to the mining company which is currently generating taxable profit and paying taxes. This is particularly disturbing when one considers the importance of the junior segment of the mining industry. One might well ask where the equity is, in a tax system which causes the junior company to look at a deposit and see rock in the ground, when at the same time the deposit represents a viable mine to an operating company. This inequity and the importance of the junior mining company have been recognized to some extent in the income tax legislation. In recent years, the expansion of the rules for deducting certain earned depletion allowances against any source of income, and changes to improve the flow-through share rules, have gone part way in helping to put the junior on a more equal footing with the operating company. But it is questionable whether or not these helpful changes to the tax rules have done enough to alleviate the apparent inequities in the income tax legislation."

Jan 1, 1985

By M. Pearson, W. Bristowe, A. Hanson

"There's no such thing as quality assurance; only quality control ... by inspection. "(1) A common misunderstanding in the procurement and construction of custom designed, fabricated pressure vessels and piping systems is that quality assurance can be achieved by simply referencing codes, standards, ISO 9002, QMS or other such programs in the contract documents. In the authors' experience, nothing could be further from the truth, not detrimental to the performance of the equipment than the exclusion of inspection activities and reliance upon warranties and "fit-for-purpose" clauses. Likewise, the expectation that fabricators, suppliers, or third party inspectors can provide such assurances is also unrealistic where they have limited knowledge of the process, material selection criteria, or limited technical resources. The development and successful execution of a quality assurance program is a collaborative effort by engineers, designers, material suppliers, equipment fabricators, and field inspectors with the full understanding and support of the end user.This paper presents an outline of the quality control activities undertaken by the authors for several recently completed and on-going hydrometallurgical projects. The activities include: prequalification of fabricators and sub-vendors, shop audits, material validation testing, material source control and verification, positive material identification of weld metal overlay, specialised welding inspection, contamination control for titanium and titanium-clad fabrication, eddy current and mass spectrometer (helium) leak testing of shell-and-tube heat exchangers, hot cycle testing of titanium clad equipment, tolerance verification for refractory lined equipment, final inspection and cleaning.

Jan 1, 2004

By N. Haghdadi, D. M. Maijer, A. B. Phillion

B206 is a recently-developed high-strength Al-Cu casting alloy with reduced Ti and Fe, as compared to the well-known AA 206 alloy, for improved hot tearing resistance. In the current study, the solidification kinetics of this alloy as a function of cooling rate from 1 to 15 K/min were studied using differential scanning calorimetry (DSC) and microscopy. Specifically, the evolution in fraction solid, grain size, and secondary dendrite arm spacing have been characterized. The DSC results show the occurrence of three peaks during cooling from the liquid state, which are related to the formation of primary aluminum, a pre-eutectic intermetallic, and the eutectic phases. Thermal analysis also indicates that while the liquidus temperature is not sensitive to the cooling rate, the temperatures at which the pre-eutectic and eutectic phases form are strongly coupled to the rate of heat extraction. A decrease in the latter temperatures was observed when the rate of solidification was increased, leading to a lengthening of the freezing range of the primary phase. The results will be useful for improving B206 casting processes, specifically through modification of mould cooling conditions.

Jan 1, 2014

By W. G. Jeffery

"The mining and mineral industries have been, and remain, a major component of the Canadian economy. There are approximately 560 producing mining establishments of which there are some 130 metal mines and an equal number of non-metal mines, the balance being quarries for stone, sand and gravel. For 17 metals and minerals, Canada ranks within the top five as a world producer. There are 29 metallurgical plants. Employment in mining, smelting and refining was about 150000 in 1990. Mineral production, including coal, is about $20 billion. Exports up to the metal stage amount to $15 billion providing a positive trade balance of some $10 billion.The producing industry has a wide diversity of products. The companies range from small single mining operations to large multinationals. In terms of technology the industry has always been in the forefront of cost-effective practice, either using home-grown innovation or freely importing technology from around the world,The Mining Industry Technology Council (MITEC) makes an annual survey of the exploration and R&D expenditures of the senior mining industry that is the mining companies that are involved in mineral production from their existing mines. It does not include those companies solely involved in exploration using funds raised through equity sales.Table 1 shows the actual R&D and exploration expenditures as a per cent of sales. R&D shows a rising trend since 1988although the drop in value of output due to lower prices must be recognized as contributing to the increase. The point about this compilation is that the mining industry re-invests some 4070 of its sales in both exploration and R&D in order to sustain itself. Exploration for the renewal of metal inventories for future mining is a process unique to mining. It is not classified as R&D, and the necessity for this investment goes unrecognized by those who state that the industry does not do enough R&D."

Jan 1, 1993

By J. C. Kurnia

Presence of fine dust in air causes serious health hazard for mine operators resulting in such serious problems as coal workers? pneumoconiosis and silicosis. Major sources of dust appear of course along the mining face where the minerals are extracted. Proper control and management are required to ensure safe working environment in the mine. Presented here is the use of a computational fluid dynamic (CFD) approach to investigate the flow and dust behaviour in mining tunnels. The objective of this study is to propose and examine various strategies to mitigate dust dispersion from the mining face and reduce dust concentration to a safe level for the operator. In a companion study, the authors investigated various methods for mitigating dust dispersion from the mining face to ensure safe dust concentration levels in the mine tunnel. Among the examined methods, implementation of brattice to direct the flow from the main airway to the mining face is the most effective method to disperse dust particles away from the mining face. The installation of brattice, however, will limit the movement of mine operators and vehicles in the tunnel. Hence, application of a hybrid brattice which is a combination of a physical brattice along with suitable directed and located air curtains is proposed and examined. Based on the CFD simulation results, over a range of parameters of interest, it was found that the physical brattice blocks the ventilation air and directs it to the mine face while an air curtain located along the brattice outlet offers flexibility in keeping the dust away from the operator allowing more freedom for the operator and the equipment. Results of the modelling over a range of parameters of interest are presented and discussed with the goal of managing dust concentrations within safe limits for the operator.

Aug 1, 2013

By Gunther F. Leichtle, James A. Finch, Colin A. Hardie, Cesar O. Gomez

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibers for use in newsprint. The mineral processing group at McGill University in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network) has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University's flotation column test work at a Quebec wastepaper recycling facility.IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world's largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and U.S. municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World's solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity.A key to the success of producing quality recycled fibers from wastepaper is the deinking technology. The production of tissue papers, paper towels and newsprint requires regenerated fibers which are substantially free of ink particles. Of the various options available, mineral processing techniques can offer the most economical, environmentally acceptable and versatile strategies (Yoon, 1993). Today, it is recognized that flotation is one of the most effective processes for removing ink particles in the production of a high quality product. In a collaborative program with the Pulp and Paper industry, the mineral processing group at McGill University has adapted column flotation technology for this purpose. This article will describe the typical process of deinking from a mineral processing point of view (Part A). It will also present some results from McGill University's flotation column test work at a nearby paper recycling facility (Part 8)."

Jan 1, 1998

By Martha Gellner, Lutz Wuschke, Hans-Georg Jackel, Urs A. Peuker

"Electric vehicles are an alternative to the existing combustion engine driven cars. According to the EU Battery Directive a substantial recycling rate of at least 50 wt.-% has to be met for aged batteries since 2006. Existing recycling techniques are based on energy intensive pyro- and hydrometallurgical process, which are not able to recover all components. Aluminum and lithium for instance are slagged. The EU-Project “ABattReLife” investigated possibilities for a mechanical processing in order to create a sustainable process and a closed material loop from grave to cradle. After a sufficient liberation of the Li-ion batteries, components like the doped carbon black fraction (mainly lamination of electrode foils), the separator foil and the housing material can comparatively easily be separated from the other components by screening and air sifting. The remaining mixture consists of anode and cathode foils which have a similar free-settling ratio and are more difficult to separate from each other. A second comminution and compaction step modifies the particle size and shape as well as the degree of delamination. These changes influence the density of the electrode foils in order to improve the separation efficiency. Yield and purity of the generated metal concentrates were parameters to show if the separation was successful. The specific energy consumption for the different methods of processing was estimated in order to benchmark the cost-benefit ratio for each one.The studies have been accomplished with a zig zag sifter (model TUBAF), a hammer mill (model HM 340 Jehmlich) and with a Petkus-Sifter. Finally a process flow sheet was developed for a Li-ion battery recycling plant in pilot scale."

Jan 1, 2016