Search Documents

By W. B. Morrey

"In recent years, the major effort in detonator development has been concentrated on ""non-electric"" systems. Existing types all involve some form of explosive reaction to transfer ignition energy from outside the borehole to the pyrotechnic delay element contained within the detonator. These may be based on low-energy detonating cords having grained or plasticized explosive cores, shock tube energy transmission principals and explosive gas ignition systems. Each has properties of internal and external effects not present in electric conductors.The MAGNADET System introduces transformer coupling into electric blasting circuits. Safety features with respect to current leakage, stray currents of AC or DC source, electrostatic energy and radio-frequency radiation are comparable to ""non-electric"" systems, with advantages in simplicity, speed of hook-up and range of application.The transformer device used is a small ferrite ring or toroid which is an integral part of each specialized detonator. The detonator legwires form the secondary side of the transformer winding. The primary side is a single wire loop common to all units within the circuit. Power is supplied from a frequency-tuned portable exploder with unique circuit-sensing features.The MAGNADET System is expected to have particular application to shaft sinking, raising and tunnelling where the protective features as well as speed and efficiency are critical factors. Applications of the 'MAGNA' booster in quarries, open pits and longhole deck charges offer control over vibration problems and elimination of surface noise.IntroductionFor many years, electric detonators and electric blasting systems dominated surface and underground applications where controlled delay times were required. Control over the instant of detonation by blasting machines or power-line switches is the major safety feature.Electrical energy exists in many forms. It may originate from many sources. Electrical energy can be difficult to contain. It may enter or escape through a variety of conductive paths. It may fluctuate, concentrate or dissipate to pose a most elusive potential hazard."

Jan 1, 1982

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada's current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today's commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By J .. Carignan, Y. Dembele, J .. Guha, A. Fowler, A. Gobeil

The Barlow Lake stratigraphic section comprises the top of the Gilman Formation, the Blondeau Formation and the three sills of the Cummings Complex. Representative samples were analysed to allow characterization of the chemo-stratigraphic profile and geochemical affinity of the six rock facies found in the section. All the mineralized horizons are associated with sedimentary units. Geochemical signatures associated with the mineralizations are either very weak or very localized and shown by increases in K20 around the mineralizations and Fe203 near them. The mineralizations are stratiform, synvolcanic but resedimented and remobilized by regional metamorphism and possibly by hydrothermal activity initiated by the intrusion of the Cummings Complex. The evolution of the sedimentary basin with the decrease of its depth is confirmed by the chemo-stratigraphic profiles. Stratigraphic position in the section is important in order that the chemo-stratigraphy may serve as a guide for mining exploration in the distal facies of the Blondeau Formation.

Jan 1, 1984

"The last thirty years have seen enormous changes in all aspects of the gold industry, from the technologies of mining and extracting gold to the role it has played in the fiscal policies of nations. In this time, the market price of gold has increased ten fold and mine production has more than doubled. However, the cost of mining and extracting gold has also increased exponentially, and the industry has struggled with declining ore grades and increasingly refractory ore bodies.With the major economic powers of the world shrugging off the uncertainties of the post cold war era and moving into a period of unprecedented political stability, economic growth and low inflation, gold is also losing its lustre as a hedge against inflation and a backing for national currencies. Consequently, countries that had accumulated and hoarded gold for decades are now disposing of these non-performing assets, resulting in major swings in supply of the metal. Fortunately, this has coincided with the end of communism in many parts of the world and a tentative move to free market economies in most of the developing nations. As a result, people are becoming wealthier, and this is creating more demand for gold, principally in the form of jewelry.On balance, the shift in the role of gold, from one in which a significant portion of new gold production lay dormant in bank vaults as insurance against political or fiscal instability, to one in which most new gold is now freely traded as an industrial commodity, responding to normal market forces of supply and demand, has had a negative impact on the price of gold over the last fifteen years. In that time, the gold price has declined from a peak of $850/oz in 1980 to an average price of about $400 through the rest of the l 980's, to a price of -$320/oz today (1997). In large measure, this has been due to the enormous inventory of gold metal that was held by central government banks in vaults around the world, and which has been dumped on the market as soon as the price has started to trend upwards. Even today, after ten years of fairly steady selling by central banks, about 3 0, 000 tons of gold (or -8 years' supply at the present rate of consumption) is still retained in vaults (Murray et al., 1997).The downward pressure on the price of gold has created exciting opportunities for the development and implementation of new technology. Increasing the efficiency of gold recovery from more and more refractory ore bodies, whilst at the same time lowering production costs, have become critical to survival in this industry. These challenges have been met by the development and implementation of new technologies such as heap leaching, carbon in pulp, resin in pulp and the sulphide ore pre-treatment process of pressure leaching, bacterial leaching and fluid bed roasting. For an industry that saw very little technological change in the first seventy years of the twentieth century, the pace of change over the last thirty years must have seemed bewildering at times."

Jan 1, 1998

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Numerous schemes have been proposed in the past to evaluate the shear strength of rock discontinuities based on in situ and laboratory testing. Due to scale effects, in situ testing is the most reliable way to assess the shear strength parameters. However, practical reasons often impede this kind of testing. This is unfortunate because advances in theoretical rock mechanics are still dependant on qualitative experimental works. This paper presents a mobile high capacity shear apparatus developed for in situ direct shear testing of discontinuities along with testing methodology. The apparatus has the advantage of being simple, although of high capacity, and can be moved to different site locations for other tests. The in situ test was performed on a natural rock outcrop of schist with subvertical schistosity. A concrete block 50 x 50 cm with a base layer of high strength mortar was cast on the rock surface. Prior to the test, the concrete block was lifted and repositioned to have an unbonded joint but with interlocking asperities. The shear load was applied perpendicularly to the schistosity direction. The test was conducted in a constant normal load (CNL) condition. Both normal and shear loads were applied manually. The instrumentation consisted of two load cells for shear and normal loading, eight displacement laser extensometers for shear, normal, and lateral displacements and fourteen acoustic emission sensors for monitoring evolution of asperities’ degradation during the test. The friction angle obtained is 72° for the peak and 58° for the residual. The high values of friction angle indicates that first-order roughness and good interlocking of the joint surfaces can result in high shear strength parameter values in a rock generally regarded to have low values.

Jan 1, 2015

By E. Yalçin, A. Ünal

In transitional mineralization, the sill of the underlying variogram is relatively easily estimated, but the estimation of the nugget effect may be more difficult. This study aims to determine for massive copper deposits just how sensitive the estimations of ore reserve, economic copper content, total net value, and ultimate pit limits are to the errors of estimation in the nugget effect of the spherical variogram model. A massive copper deposit which has a log-normal distribution and a spherical variogram was simulated on a rectangular grid using the turning bands method. By using the three dimensional random kriging method, the mean block grades were estimated at four different sampling densities. The ultimate pit-limits were determined by using the two-dimensional dynamic programming algorithm. To calculate the estimation errors, the values obtained by using the actual nugget effect and structured component values were deducted from the estimations obtained using the incorrect nugget effect and structured component values. For isotropic massive copper deposits, it was found that the ratio of the nugget effect to the structured component of the spherical variogram has no significant effect on either the block grades estimated by the kriging method or on the ultimate pit limits.

Jan 1, 1992

By K. Nikkhah, N. Dhadli, G. Freeman

Ammoniacal pressure leaching operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation since 1954. Recent improvements have significantly increased the capacity of this circuit. The computer modeling of this process has proved to be a valuable tool in facilitating the evaluation of different operating scenarios in an effective manner. Reagent response in the ammonia leach of nickel and cobalt sulphides is examined using the dynamic process simulation capabilities of IDEAS(TM) software. The dynamic simulation enables accurate measurement of the sensitivity of the process to variables such as temperature, feed rate and ammonia concentration as well as compartmental analysis of metals concentration, pulp density, vent gas composition, and the formation of specific complexes. The complexity of the ammonia leach process makes it a logical choice for evaluation by computational analysis. The methodology for dynamic modeling of a pressure leach process is presented.

Jan 1, 2005

By Robert W. Plummer

"This paper describes the use of Geographic Information Systems (GIS) as a tool for mineral exploration by using the Eskay Creek area of northern British Columbia as an example. Data entry, analysis and output are discussed. Examples of some of the capabilities of the technology are presented.The main benefit of the technology is being able to perform complex and sophisticated searches of large and diverse data sets to highlight exploration targets. A GIS is a powerful data management tool that can be used in mineral exploration. It is a computer based system that is designed for the collection, storage and analysis of objects and phenomena where geographic location is an important characteristic. The main function of the GIS is to produce information for the geologist from a variety of sources (geology, geophysics, geochemistry, mineral deposits and so forth) quickly and efficiently. This allows the geologist to examine large amounts of data in a fraction of the time than can be done using conventional manual methods."

Jan 1, 1992

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By Norman J. Tienkaivip, Christopher J. Preston

"This paper describes the use of electronics for physical measurement and computer analysis in both open-pit and underground mining operations for the ultimate purpose of optimizing production blasts. Techniques in monitoring single borehole blasts using both pressure and vibration sensors to establish in-situ dynamic rock properties are outlined, including characterization of multiple borehole production blasts with regard to stress generation.Once field derived measurements are computer analyzed, they are channelled as input parallel to other data, such as the explosives thermochemical performance properties generated by a sophisticated computer program called ""HT-65"" into BLASPA . BLASPA, a blast simulation computer program, then couples these input with a mathematical model which defines the blasting processes. Aspects such as the blast geometry, explosive loads and distribution, hook-up, and costs are studied. The final output table gives specific blast performance or quality factors for each blast procedure. These results are then easily compared and rapidly optimized to achieve maximum performance at lowest blasting and drilling cost."

Jan 1, 1984

"Technological innovation is an extremely complex activity. The author presents his interpretation of innovation and the innovative process. He reviews the strategy used by participants in coal mining innovation in the past and discusses changes required to meet the challenges of the future.Introduction if an industry is to be successful and viable in today's world, the companies active within the industry must remain close to the frontiers of knowledge. The coal mining industry is no exception. Technological problems facing the coal mining industry are basically economic and social. Economic problems are those concerned with the long-term growth and profitability and social problems, with the health and safety of the mine worker and the impact of the mining operation on the environment.Technological innovation can be a key factor in meeting these problems successfully. The general belief is that the information base for technological innovation exists within mining companies and governmental agencies but current industrial and governmental strategies and structures impede the transformation of this knowledge into the mining products and processes required for growth.The purpose of this paper is to determine where Canada is in terms of coal mining on the innovative ladder. The paper as presented: defines innovation and innovative process; gives an historical ""broad brush"" review o f innovation in the industry; and suggests the challenges to be faced in the future."

Jan 1, 1985

By E. Ghali, C. Su, G. Houlachi

"The influence of lead ions on zinc electrowinning process was investigated by means of electrochemical noise measurements (ENMs) and cyclic voltammetry in conjunction with scanning electron microscopy and X-ray diffraction. All electrochemical experiments were performed in sulphuric acid electrolyte containing different lead ion concentrations as impurity. Lead was added in six trace levels between 0.05–0.8 mg/L in the bath. The lead content of the zinc deposits was dependent on the introduced lead concentrations. The overpotential associated with zinc electrodeposition shifted to higher values with the increase of lead concentration in the solution. An appropriate correlation was found between the different concentrations of lead in the electrolyte and the morphology of zinc deposit by ENM. The results showed that the increase of lead ion concentrations is generally accompanied with the decrease of skew and increase of kurtosis values that could be related to the morphology of zinc deposit. Effectively, the morphology changes from well-defined hexagonal platelets to large hexagonal, layered platelets and finally to non-symmetric refined crystalline structure, respectively.INTRODUCTION In commercial zinc electrowinning, zinc oxide is leached from the roasted calcine with an aqueous acid sulfate electrolyte. Then the zinc-rich solution is purified and transferred into an electrolytic cell. During electrolysis, zinc is deposited on aluminum cathode where lead-silver or pure lead is served as anode. Electrodeposition of zinc could be influenced by several parameters such as bath acidity, temperature, current density, the nature and concentration of impurities as well as additives in electrolyte. Metallic impurities play a complex role during zinc electrowinning and they can adversely"

Jan 1, 2016

By Robert B. Parsons

"There is a widespread concern that certain of Finance Minister Michael Wilson's Tax Reform proposals will likely lead to a significant decline in flow through funding after 1988. This does not bode well for the junior exploration sector, which relies heavily on flow-through to finance exploration programs. The exploration industry is actively pursuing various solutions to the problems posed by Tax Reform, in order to ensure that flow-through has a future.IntroductionWhile the proposals contained in Finance Minister Michael Wilson's Tax Reform White Paper may not be as far-reaching as some people had expected, nevertheless the combination of the existing tax rules and proposed new rules offers sufficient complexity to keep pencils sharpened for many months. After having had an opportunity to study Tax Reform since June 18, 1987, the sharpened pencils are suggesting that the White Paper is not without its shortcomings and pitfalls. Insofar as the mineral exploration industry is affected, there is widespread concern that adoption of certain Tax Reform proposals could spell near disaster for mineral exploration in Canada. More specifically, there seems to be a consensus among the industry, as well as some federal and provincial government officials, that the announced phase-out of the ""mining exploration depletion allowance"" (MEDA) would reduce the appeal of flow-through shares to the point where only a fraction of exploration funding would be financed in the future by flow-through."

Jan 1, 1987

By A. Bois-Brochu, G. Morin, G. Marin, M. C. Parr, J. Carignan

The presence of an alpha case on titanium parts produced by investment casting is problematic and has to be eliminated. The traditional techniques for the evaluation of its thickness are metallographic measurements and micro-hardness profiles. To obtain a better understanding of how the alpha case is formed with the underlying objective of limiting its depth, the present study proposes to characterize the microstructure and the chemical composition of the alpha case. Electron microprobe analyzer (EMPA) linescans were used to quantify the oxygen and substitutional elements that come from the mould and promote the alpha case formation. The chemical profiles were correlated with metallographic and microhardness measurements. For microstructure, optical microscopy (etched and polarized light analysis) was used. For phase analysis, samples were mechanically polished step by step and analysed using X-ray diffraction and optical microscopy. Furthermore, surface analysis techniques such as XPS and Auger Microscopy were evaluated but results were found to be inconclusive because the formation of the oxide layer was faster than its ablation and the matrix could thus not be analysed. The alpha case was observed on a Ti-6Al-4V step block casting.

Jan 1, 2014

By William E. Stanley

The paper examines the problems that arise in undertaking socio-economic impact studies to meet the requirements of environmental-impact legislation governing new mine development or expansion. An approach to undertaking socioeconomic impact studies is outlined, responses to specific problems are discussed and ways in which the mining company can use these studies to meet its general objectives are explored. The paper concludes by examining how a socio-economic study, as required by legislation, can be used to assist the mining company in achieving some general objectives it will have in developing a mine.

Jan 1, 1979

By Roger Moss

OUTLINE Area selection Mineralization/Alteration Styles Island Copper Mineralization Geophysics Geochemistry Coppercorp Setting Mineralization Geophysics Geochemistry Formation Common Characteristics Conclusions

Apr 1, 2005

By D. Lessard, S. Nantel

"Surface crown pillars are important Canadian,mining structures. Mines operating in the Canadian Shield usually have several, forming a first line of protection from surface elements.Detailed technical information from twenty-four Canadian hard rock mines show that the deposits dip steeply and are generally either single or multiple veins. Considerable overburden usually cap the deposits. The rock mass is often altered and intersected by important discontinuities.The designs for these types of pillars lack basic data and are based on experience rather than a scientific approach. Regardless of the competence of the rock mass, the surface crown-pillar thickness to width ratios (an unscientific design tool used by the industry) are usually less than five. Rock bolting is, in almost every case, used as a support measure. However, there are many openings neither backfilled nor monitored.The characteristics of openings with surface crown pillars are also examined."

Jan 1, 1988

By Per-Lennart Nystedt

"The Boliden Lead Kaldo Plant for the treatment of lead bearing flue-dust from the Copper Smelter and the Slag Fuming Plant has been in operation at the Ronnskar Works of Boliden Metall since the middle of 1976. At the present stage, the plant can treat lead-bearing dust of different kinds and compositions. The process allows good separation of arsenic and halogens from lead.The flue dust from the Copper Smelter and the Slag Fuming Plant is very complex and, apart from lead, also contains zinc, copper, tin, bismuth, cadmium, antimony, arsenic, sulphur, silver, chlorine and fluorine. The metallurgical process has been developed by Boliden Metall and has been tested on a pilot scale at the Foundation for Metallurgical Research (MEFOS) in Lulea, Sweden.The pelletized dust is smelted in the converter, where the heat is generated by an oil oxygen burner. The second step consists of reduction with coke. A lead bullion and slag are obtained. The slag, transported in liquid form, is treated in the Slag Fuming Plant for the recovery of zinc. The third step is the elimination of arsenic from the bullion. This is achieved by treating the lead with iron (turnings or pellets). The result is a crude lead and speiss. The lead contains silver, tin, antimony and bismuth, and is suitable for the final refining stages in normal plant equipment for refined lead.For process control, we use the rapid analysis centre, which is pneumatically and electronically linked to 'all major plant sections and allows for a quick turn-around between delivery of the sample and feedback of results. All three steps in the process are performed in the same converter.Since the starting up of the plant, the original process has been subjected to some modifications. Initial problems related to equipment, maintenance and environment have been solved step by step. Examples are quoted. Recent operating particulars are presented."

Jan 1, 1980