Search Documents

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By V. Polotski

This paper describes a platform for autonomous operations in open pit mining environments. A typical operation consists of: (1) Initial locomotion toward a remote worksite; (2) Pattern navigation within the worksite; (3) Worksite manipulations and (4) Return locomotion to the start location. The platform includes precise localization module based upon the fusion of odometry, inertial and GPS measurements. The guidance module starts from a set of way points specified on a GPSreferenced map and plans and executes the mission. A typical mission includes specified manipulative tasks along the navigation path. During motion execution the on-board system continuously verifies that the path is free of obstacles and that the hardware is not overloaded. Momentary losses of external positioning measurements does not adversely affect the performance, owing to the redundancy in position and heading estimation. A rehearsal phase follows planning and allows the supervisor to examine the kinematic behavior of the platform during motion, thus reducing the need for continuous monitoring during execution and providing protection against potential losses of communication.

May 1, 2003

By E. S. Moore

In the townships of Genoa and Marion, Subdury Mining Division, Ontario, there is a group of twenty-three mining claims known as the Jefferson claims. They are controlled by the Jefferson Mining Corporation and they were staked in 1908 by W. E. Smith, formerly of Sudbury, Ontario, and now of Smith & Reitz, a law firm of Minneapolis, Minnesota. These claims were staked for iron ore and in 1910 about 4000 feet of diamond-drilling was done on them. During the drilling operations galena and sphalerite ~were found in the iron formation in cores from holes, Nos. 2 and 3, claim W. D. 717, Genoa township. This discovery lead to a search for galena and sphalerite in the vicinity and a streak of rock containing these minerals was found in the iron formation a short distance to the east of. the drill holes. A shaft was sunk on this outcrop in 1912 to a depth of 8 feet and bottomed in an attractive lens of galena. Stripping revealed other small exposures of galena and sphalerite in the iron formation.

Jan 1, 1926

By B. Loveday, G. W. Delaney, S. Cummins

"Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage.The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed."

Jan 1, 2012

By Peter A. Witt

Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located some 75 kilometres southwest of Kamloops, B.C. (Figure 1). The ore is located within a porphyry copper deposit and is mined at a rate of 135,000 metric tonnes per day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 persons and is planned to operate until 2009. The operation is a partnership between TeckCominco with a 63.9% interest, BHP Billiton holding 33.6%, and others 2.5%. Management is shared by the two principal owners and directed by a management committee.

May 1, 2003

By Robert S. G. Chapman, Kieran M. J. Downes

The Sulphide-Preview Lakes area is located 45 km northeast of La Ronge in northern Saskatchewan. It lies within the southern portion of the Proterozoic La Ronge Volcanic-Sedimentary Belt. Two styles of gold mineralization are present in the Sulphide Lake area , stratabound gold mineralization is intimately associated with a pyrite-pyrrhotite-arsenopyrite-bearing graphitic argillite unit within a sequence of intermediate to felsic volcaniclastics. Past operators established three mineralized zones along this horizon with combined reserves for two of the zones, of about 175,000 tons at 0.22 oz/ton Au. In the Preview Lake area , gold mineralization occurs in variably sheared gabbro/quartz diorite sills within a mixed sedimentary-felsic volcaniclastic sequence. Gold occurs with arsenopyrite, pyrite and minor chalcopyrite associated with quartz veins and stringers. A sulphidebearing graphitic argillite unit occurs in close proximity to the mineralized shears. Past operators delineated seven mineralized shear zones, two of which were drilltested. Average gold grades reported are in the 0.1 to 0.2 oz/ton range with erratic values up to 5.0 oz/ton.

Jan 1, 1986

By J. W. McCammon

CRANGES in construction ideas and the continually rising costs of labour and conventional building materials, particularly since World War II, have prompted widespread investigations into the development and adaptation of new materials to meet the new requirements and to help reduce costs. Lightweight aggregates have been prominent in these investigations. The lightweight aggregates most commonly used today are foamed slag, cinders, pumice, diatomite, exfoliated vermiculite, expanded perlite, and bloated clay or shah. Lightweight aggregates contribute to the building industry in several ways: ( 1) in large structures the reduction in deadweight effected by the use of lightweight materials reduces the amount of reinforcing and structural steel necessary to support the structure; ( 2) the decrease in weight of lightweight blocks makes handling easier and faster; (3) pre-fabricated floor and roof slabs and tilt-up walls of lightweight concrete have become feasible and popular; ( 4) lightweight aggregate concrete has good nailability and is easily channelled; (5) concrete and plaster made with lightweight aggregate have good heat and sound insulation properties.

Jan 1, 1957

By Lorna Ortiz-Soto

A series of titiania- and silica-supported Au, Pt and Pt-Au catalysts prepared through different synthetic routes have been investigated in terms of their structural properties, adsorption of CO, and catalytic activity for the selective catalytic reduction of NO by propylene and the oxidation of and CO. Catalysts prepared by incipient wetness impregnation from individual Pt and Au precursors, exhibited characteristics very similar to those of monometallic Pt catalysts. This behavior is consistent with a model in which the two metals remain segregated due to their miscibility gap, and only Pt participates in the adsorption of CO and the reactions under consideration. In contrast, catalysts prepared from a Pt2Au4(C=CtBu)8 organo-bimetallic cluster precursor exhibited different behavior both in terms of CO adsorption and their catalytic activity for the three reactions examined. The combination of the kinetic, spectroscopic and structural characterization data suggests that in this case Pt and Au remain intimately mixed in the form of Pt-Au bimetallic particles, and that the presence of Au modifies the behavior of Pt.

Oct 1, 2003

By R. S. Forgan

The synthesis and study of a systematic series of phenolic oximes have shown that substitution in the 3-position can greatly affect extractive efficacy. Solid state, solution and gas phase analytical techniques, including X-ray crystallography, EPR and IR spectroscopy and collision induced dissociation mass spectrometry have been assessed for their applicability in interpreting the origins of differences in extractant strength. The dominant substituent effect on pH0.5 is the change in ligand pKa, with the more acidic ligands being stronger extractants. The influence of the 3-substituent on the stabilising intracomplex H-bonding of their copper(II) complexes also affects extractant strength. The 3-NO2 substituted ligand shows the lowest pH0.5 value, due to a combination of its low pKa and a stabilising bifurcated H-bond assembly around the copper(II) centre. Appending an aminomethyl group to the 3-position gives a ligand capable of binding a metal and its attendant anion. These metal salt reagents show potential to open up new flowsheets for the processing of high tenor copper feeds.

Jan 1, 2007

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By Desmond M. Levins, Reginald K. Ryan

"Removal of radium from uranium tailings would substantially lessen their environmental impact because it would eliminate, or greatly reduce, the hazards arising from radon emanation, leaching of radium, dust dispersal and gamma radiation. A process is described to extract radium from tailings by leaching in 3M Nael solution. The radium can be rapidly leached at ambient temperatures by either multi-stage contact in agitated vessels or washing on a tailings filter cake. Extraction efficiencies ranging from 80 to 94% have been measured for tailings derived from a number of Australian ores.Methods for radium recovery from the leach solution by precipitation, ion exchange and adsorption have been examined. Precipitation as barium/radium sulphate appears to be the most suitable approach. A possible flow diagram for the process is proposed which involves recycle of the saline leach liquor.IntroductionDisposal of mill tailings is the most contentious environmental issue facing the uranium mining industry. The conventional approach to managing tailings is to store them in a dam above ground. Attempts have been made to stabilize some tailings piles by physical or chemical methods. In a few cases, the tailings have been covered with earth and revegetated. However, most tailings piles from abandoned mills are in a neglected state and subject to the erosive and dispersive forces of nature. The cost of remedial action is high. The United States Department of Energy (DOE) has estimated that it will cost up to $130 million to rehabilitate abandoned mill sites in the U.S .A..Environmental authorities are now insisting that uranium mining companies improve their methods of tailings disposal. In the United States, the preferred approach is burial, either in mines or in specially excavated pits. Tailings retention systems as operated in Canada are regarded as storage facilities until an acceptable method of disposal is found. In Australia, the Fox Commission recommended that tailings from the Ranger project should be returned to the open-cut mine. Returning tailings to the mine has considerable merit, but it is not always a viable option. In many underground operations, it is not physically possible to fit all the tailings in the worked-out mine. In other cases, the groundwater hydrology of the mine may be unfavourable."

Jan 1, 1980

By J. A. Allan

"The history of the development and application of controlled recirculation systems in U.K. collieries is traced and the theory behind such systems briefly examined. Specific applications for dealing with dust and dust/heat problems in headings, for which practical experience is currently available, are described. Consideration is given to the special features which these systems introduce in the underground situation and to the essential safeguards which are required for their safe use.IntroductionRecirculation of air is a commonly used technique in genera l ventilation and air conditioning practice, but has always been regarded with some suspicion for mining applications. This is perfectly understandable in view o f the hazardous conditions which can occur with dangerous forms of recirculation in mines. However, certain controlled recirculation techniques can offer advantages, particularly in the field s of dust and climate control in headings, provided that they are designed, Installed an d managed with full comprehension o f all aspects of the system and always bearing in mind that from the point of view of serious firedamp ignition risk, headings are potentially the most hazardous places in coal mines.BackgroundProbably the first recorded use of deliberate recirculation in British collieries was reported by Lawton in 1933. This researcher described trials, undertaken under the auspices of a national committee on ""The Control of Atmospheric Conditions in Hot and Deep Mines"", involving attempts to increase the velocity, and thereby the cooling power on hot faces, by means of simple recirculation systems using fans and ducts delivering recirculated air in the opposite direction to the normal face airflow. No significant cooling advantage was obtained and there is no subsequent record of this work being continued. During the discussion on this paper, there was considerable disbelief that fire damp percentages had not increased significantly when air was recirculated, but apparently no attempt was made to establish why this should be. It is of interest to note that J. Ivon Graham, one of the contributors, recommended that recirculation should be tried in stone headings for the control o f dust, as he believed that ""there may be scope for recirculation and filtration of the air under certain circumstances in such headings"". This idea was not developed for another forty years."

Jan 1, 1983

By D. F. Hambley

"In designing are passes f or underground mines specific consideration should be given to unimpaired flow of broken rock, the dump point, and typical practices f or overcoming operational difficulties. Design features such as branches, bends, and knuckles should also be considered. This paper pro vides engineering information and various criteria for designing are passes, draw points. feeders, and support systems, together with several illustrative examples.IntroductionOre passes are the primary mean s o f vertical transfer of mined ore to the ore bins and loading pocket from which the o re is hoisted to the surface (Fig. 1) . While the words "" ore"" and ""ore pass"" are used here, such transfer systems ca n be used for any broken rock.The most extensive ore pass systems are found in caving and sublevel stoping mines. Extensive ore pass systems are also found in multilevel mines having steeply dipping orebodies. In more flat-lying orebodies , ore pass systems are sometimes used in conjunction with conveyor systems .Two decades have passed since the principles of the flow of bulk solids were formulated (Jenike, 1961, 1964; Johanson and Colijn, 1964; Kvapil , 1965). However, few published papers are available that discuss the design criteria for ore pass systems. Therefore, the aim of this paper is to provide the information necessary for good o re pass design .Rock Flow in Ore Pass SystemsIf an ore pass system is to fulfill its function, the transfer o f material must occur in an orderly fashion and in such a way that the full size of the opening is employed effectively. Apart from un controlled flow at the drawpoint, or outlet , whose design will be considered later in this paper, two occurrences may impede flow in an ore pass, namely:• Hangups due to interlocking arches.• Hangups due to cohesive arches.Prevention of each of these problems will be discussed in succeeding sections of this paper. A third problem piping, is related to the ratio of the drawpoint size to the o re pass size and will be discussed under drawpoint de sign."

Jan 1, 1987

By G. Kachaniwsky, M. Bédard

"The Noranda Continuous Smelting Process at the Home smelter was commissioned in March 1973. The ability of the process to handle a wide variety of feed materials and a steady stream of technical innovations in recent decades has served to maintain the Home as an efficient and versatile custom smelter. This paper reviews recent technological development and capabilities in areas such as sampling and preparation of secondary and complex materials, as well as the smelting and related environmental control issues. Future trends and improvements are also addressed.IntroductionThe Noranda Home smelter commenced operations in 1927. It was originally designed to treat 910 tonnes per day of copper concentrates and ores coming from the new Home mine site. In the 19305, the company opened its doors to other mines in northwestern Quebec. Treatment of feed materials on a custom basis has, therefore, always been an important factor in the operation of the Home smelter. Throughout the years, the Home gradually increased its custom smelting capacity, while maintaining its production from the Home mine. By the early 1950s, 65% of the materials processed was from outside customers, and by 1974, this figure had increased to more than 85% . With the closure of the Home mine in 1976, the company extended its smelting operations beyond ore and concentrate, and began to treat more scrap metals and residues rich in copper and precious metal content.Corresponding with the ever-changing pattern of feed sources, the Home smelter has adopted technological improvements to meet new and challenging business conditions. The technology of the original smelter of 1927has been completely replaced over the years in the quest for improvement. One of these major changes occurred in 1973 with the start-up of the Noranda Process Reactor. This extremely efficient smelting system has been exploited to treat a wide variety of copper and precious metal (PM) containing custom materials. This paper reviews recent developments and improvements achieved at the Home smelter, in the receiving, sampling and treatments of copper and PM scrap and secondaries, with particular emphasis on the development of new technology and equipment in complex feed materials treatment."

Jan 1, 1991

By Gene O. Cowie

"Zinc, which once enjoyed an unchallenged position in the field of decorative applications, has lost a substantial share of its markets to other materials, particularly plastics. This turn of events has led the zinc industry to explore new market areas, particularly those applications where the engineering properties of zinc can be utilized. This paper gives an overview of the zinc industry's efforts to develop the data base and product development technology which have enabled zinc alloys to emerge as engineering materials. It also indicates those areas in which the research facilities of the zinc industry must be employed to ensure that zinc alloys keep pace with developments in competitive materials and processes.The Materials RevolutionThe development and utilization of new materials and manufacturing processes progressed for centuries by evolution. Recently it erupted into a revolution, which may become as significant as the industrial revolution. The materials revolution has impacted upon many industries, but none has been affected more traumatically than the North American automotive industry. The plight of that industry is of great importance to us because their problems have, to a great degree, become problems to the zinc industry.Much of the impetus behind the automotive trauma came from the battery of motor vehicle regulations promulgated by the United States government in the 1970s. These regulations required that the efficiency of passenger cars, in terms of miles per gallon, be approximately doubled in ten years. In view of the fact that major changes in the automotive world require three years of lead time to implement, the industry was left with only seven years to perform the task. The automotive industry was simultaneously required to make progress in other areas, such as reduced emissions, reduced cost of repairs and increased levels of occupant safety. These added demands not only diverted some of the available resources away from efficiency goals, they often ran in direct conflict. For example, when you are required to provide a front bumper which will absorb the energy of a 5-mile -per-hour barrier collision, you must add both hardware and structure to the vehicle. This adds weight, and increased weight reduces miles per gallon."

Jan 1, 1983

By J. W. Hendry

"This paper will discuss the application of tools and the evolution of computer-assisted procedures in the production planning process at Quintett e Coal Limited (QCL). In 1986, QCL produced 5.3 Mt of clean coal from their surface mining operation located in north eastern British Columbia. The structural complexity of the sedimentary deposit and high rate of mining necessitate the consideration of large amounts of geological information which continually updates the interpretation. There are multiple unit operations required during the process of mining through a given multi-seam sequence, which results in many interdependent faces, and multiple iterations of scheduling sequences in order to satisfy a given set of objectives. In order to facilitate these activities in a timely fashion, it was recognized that a computer systems' capability needed to be developed which could increase the efficiency of information input, manipulation and output. IntroductionQuintette Coal Limited (QCL) has been operating a large metallurgical open pit coal mine in northeastern British Columbia, since 1982. The mine produced 5.3 Mt of clean coal in 1986 for export to Japan. Throughout the start-up period and the subsequent build -up of production levels, it became evident that the primary producing area was comprised of extremely complex faulted structures. This has resulted in development and modification of specialized mining methods employed to effectively recover the resource. Similarly, the planning and engineering techniques employed have been evolved over the same period of time. The implementation of computerized methods has been one of the major developments in this process, including geology interpretation, modelling, reserve definition, quantification, production planning and scheduling, and graphical plan presentation. These capabilities have been employed, in various forms, for project scale feasibility work and long range planning for some time, however, the use of computer tools for short-term, detailed production planning of a complex mining environment presents a different set of problems. It is hoped that a presentation of the current state of evolution and future plan s for development will be of interest to organizations considering implementation of a similar system."

Jan 1, 1988

By Tony B. Szwilski

"The efficiency of operation and life of an advancing longwall coalface depends, to a great extent. on the face-end roof strata conditions and the stability of the gateroads. The factors that influence the rate of closure of gateroads are examined, in particular the gateside pack and the coal rib (crush) pillars. The performance of mechanized packing systems is briefly discussed. Gateroad deformation surveys were carried out at two coal mines to determine the influence of the rib pillar width on gateroad stability; also, the influence of the gateside pack on the immediate roof and floor strata is analyzed based on strata bed displacement measurements from instruments installed in the gateroad and pack-hole of a longwall advancing face operating in a thick seam (7.55 m). Concluding, an evaluation of the fac e-end systems examined is given and recommendations made f or the most suitable rib pillar width. face-end geometry and roof strata reinforcement.IntroductionKevword s: Coal mining, Pillars, Rib pillars, Ground control, Longwall mining, Gateroads , Packing systems, Roof control. The face-end region of a longwall advancing face is the center of mining activity, being the turn-around point for the coal cutting machine. and the place of gateroad formation and movement of special face-end supports. The design of face-end layouts can be aided by knowledge of strata control parameters, such as the effective loading of the immediate roof strata , convergence of the roof and floor, magnitude and distribution of fractures in the roof strata around the face-end , optimum placement of supports, coal seam thickness and strength characteristics, geometry of layout and interaction from neighbouring workings. Generally, the gateroad is formed by one of three face-end methods: (a) advanced headings, (b) in-line system (gateroad formed at the face) or (c) conventional ripping with or without stable elimination (also halfheading). The quality of gateroad is influenced principally by the face-end system employed, standard of gateside pack and width of pillar. A good standard of gateroad is generally achieved by employing the half-heading face-end system, the gateside pack and coal rib pillar having comparative support/ yield (stiffness factor) characteristics. However, the halfheading is often not favoured due to face operation restrictions."

Jan 1, 1981

By Gerhard Heinrich

"The composition and the possible utilization of a slag sample from a nickel smelter operation in the Sudbury district were investigated. The sample containing 0.136% Ni, 0.10% Co and 0.29% Cu could be characterized as a fayalit e slag with a sulphide bearing glass matrix. While the fayalite contains most of the Co, Ni is enriched within both sulphides and fayalite. Cu is only present in higher amounts in sulphides or metallic droplets. This, as well as the small grain sizes of the mineral phases, inhibits significant enrichment by mechanical methods. However preconcentration is possible by means of magnetic separation. An effective hydro metallurgical approach proved to be oxygen pressure leaching with sulphuric acid. Accordingly, the method proposed for processing the investigated slags is to combine the normal utilization as coarse construction material with pressure leaching of the fines and the ground upgraded magnetic fraction. Besides the recovery of base metals, the leaching process yields fine-grained residues, which, after addition of CaD, will set to a cement-like material, or can be used as a pozzolanic cement colour. INTRODUCTIONDuring the pyro metallurgical processing of nickel ores, the valuable metals nickel, cobalt and copper are enriched within the sulphide matte, similar to the smelting of copper ores. The resulting waste materials are slags, which may still contain valuable metal contents of up to 0.5% or above . These contents are close to the cut-off grades of some nickel-cop per-cobalt deposits. The methods that are used to recover copper from slags comprise in general further pyro metallurgical treatment, often after enrichment by flotation. Another area of application for such slags is their use as construction material. However, this might cause environmental problems if nickel containing dusts are produced.Based on one example, the characerization and a possible way of complete utilization of nickel smelter slag s as construction materials in combination with partial base metal recovery are described in this paper. The investigated slag sample was obtained from a dump site in the Sudbury district, Ontario. Detailed test series for process optimization were not possible during this study due to the limited available sample size."

Jan 1, 1989

By Susan W. Campbell, Bruce Regensburg

"The CIM Careers Task Force has addressed industry's concern of a perceived shortage of skilled personnel over the coming decade. The industry is faced with a fundamental shift by young Canadians away from scientific and engineering careers, coupled with the fact that today 's students know little about the minerals industry and have a poor image of it.The responses to two questionnaires which were distributed to CIM members, government, professional associations, and educational institutions, formed the backbone of the Task Force position paper, which presents a shopping list of ideas and initiatives for consideration and to facilitation by the various organizations concerned.Tackling the image of the minerals industry is part of the answer to the careers crisis. On the positive side, the minerals industry provides the allure of a treasure hunt for young people and is seen as a significant contributor to the economy. It is understood to be well paying, provide good opportunities for advancement, individualism, and travel, and to be rich in esprit de corps. Enhancement of these positive aspects of the image can take place at all student age levels.Numerous initiatives tackle the negative aspects of the image. Young people perceive the industry to be environmentally damaging, which is the most crucial aspect that needs to be addressed. The industry is seen as still in the pick-and-shovel days and as a sunset industry that is running out of ore. Work in the minerals industry is perceived as dangerous and lacking glamour. And finally, the perceived remoteness of operations and exploration is seen as a drawback to a largely urbanized student group.Tackling young peoples' curiosity and interest in the minerals industry throughout grade school and encouraging postsecondary science and engineering students to enter the minerals industry by ensuring summer employment is the second part of the equation.The CIM Careers Task Force position paper develops strategy to attract and maintain interest of students in grade school, junior high, senior high school, and in post-secondary levels. The strategy outlines initiatives targetted at each of the educational levels and action plans to accomplish the objectives."

Jan 1, 1993

By T. H. North, A. G. Glover, R. J. Pick

"Girth welding operations represent the rate-limiting step in pipeline construction. A joint industry-university program was set up to establish the field welding characteristics of large-diameter, high-strength line pipe.Theoretical work carried out at the University of Waterloo showed that pipe wall thickness and joint misalignment prior to welding has a marked influence on the lifting stresses acting on the root pass of girth welds. Pipe diameter and pipe ovality had negligible effects. Super-position of lifting and residual stress (caused by the fusion welding operation) highlighted regions of the weld bead most susceptible to hydrogen-induced cracking.The field welding characteristics of 1219-mm-diameter, 13.72-mm-wt Grade 483 line pipe were evaluated using a specially designed test rig. The principal test variables were lift height, delay time after root pass deposition, preheat temperature, pipe composition and joint misalignment prior to welding. For any given life, preheat and joint misalignment prior to welding had the most significant effect on cracking tendency.The output of this program has industrial significance and illustrates the beneficial features of university-industry collaboration.IntroductionField welding operations comprise the rate-limiting step during pipeline construction. Crack-free girth welds must be made in a wide range of weather conditions and consequently the field weldability of line pipe compositions directly affects pipeline integrity and construction economics.Pipe-laying practice comprises root bead deposition followed by a skidding operation involving lifting (or lowering) the pipe length onto skid s so that the next pipe length can be aligned prior to welding. Consider pipeline construction using 24.4-m lengths of 1219-mm-diameter , 13.72-mm-wt Grade 483 pipe weighing approximately 10,000 kg. Skidding involves loading a 3-mm-thick root bead by moving the free end of the pipe through vertical distances of up to 700 mm . The likelihood of cracking in these circumstances depends on the inherent crack susceptibility of the pipe composition employed, on the hydrogen content of the deposited weld metal and on how well the joint handles the external stressing caused byskidding."

Jan 1, 1981