Search Documents

By H. Cay, J. Zachwieja, T. Esplin, R. Ravenelle, T. Olsen-Tank

Barrick Goldstrike mine utilizes a carbon-in-leach (CIL) circuit to simultaneously leach gold into solution with cyanide and adsorb the gold-cyanide complex onto activated carbon for further refinement. If the gold bearing ore contains a significant amount of native carbonaceous material, gold cyanide can be adsorbed at these sites instead of onto the desired activated carbon and the gold is effectively lost to tailings in a detrimental process known as "preg-robbing." The preg-rob effect is considerably reduced by treating the ore with a surfactant, which is hypothesized to adsorb to and passivate the native carbon surfaces. Past laboratory and pilot studies have consistently demonstrated significant gains in gold recovery after treating carbonaceous ore with surfactant. With success in bench and pilot scale testing, a plant trial was conducted at Barrick Goldstrike to evaluate the feasibility of using an alkoxylated fatty amine surfactant (Ethomeen T/12) to aid in the leaching of high preg-robbing ores. This paper analyzes the performance of the surfactant during the plant trial in addition to the problems that occurred during the trial period. Suggestions for improvement are also discussed.

Jan 1, 2014

By C. Campero, C. Nicolau, L. Pagliero

The Chilean Congress has recently promoted desalination as a solution to meet the mining industry’s growing water demand. However, this rapid expansion of desalination infrastructure comes with trade-offs. This includes a significant energy cost for treatment, as well as socio-environmental impacts on indigenous communities, tourism, fisheries, and the marine ecosystem. This paper advances a regional-scale model for analyzing competing trade-offs through a case study in the Antofagasta mining region of Chile. Through geospatial data analysis in ArcGIS, new desalination infrastructure investments supplying water to mines are overlain with features of concern raised by communities during the environmental impact assessment (EIA) process, such as national parks, fisheries and exploitation areas for benthonic resources. The resultant model provides a test-bed for analyzing the cumulative effects associated with desalination expansion and for investigating scenarios to mitigate negative social-environmental impacts. The model simulates alternative scenarios for desalination locations and pipeline routes according to competing constraints (i.e. to minimize cost and energy constraints while also avoiding ecological and social hotspots). The ultimate contribution of the work is a demonstration of how the proactive adoption of a regional-scale infrastructure planning might have led to different desalination investment decisions. INTRODUCTION Chile represents the largest producer of copper globally, and holds approximately a third of the world’s estimated copper reserves. However, access to water represents a major constraint to industry expansion and creates conflicts with competing water users (Aitken et al., 2016; Côte et al., 2010). Recently, the Chilean Congress has promoted desalination as a solution to meeting the industry’s growing water demand, which is likely to lead to significant growth in desalination infrastructure to support large-scale mining projects that extract freshwater over a rate of 150 l/s1. By most recent projections, the Chilean copper mining sector is set to increase seawater use by 230% by 2029 (Faversham House Group Ltd, 2019). By the year 2015, Chile had 11 projects serving the mining industry and there are at least other 12 planned plants (Cochilco, 2015). While the use of seawater allows continued expansion of the sector without depletion of scarce underground aquifers, it is nonetheless accompanied with important socio-environmental drawbacks. One such challenge with desalination is the associated energy costs, expressed, both economic and environmental (e.g., CO2 emissions). This includes the energy required for reverse osmosis treatment facilities, as well as to pump water to inland regions at high elevations around 3.100 m.a.s.l in Chile. (Dixon, 2013; Knops et al., 2013). Additionally, the impacts of desalinated water use on flotation chemistry are generally poorly understood, necessitating the need for further research into the impacts, both positive and negative (Cisternas and Gálvez, 2018; Liu et al., 2011).

Jan 1, 2019

By F. J. McMulkin

This paper, the 1965 Airey Memorial Lecture, reviews the world-wide technical advances in iron and steelmaking, and offers an appraisal of the new techniques which will be applied in the future. After a review of blast furnace operations, the continuous steelmaking process is described, and the resulting techniques of degassing and continuous casting are discussed at length. Pressure pouring, hot rolling, cold rolling and coating practices are also outlined, and considerable space is devoted to the direct reduction process. Finally, the application of the computer to steelmaking operations is discussed in some detail.

Jan 1, 1966

By M. L. Goble

"Inco Metals Ltd. (Manitoba Division) operates a mining, milling, smelting and refining complex, 500 miles north of Winnipeg in central Manitoba. The Thompson Mill is presently operating at 12,000 S.T.P.D. on ore from both underground and open pit mines. The ore is treated in two separate milling and flotation circuits utilizing a common crushing system which is located inside the main mill building. The milling facility employs approximately 43 operating employees, 30 maintenance employees and 20 staff in supervisory or process development roles.In recent years an increasing awareness of the potential hazards of contaminants in the work place has made it mandatory that all employers maintain careful and accurate records of the work environment to which each employee has been exposed during his working career.The importance of this record keeping and general observation of the work place cannot be over emphasized. Proper monitoring of the work place provides an accurate and complete record of the contaminants and physical agents to which an employee is exposed during his work career. This can aid in studies which might be conducted in the future and can also be used as a basis for instituting improvements to the workplace."

Jan 1, 1980

By D. S. Salonine

Aluminum alloys offer a wide range of capability with a unique combination of advantages that makes them the materials of choice for numerous products and markets. One of the most important applications is their use as the primary structure and outer envelope in aerospace vehicles. Wide and thorough studies on hot working and microstructure evolution of aluminum alloys have been made in Russia. The most important appear to be: - introducing the structure diagrams in strain rate - temperature coordinates which show areas of different microstructures (non-recrystallized, recrystallized, and mixed) after the hot deformation and the following heat-treatment for common aluminum alloys (Yu.M. Vainblat); - studying the press-effect ("structural effect" by V.I. Dobatkin); - learning the influence of hot worked substructure on aging mechanisms; conducting researches on press heat-treatment. These works allowed a deeper understanding and a better control of the mechanical behavior of aluminum products. Comparisons are made to equivalent developments in Europe and America.

Jan 1, 2004

By Bradley Stoughton

It is very easy to reduce iron ore at a temperature well below its melting point and produce a more-or-less-pure metal which can be used directly for implements, tools, or machines. This simplicity has been the cause of much money loss by persons who were so satisfied with the successful operation of a process that they paid all too little attention to the commercial aspects of it. How easy a direct process is may be gleaned from the fact that it was practised with some -success by primitive man, and has been in almost continuous operation in one form or another for a period of probably 4,000 years. The production of steel in ton lots, beginning about 1860, brought a new phase into the economic situation, which, however, had been already greatly modified in 1784 by Henry Cort's invention of purifying pig iron. Direct processes survived both of these revolutions, under special geographical conditions, even up to the last few years of the nineteenth century, but ceased to have any general use as the basis of supply for structural, machine, or tool industries even in countries which could have manufactured iron by a direct process, but, instead, imported the product of established iron and steel processes. And this is still the situation today, notwithstanding the invention of an incredible number of 'new' processes since 1900, most of which are abandoned, and only survived as along as their financial backers were willing and able to Jose money. Probably none of these processes failed to work pretty well, and all seemed to show a handsome profit on paper.

Jan 1, 1930

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

By H. Aminian

Gold powders have many important industrial applications. In this paper the available processes for the preparation of gold nano and micron sized powders are described. The attention has been given to hydrometallurgy route and the recent works and achievements in controlling the powder morphology are highlighted.

Jan 1, 2011

By S. Steinlechner, S. Wegscheider

"In the past, the metallurgical industry was most of the time dedicated on their main commodity, recovering base metals like zinc, copper or lead but leaving other valuable side elements in the generated residues. As a result, these accompanying minor elements, like gold, silver, indium or also PGMs can be found in the dumps of the corresponding industry. Because of political unrest, strikes, economic reasons or decreasing primary resources leading to a high supply risk, also those mentioned minor elements moved into the focus of the recycling industry. Therefore, beside the base metals, first of all the recovery of those minor metals would be of high interest contributing to the economic viability of recycling processes, although they occur in much smaller quantities in materials. In this context, residues from zinc industry, like leaching residues or precipitation residues show high potential to carry silver as well as indium next to lead and zinc. Therefore, the paper summarizes carried out thermochemical calculations investigating a possible recovery of silver as well as indium by volatilization and the influence of zinc and lead on this process. Based on these theoretical investigations with HSC, trials in lab scale were done verifying the obtained results.INTRODUCTIONHuge amounts of iron precipitate, mainly jarosite get landfilled every year although there is a high content of valuable metals in this residue beside iron. Nevertheless, jarosite has to be dumped due to the presence of contaminating heavy metals. The accumulation of these residues takes up massive land on the one hand but also causes a series of environmental problems in ecosystems on the other. Moreover, some toxic ingredients such as arsenic and cadmium can be dissolved in rain water and are therefore harmful to the health of the aquatic systems. (Erdem & Özverdi, 2011; ÖzverdI & Erdem, 2010) Approximately 0.5 t of dry jarosite accumulate in the production of 1 t of zinc by the hydrometallurgical zinc-winning route (Svens, 2010). Jarosite is a precipitation residue formed during the iron removal. In general, the iron already exists in the zinc ore which is why zinc ferrite builds up during the roasting step of the zinc ore. Zinc ferrite is only soluble in strongly acidic solutions and during the hot acid leaching step it gets dissolved while zinc and iron enter the solution. It is necessary to get rid of the iron because otherwise it would deposit on the cathode first due to its precious character which would be harmful in the zinc-winning electrolysis. Nevertheless successful investigations were done by adding chlorine to the jarosite to recover silver. These findings leads to another residue which occurs in huge amounts – electric arc furnace dust (abbreviated with EAFD) from the iron and steel industry. In 2013 the annual electric steel production reached about 451 million tons. Around 15-20 kg of EAFD is produced per ton of steel in an electric arc furnace (EAF), creating approximately up to 9 million tons of dust per year. (Grabda, Oleszek, Shibata, & Nakamura, 2014; World Steel Association) Next to elements like zinc, lead and iron, chlorine and fluorine are present in this dust. While galvanized steel plates in the scrap act as a source for zinc, casting powders, flame retardants and synthetic coatings are responsible for the chlorine and fluorine contents in the dust."

Jan 1, 2016

By G. A. Bezuidenhout, J. Davis, S. M. Bradshaw, J. P. T. Kapusta, D. K. Chibwe

"This research work forms part of an assessment to complement the feasibility of implementing high pressure sonic injection into relatively small (2.25 m I.D by 3.66 m I.L) Peirce-Smith converters (PSC) used at Lonmin Plc. Work has been carried out to characterize the fluid dynamics of three-phase (air, matte and slag) fluid flow in these converters using Computational Fluid Dynamics (CFD) simulations. The investigation has been done to study the flow pattern of the three phase system at high air pressure injection achieving sonic velocity at the tuyere exit into the converter. The 2-D and 3-D simulations of the three phase system were carried out using the volume of fluid (VOF) and realizable k -e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were implemented using the commercial CFD numerical code FLUENT. A detailed study of the flow pattern has been presented in the form of contour plots and the results obtained are useful for understanding plume extension and velocity distribution, shear wall stress distribution, and phase distribution characteristics in the system. The results provide a basis for further development of sonic injection technology into relatively small industrial Peirce-Smith converters with the ultimate objective of achieving lower energy consumption, improved process efficiency and increased throughput of the converting process. INTRODUCTIONPeirce-Smith converters (PSC) have been used in copper (Cu) and nickel (Ni) making smelters for more than a century for the purpose of removing iron (Fe) and sulphur (S) chemically associated with copper-nickel mattes through exothermic oxidation reactions. This process is commonly referred to as conversion. In principle, conversion is a submerged injection process, where typically air (or oxygen enriched air), at subsonic velocity (typically < 150 m/s), is laterally blown into liquid matte (Cu-Ni-Fe-S system). Oxygen preferentially reacts with Fe and S to produce iron oxide (FeO), which is slagged off, and sulphur dioxide (SO2), which reports to the process off gas."

Jan 1, 2012

By Jacob Masliyah, Zhiang Zhou, Tshitende Kasongo, Jianjun Liu, Zhenghe Xu, Jeawon Choung

"Slime coating is a recognized challenge in fine particle flotation, not only in decreasing recovery, but also in reducing the selectivity and hence froth quality. In this presentation, a novel method based on electrophoretic mobility distribution measurement to study slime coatings is described. By measuring electrophoretic mobility distribution of individual minerals and their mixtures, the interactions between these minerals can be evaluated.For illustrative purposes, a model system of fine coals, or oil sands with two different types of fine clays was studied. Flotation tests showed a significant decrease in coal (bitumen) flotation recovery with montmorillonite but not with kaolinite clay addition. When electrophoretic mobility distribution of a fine coal/montmorillonite clay mixture was measured, a single modal zeta potential distribution was obtained, in contrast to a bimodal distribution for fine coalkaolinite clay mixture. This finding suggests a stronger adhesion of montmorillonite than kaolinite clays on fine coal surfaces. In the case of bitumen, the bimodal zeta potential distribution was measured for the mixture of bitumen emulsion and kaolinite or montmorillonite, indicating a weak attraction of the clays by bitumen. In the presence of calcium, however, a single modal zeta potential distribution was obtained in the mixture of bitumen emulsion with montmorillonite but not kaolinite clays. These findings are in excellent agreement with bitumen flotation results, demonstrating that the electrophoretic distribution measurement is a powerful tool to study slime coating phenomenon in a complex fine particle flotation system."

Jan 1, 2002

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By Steve Cole

"The economic and strategic importance of PGE bearing deposits is fuelling renewed exploration and development efforts in the precious metals mining sector.This paper presents a review of the various techniques used in the processing of PGE bearing ores, from primary benificiation to processing routes for the different flowsheets that have been developed amongst current producers. Recent innovations such as preconcentration of ore using gravity separation, recent trends in flotation circuit design and the development of hydrometallurgical routes for the direct treatment of flotation concentrates without the need for smelting will be discussed. Data from recent projects will be presented to illustrate common characteristics of PGE ores and concentrates.INTRODUCTIONThe six platinum-group elements (PGE): ruthenium, rhodium, palladium, osmium, iridium and platinum, together with gold and silver, are considered to be ""precious"" metals. The recent spike in platinum and palladium prices coupled with the projected increase in demand for the metals has fuelled a spate of exploration and new projects in the PGE sector. Historically primary producers of PGE metals have controlled the flow of information relating to the mining and processing of these ores into the public domain. Very little published information relating to individual operations and processes is available in comparison to the abundant literature relating to other metals.The purpose of this paper is to provide a general overview of the issues relating to the processing of PGE ores. Each topic discussed could easily be the topic of a paper or book and so in many cases only the surface of the topic will be scratched. An attempt has therefore been made to provide as many references as possible.This paper discusses the classification and location of PGE ores, the mineralogical factors that affect recovery of PGE's, methods currently used for recovering PGE's and process trends in PGE metallurgy."

Jan 1, 2002

By R. D. Brown

In his April 10, 1978 budget address, Finance Minister Chretien declared that the federal government will restrict the growth of its spending to less than the trend growth of the gross national product; over the past year, both the federal and a number of provincial governments have taken action to cut back on spending policies. This new emphasis in restraint would seem 10 be a response to a mounting public reaction to the rapid growth of government spending - and taxation - over the past 25 years. Although this relatively new government posture on public spending may be admired by many, to others it raises the question: "Can the growth in government spending really be stopped?" This article comments on just how government revenues - and spending - have grown over the past few years in Canada, and mentions some of the issues relating to a slowdown in that growth.

Jan 1, 1978

By Réjean Lévesque

SIDBEC-NORMINES a été incorporée en 1976. Depuis la fin de 1977, ses activités comprennent outre la concentration au lac Jeannine, près de Gagnon, du minerai de fer extrait du gisement du lac Fire, I&apos;exploitation d&apos;un atelier d &apos;enrichissement secondaire et une usine de bouletage à Port Cartier. L &apos;objectif principal de SIDBEC-NORMINES est de produire six millions de tonnes de boulettes d&apos;oxyde de fer par année, dont trois millions auront une faible teneur en silice afin de répondre aux exigences de la réduction directe. Les installations de SIDBEC-NORMINES sont adjacentes aux installations portuaires de la Compagnie Minière Québec Cartier, à l&apos;est de la ville de Port-Cartier. L &apos;ensemble est conçu pour produire les deux types de boulettes avec deux circuits d&apos;agglomération installes en parallèle. La production de concentré enrichi (68% Fe et plus) est obtenue dans une usine d&apos;enrichissement utilisant le precédé de séparation magnétique hum ide ahaute intensite (separateurs Jones). À l&apos;usine de bouletage proprement dite, on effectue Ie broyage du concentré et sa mise en boulettes sur disques; l&apos;in duration des deux types de boulettes est obtenue sur deux chaînes d&apos;agglomération Dravo dont chacune a une capacité annuelle nominale de trois millions de tonnes.

Jan 1, 1979

By R. G. Burn

"A brief outline will be given of the concept of risk and its implications with regard to investment in exploration. The relationship between risk and decisions under uncertainty will be examined as a prelude to identifying those factors which contribute to exploration risks:consideration of the effects of corporate objectives (e.g. survival, expansion, diversification) on exploration strategy and ultimately on success or failure, exploration and mining as an investment (the relationship between risk and reward) and the desired return on investment; exploration odds, funding levels, staying power, financial exposure and the concept of gambler&apos;s ruin;origins of uncertainty in exploration decision-making-man-made risks and natural hazards; the nature of introduced constraints at each exploration decision stage and their effect on the rate of success;improving the chances of success and the invest reduction of risk through sound exploration strategy, effective project generation and efficient target detection capabilities."

Jan 1, 1984

By C. Dirscherl, M. Combes

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications.INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment)"

Jan 1, 2014

By J. K. Weglo, M. U. Savich

"The measurement and evaluation of the noise emanating from an ST4A scooptram in an underground stope under a simulated work cycle, and under three conditions of after-treatment systems is covered.These include scooptram without muffler or filler (bare engine), an in-line small filter, compared to a larger-filter, and the larger filter with an in-line muffler in series with fume diluter, which were tested under three engine operating conditions-IDLE, wide open throttle (W. 0. T.), and working condition. This is load, short haul and dump operation.The results showed an attenuation of the scooptram at work of 8 to 15 dBA, 16 cm from the exhaust pipe of the machine, to 4.8 dBA at the operator&apos;s ear. Recommendations are made to increase the attenuation at the operator &apos;s ear by additional improvement in design of the fume diluter.IntroductionIn current mining operations, the diesel engine provides a safe, efficient and highly mobile source of power. In the major underground mine s in Canada the most common types of diesel equipment are load-haul-dump (LHD) machines and ore trucks. In general, there is a tendency to use high horsepower, diesel LHD machines in mines to achieve maximum productivity. The increased use of diesel-powered equipment in underground mines has shown no cause pressure levels were measured at the exhaust and outlet pipe. Also, while measuring the octave band and A-weighted sound pressure levels, the operator&apos;s position was also measured."

Jan 1, 1986

By K. Duckworth

"AbstractA new electromagnetic depth sounding technique was applied to the measurement of salt thickness above the workings in the Central Canada Potash Mine at Colonsay, Saskatchewan. The initial tests indicate that this new technique can measure salt thickness and that the technique possesses operational feature s which make it possible to monitor trends in salt thickness throughout the mine. The technique can be applied using existing equipment, but the tests do indicate the desirability of developing equipment with features specially suited to the mine environment.IntroductionTESTS were conducted in the Central Canada Potash Mine at Colonsay, Saskatchewan during 1974 and 1975 to determine if a new technique in electromagnetic depth sounding could provide a convenient means of measuring salt thickness above the workings. This new technique, which was described by Duckworth (1975), offers operational features which appear to be advantageous in this particular situation.The problem requires that soundings be made upward from the mine workings to the base of the second red shale. This shale forms an impermeable seal on top of the Prairie Evaporite. A knowledge of this salt thickness is of interest due to the need to avoid any possibility of the workings rising to cut the red shale. Another desirable objective is the detection of any disruptions of the red shale. Ideally, this should be done ahead of the workings in order that such areas of disruption may be avoided."

Jan 1, 1977

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011