Search Documents

By STEPHEN V. FORGERON

The Loch Lamond celestite properties in central Cape Breton Island were mined by Kaiser Celestite Mining Limited from 1970 until 1976. Poor market conditions in J976forced operations to cease. Kaiser holdings included the Lake Enon, MacRae and A mac prospects. A total of about 272,000 tonnes of raw celestite have been mined. Celestite deposits are situated in the Loch Lamond Basin, specifically in Lower Windsor sedimentary rocks. Of the five formations in the Lower Windsor Group, celestite is found in the upper four. Celestite in the Enon Formation occasionally replaces shale that separates stromatolitic dolomite columns; elsewhere in the formation it occurs in association with siltstone and gypsum. Jn the B2 Limestone Formation celestite fills pores or grades between limestone and gypsum. It replaces both limestone and silty limestone conglomerate in the Loch Lamond Formation; this limestone is of unusually high grade (60 to 70% SrSO,J for the area. Evidence indicates that the Uist Formation may hold important celestite reserves. Original celestite mineralization probably resulted from evaporation of seawater on mudflats or 'sabkhas'. Secondary mineralization also may have occurred. Strontium ions could have been leached from pre-existing concentrations and overlying gypsum, moved downdip in groundwater and combined with sulphate rich waters to deposit as celestite in porous B2 limestones.

Jan 1, 1984

By Alisa M. Caswell

Outline: 1. Syncrude: Who are We? 2. Energy Use at Syncrude 3. Historical Energy Focus at Syncrude 4. Case Studies for Process Variable Monitoring 5. Extraction Flood Water Temperature Management 6. Fired Heater Tuning 7. Critical Factors for Success Syncrude: Who are We? ?Syncrude is a Joint Venture Operating Company with one product: Synthetic Crude ?Production Capacity: 350 kbbls/day ?Primary Energy Sources: ??Fuel Gas + Natural Gas ?? Coke ?? Electricity ?? Diesel

May 1, 2008

By R. Maxwell

"At Opemiska Copper Mines we have, over the past four years, operated 300 cu. ft. and 700 cu. ft. flotation cells as roughers, scavengers and cleaners and found them competitive with conventional flotation cells on a cu. ft. basis on all phases of flotation.The economics are very much in favour of the large cells for the following reasons:Power consumption is 35 to 40%, of conventional machinesMaintenance cost is about 20 to 25% of conventional machinesSpace required is about 30 to 35% of conventional machinesInstallect cost is about 40%, of conventional machinesTo put the above in more concrete terms below is what we are doing at Opemiska:1. Increasing mill capacity from 2000 to 3000 T.P.D. and will use only 5Cff, of the flotation space for 3000 tons that we used for 2000 T.P.D. with conventional flotation machines.2. Will require only 10 flotation cells for 3000 tons against 85 conventional cells for 2000 tons.3. Cells will be, one 2000 cu. ft. rougher, six 700 cu. ft. scavengers (2 banks of 3 each) and one cleaning circuit using three 300 cu. ft. cells.You will note that in this 3000 ton per day plant, we are going to have only ten cells. Had we put in conventional cells for this tonnage, we would have needed 120 cells."

Jan 1, 1970

By J. Mullins

Coal was first banked by the Dominion Coal Company, Limited, in 1898, near No. 2 Colliery, the same site as is presently used for that purpose. Though today there are banks at Glace Bay, Sydney, and Sydney Mines, these notes, except when otherwise desirable, will be confined to describing the practice as developed at the No. 2 Banking Station, Glace Bay, as being typical of methods obtaining at all sites. Storing The manner in which the coal was piled is illustrated diagrammatically in the accompanying sketch. A train of coal was brought on the main trestle, which extended the full length of the banking ground at a height of 22 to 39 feet above the natural surface, and dumped into bins which were integral with the trestle work. Chutes from these bins permitted the coal to be fed into 3-ton cars, which were horse drawn laterally on narrow gauge tracks laid about 10 ft. centres, to a maximum distance of 400ft. from the trestle. These cars were end-dump and as the pile extended laterally the narrow gauge tracks were lengthened by shorter or longer filling pieces, so that their ends were always kept at the brow of the bank. Much coal, however, had to be dumped directly on the tracks and hand trimmed to fill the valleys, and level off, between the tracks.

Jan 1, 1931

By J. Vanderlaan

A proposed method of applying high-speed, non-destructive part scanning technologies to the production process of UO2 (Uranium Dioxide) fuel pellets is presented. The scanning process examines each pellet individually for correct surface roughness and any surface imperfection or defects. Using optical scanning methods, which consist of laser and CCD camera technology, the complete circumferential surface of the pellet is examined to meet the reactor fuel bundle specifications.

Aug 1, 2010

By Yuwang Wang, Yanggeng Tan, Kezhang Qin, Zengqian Hou

Abstract- The large Derni Cu-Co (-Zn) deposit in Qinghai Province exhibits unusual geological features, and its genesis is controversial. Based on previous research and detailed field investigations, petrographic studies of the host volcanic rocks, isotope and trace element geochemistry of the sulfide ore, and comparison with typical ore deposits, this deposit is a VHMS (submarine volcanichosted massive sulfide deposit) type. This argues against previous interpretations of a magmatic or a hydrothermal replacement origin. Systematic rock, mineral and geochemical studies of the host serpentinites of the ore district indicate that the protoliths of several types of serpentinites that are widespread in the ore district are mainly ultramafic volcanic rocks. The mineralization formed within an ultramafic volcanic breccia, or between the breccia and its overlying Mg-rich carbonate rocks and volcanic sedimentary rocks. The ore-forming components were derived mainly from ultramafic rocks and partly from mafic rocks. The ultramafic rocks are MgO-rich, CaO-poor with a high MgO/FeO ratio, and the mafic rocks are rich in Na2O and poor in K2O. The chemical composition of the ultramafic rocks is similar to that of volcanic peridotite, or komatiite. The volcanic rocks that host the Derni deposit are among the most basic host rocks known for VHMS deposits, and the Derni deposit represents the most basic member in the VHMS deposit spectrum.

Jan 1, 2000

By P. C. Lightfoot, J. M. Duke, A. J. Naldrett

"The segregation of magmatic sulphides from mafic and ultramafic silicate magmas, in many circumstances, leaves the magma with a lower-than-normal Ni/MgO ratio, which is characteristic of both lavas erupted from the magma chamber and olivine crystallizing within it. Two end members of the segregation process are discussed; i) batch segregation and ii) fractional segregation.In the former, the critical factor is the magma/sulphide ratio. Computer modelling suggests that where this ratio has been less than 1000, the magma will be recognizable as anomalously low in Ni, due to sulphide segregation, and thus a good target for exploration. In fractional segregation, the critical factors are the proportion of sulphide to silicate being segregated and the degree of fractionation.Samples believed to represent the liquid portion of komatiitic lava f lows from a series of unmineralized sequences in the Abitibi greenstone belt, Canada. Belingwe belt, Zimbabwe, and Barberton Mountainland, South Africa coincide with the sulphide-free fractionation model. They are in marked contrast to samples from the ore-bearing districts of Kambalda and Scotia. Western Australia in which distinct Ni depletion, corresponding to fractionation of olivine plus sulphide in a ratio of between 100 and 200:1 is recognizable. Ni-depleted olivines also mark the sulphide-bearing Dumont intrusion of the Abitibi belt.The Moxie intrusion of northern Maine has distinctly Nidepleted olivines, as does the nearby and petrologically related Katahdin body. In both of these intrusions, the composition of the olivine allows reasonable predictions to be made of the Ni tenors of sulphide showings within them. At Katahdin, the Ni depletion is so widespread that little hope is help out for the presence of economic concentrations of sulphide. At Moxie. the olivine compositions suggest that the best chance of economic sulphides lies in the southern lobe of the intrusion.Ni-depleted olivines also characterize certain rock units within intrusions of the Insizwa complex, Transkei, Southern Africa. Many millions of tonnes of Ni have apparently been removed by sulphides from these rock units, many more than are contained within the single mineralized occurrence so far identified at Waterfall Gorge."

Jan 1, 1984

By G. Mihaylov

The basic principles of systems analysis are presented. A model has been designed to determine the location of the Main opening in the presence of three or more stock orebodies. The necessary condition is to find a location for the Collection point which is an essential element in opening up each orebody (stock). The model takes into account the total transportation costs from each orebody to the collection point. Three variants are considered provided that the orefield is divided into two levels at least: - a collection point is designed at every level; - a collection point is designed at the lowest level, i.e. where the so-called concentration level is formed; - the collection point is located at a point between the planes of the two levels; The effect of the depth of mining and mine output on determining the method of opening up the orefield has been analyzed by considering a vertical and/or an inclined shaft. A function has been constructed which allows for investigating in both a static and dynamic regime the capital costs for constructing the whole complex including the shaft. The character of the function does not allow finding the global limits. Therefore, it is of particular importance to specify the limiting conditions. In this case these are the flow capacity of development openings and the shaft. The basic groups of cost and natural indicators for assessing and selecting an optimal technological solution have been systematized. The combined analysis of the two approaches to finding the location of the Main opening and determining the mining method enables us to determine when an inclined shaft is best, and the depth at which opening by a vertical shaft has no alternative. Thus, a transition area is formed for which the selection of an optimal technological solution requires an analysis similar to that proposed in this paper. Conclusions are finally drawn which serve as a basis for determining the areas of application of each opening, including the use of a combined scheme of mine opening. The approach presented can be used in both investigating the possibilities for opening up new orefields and reconstructing existing ones in cases when the mining operations go deeper.

Aug 1, 2013

By P. W. Udo Graefe

"An interactive computer model of a dragline, windrow and spoil pile has been developed for modelling oil sands mining operations. The model is to be used in conj unction with models of other oil sands mining equipment, such as bucket-wheel excavators and reclaimers, conveyors, hoppers, bins, trucks and shovels, to study mining operations on a minute-by-minute basis. From the orebody description and mining selectivity, layers of ore and reject are determined and mined by the dragline. Reject is dumped on the pit floor; ore is either dumped on a windrow for later removal by a bucket-wheel reclaimer or directly dumped into a hopper feeding a conveyor. The model allows for the presence of pads as a dragline base, key cuts and a number of interruptions to the mining operation such as shift changes, boom checks, engineering services, repairs, delays, preventative maintenance, etc. A CRT display keeps the model operator informed about equipment status and performance. The model operator can direct the course of the simulation by issuing commands to the model at any time during the simulation.IntroductionThis paper describes an interactive computer model of a dragline, windrow and spoil pile. The model was designed by the author based on information and specifications provided by Canstar Oil Sands Ltd. The model design was implemented and tested on Petro-Canda's IBM computer system by DMR and Associates Ltd. of Calgary, Alberta.The model was designed to form three components of an oil sands mining operations model, described in reference I. Figure 1 shows the interaction of those components with the remainder of the oil sands mining model.An ""Ore/Waste Body"" data base provides information to the dragline model about the location and composition of or e and waste in the mine. The dragline model is used to simulate mining this ore/waste body, to build up spoil piles for center reject (waste) and to dump ore onto windrows or hoppers (situated over conveyors) to deliver the ore to the extraction plant. The windrow model component provides a data base which will be used by a model of a bucket-wheel reclaimer which simulates the loading of ore from the windrow on to a conveyor via a bridge."

Jan 1, 1982

By S. S. Rahman, A. Gholami, M. A. Aghighi

"This paper provides a foundation for studying the growth of fractures in presence of other discontinuities and different anisotropies of low permeable hydrocarbon formations and helps to improve the design strategies for multistage fracturing.The multistage fracturing technology has recently been used to exploit low permeable hydrocarbon reservoirs. However, the mechanism of hydraulic fractures interaction and the impact of local heterogeneities on ultimate trajectory of the growing hydraulic fractures are not yet understood in depth. A fully coupled poroelastic Finite Element based model is developed to investigate the mixed mode propagation behaviour of growing hydraulic fractures. This model takes advantage of an explicit representation of the fracture which enables us to take the effects of rock and fluid related parameters into account. Moreover, impact of fracture geometry and leak-off phenomenon is investigated. The refined mesh around the crack provides the added advantage of more detailed stress distribution, pore pressure change and back stress in the vicinity of the fracture and in particular at the fracture tip. The potential deviation propensity of the fractures is evaluated based on the fundamental rule that fractures propagate perpendicular to the direction of the minimum horizontal stress.This study shows that pressurization of transverse hydraulic fractures results in the reorientation of local principal stresses, particularly in vicinity of fracture tips. Variation of flow patterns clearly influences the evolution of shear stress around the fracture tips which will potentially lead to mixed-mode I and II fracturing and consequently, fracture deviation. The presence of local heterogeneities such as preexisting fissures and/or fractures is a main source of such pore pressure induced stress redistribution and reorientation and potential deviation of hydraulic fractures.Most existing models ignore or simplify the effect of pore pressure/stress coupling as well as the fracture geometry and fluid flow within the fracture. Also, the fluid leak-off from the hydraulic fracture into the formation, which is a controlling factor in fracture growth, is often considered using analytical models. Taking advantage of a fully coupled porelastic model along with an explicitly discretized fracture, this study provides a more realistic insight into the complex fracture propagation processes of multistage fracturing operations particularly in presence of reservoir geo-mechanical complexities."

Jan 1, 2015

By E. Goodwin

"Maclaren Forest Products Inc.Lime is commonly used for the neutralization of acid, and the removal of heavy metals in mine waste waters. However, the precipitation of heavy metals as hydroxides must take place under conditions of controlled pH, to produce minimum concentrations of dissolved metals. An account is presented explaining the concepts applied to lime-treatment processes at Bell Mine during the period of a supernatant discharge to Babine Lake; October 18, 1982to January 25, 1983. IntroductionBell Mine of Maclaren Forest Products Inc., Babine Mining Division, an open-pit copper mine, is located on Newman Peninsula, Babine Lake approximately 65 kilometres northeast of the town of Smithers, British Columbia (Fig. 1).A depressed market for copper metal in 1982 forced a management decision to suspend operations at the mine for an indefinite period from October 3 I, 1982. For some time prior to the mine closing date, mine management was concerned about the increasing level of supernatant in the tailings pond , and its possible effects on the stability of the dam when cycloning of mill tailings ceased. Consideration of these potential hazards led to an application being filed with the Provincial Waste Management for a permit to discharge the excess water to Babine Lake. This large lake, an important link with several significant salmon spawning sites, is a major contributor to the British Columbia commercial fishing industry. Jurisdiction for the environmental affairs in the area is shared by the Department of Fisheries and Oceans, the Environmental Protection Service, and the Provincial Waste Management Branch. These agencies were directly concerned in the formulation of discharge permit following joint consultation, and exchange of information with the company on environmental concerns. An approval was finally granted to discharge approximately 1,000,000 cubic metres of supernatant from the tailings impoundment at Bell Mine into Hagan Arm, Babine Lake from October 18, 1982 with a daily discharge not to exceed 9000 cubic metres. Provisions were made that a particular discharge procedure be followed, and that the company would be responsible for setting up a sampling and monitoring program to safeguard the quality of the effluent."

Jan 1, 1986

By J. Elbrond

"This paper describes qualitatively the progressive are losses and rock dilution in a mining project from the geological modelling to and including the concentration. A simple theoretical model of the net present value of a deposit, assuming a log-normal grade frequency function, is used to find the pair of decisions on rate of production and cut-off grade, which maximizes the net present value. Various degrees of ore losses and rock dilution are then applied on this optimum, and the resulting decreasing net present values are calculated, as well as the increasing cost of metal and the increasing metal losses as a function of are losses and rock dilution.IntroductionDue to a variety of uncertainties, to inevitable lack of precision in deposit estimation and in mine planning, and due to production constraints, ore losses and rock dilution occur throughout the many phases of a mining project. The phases range from the geological definition of the orebody, over the cut-off grade optimization and decision, over the design of the mining method and the actual mining to the ore dressing, where the final loss of valuable ore into the tailings occurs. Quantification of ore losses and rock dilution are mostly difficult if not simply impossible to obtain. At the end-phase an estimate of the total dilution may be obtained with some degree of precision by observations of the amounts and analysis of concentrate and tailings. It is much more difficult to estimate the total ore losses because the uncertainty of the geological modelling in the initial phase and in the mining phase is very difficult to quantify, despite the use of geostatistics for grade estimation.Many attempts at quantification of ore losses and rock dilution have been made and some examples are shown in Table I. Although they differ widely from each other, it is obvious from these figures that ore losses and rock dilution are significant and have considerable effects on the economical results of a mining operation. Life length, net present value, cost of producing metal and the loss of metal are all affected."

Jan 1, 1994

By C. Chapman, P. Cowx

"INTRODUCTIONTetronics Research and Development Co. Limited has installed several plasma torches for steel heating in continuous caster tundishes. An extensive demonstration program on a 14 tonne tundish reported the following advantages of plasma heating.• close control of steel temperature to ± 5°C;• a reduction of the furnace tapping temperature of up to 20ºC, leading to savings in energy and refractories costs ;• improvement in steel quality, to produce a slab product with an equi-axed crystal structure and a reduced number of large sub-surface slag inclusions;• the virtual elimination of oxygen pickup in the tundish; and• the capability of making ferroalloy trim additions to the tundish to permit a change of steel grade during casting, greatly decreasing inventory costs.The Need for Tundish HeatingIn the continuous casting of steel, the function of the tundish is to transfer the molten metal between the ladle to one or more continuously fed casting moulds. Figure I shows a typical temperature profile of molten steel in the tundish over the first cast cycle. It is observed that a rapid drop in temperature occurs both at the start of the cast, due to the tundish refractories absorbing heat, and also during ladle changeover. In addition, as a result of thermal losses through the ladle sidewalls, there is a gradual decline in the bulk steel temperature over the entire heat cycle. Consequently, in normal tundish operation, it is necessary to cast with a high superheat (25°C to 30°C + above steel liquidus temperature) in order to prevent freeze-up of the strand. Problems of high temperature variation and the potential of the steel solidifying in the tundish are greater for small caster units of low thermal mass . A high steel superheat increases the steelmaking vessel process time and refractory wear and prevents the formation of a uniform equi-axed solidification structure in the cast steel, resulting in centre line segregation and porosity. The large drop in the casting temperature that occurs during unsteady state operation causes an increase in the number of sub-surface inclusions, reducing the value of the product. Accordingly, plasma heating may be employed to maintain the molten steel at an optimum temperature to produce a slab of consistent quality."

Jan 1, 1989

By A. J. Williams

"Whenever a decision is made to bring a mineral deposit into production, the Owner in actual fact has decided to convert substantial sums of capital into productive capacity with the intenti6n of making a profit from such conversion.Escalating costs of construction, frustrating and costly delays in comp1etion, the increasing tempo of technological change and the increasing size and complexity of mineral processing projects have convinced Owners that the best way of implementing their capital must be sought and utilized. This requirement has stimulated a search for ways and means of applying modern management techniques to the design and construction of mineral processing plants.This search by consulting firms has resulted in the evolution of the concept of project management and the development of planning and con trolling techniques with the result that Owners can seek and obtain better assurance that their project objectives will be fulfilled.This paper will attempt to outline how a mineral processing plant can be brought into production through the implementation of project management techniques.Definition And Objectives Of Project ManagementThe design and construction of mineral processing plants is subject to the restraints of three inter-related parameters -Quality, Cost and Time each of which influences and is influenced by the other two.Project management is a technique where the Owner delegates complete responsibility to a single organization for all phases of a project (design, procurement, construction and commissioning) for the above parameters but retains freedom for major decision making. Normally, the consultant under-takes full responsibility for all phases, but partial project management services can be provided when the Owner so desires.The objective of project management is first to devise and define and then to implement a program in which the relationship between the three parameters of Quality, Cost and Time is optimized, i.e., the desired functional and other requirements are attained (but not exceeded) at the lowest practicable overall cost in the shortest practicable time. The measure of success of a project lies in the degree to which this objective is achieved."

Jan 1, 1974

By H. M. Howard

"The subject of Grinding Media is perhaps still quite controversial. Many people will state today that the spherical ball is the only way, and also will state that this was settled long ago others are not so sure, and I am in this second category. Over the years there have been many changes in grinding and in our evaluation of grinding media we should always be ready to review the overall situation at regular intervals. There is quite a lot of inertia in all branches of Hineral Dressing and this is particularly true of grinding or, more correctly, comminution.In order to understand some of the things which are done today, and to understand some of the thinking on grinding, it is desirable to go back some sixty years and trace the developments in comminution. In doing this we should consider perhaps three general categories with respect to daily tonnage. An arbitrary division would be under 500 T.P.D., 500-5000 T.P.D., and large operations which might have several parallel units, each with a capacity of about 5000 T.P.D. For the future, in the broad picture, this last category will be the important one because we will be more and more dependent on large-tonnage low-grade operations for most of the metals of the future. Some such division is necessary because the daily tonnage will have a very great effect on what we can and cannot do. It is also necessary to consider the entire flowsheet, and to remember in particular that grinding is not merely to make small particles but is also a conditioning process, to prepare the materi.al for the process which follows. The relationship of crushing to grinding must also be considered. It is logical to include the liners as part of the grinding media and we should try to distinguish between the wear of grinding media and the consumption of media by corrosion. Finally, the whole question of grinding media should be examined in relation to the possibilities of using some form of autogenous grinding."

Jan 1, 1970

By D. L. Mckay

"Texasgulf's 25-foot-diameter Kidd Creek No. 2 Shaft is situated next to the company's No .1 Shaft, so that both shafts can share common surface and underground facilities. Shaft construction, covering a span of five years from collaring to commissioning , started by freezing the 50 feet of grey varved clay covering the bedrock. After first completing the concrete headframe, sinking to the 5/00-foot horizon utilized two different shaft construction methods. The top 2800 feet was excavated by slashing a 6-foot-diameter borehole and hoisting the broken material up the 3OO0-foot-deep No.1 Shaft; the remaining 2300 feet was excavated by conventional benching methods. Prior to installing the 5100 tons of galvanized shaft steel on the completion of the sinking operation, the sinker was able to install all thirteen armoured electrical cables in one pass with his modified galloway stage. All loading and lip pockets were installed along with the steel guides and bun tons during the equipping operation.IntroductionOn November 21,1978, Texasgulf completed the No.2 Shaft at Kidd Creek Mine. This shaft is the largest shaft (volumewise) in North America and is unique in many respects . The purpose of this paper is to outline some of the unique features of this shaft as well as to record how this facility was constructed.Soon after sinking No.1 Shaft, Texasgulf started a program of exploratory diamond drilling from the 2800 level in No. 1 Mine. The drilling outlined sufficient ore below that level to justify a second mine. Feasibility studies demonstrated that production could be increased by one-third exclusively from this deep ore . The study called for a 25-foot-diameter shaft to the 5100-foot horizon to service a mine producing 5,000 tons of ore per working day.The site chosen for No.2 Shaft and head frame is 350 feet southwest of No.1 Shaft. This, along with No.1 Shaft, will be away from the influence of ground subsidence when mining at depth. The collar and head frame foundations are located on a flat rock ledge some 70 feet below surface. This flat ledge was found by test holing through the overburden by diamond drilling. It is fortunate that this location best satisfied the surface layout and logistics for both surface and underground ore and waste handling."

Jan 1, 1981

By J. F. K. Brown

MR. T. L. McCALL: Planning ahead in coal-mining is essential, but the question may be raised, just how far ahead can we plan. You can overdo it: chat is, you can get in a rut. Never let planning get a hold on you to chat extent. You must be prepared to deal intelligently with any new conditions that arise, and to apply new discoveries. It may become necessary to abandon ? .your plan, make the best you can of the ground you have developed, and start again, with a new plan. So far as the submarine workings of the Dominion Steel and Coal Company are concerned, we cannot know definitely what lies ahead of us under the sea: we must ?base our tentative plans on assumptions, and, as we meet changing conditions, we must change our plans. In the case of inland mines it is possible to bore in advance, and consequently it is generally possible to set out your plans in advance, block out a section of the mine, and develop to obtain a uniform product for a whole year, or perhaps even longer. MR. J. B. MORROW: While planning in coal mining, we must bear in mind chat the consumer also is planning ahead. Some people will tell you that, in ten years time, the demand is going to be all for pulverized co al; others believe that the field for such fuel is limited. Needless to state, planning for a pulverized-coal market is quite a different matter to planning for a general grade, ore stoker, market. In planning, therefore, our endeavour must be to keep a jump ahead of the work being undertaken by the anthracite producers. This year, they are spending about two million dollars-money contributed, not by the Government, but by the industry itself-in the study and promotion of new and improved ways of burning anthracite. For example, they are perfecting small hot-water heaters, and one they have brought out weighs only about ten pounds. I feel that research of this type must be regarded as an essential part of planning in coal mining. We, in the soft-coal industry, are also planning types of more efficient burning equipment and doing other investigational work.

Jan 1, 1937

By Nural Kuyucak, Bohumil Volesky

"Extensive screening revealed a seaweed (alga) biomass type which in its non-living state possesses a very high cobalt sequestering capacity comparable to that of activated carbon and the ion-exchange resin currently used in the cobalt production process. Performance of the new bio-sorbent material was studied by examining its equilibrium metal uptake isotherms generated under different solution conditions such as initial cobalt concentration pH, temperature, and the presence of selected cations and anions. The rate of cobalt uptake was determined, which is a crucial parameter for recovery process design. Almost all cobalt sorbed can also be desorbed with a solution of CaCI2. The bio-sorbent material can be used repeatedly in the sorption-desorption cobalt concentration process. IntroductionIt has been well documented that certain types of microbial biomass, living or non-living, possess a high potential to sequester and accumulate inorganic ions present in aqueous solutions. Metal concentration by microbial biomass from a solution is termed bio-sorption. This phenomenon is quite complex and includes adsorption of metals onto the surface of a microorganism and/or into the cellular structure in combination with ion-exchange, complexation, and/or micro-precipitation. Bio-sorption is generally considered to be a rapid physical/chemical process. The cell wall structure is porous and allows metal ions, as well as large organic nutrient molecules, to pass freely through. Polysaccharides of the cell wall could provide binding amino, carboxyl, phosphate and sulphate groups. In addition to these functional binding groups, polysaccharides often have ion-exchange properties. Sometimes, bivalent cations, such as Ca2+ or Mg2+, help the formation of ionic bond bridges between the negatively charged cell surfaces and positively charged cations in the solution, Proteins in the cell wall could offer functional groups and also offer peptide bonds to bind ions. Interactions between metal and the cell wall components are responsible for the sequestering of metals by way of bio-sorption. Many metals feature a complex solution chemistry and it is not always possible to determine what ionic species are actually present in the solution. The equilibria involved are dependent on pH, concentration, the anions present and other factors. The transport system for the ions are sometimes dependent on both temperature and energy. Biosorbent material could also be regenerated for multiple reuse."

Jan 1, 1988

By Laxman M. Amaratunga

"The fine fraction of tailings is usually excluded from the backfill process and generally disposed on the surface in tailings ponds. Because of the ever increasing demand for fine grinding in the extraction process for improved liberation of valuables in the ore, increased production of fines in the tailings has resulted. The negative impact of surface impoundment of tailings on the environment is well known. Amaratunga and Annor (1989) first presented a concept of fine tailings agglomeration for backfill.This paper presents the development of the novel cold-bond tailings agglomeration (CBTA) technology for non-reactive fine gold mill tailings. For cold-bond agglomeration regular portland cement was used as a binder. In order to cut costs, alternate binders such as lime, and blast furnace slag cement were examined. The effects of binder dosage, curing time, and agglomerate size on the fracture load strength of the agglomerate were studied.Fine tailings agglomerates are mixed with coarse tailings or non-agglomerated fine tailings to make high density fill compositions to be used as underground backfill. Alternatively, the agglomerates can be used as aggregates for surface applications. The paper discusses the environmental and operational benefits of this total tailings utilization and disposal technology.IntroductionIn Canadian mines, mill tailings are probably the most commonly used material for backfill. However, only the coarse fraction of tailings is desirable for use as hydraulic fill or high density fills. The fines are disposed on the surface in tailings ponds since they are unsuitable for underground backfilling owing to the following factors:i) slow settling ratesii) longer percolation timeiii) excessive consumption of binder due to drainageiv) poor compactionFor improved value liberation more milling operations have resolved to fine grinding in their comminution circuits. Gold milling operations driven by down stream leaching processes grind their ores excessively fine. In general, gold mines use hardly any tailings for backfilling. This can result in periodic short falls and the need to search for alternate backfill material from other sources. Apparently, the gold producers are the most identifiable sector which suffer from a shortage of backfill materials ( Amaratunga and Annor, 1989)."

Jan 1, 1994

By A. Miura, R. Winarko, D. B. Dreisinger

Chalcopyrite leaching in acidic ferric sulfate media at ambient temperature exhibits slow kinetics and poor leaching efficiency, which is typically attributed to surface passivation. Recently, the presence of small amounts of iodide in the leaching media has been reported to significantly accelerate chalcopyrite dissolution. To further explore the behavior of chalcopyrite leaching in the presence of iodide, it is essential to determine the factors that control the leaching kinetics. In this study, we investigated the effect of initial solution potential, iodide concentration, particle size, and temperature on the kinetics of copper extraction from chalcopyrite. The key in the experimental setup was to minimize iodide loss by iodine evaporation and precipitation as cuprous iodide. The former was achieved by performing the leaching tests in fully sealed leaching systems. The latter was achieved by maintaining the solution potential higher than 420 mV (versus Ag/AgCl electrode), where formation of CuI precipitate is possible. The experimental results show that higher solution potential and higher iodide concentration had a pronounced positive effect on the rate of chalcopyrite dissolution. There was no effect associated with particle size, which might be due to the narrow size range tested. The positive effect of increasing temperature only manifested itself when the solution potential was sufficiently high. INTRODUCTION The main challenge of chalcopyrite leaching using ferric ions as the oxidant at ambient temperature is the slow kinetics and poor extraction. The reason for this leaching behavior has been attributed to passivation resulting from formation of insoluble passivating layers on chalcopyrite surfaces, which could be metal-deficient sulfides, elemental sulfur, polysulfides, and iron precipitates (Klauber, 2008). To overcome passivation, technologies using higher temperature and pressure have been developed to leach chalcopyrite concentrates, such as the CESL process (Mayhew, McCoy, Mean, & Woeller, 2013), FLSmidth Rapid Oxidative Leach (ROL) process (Mulligan et al., 2017), Galvanox (Dixon, Mayne, & Baxter, 2008), Albion process (Hourn, Turner, & Hourn, 2012), HydroCopper (Hyvärinen & Hämäläinen, 2005), TPOX (Dreisinger, 2006), and AAC/UBC process (Dreisinger, Dempsey, Steyl, Sole, & Gnoinski, 2003). Even though they are effective in accelerating copper leaching kinetics, those technologies typically have higher capital and operating costs associated with production of concentrates and application of autoclaves. This makes them unsuitable for treating low grade primary copper sulfide ores.

Jan 1, 2019