Search Documents

By Ron Bradburn, Derek Perkins

"The Brenda mine is located in south central British Columbia, 22 km north west of Peachland, in the heart of the Okanagan Valley. Situated at an elevation of 1500 metres, the mine area straddles the divide between the headwaters of Trepanier Creek and Peachland Creek. These flow into Okanagan Lake, the chief valley water resource located 1100 metres below. The creeks are of great significance to the water management of the area as they constitute the water supply for the Municipality of Peachland, a thriving retirement community with a population of 5000. A location map is shown in Figure 1.The history of the Brenda Mine operation has been well documented previously. After twenty years of operation, the open pit mine shut down in June 1990 due to the depletion of its ore reserves. During the course of its life, it produced 109 million tonnes of waste rock which is thought to contain approximately 0.10% copper as chalcopyrite and 0.015% molybdenum as molybdenite stored in four rock piles around the pit. Similarly, approximately 200 million tonnes of tailings were produced grading 0.015% copper and 0.005% molybdenum. During operation, tailings were hydrocycloned to produce a coarse sand for dam building with the fine slime stored behind the dam. It is estimated that 40% of the tailings were used for the dam construction. The layout of the mine site is shown in Figure 2.The mine was operated under a zero discharge permit. This was achieved by diverting practically all surface water flowing towards the mine area around the site. Water affected by mine operations, was discharged to the tailings impoundment, and recycled to the mill for reuse. The recycle rate was 90% and seepage from the tailings embankment and saddle dam was pumped back to the tailings pond. Because acid drainage was not a problem with the low grade Brenda rock, runoff from the rockpiles was initially released to the local environment. However, due to the alkaline nature of the waste rock, dissolution of low concentrations of molybdenum in the site runoff waters became evident by the late 1970's. The molybdenum content of Peachland Lake, the water reservoir for the municipality of Peachland, approached the Canadian Drinking Water Standard of 0.25 ppm. By 1979, a series of diversion and collection ditches was completed to direct all runoff water from the rockpiles to the tailings impoundment area. This had a significant detrimental effect on the site water balance causing it to go into a considerable surplus condition. During normal operation, this oversupply was contained by the rate of tailings dam building. An economic shutdown of the mine during 1984 forced a limited discharge from the site to protect the integrity of the tailings dam."

Jan 1, 1995

By Tom Shumka

INTRODUCTION ?The Electro-Magnetic Crack Detection (EMCD) technique is an electromagnetic inspection method used for detecting and sizing surface breaking flaws. ?It works well on structural material or welds, ferrous or non-ferrous metals. ?EMCD?s rapid scanning is achieved using a hand-held probe. ?EMCD provides reliable crack detection and sizing (length and depth). Cracks can be sized accurately. ?EMCD dramatically reduces most cleaning requirements as there is no need to clean to bare metal. ?EMCD is capable of inspection through thin metallic coatings, or through non-conducting coatings up to 10mm thick. ?EMCD allows full data storage for back-up, off-line view and audit purposes.

Oct 1, 2010

By Jiachen Wang

Longwall top-coal caving mining is one of the major mining methods for extracting thick coal seams in China. The top-coal caving longwall mining was began to use in the 1980s in China, and got the rapid development. The development of the top-coal caving mining technology in China, the achievements and the theoretical aspects progress of this method are described in detail in this paper. And the main technical model of China's top-coal caving mining is introduced in this paper. This paper also introduces the application of large-cutting-height mining in China and the technical level it has reached.

Aug 1, 2013

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By Robert Voisey, Robert J. Spencer

"LynnGold's MacLellan Mine is located about 8 km south east of Lynn Lake immediately to the east of the Keewatin River (Fig. I). The property is accessible by an all-weather road, leading north from the provincial highway 391, which links with the Town of Leaf Rapids and the City of Thompson to the south.The ore body, as outlined in the original feasibility study, is expected to produce in excess of 9.3 x IQ6 gm of gold and silver over the next 5 years. However, the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan Mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 48 km west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan Mine or relocated to Sherrin's Ruttan Operation.GeologyThe MacLellan gold ore deposit is located on the northern section of the Lynn Lake Greenstone Belt known as the Rainbow Trend. This Trend is a 40 km gold bearing rock sequence extending both east and west from the MacLellan Mine. The southern section of these two east-west trending structures is known as the Johnson Shear, this is also gold bearing."

Jan 1, 1990

By Pascal Lesagel

Life Cycle Assessment (LCA) is a holistic environmental assessment tool that allows the compilation and evaluation of the inputs, outputs, and potential environmental impacts of a product or service throughout its life cycle, from cradle to grave (i.e., from resource extraction and transformation to final disposal, including production and use stages). The relevance of LCA for the mining industry is twofold. First, the mining industry has a role in providing the LCA community the data that allows subsequent evaluations of the life cycle environmental impacts of primary materials such as metals, as well as the environmental comparison of the downstream products of the mining industry with other competing materials for specific uses. Second, the mining industry can use LCA in order to evaluate the environmental impacts of its activities, identify their environmental hotspots and compare the impacts of available technical options. For example, the environmental impacts of different extractive and processing technology can be compared through the use of LCA. This latter use of LCA by the mining industry is less common. This paper discusses the use of LCA to compare sulphidic tailings management options. The paper also presents some of the LCA research challenges that still have to be addressed to increase the relevance of LCA results for the specific context of mining activities.

Nov 1, 2008

By P. Keller, T. E. Lister, G. G. Clark, L. A. Diaz

As electronic technology continues to evolve there is a growing need to develop processes which recover valuable material from antiquated technology. This need follows from the environmental challenges associated with the recovery of raw materials and fast growing generation of electronic waste. Although present in small quantities in electronic devices, the availability of raw materials such as rare earths and precious metals becomes critical for the production of high tech electronic devices and the development of green technologies (i.e. wind turbines, electric motors, and solar panels). Therefore, the proper recycling and processing of electronic waste presents an opportunity to stabilize the market of critical materials, providing a proper disposal and treatment of a hazardous waste stream. This paper describes the development and techno-economic assessment of a comprehensive process for the recovery of value and critical materials from electronic waste. This hydrometallurgical scheme aims to selectively recover several value streams (base metals, precious metals, and rare earths) present in electronic waste. The economic feasibility for the recovery of rare earths from electronic waste is mostly driven by the efficient recovery of precious metals, such as Au and Pd (ca. 80 % of the total recoverable value). Rare earth elements contained in magnets (speakers, vibrators, and hard disk storage) can be recovered as a mixture of rare earth oxides which can later be reduced to the production of new magnets.

Jan 1, 2016

By Nima Nabavi

Shovels and excavators have significant blind spots due to their large sizes, increasing the chances of collision with other surrounding equipment such as haul trucks, loaders, and dozers. While a camera surveillance system is very useful in preventing collision, it can benefit from two additional features: (i) the ability to display the distance of the closest object within the view, and more importantly (ii) the ability to warn the operator if objects are getting too close. After a comparison between few different technologies, it is explained how these features can be provided by integrating rugged pulsar radar sensors with a camera system. The specific radar technology is already field proven in the harsh mining environments. Motion Metrics International Corp. has developed this exact product, which combines its 4-camera surveillance system (ViewMetricsTM) with a series of rugged radar sensor elements, named ViewMetricsTM-Radar. The radar system employs intelligent CAN bus communication to reduce wiring, hence improving hardware reliability with built-in troubleshooting features. A USB connection is the only hardware bridge between the radar sensors and the embedded computer. As such, an existing ViewMetricsTM system can be easily upgraded to ViewMetricsTM-Radar. As addition of new interfaces to the cab could result in operator distraction, this paper explains how ViewMetricsTM-Radar reduces distraction compared to other radar collision prevention systems.

Oct 1, 2009

By V. C. Wittchen, T. R. Yu, J. E. Croxall

"The consolidated rockfill at Kidd Creek Mines is a weakly cemented, minus 15 cm aggregate which posed problems for conventional drill/blast drifting methods. Consequently, lateral access to mineable ore adjacent to backfilled areas was gained by drifting around the fill in shattered rock.In mid-1987, Kidd Creek Mines began to investigate means of mechanically excavating drifts in backfill . The results of this investigation led to a trial program using a Dosco MK-2A Roadheader to excavate the required drifts in backfill.The roadheader was tested at Kidd Creek Mines from July to November 1988, in 28-735 X /C to be used as the top access for drilling and blasting 32-74/ ST. During this period, the roadheader excavated 54 m of a 4.3 m by 3. 7 m arched drift in backfill. Cutting rates over the period averaged 0.8 m/cutting hour as projected with a daily high of 2.0 m/cutting hour.Wood-lagged 2-piece steel arches on 1.2 m centres were chosen as ground support for the trial. Shotcrete will be tested in a roadheader drive for its potential to improve productivity by replacing the steel arches.The trial program included evaluations of point-attack picks, two sizes of cutter motor, 20 MPa (3000 psi) water-assisted cutting, cuttings-removal systems, and environmental control devices."

Jan 1, 1990

By Moatassem Abdallah

Buildings in the United States account for 72% of electricity consumption, 40% of energy consumption, 13% of water consumption, 39% of carbon footprint, and 30% of waste output. In order to minimize these negative environmental impacts, many public and private owners are requesting that their buildings be more sustainable and certified under the widely known programs such as leadership in energy and environmental design for existing buildings (LEED-EB). To accomplish this, buildings are increasingly integrating green building measures including energy efficient lighting, motion sensors, thermal pane glass, geothermal heat pumps, EnergyStar rated HVAC systems, photovoltaic systems, and wind turbines. This research paper presents the development of an automated decision support system (DSS) that is designed to optimize the selection of green building measures which can be used to upgrade existing buildings. The developed DSS incorporates two optimization models that are capable of (i) minimizing the total upgrade costs required to accomplish a specified LEED-EB certification level such as silver or gold; and (ii) maximizing the number of accredited LEED-EB points within a specified budget of upgrade costs. The DSS is designed to identify a set of optimal upgrade decisions that accomplishes these two optimization objectives. An application example is used to illustrate the capabilities of the DSS and to validate its result.

Aug 1, 2013

By K. G. Chipman

The Geological Survey is the oldest map making department in the Canadian Government service, and when organized in 1842, one of the first principles to be recognized was the absolute necessity of having good maps. The primary purpose of the Survey has always been geology; but because a graphic representation by means of maps makes the written report .more readily intelligible; because the correlation of known geological facts is often difficult or nearly impossible unless they can be represented on a map; and, because the public demand information shown in this way, the Geological Survey must continue to supply maps; and the supplying of these maps must be considered as an essential part of the work of the Survey. It is a commonly recognized principle of pedagogics that an appeal to the eye is quicker than one to the ear; that children (and others) learn more quickly when a thing is presented to them through the eye rather than through the ear. The application of this principle to the work of the Geological Survey is that, to a large number of people, the message of a map is more quickly grasped, is more readily intelligible, and is in many ways of more interest and value than is the same information in a report. I do not mean that the maps are of more importance than the reports.

Jan 1, 1924

By R. B. Kaunda

One fundamental requirement for surface and underground rock engineering is the ability to characterise the rock mass. An accurate characterisation of the rock mass allows rock engineers to optimize designs safely and economically. A number of classification systems have been developed in the past 50 years to help characterise rock masses such as RMR, Q system, Rmi, and several others. The challenge in developing rock characterisation schemes is often practicality, i.e. creating systems with relatively simple inputs for the everyday practitioner. A second challenge is the degree of subjectivity often inherent in commonly used classification systems. These challenges are especially exacerbated in weak rock or densely jointed rock masses. This paper introduces a new approach to characterise densely jointed rock mass using artificial neural networks and principal component analysis, based on principles commonly used in the geotechnical engineering of rock fills and waste rock dumps. Thirteen input parameters are dimensionally compressed using principal component analysis. Using a global database with more than 100 case histories, an artificial neural network is developed to conduct the rock mass characterisation. The advantage of this approach is less subjectivity as commonly used engineering (quantitative) terms are put to use. A further advantage is that given that the method is site-data dependent, it allows for ‘fine tuning’ of the model for a specific site.

Jan 1, 2015

By A. K. Debnath

Mining being a site specific activity, land becomes the prime requirement for starting, successful execution and closure of any mining project. Many important mining projects are not progressing satisfactorily just because land is not easily available or environmental/social issues are not addressed properly. This is especially true in the case of open-pit mining, which requires large areas for mining, dumping of waste and additional land for other mine facilities. Mine closure & post mining land use exercises, though funded generously, may not achieve their objectives owing to uneven land profile after mineral extraction is over. One of the prominent solutions to these issues is application of steep angle conveyors in large open pit mines that will result in more space for internal waste dumping and enhanced slope stability of the dump. Additionally, such applications will result in economic extraction of mineral in deep open pits. Land reclamation exercise may start concurrently during early years of mine development as mineral evacuation is limited to a specific part of the mine. Surface mining facilities can also be advanced along with the pit by using modular/portable structures. The paper presented here attempts to address specific land related issues by developing suitable schemes and plans that can be practically implemented in open pit mines using advanced technology i.e. steep angle conveyors.

Aug 1, 2013

By W. D. Haley

The report of the Forestry Committee, presented to the recent Imperial Conference at London, is discouraging in its view of the future of timber resources and supplies. From a review of the forestry situation throughout the world, there is every likelihood that, thirty years from this, a shortage of the soft-woods will be severely felt. In the United States, only about one-third of the present forest area contains virgin timber. This will be cleared at the rate of five and a half million acres a year, so that in twenty-five years it will be about all gone. Canada has only about 27 per cent of her original forests left, and her virgin soft-wood will last but another half century. At the present time, the value of her lumber products is over $300,000,000 annually. During the summers of 1909 and 1910, the Government of Nova Scotia caused an examination to be made of the forest conditions in this Province. The reconnaissance, which was under the direction of Professor B. E. Fernow, of Toronto, involved an examination of the various soils, the rate of growth of the wood, and a general survey of the forest area. The importance to the Province of conserving its forest resources was clearly shown, and a number of recommendations were made, which; however, were never acted upon.

Jan 1, 1927

By Mohammad Mehdi Salarirad

Fouling of activated carbon by different organic species is a great concern in carbon in pulp and carbon in leach circuits. The rate of gold adsorption onto activated carbon from synthetic gold solutions which contained different amounts of potassium ethyl xanthate (PEX), potassium isobutyl xanthate (PIBX), and methyl isobutyl carbinol (MIBC) were evaluated through batch adsorption tests. The results of these experiments showed that the gold sorption rate rapidly decreases by increasing the concentration of collectors including PIBX and PEX up to 20 mg/L and at higher concentrations, the kinetic rate constant (i.e., k value) gradually leveled off to 53 h-1 for PIBX, which is 46% lower than the 99 h-1 for PEX. At low concentrations of up to 15 mg/L of MIBC, a gradual decrease of the rate constant was observed, while at higher concentrations, the decrease was found to be more pronounced. The gold loading capacity and the rate of gold adsorption onto activated carbon from a gold cyanidation pulp in the presence of flotation reagents were also evaluated. The results of these experiments showed that the flotation reagents have no significant effect on the gold loading capacity of activated carbon at prolong adsorption period, meanwhile the rate of gold adsorption continuously decreases by increasing the concentration of flotation reagents in the leaching solution.

Oct 1, 2011

By Larry M. Southwick

Processing of ores to recover metals usually generates large amounts of waste materials, such as rejects from concentrating operations, tailings from leaching and slags from smelting. These wastes often contain substantial amounts of iron and other metals, recovery of which are often considered to be of commercial value. Earlier versions of this paper investigated a number of processes built to recover iron from a variety of copper processing residues. This paper will extend that coverage to residues from nickel/cobalt, aluminum, asbestos and oil shale processing and coal plant fly ash. Products of interest are iron, ferroalloys, magnesium and aluminum. While none of these processes achieved long-term commercial success, their efforts cover the gamut of problems that must be addressed in treating dirty and difficult materials to recover generally low-value products. An Adept is an alchemist who can create a Philosopher's Stone, which could transmute base metals into gold. In 1701 in Berlin one Johann-Freidrich Böttger, a nineteen year old apothecary's apprentice, told King Frederick I that he could discover how to make the Stone. He failed and fled Frederick's wrath to Poland. He failed again, and King Augustus II threw him in jail. Then, in 1709, he discovered instead the secret of making Dresden china, certainly a more practical search. His failures in alchemy led to the nickname Adeptus Ineptus.

Jan 1, 2004

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

By J. M. Wetherill

"This paper presents the results of an investigation into the level of radon, as against the natural background, at the Vicary Creek coal mine in Alberta. The concentrations of radon and daughter products detected in the mine were considered to be insignificantly higher than the concentrations of naturally occurring radon and thus do not constitute a health hazard to the miners.INTRODUCTIONTHE HIGH INCIDENCE OF LUNG CANCER among miners exposed to radon was established some thirty years ago. The presence of this gas in mines is primarily associated with pitchblende extraction operations, al-though coal contains detectab`e quantities of U30s. A previous study bas shown that coal from southwestern Alberta (Exshaw and Banff) contains lower than average concentrations of this element (1).As part of a general investigation into the occupational health environment of coal miners in Alberta, field measurements were made to establish the level of radon and to investigate the natural background radiation in the Vicary Creek coal mine, located some 16 miles north of Coleman, Alberta, on the easternmost slopes of the Rocky Mountains."

Jan 1, 1968

By A. -M. Cadieux

During the geological synthesis of the Réservoir Pipmuacan area (NTS 22E) by the Ministère des Ressources naturelles (Québec), several ilmenite-apatite occurrences, some well-known and some recently discovered, have been examined. These occurrences are hosted in the Lac-Saint-Jean and Labrieville AMCG anorthositic suites. The Lac-Saint-Jean Anorthositic Suite (1160-1140 Ma), composed of multiple intrusions covering an extensive surface area, is characterized by labradorite plagioclase. The Labrieville Anorthositic Suite (1010-1008 Ma) is characterized by andesine plagioclase. It was previously known as the Labrieville Anorthosite, which was composed of a small isolated pluton located east of the Lac-Saint-Jean Anorthositic Suite. However, new geochronological data and field observations indicate that the Labrieville Anorthositic Suite in fact includes several intrusive bodies, namely the La Hache Monzonite and the Mattawa Anorthosite. A series of major structures (Saint-Fulgence, Pipmuacan, and Chute-des-Passes deformation zones) and their conjugate faults played an important role in the emplacement of the Lac-Saint-Jean Anorthositic Suite. The Saint-Fulgence deformation zone appears to have been involved in the emplacement of the Labrieville Anorthositic Suite. Oxide mineralizations are abundant in both anorthositic suites. Ilmenite, magnetite (± titaniferous), and apatite assemblages are found mostly in the labradorite-type anorthosites, while hemo-ilmenite, magnetite and apatite assemblages are associated only with the andesine-type anorthosites. Field works has revealed ilmenite-apatite mineralizations in a variety of settings, with grades reaching 48% TiO2, 16.2% P2O5, and 71.7% Fe2O3 (tot). Numerous oxide-bearing gabbronorites, often accompanied by or located near massive apatite-oxide accumulations (nelsonites), were discovered. Among these oxide-rich zones, breccia zones with anorthosite enclaves in an oxide matrix (ilmenite-magnetiteapatite) have been observed. Locally, ilmenite-apatite mineralization occurs as cumulate concentrations in ultramafic rocks. Evidence has been observed for immiscible magmas, for magmas differentiated from a mangerite or jotunite parent, and even for late magmas differentiated from the anorthosite magma itself (apatite-bearing anorthosite). Finally, the northern part of the Lac-Saint-Jean Anorthositic Suite hosts sulfide and vanadium mineralizations associated with ilmenite-apatite enriched zones, with grades reaching 1.48% Cu, 1.22% Ni, 1.6% Cr2O5, 0.25% Co, and 0.52% V2O5.

May 1, 2003

By P. Hubert, J. P. Ildefonse, F. Qafssaoui, J. Poirier

Corrosion tests by corrosive alumina-lime slags were carried out on commercial high alumina bricks used in steel ladle linings and model refractories (with different raw materials : bauxite, andalusite, and different microstructures). Using (SEM) scanning electron microscope and (EDS) energy dispersive spectroscopy, microstructures of slag-corroded refractory interfaces were studied in detail. The monomineral and glassy phases, the composition of reaction products and chemical profiles were determined. A thermochemical analysis based on phase equilibrium diagrams has permitted to estimate the proportion and the composition of the high temperature intergranular liquid phase. These data were compared to the experimental microanalysis results. The viscosity of the high temperature liquids were calculated according to Urbain 's model and the relationship between the viscosity and the penetration of liquid phases were discussed. These theorical and experimental results were used to understand the complex phenomena of slag penetration and corrosion of andalusite and bauxite refractories at high temperature and to propose new ways of improvements for the formulation of high alumina refractories.

Jan 1, 2004