Search Documents

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

By F. Kapeller, G. Herget

"The need for monitoring the effect of changes in ground stresses due to mining in hard rock has existed for many years. The Mining Research Laboratories of CANMET, EMR have developed a new tool which monitors with high precision the radial deformation in boreholes. The result is the Mining Research Laboratories strain monitoring system (MSMS) which uses the highly stable and very sensitive vibrating wire principle to monitor deformations in relatively large boreholes, e.g. 76 mm to 153 mm diameter.The vibrating wire is strung across a relatively large proving ring and operates at a frequency between 600 to 1800 Hz. The read-out system is based on continuous vibration.The ring is installed with a hydraulic tool and brought into contact with the surrounding rock through precisely machined and guided wedges. The resolution of the system is in the neighbourhood of 4 x 10-4 min/ Hz. The data collection can be carried out with a portable read-out unit and provisions are available for automatic data collection. Stresses may be calculated from strain readings.The system was tested in cooperation with the Centre de recherches minérales at the Niobec Mine in Quebec for the purpose of monitoring the effects of drill drift development and slope mining on surrounding ground stresses.After access was available to the site, 153 mm diameter holes were drilled for the determination of in situ ground stresses. These holes were then used to install the strain monitoring system. The effect of drill drift development and production blasting in stopes C-203-13 and C-203-15 on ground stress distribution could be observed clearly.The horizontal relaxation in the core of a pillar which occurred during mining of adjacent rooms was between 0.082 mm to 0.111 mm. Calculations of stresses from these deformations indicate that the rock material is still in an elastic condition.Roctest of Montreal has obtained a license on the manufacturing and distribution rights. A patent has been registered and CANMET will assist in installation of the MRL strain monitoring system and the interpretation of records."

Jan 1, 1989

By A. Ducastel, S. Connemann, A. Stark, F. Bouillot, C. Fricke-Begemann, LSA, H. Knapp, L. Horckmans

"Refractory materials are essential for all high-temperature applications in industry. Depending on the position in the furnace and specific process requirements, refractories are produced from several raw materials, such as dolomite, magnesite, bauxite, graphite or chromite. Most of these raw materials are not rare but strict quality requirements limit the producers of refractories to only a few deposits in the world. Thus, raw material supply is a critical factor for the production of refractories and accounts for 40-50 % of the total costs of refractories.A possible way to lower dependency on raw material supply is recycling of spent refractories. Main challenge in recycling is the separation of different brick types from each other and the removal of impurities, such as steel or slag. The European FP7 project REFRASORT aims to apply sensor-based sorting for separation of spent refractories. Sensor-based sorting is known from food industry, recycling and mineral processing and has proven its reliability. Nevertheless, some adjustments are necessary compared to applications in mineral processing because of other sensor-types and a higher number of products in one sorting step. This paper presents the results of feasibility tests for sensor-based sorting of refractories with near infrared spectroscopy and laser-induced breakdown spectroscopy (LIBS). Both sensors showed the potential to identify different brick types but the most promising results were obtained using LIBS technology. INTRODUCTIONRefractories are solid, ceramic products, which can sustain temperatures of more than 1500°C, without losing their stability or shape. Bricks of refractories have to withstand corrosion in contact with liquid steel or slag. Various high temperature applications, such as the production of glass, steel, copper or cement, require high quality refractories. The quality requirements of refractory bricks are strict, because small impurities can lower the thermal strength significantly."

Jan 1, 2016

By Tai Sik Lee

Why ISRU into Space Exploration are important NASA and International Mission statements calls for the sustainable human exploration of the Moon, Near-Earth asteroids, and Mars Common Exploration Goals and Objectives are Strongly influenced by ISRU Extend Human Presence: Continually increase the duration and level of self sufficiency at all destinations Develop Exploration Technologies and Capabilities: Develop and validate tools, technologies, and systems that extract, process, and utilize resource to enable exploration missions Perform Science to Support Human Exploration: Characterize available resources at destinations Stimulate Economic Expansion: Encourage commercial services and create new markets, including markets for discovered resources Enhance Earth Safety: Test techniques to mitigate the risk of asteroid collisions with Earth

May 1, 2013

By Fred E. Gray

The mill of Bralorne Mines, Limited, is located on the government highway in the Bridge River mining district of British Columbia, approximately fifty miles northeast of Shalalth, the shipping point on the P.G.E. railway. Prior to 1931, the property now owned by Bralorne Mines, Limited, was operated by Lorne Gold Mines, Limited. During the early operation of the mine, the ore had been treated at various times in one of three small amalgamation mills on the property. With the succession to ownership by the Bralorne Mines, Limited, work was started on construction of a new mill of approximately 100 tons capacity per day. The new mill was put into operation in the month of February, 1932, and since that date has been in continuous operation, milling an average of slightly over 3,000 tons of ore a month. The ore treated in the Bralorne mill is a gold-bearing quartz containing a very small amount of silver. About 75 to 80 per cent of the gold is in the form of free gold, the principal remaining portion being intimately associated with pyrite and arsenopyrite. The gangue rock is quartz, together with varying but relatively small amounts of altered diorite or albitite. In some of the ore, usually the higher grade portions, there is also considerable talc, which forms much slime in grinding. The mill is situated near the portal of the main haulage tunnel and the ore is received directly from the mine ore-trains, which dump on to the grizzly over the coarse-ore bin of the crushing plant. Figure 1 shows the flow-sheet of the mill as it is now being operated. Various changes have been made in the flow-sheet and in the reagents since the commencement of operations, and doubtless minor changes will continue to be made in order to increase the efficiency of the mill. Among the more important changes were those from two-stage to single-stage grinding, and from amalgamation plates to blankets. The change in the crushing was made because too much crushing was done when both primary and secondary mills were employed.

Jan 1, 1933

By E. Lehtila, J. J. Talja, R. Jahila

Kopar Oy is acknowledged for engineering and manufacturing of robust systems for bulk material handling, especially at power plants and non-ferrous smelters. We have over thirty years of experience with systems specifically designed for hot and abrasive conditions, aiming at low cost of ownership, low operational expenses and high availability. Although Kopar has numerous applications in mechanical conveying, there is an increasing number of pneumatic conveying applications at copper smelters. They relate to conveying of concentrate, and primary and secondary flue dusts. Challenges of pneumatic conveying for concentrate are mechanical and do relate to broad particle size distribution and high abrasivity of the concentrate and the silica. Therefore, special attention shall be paid to system design and ceramically lined bends in the pipeline. Challenges of pneumatic conveying of primary flue dust relate predominantly to material stickiness and poor flowability which are mainly due to fine particle size and formation of sulphates and furthermore, crystalline water. Additional challenges of secondary dust, the white converter dust, are primarily due to the extremely fine 0.1–1.5 µm particle size and problems which come with this. Effect of material characteristics like size distribution, morphology and chemical composition in pneumatic conveying are discussed in detail. INTRODUCTION Fine materials like concentrate, feed mix, flue dusts (from waste heat boiler and electrostatic precipitator) and secondary dusts need to be conveyed at smelters. Both horizontal and vertical conveying and combination of those are used. For the purpose, both mechanical and pneumatic conveying are applied. Most widely used equipment are drag chain conveyors and various combination of pneumatic systems, e.g. air lift, dense-phase and dilute phase pneumatic conveyors. Kopar has 30 years’ experience with multiple material handling systems. Furthermore, acquired companies like Elmomet Oy and SITE Oy (both currently fully merged and integrated into Kopar Oy) have even longer history, especially in pneumatic conveying. It is commonly known that the finer the dust the more difficult it is to be conveyed pneumatically. Sulfates with crystal water makes it all even more difficult, if not ineligible. Challenges related to pneumatic conveying of various fine materials is discussed in detail in the paper.

Jan 1, 2019

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By K. Sinding, R. Poulin

"Recent land-use decisions in British Colwnbia, and the publication of a report on compensation for expropriations of resource interests, have highlighted the nature of land use policies. Landuse decisions, such as the creation of large new parks, raise three principal issues which have implications for how land-use policy is conducted and how it impacts on the mining industry. The first is the identity of the parties advocating different land-use policies and their motives for doing so, the second is the changing nature of benefits derived from land, and the third is the change of property-rights regime which is devised to accommodate the (changing) benefits from using land and natural resources, as well as the interests of the different parties involved.Involved Parties and BenefitsThe process of establishing or modifying property rights depends on the interest groups involved. Three distinct categories, each with distinct incentives which can influence the process, must be distinguished: private claimants, politicians and bureaucrats (Libecap, 1989).The first groups claim rents and management powers through asset ownership. They may be incumbent owners seeking enforcement of the status quo, new claimants seeking redistribution of assets, or third parties who depend on the distribution of assets (e.g. lenders, labour suppliers and contractors). Some infonnal property arrangements can be negotiated within the group whereas others requires action in the political arena through lobbying politicians for (re)allocation of property rights and influencing bureaucrats for favourable administrative decisions. The second category is politicians, who direct the powers of the state to change or enforce property rights. Both incwnbents and office-seekers fall in this category and their actions and opinions are shaped by their constituencies and financial backers. However, not all causes can be championed and trade-offs have to be made, resulting in decisions that maximize political benefits. The third category of parties in the process is the bureaucrats. The power to manage has been delegated by politicians but bureaucrats also have opportunities and incentives to further their own interests. These can include maintaining or expanding jurisdictional turf or increasing operating budgets (Libecap, 1989)"

Jan 1, 1994

In the last 30 years numerous mining plants have been developed in North America but only a handful of these have required freezing the area where the shaft was sunk. The most recent mine shaft to be sunk using this technique is located on an island off the coast of Louisiana. The project required the input and skills of numerous people in several companies, including the owner, engineers and contractors. The Cote Blanche installation is one of several mines in the area which extract salt from a dome which extends under the Gulf of Mexico. The geology of this area is, however, markedly different from others in the region because there is approximately 460 ft of water logged soil above the salt dome. Because it is not possible to sink a shaft in ground that is this soft, the overburden where the shaft is located must be frozen before excavation can take place. The Cote Blanche mine is a producing facility which was built in 1958 by the Carey Salt Company. The original facility included a 14 ft diameter production shaft and a 7 ft-8 in diameter service/ventilation/escape shaft. This system was installed by The Cementation Company. In 1996 the owner decided to improve both the mine ventilation and production hoisting system by installing a third shaft. This shaft would be designed to extract 650 tons per hour from a depth of 1600 ft and provide 500,000 cfm of ventilation to the mine at a maxium design pressure of 4 in WG. These parameters resulted in a requirement for a 16 ft finished inside diameter concrete lined shaft and a headframe designed as a pressure bulkhead. Because the mine would operate from one level only, the most efficient hoisting system for the application was determined to be a ground mounted koepe running on rope guides. With these criteria fixed Cote Blanche embarked on a program which would see construction start in June 1998 with the first salt produced in February 2001 at a cost of $US18M. The major players in the design and construction were G.L. Tiley & Associates Ltd., BLM Bharti Engineering, Freezewall Inc., Phillips Mining, Geotechnical and Grouting Inc., Don Hart Consulting and Dynatec International.

May 1, 2002

By W. P. Clement, M. C. Bell

"PT International Nickel Indonesia, a subsidiary of Inco Limited, mines and processes nickel laterite ores for the supply of nickel matte, primarily to the Japanese market. It has large ore reserves and a substantial portion of its energy requirement is supplied from its own hydro-electric plant. Since the early 1980s, the company has increased its production level and has dramatically reduced its unit costs. Projects are in progress to further decrease costs and recently a major expansion - 31% increase in nominal capacity - has been undertaken, consistent with marketing opportunity in Japan. The expansion project, which has a low capital cost per unit of production, is outlined in this paper.IntroductionPT Inco is a fully integrated mining and smelting facility located in Indonesia on the island of Sulawesi, and is based on a very large, world class nickel laterite orebody located 60 km inland from the Gulf of Bone. Construction of a single furnace line plant started in 1973. Complete supporting infrastructure of townsite, hospital, schools, shopping centres, road systems, and an airport, all had to be built. Prior to completing the first phase, the decision to expand the plant to a three kiln-furnace line was made. A major factor in the decision was the ability to develop the hydroelectric potential of the nearby Larona River. This involved construction of a 30 m high dam, and a 7 km surface canal to the generating station. The penstocks drop 150m to three 55 Mw turbines. The power generated is sufficient to supply the entire electrical load for the complete smelting complex and town site. The unique capability to supply the high smelting energy requirements for a lateritic nickel ore by fully captive hydro power, has, over the past decade insulated PT Inco from the large upward swings in oil prices suffered by other lateritic nickel producers.Wet ore is first partially dried to 20% moisture in two co-currently fired rotary driers, screened on an internal trommel, and delivered to two dry ore storage buildings. The partially dried ore is calcined at 750°C and partially reduced in three large 100 m by 5.5 m kilns. Reduction is accomplished by lancing bunker C oil onto the ore bed at the discharge end of the kiln. The kilns are equipped with five air pipes with onboard blowers to gradually bum the combustible gases generated by the lance oil. The kilns were also originally equipped with two side burners to supply additional heat close to the feed end of the kiln. Calcined ore is transferred by 20 ton refractory lined containers to the furnace feed bins at the top of the smelter. Smelting is carried out in three 18 m diameter furnaces powered by 45 Mw transformers. Slag is skimmed at 1550°C through water cooled breast plates and removed to the slag dump by Haulmaster Carriers. Matte of 25% Ni, 1O% S, 65% Fe is tapped at 1350°C into the converter aisle. The iron is slagged in converters to produce a nickel sulphide matte at 80% Ni. Three rotary Kaldo converters were initially installed. The product matte is granulated, dried, and shipped in returnable rubber bags to Japan. Most of the matte is fluid-bed roasted to nickel oxide and then directly reduced in a second reducing fluid bed reactor at our facilities in Japan.The smelting complex was designed to smelt two million tonnes of dry ore per year, equivalent to 34 000 tonne nickel production at an ore grade of 2% Ni. The cost of the entire project including working capital was $900 million."

Jan 1, 1990

By R. A. (Dick) McIvor

"It is important to ensure that the basic mine hoist plant design fundamentals are incorporated into any new mine hoist plant project before detailed design engineering is commenced. Some of the basic design fundamentals to be considered are: hoist rope fleet and flight angles for good hoist rope coiling, hoist rope harmonic frequency study to ensure that the hoist rope does not run at full speed at a rope resonance frequency, head frame and shaft clearance diagrams to establish the optimum positions for the loading and dumping of the shaft conveyances, access in the head frame and shaft collar for hoist rope and shaft conveyance installation and removal. Failure to consider the hoist plant fundamentals before detailed engineering commences will result in extra costs for hoist plant redesign or a significant increase in operating and maintenance costs for the mine due to increased hoist plant downtime to perform tasks and a lower mine operating efficiency. INTRODUCTION The mine hoisting plant is the most critical single line component in the operation of a shaft sinking operation or a permanent installation. Bad decisions in the design and selection of the hoist plant equipment can significantly add to the operating costs and up-time in the operation of the mine. Mine hoisting plant equipment installed costs represent approximately 5 to 8 percent of the capital cost of a new mine, yet price sometimes becomes the deciding factor for procuring the hoist plant components, sometimes selecting used equipment that may compromise the design and maintainability of the mine hoist plant. Mine downtime can cost upwards of $100,000 per hour and it will not take a very long time to eat up all the so-called savings on hoist plant equipment purchases. This paper will provide guidelines for the design, selection, installation and maintenance of mine hoist plant equipment with the objective to having the right mine hoist plant with the highest operational availability and best maintainability. PRELIMINARY DESIGN INFORMATION Before any engineering commences, the following information needs to be obtained to allow the preliminary sizing of the hoist plant equipment: • Shaft depth: The shaft depth will influence the hoist rope selection based on the material and personnel loads anticipated for the mine design. The shaft depth will also influence the maximum speed of the shaft conveyances. • Annual production: The desired annual production will influence the required payload sizing with allowances for maintenance and inspections of the hoist plant equipment."

Jan 1, 2019

By J. N. Cram

"The comments given are to help allay generally accepted ideas that the handling of arsenic as arsenic-trioxide (As2o3J in and from off gas pyrometallurgical operation fumes is difficult, hazardous and expensive. It need not be any of these things if the basic and rather unique chemic3l and physical properties are understood and taken care and advantage of through present day technologies. These particular characteristics are:-(1) As2o3 sublimes and re-condenses, at a relatively low temperature;(2) As2o3 is, for practical in-plant purposes, insoluble in water at ambient temperatures and quite soluble in water just below the boiling point;(3) residual suspended and dissolved As 2o3 can be removed from water by complete dissolution with very little sulfuric acid, followed by the addition of small amounts of ferrous sulfate and calcium chlorate, with oxidation to the ferric and arsenite state and precipitation of an insoluble ferric calcium arsenate, thereby lowering the As2o3 content of solutions to acceptable levels. Even lower levels of non-toxic forms of arsenic solids and residual As2o3 in the water solutions can be attained by also using phosphate, and lime, along with the above.A background re past arsenic processing methods, present day operations, plus predictions re future trends, and hazards, are outlined."

Jan 1, 1979

By Michel Dagbert, Mohammed Harfi

"Abstract - The Draa Sfar polymetallic deposit, at about 16 km NW of Marrakech in Morocco, is a massive sulfide zone at the contact between an underlying volcanic and an overlying clastics sequence. The mineralized body is a flat lens with schistosity and "boudinage," tilted to the west and with a strong dip to the east. The lens extends over a strike length of about 2 km and from surface to a depth of about 1 km, with thickness varying from 1 m to almost 30 m. It has been intersected by about one hundred surface drill holes and, in its south part, by about thirty underground fan holes from two exploration levels at depths of 300 m and 400 m. On these two levels, the massive sulfide zone has been channel sampled over a cumulative length of about 0.7 km. Results from drill and channel samples are used to estimate the resources of the orebody according to several methods: sections, polygons around intercepts on a longitudinal plan, grids on the same longitudinal plan with various distance weighting methods including kriging and, finally, a 3D grid with the same range of interpolators. A comparison of the various estimates delineates the important factors in deriving resources for this type of deposit. Those factors are mostly geological and related to the interpretation of the geometry of the two limiting surfaces of the zone. For the 3D gridding, the authors have devised a new and original method that constrains the interpolation of blocks from samples to a geometry of limiting surfaces. The resulting model shows internal grade variations that parallel fluctuations of zone thickness and orientation without having to re-orientate the search window in each block. Résumé - Le gisement polymétallique de Draa Sfar, situé à environ 16 km au NW de Marrakech est un horizon de sulfure massif au contact d’une formation volcano-sédimentaire de base et d’une formation détritique sur-jacente. Le corps minéralisé se présente sous forme d’une méga-lentille aplatie, schistosée, boudinée et déversée vers l’ouest avec un fort pendage vers l’est s’étendant sur une longueur de 2 km et une profondeur de près de 1 km avec une épaisseur variant de moins d’un mètre à près de 30 m. Il a été reconnu par plus d’une centaine de sondages de surface et, dans sa partie sud, par une trentaine de trous souterrains en éventail à partir de deux niveaux à des profondeurs respectives de 300 m et 400 m. Sur ces mêmes niveaux, des traçages ont permis de rainurer le minerai sur une longueur cumulée de 0.7 km. Les données de sondage et de rainurage ont servi à estimer les ressources du gisement selon plusieurs méthodes : sections, polygones sur longitudinale, grille sur longitudinale avec différentes pondérations en fonction des distances incluant le krigeage et enfin grille tridimensionnelle avec le même éventail de pondérateurs. La comparaison des estimés obtenus permet de mettre en évidence les facteurs importants dans l’estimation des ressources de ce type de gisement. Ces facteurs sont essentiellement géologiques et relatifs à l’interprétation de la géométrie des limites des corps minéralisés. Pour l’estimation sur grille tridimensionnelle, on a mis au point une technique originale qui calque l’interpolation des blocs à partir des échantillons sur cette géométrie des surfaces de contact. Le modèle résultant montre des variations internes de teneurs qui épousent les fluctuations d’épaisseur et d’orientation de la zone sans qu’il soit nécessaire de ré-orienter les fenêtres de recherche dans chaque bloc."

Jan 1, 2002

By J. E. Dutrizac

Canada is currently the world's largest supplier of zinc concentrates and is also a major producer of zinc metal. This dominant position in the world's zinc market is a fairly recent circumstance and, in fact, the country's zinc industry was founded only in the early part of the twentieth century. By contrast, the American zinc industry was well established by the mid-nineteenth century, largely based on technology originally imported from the still older European practice. Initial attempts to create a viable Canadian zinc smelter were based on the traditional practice and were unsuccessful; success came only with new electrolytic technology, much of which was developed domestically. The purpose of this paper is to outline the early attempts to produce metallic zinc in Canada and to trace the gradual development of these first efforts into a viable zinc industry based on modern science and technology.

Jan 1, 1999

By Robert B. Parsons

"The Whitehorse Mining Initiative (WMI) brought together all of the key stakeholders in Canada's mining industry to develop a framework whereby the industry can meet the challenges that it faces into the 21st century. The WMI Accord7 which was signed at the annual Mines Ministers Conference in Victoria, British Columbia, on September 137 1994, touches all of the important issues that confront the industry, including taxation. IntroductionSeptember 13, 1994, was a historical day for Canada's mining industry. On that day, on the occasion of the annual Mines Ministers Conference in Victoria, British Columbia, the Whitehorse Mining Initiative (WMI) Accord was signed by the leaders of the five principal stakeholders in the industry: industry; government; labour; environmentalists; and aboriginals. The Accord is the culmination of two years of hard work and intense collaboration by these stakeholders. But, the Accord is not the end result. The Accord can better be described as a springboard to a prosperous future for mining in Canada.The WMI had its beginnings at the Mines Ministers Conference in Whitehorse, Yukon, in September 1992 (hence, the name of the initiative). At that time, the mining industry was well aware of the serious challenges facing the industry, including significantly increased competition for mineral investment from other mining countries, coupled with an atmosphere of uncertainty surrounding land access, environmental regulations, and taxation. The diversion of investment abroad was hurting, and would continue to hurt, all Canadians. Something had to be done. At the 1992"

Jan 1, 1994

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By Mary Kama, Kaul Gena

"Magnetic skarn ore (MSO) is one of the major copper bearing ore extracted by the Ok Tedi Copper Mine in Papua New Guinea. Copper minerals are recovered by flotation while the iron not associated with copper are discarded as tailings. The objective of this investigation was to determine the iron ore reduction kinetics for the Ok Tedi MSO and ascertain if it can be processed to produce sponge iron for a mini steel plant in Papua New Guinea.SEM-EDAX analyses of the Ok Tedi MSO indicated 10.1% C, 30% O, 0.6% Mg, 1.1% Si, 21.1% S, 0.8% Ca and 36.2% Fe. Most of the iron is in sulfide form. Both naturally occurring and roasted sinters of Ok Tedi MSO samples of different particle sizes were reduced by charcoal carbon at three different temperatures and seven different reduction times. Analyses of the reduced products indicated a metallic iron content of more than 65 wt.% on average.Results showed that there was no significant difference in reduction between fluxed and control materials. Only a slight increase in kinetics with reduced particle size, hence the reaction rate constant (K) did not vary much within the temperatures investigated. Reaction kinetics increases with increasing reduction time at 900°C. Therefore, more iron reduction is observed with particles of 106 µm size. In addition, the results also confirmed that the reduction energy used was higher at 800°C and lower at 1,000°C. In summary, iron reduction can be improved but close monitoring of temperature and reduction times are essential to determine the reaction kinetics of the Ok Tedi MSO. INTRODUCTIONMost mines in Papua New Guinea mine large quantities of iron in the form of sulfides, carbonates, oxides and sulfates that are eventually disposed off as tailings. The Ok Tedi magnetic skarn ore (MSO) contains a significant amount of hematite, magnetite, siderite, ilmenite and pyrite that can be a source of iron. The mineralogical compositions of Ok Tedi MSO reveals more iron minerals than copper, yet all iron containing minerals are collected in the tails from the main copper production stream. Therefore, this study is conducted to investigate the possibility of producing direct reduced iron (DRI), or sponge iron, from the MSO. Such sponge iron may serve as the feedstock for electric arc/induction furnace based mini steel plants in Papua New Guinea."

Jan 1, 2016

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration . Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet ,Processing the are as received resulted I n 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J."

Jan 1, 1988

By Ken Wood, Luc Duval

"The development and operation of the milling circuits treating the different Selbaie orebodies are discussed in this paper. The project is reviewed from metallurgical evaluation through construction to present operating status. The current flowsheets are described, with discussion of some unusual features.IntroductionThe Selbaie concentrator commenced initial production in August 1981, treating underground B zone copper ore in a single 1500 t/d circuit. Throughput was increased to 1650 t/d in 1985. The mill was expanded in 1986 to treat ore from the A-I zone open pit; an independent circuit was added to selectively treat 5000 t/d of copper-zinc ore. Current total mill throughput through both circuits averages 7200 t/d with the production of approximately 270 t/d of copper concentrate and 230 t/d of zinc concentrate.This paper describes the stages involved in bringing the project from initial laboratory testing to its current status as one of the most important producers of silver, copper and zinc in Quebec and a major employer in the region."

Jan 1, 1990