Search Documents

By R. Tremblay, M. Burrows

"In the summer of 1990, pilot scale testing of a Jameson cell was carried out at Falcon bridge Limited, Kidd Creek Division. The Jameson cell is self aspirating and has fewer mechanical parts, thus it has a lower operating cost compared to conventional cells. This lower operating cost combined with positive pilot scale results, justified the evaluation of two full scale cells in the plant. The plant test had two mandates:1. Gain a thorough understanding of the cells operation and design constraints.2. Develop a flow sheet to replace three divisions of copper cleaner flotation.This paper provides an overview on the installation, commissioning and evaluation of the two Jameson cells acquired. The current status of the test program is also discussed.IntroductionThe Falcon bridge Limited-Kidd Creek Division concentrator is located in Timmins, Ontario. The concentrator, commissioned in 1966 and expanded in 1978, consists of four parallel grinding and flotation divisions utilising small cell (60 ft3) technology. With increasing pressure to maintain low operating unit costs a series of studies were undertaken to assess the impact of new technologies in the flotation circuits. The goals of the project were to improve productivity through increased metallurgical performance and/or reduced operating costs.One of the technologies investigated was the Jameson cell designed by Dr. Graeme Jameson of the University of Newcastle and marketed by MIM Holdings Limited, Australia. This style of column technology was chosen based on its potential for reduced capital and operating cost versus large conventional cells.The success of pilot testwork in 1990 led to the installation of two production sized Jameson cells beginning in October 1991. The units were to be used to confirm pilot results and determine equipment requirements for flotation modernisation. This paper will discuss the results and experiences Kidd Creek has had with the Jameson cell from pilot scale through installation and commissioning of the plant units."

Jan 1, 1993

By Mengsu Hu, Yuan Wang, Jonny Rutqvist

Material interfaces and typical boundary conditions are boundaries influencing the existence, uniqueness and stability of numerical solutions of water flow in heterogeneous media. The Numerical Manifold Method (NMM) with a two-cover-meshing system is an ideal method to handle boundaries, considering its flexibility with no need to adjust mathematical nodes onto boundaries, the meshing efficiency, and its integration precision. In this study, we derive and compare two new approaches for boundary constraints, i.e., a discontinuous approach with Lagrange multiplier and a continuous approach with jump function in the frame of NMM. In the discontinuous Lagrange multiplier method (LMM), Dirichlet boundaries or the material interfaces are regarded as discontinuities which are linked by Lagrange multipliers. In the continuous Jump function method (JFM), the material interfaces are regarded as inner interfaces, where the refraction law is realized by constructing jump terms with discontinuity of hydraulic gradient in its normal direction. Both the continuous and discontinuous approaches make full use of the aforementioned advantages of NMM and are established based on a clear physical meaning of water flow by our energy-work seepage model. The newly derived boundary-constraint approaches were coded into an NMM water flow model and tested for precision and efficiency on different simulation examples. We first tested both LMM and JFM for an idealized heterogeneous model, comparing the numerical results with analytical solutions. Then we tested both approaches with a heterogeneous model and compared the results of hydraulic head and specific discharge. We proved that both approaches are very suitable for material boundaries considering the accurate realization of the boundary constraints and the flexibility with no need for mesh-conforming.

Jan 1, 2015

By Joachim von Scheele

An oxyfuel-based technology - OXYFINES - has been introduced for in-plant recycling. It provides fines, dust, sludge (without any drying-step) and other by-products arising in the steel and metal producing industries to be recycled directly back into existing processes or a separate unit on-site. Results from full-scale installation (20,000 tpy) for dust treatment, full-scale and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. Processing rates at 3.5 t/h have been demonstrated. The product is agglomerates or lumpy pieces, the latter if the product has passed an all-liquid stage and thereafter been crushed. The technology does not only provide a solution to the problems connected to dust and sludge generated in metal production. It also turns these materials into a low-cost raw material useful for the production in question, thus replacing part of the raw material input in electric arc furnaces, blast furnaces, etc. Elements harmful to re-use of the processed dust or sludge, e.g., zinc and alkaline components in steel production, are removed as secondary dust, and material yield of main components for re-use is very high, about 98%. The paper reviews the concept, the results obtained and its status; its use for sludge recycling is emphasized.

Jan 1, 2004

The system of keeping geological plans and sections for the Geco Mine at Manitouwadge, Ontario, is described. Special methods employed to save draughting time with-out sacrificing accuracy, such as the extensive use of black line prints, are discussed. The uses made of the plans and sections by the mine planning engineers in their designs of stopes, and by the blast-hole engineer in ~is preparation of blast-hole layouts, are noted. An unusual scheme for portraying the distribution of .copper, zinc and silver values within the ore zone is de-scribed. The method of estimating the grade of ore to be "blasted in each ring of blast holes is outlined, as is the method of estimating the annual ore reserves. The design of an effective but simple transparent geo-logical and mine development model, used as a display for -visitors, is discussed. A large-scale model used for the study of problems in geological structure is also de-scribed.

Jan 1, 1964

By E. Talebi, P. Roghanchi

"This study aims to discuss personal and behavioral parameters contributing to heat-related accidents. To study the prevention approaches, it is essential to look at the various factors at the individual, management, and industrial levels. Qualitative risk analysis methods are used based on the public data in the USA to find the impact of the environmental and behavioral parameters on the heat stress and heat strain of mine workers. The effects of individual factors such as worker experience, age, fitness, lifestyle, acclimation, and more are illustrated. The significance of factors such as the roles of the mine management and regulatory agencies are addressed.INTRODUCTIONOccupational hazards in mining industry endanger the health and safety of the workers and productivity loss for mining companies. Among those hazards is the exposure to excessive heat that has adverse effects on the health of mine workers. The intensity of heat load is a significant factor in fatal and non-fatal heat-related accidents. Severe environmental conditions combined with a high level of activity in the mining industry increases the vulnerability of individuals to health and safety hazards (Ngwenya, Oosthuizen, Cross, Frimpong, & Chaibva, 2018). Lack of regulations and legislation addressing the heat issue in the mining industry (i.e., underground and open pit mines, processing plants) also raises widespread concerns.Along the climate change, various sources contribute to the overall heat load at a mine site (Hanna, Kjellstrom, Bennett, & Dear, 2011; Kjellstrom, Lemke, Hyatt, & Otto, 2014). In underground mines, the majority of heat comes from different sources such as geothermal gradient, equipment, auto compression, groundwater, and blasting (Maurya, Karena, Vardhan, Aruna, & Raj, 2015). On the surface, however, the majority of heat load can be sourced to solar energy. The exposure to excessive heat might result in heat-related illnesses, fatigue and fainting, loss of concentration, performance reduction, and production loss (Kocsis & Sunkpal, 2017; Roghanchi, 2017). The severity of the effects depends on duration and level of exposure and the response of an individual to heat stress. The response of an individual is influenced by different factors including age, gender, fitness, lifestyle, experiences, and past medical history."

Jan 1, 2019

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

Proper water and thermal management is essential for obtaining high performance of Proton Exchange Membrane Fuel Cells (PEMFCs). A steady, two-dimensional water and thermal management model was developed, aiming at considering pressure drop, open circuit voltage variation with stack temperature, water vapor effects on membrane conductivity, which made the model physically more reasonable and more suitable for various operating conditions. The model could predict the distributions of a series of important parameters along the flow channel, and thus the effects of various operating and design parameters on the fuel cell performance could be investigated easily by numerical trial-and-error method. The modeling results compared well with the available experimental results from the literatures. The results also showed that the humidification is crucial for the performance of PEMFCs. The model could be a very useful engineering tool for the optimization of PEMFCs.

Jan 1, 2005

By M. Kucharski

The model of the Outokumpu direct-to-copper process deals with a steady-state process the parameters of which do not depend on time. To give a prediction for the process outcome, "a modified black box" method, which ignores most of the chemical reactions in the furnace, was used. This method takes input and output parameters into consideration. The presented model describes the Outokumpu direct-to blister process in the form of the set of linear equations which give mass and enthalpy balances as well as the distribution of elements between blister copper and slag. However, only major substances where quantities in the feed charge exceed a certain level (for example 0.5 kg/ lMg of smelted concentrate) are taken into consideration. Minor elements are distributed among slag and metal phases in a different way. Some of the equations are derived from distribution coefficients. The value of distribution coefficients can be calculated from plant production data.

Jan 1, 2007

By L. P. Chrismas

"IN 1975, Nova Scotia produced 1.8 million tons of coal with a FOB mine value of $47.6 million. Of this total, about 30 per cent or 600,000 tons was coking coal and the remainder was steam and industrial-grade coal. The Nova Scotia Power Corporation consumed 630,000 tons in three generating stations and 570,000 tons were sold to Sydney Steel for making coke for its steel operations. Exports, principally to Great Britain, comprised 370,000 tons in 1975 in addition to the 300,- 000 tons shipped to other provinces for use by cement and pulp and paper companies. In 1975, just over 100,000 tons of coking coal were imported into the province from Alberta. Before 1975, low-volatile coking coal was traditionally obtained from the United States. In 1975, production came from seven individual mines and one project involving reclamation from mine dumps in Pictou County. Of the seven producers, four are owned by the Cape Breton Development Corporation, a federal Crown corporation; the remaining three are small independent mines, but, even though small, they are sizeable contributors to the economies of their local areas. After 101 years of continuous operation, Devco's Princess mine was closed in 1975. The Nova Scotia coal industry, in terms of value, accounted for about half of total mineral production in 1975. The industry provides jobs for 3,000 men and women. It is also significant that in 1975 Nova Scotia produced about 6.5 per cent of Canada's total coal production of 28.3 million tons. Detailed statistics on Nova Scotia's coal industry appear in the Appendix."

Jan 1, 1976

By A. Ghirian

Once cemented paste backfill (CPB) is transferred and placed into a mine stope, various coupled mechanisms will take place in the CPB material or structure. It will be subjected to strong coupled thermal (T), hydraulic (H), mechanical (M), and chemical (C) processes. Field studies have shown that the in-situ properties and performance of CPB differ from those obtained in the laboratory. This is mainly due to effects of the aforementioned coupled THMC mechanisms or processes. For a reliable and cost-effective design of a CPB structure and barricade, it is crucial to have a proper understanding of the THMC behaviour and evolution of CPB. Also, it is important to consider the effect of coupled THMC factors (e.g., self-weight pressure, drained/undrained and thermal conditions, pore pressure) while curing the CPB specimens. For this purpose, a laboratory setup is developed to investigate the properties of CPB materials. The setup is capable of curing CPB specimens (10 cm in diameter and 20 cm in height) under controlled vertical pressure (curing under stress) and various coupled THMC conditions, while continuously monitoring the evolution of total stress, pore pressure, suction, temperature, water drainage, chemical composition of the pore water and vertical deformation. Once the required curing time is achieved, the specimen can be extracted and then subjected to experimental tests of interest, such as those that determine the Unconfined Compressive Strength (UCS), shear strength parameters, saturated hydraulic conductivity and thermal properties. In this paper, we describe the developed experimental setup and present some results of the THMC behaviour of CPB under various curing stresses and rates of backfilling. The obtained results show that the THMC properties of CPB are strongly coupled due to several mechanisms, such as self-weight pressure, heat of hydration and suction development as a result of self-desiccation. The findings can assist researchers and practitioners to better understand THMC behaviour and thus design more cost-effective CPB structures.

Aug 1, 2013

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By O. Espinoza Ortega, S. Song

A process scheme has been devised to improve the silver recovery and the grade of concentrates from the scavenger concentrate of a silver ore flotation circuit. Based on modal analysis studies it was found that silver sulfide minerals in the scavenger concentrate were associated as simple binary particles and finely disseminated in sulfide and non-sulfide gangues. Fine grinding of the concentrate improved the grade-recovery curve of silver to a very limited extent owing to heterocoagulation between liberated fine silver sulfides and coarse particles of gangue. This heterocoagulation phenomenon was prevented by grinding the concentrate in the presence of the dispersing reagent sodium hexametaphosphate. The silver grade-recovery curve was improved by practicing. before the conventional flotation step, a selective aggregation step for the fine silver sulfide particles using the non-polar oil kerosene, the sulthydryl collector Aerophine 3418 and conditioning the pulp under strong agitation conditions.

Jan 1, 2004

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By J. A. Finch

The metallurgical performance of a flotation cell is strongly influenced by the features of the bubble population, characterized by the gas dispersion properties, a collective term including bubble size, superficial gas velocity and gas holdup. It is required that gas be well distributed throughout the cell. Gas distribution is estimated here by simultaneous measurement of gas velocity (Jg) at different distances from the center (radial Jg mapping). This communication describes a technique to perform radial Jg mapping together with fundamentals for the interpretation of the data.

Jan 1, 2009

By A. Dahi Taleghani, Amir Shojaei

A continuum damage mechanics (CDM) based constitutive model has been developed to describe elastic, plastic and damage behavior of rock during drilling. In addition to inelastic deformations, this model incorporates rock anisotropies like toughness anisotropy due to the bedding planes orientation that is a common observation in soft Shales. The pressure sensitive inelastic deformation of porous rocks together with their damage mechanisms are studied for drained and undrained conditions. Fracture mechanics of microcrack and micro-void nucleation and their coalescence are incorporated into the formulation of the CDM models to accurately capture different rock failure modes. The performance of the developed elastoplastic and CDM models are compared with the available single cutter test data of a specific shale play and then the models are introduced into a commercial finite element package through user-defined subroutines. A workflow to derive the required model parameters is presented through inverse modelling of the single cutter test data. The developed CDM model outperforms the traditional discrete element and fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures like formation of the cuttings ribbon without any essential need for remeshing. This model would provide a robust tool for modeling bit performance and rate of penetration using conventional elements of FEA with a reliable results and a computational cost less than similar computational techniques like discrete element methods.

Jan 1, 2015

By Randolph A. Pax, Brian Cornish

The operation of grinding mills in an ore processing circuit is supported by monitoring the input and output variables. These can include the feed ore size distributions, ore feed and water addition rates. The outputs can include the discharge undersize density, oversize tonnage rate and the P80 of the discharge. The grinding mill performance is judged by the power draw, recycle rates and discharge grind size. Conditions inside the mill are inferred from loads cells or bearing pressures and past histories. An overall noise value is sometimes used to evaluate the load as well as the occurrence of excessive impacting of steel balls onto the liners/lifters of the mill. This paper presents results of the internal behaviour of a mill using non-contact stationary microphones located close to the mill outer shell (Pax, 2012). The noise generated by a mill can be attributed to a number of events that occur inside these mills and suitably analysed can provide real-time determinations of in-mill behaviour and can provide powerful insights into the operation of the primary comminution tumbling mills. The acoustically determined signals including a specific 'steel' signal, water hold-up, integrated area together with a classification of impact events. Specific results from case studies will show information of the trajectories inside a mill, steel to rock ratio as well as rheology effects. By incorporating a self-consistent understanding methodology for the in-mill processes from an array of microphones, the information can be used to diagnose the dynamic conditions inside a mill.

Jan 1, 2016

By Young Hyun Paik, Hyung Sup Choi, Yeun Sik Kim

The basic studies on the surface properties and flotation characteristics of ilmenite were made by electrophoretic, adsorption, contact-angle and floatability measurements. The isoelectric point of ilmenite is found to be at pH 5.6. By combining the results of electrokinetic studies and adsorption measurements, a clearer picture of the ilmenite-solution interface was observed. These findings were correlated with the floatability of ilmenite obtained by Hallimond tube tests. The general flotation characteristics of ilmenite are compared with those obtained for magnetite and rutile. It is indicated that the above three minerals, namely, ilmenite, magnetite and rutile, have very similar surface properties and flotation characteristics. Therefore, it is difficult to make an effective separation of these minerals by flotation. However, it is found that sodium orthophosphate acts as a selective depressant for magnetite in anionic flotation. Therefore, close pH control of the pulp in the presence of the phosphate ion enhances the possibility for a successful separation of these minerals.

Jan 1, 1967

By D. A. Le, T. S. Nguyen

"In Canada and other countries, several types of rock formations are being considered for the geological disposal of radioactive wastes. In order to better understand the ability of these rocks to contain and isolate the wastes, the Canadian Nuclear Safety Commission collaborates with different international research organizations and has access to experimental data from Underground Research Laboratories (URLs) in the world. Such an URL is situated in Opalinus Clay, at Mont Terri, Switzerland. An experiment, consisting of the excavation of a tunnel followed by water and gas injections in a test section of the tunnel, was performed at the URL. The authors have developed a mathematical model, based on the poromechanics theoretical framework, to simulate those phases of the experiment. The constitutive relationship for the stress-strain behaviour of Opalinus Clay takes into account its inherent anisotropy due to bedding. The model was able to capture the main features of the experiment such as the prediction of the shape and extent of the excavation damage zone and its influence on water and gas migration.INTRODUCTIONIn Canada and many other countries, several types of rock formations such as crystalline rocks and sedimentary argillaceous rocks, are being studied for the disposal of used nuclear fuel from nuclear power plants. Geological disposal relies on multiple natural and engineered barriers for the long-term containment and isolation of the wastes. The host rock is a major natural barrier and is the subject of extensive research. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URLs)."

Jan 1, 2015

By James F. A. Hatley

Northern Saskatchewan comprises an area of about 350 000 km2 and boasts some of the world's largest known high-grade uranium deposits. The successful mining of these deposits, however, can not be accomplished without overcoming technical challenges. Not only is the high grade of the uranium ore challenging, but mining methods need to be developed to deal with groundwater at very high pressures, and ground conditions that vary substantially from excellent to wholly unconsolidated clays and sand. This paper discusses the various mechanisms of inflows at the three of the Cameco Corporation Mines in Northern Saskatchewan. The risk of inflows is quantified in terms of unique challenges from hydrogeologic conditions, rockmass integrity, and uncertainty in geologic conditions. Mitigation strategies in case of an inflow are also briefly described. The paper concludes by addressing the impact of institutional rules (corporate standards) on minimizing, monitoring, and controlling the probability and/or impact of unexpected inflows.

Aug 1, 2010

By K. Sawamukai, S. Ogasawara, D. Umenai, T. Tsuruta

"Removal of cobalt, strontium or cesium ion from the aqueous solution containing each metal ion only using microorganism was examined. Arthrobacter nicotianae which had a high ability to remove cationic metal ion was used for the removal of each metal. The removal of cobalt, strontium or cesium using A. nicotianae cells was affected by the solution pH, concentration of metal ion, and cell amount. The effects of above mentioned factors on the removal of each metal and time course of strontium from the solution containing each metal only using A. nicotianae cells were reported in this paper. INTRODUCTIONRadioactive elements, such as cesium, iodine, strontium, plutonium, barium, cobalt, lanthanum, yttrium, and tellurium, were detected around Fukushima Daiichi nuclear power plant, which was damaged by the magnitude 9.0 earthquake and the tsunami followed.The removal of radioactive elements from contaminated sources is a worthwhile subject to investigatein terms of environmental control. Research efforts have been especially concentrated on studying microorganisms that remove uranium including bacteria (Andres et al, 1993, Hu et al, 1996, Marques et al, 1991, Strandberg et al, 1981), actinomycetes (Byerley et al, 1987, Friiss and Myers-Keith, 1986, Golab et al, 1991), fungi (Byerley et al, 1987, Galun et al, 1983a, Galun et al, 1983b,Tsezos and Volesky, 1981, White and Gadds, 1990) and yeasts (Strandberg et al, 1981, Schmate II et al, 1978).We have investigated removal and recovery of uranium from aqueous systems using microorganisms isolated from uranium mines. We identified some strains of bacteria with extremely high uranium removing abilities (Sakaguchi et al, 1996), and thus, the microbial biomass may be considered as an adsorbing agent for the removal and recovery of uranium and heavy metals present in aqueous systems around Fukushima Daiichi nuclear power plant.In the present study, we screened various species and strains of bacteria, actinomycetes, fungi, and yeasts for their ability to adsorb uranium (Tsuruta, 2002). Basic features affecting uranium adsorption?co-existing cations and anions, cell amounts, pH, and the adsorption time course?by Arthrobacter nicotianae cells, which adsorbed the largest amount of uranium, were also investigated. In addition, we examined the removal of an other actinoid element, thorium ion, which may be present with uranium in refining effluents.In this paper, the removal of cobalt, strontium, or cesium from the solution containing each metal ion using A. nicotianae cells is discussed."

Jan 1, 2012