Search Documents

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006

By G. E. Agar

"The distribution of gold in the grinding-classification circuit of an operating gold plant was determined by assaying the size fractions of samples from each of the streams. This analysis identified the streams with the maximum potential for gravity recovery of gold and revealed that there was up 110 seventy-five times as much gold in the primary cyclone underflow as in the concentrator feed.Laboratory jigging and tabling tests were done on samples from two of the streams to determine what the recovery might be with a gravity circuit and to show that a high grade concentrate could be produced. A numerical simulation procedure was used to calculate a material balance for a circuit that included gravity separation on the primary cyclone underflow. The numerical simulation optimistically indicated that as much as 84% of the gold might be recovered in a reasonable grade of concentrate even though the recovery in batch bench scale tests was only 14%.Incorporation of a gravity separation device would reduce the inventory of gold in the grinding-classification circuit.INTRODUCTIONMany gold concentrating plants include a gravity concentration operation while others do not and the reasons that some do and some do not is not clear. Some of the advantages and disadvantages of gravity circuits are discussed by Penman (Penman 1987) without clear cut resolution. Penman's comments elicited an interesting response from Lloyd (1989) who produced a simple way to determine if the addition of a gravity concentration circuit would enhance the recovery of gold. Lloyd's method does not consider the cost of running the circuit so it only partially answers the question. There are reports in the literature (Wells and Patel 1991, Matwijenko 1988) that as much as 60% of the entire production comes from a gravity circuit when it is used, and that the grade of the concentrate produced often exceeds 65% gold, an assay that far exceeds most Merrill-Crowe precipitates that are sent to refining. In at least one instance (Hood 1984) a range of recovery from 40-50% was indicated from laboratory test work and the plant subsequently realized recoveries in the range of 26-40%. Despite these favorable numbers other plants use gravity separation when as little as 20% of the gold is recovered in the gravity concentrate (Carter 1992)."

Jan 1, 1993

By C. W. Eggert

This paper gives an account of the E.V.O.P. tests made at the Copper Rand mill of the Patino Mining Corporation in Chibougamau, Quebec. The runs were made to acquire an understanding of the method. A description of events, along with conclusions, observations and opinions, is out-lined.

Jan 1, 1967

By Karl J. C. Harries

"8.1. INTRODUCTIONThe purpose of this chapter is not to provide precedents or examples of provisions, but rather to offer some comments that may be worth considering in the negotiation or review of an agreement. These comments are not intended to be exhaustive. It must also be noted that, although the chapter is written in the context of a common law joint venture, the concepts and concerns for the most part apply equally to a corporation that is owned by only a few shareholders for the purpose of participating in the project held by the corporation.The corporation has the advantage of having much of its organization established by local corporate law, but the particular wishes of the shareholders will appear in a shareholders’ agreement. The principal differences will be surprisingly small, save for the acquisition provisions that appear in a farm-in agreement1 and the substantial portion of the joint venture agreement devoted to creating and organizing the joint venture entity. Where the joint venture agreement refers to venturers and committees, the shareholders’ agreement will refer to shareholders and the board of directors, but both will have to deal with such basic matters as decision-making, default, dispute resolution, first refusals, funding, and carrying out work on the project. For convenience, this chapter usually refers to “venturers”, which may be taken to include shareholders.Negotiations give rise to many varying circumstances and concerns, and the main asset of the negotiator is an open and flexible mind. A desired result can often be accomplished indirectly in circumstances where the other side has adopted an inflexible position on a suggested approach. As precedents and standard forms tend to focus a negotiator’s thinking, they can be counterproductive. It is after the deal has been agreed to that a precedent can be of great assistance to the draftsman.The concepts are arranged in alphabetical order for convenience, not to suggest their sequence or position in an agreement or their relative importance. An agreement should adopt a progression of subjects in what the parties consider a logical sequence to read and work with. However, experience has indicated that it is best to set out in a single article the substance of the deal (i.e. the terms relating to the farm-in and what the acquiring party has to do to acquire his interest), preferably near the beginning of an agreement. The acquisition of the interest is, after all, the first order of business. The joint venture provisions will then follow in a reasonable sequence. It is also worthwhile to devote a single article to any special provisions that may apply during the earn-in period. For example, it may be provided that, although all work is to be done by the acquiring party as operator (with the duty of care, liability, and reporting requirements as set out in the joint venture sections of the agreement), but during the acquisition period, the acquiring party, acting as operator, may be at liberty to do such work as he wishes, without the need for any committee or other approvals, and committee meetings may be suspended.2An agreement is divided into paragraphs and articles to make it easier for the parties to read and understand, and to assist a party in finding “that provision” when the need arises. A comprehensive table of contents will also assist the parties who must work under an agreement. An added benefit of a table of contents is that in preparing it, the draftsman sees the overall structure of the agreement and will often catch and correct flaws."

Jan 1, 2003

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954

By T. R. Carter, A. C. Colvine

"Rocks of the Grenville Province in southeastern Ontario are currently largely dismissed by many geologists as having little or no potential for discovery of significant deposits of metallic minerals. The present study demonstrates that the area contains numerous deposit types which elsewhere are major metal producers. Therefore, there is significant unrealized potential, especially for gold, zinc, uranium, and possibly copper.The variety of deposits of metallic mineralization include stratiform zinc in marbles; stratabound base metal sulphides in volcanic and sedimentary hosts; gold-quartz veins; quartzmagnetite iron formation; copper-nickel and iron-titanium in intrusive rocks; magnetite skarns; molybdenum in skarns and pegmatites; uranium and thorium in pegmatites, veins, and calc-silicate gneisses; hematite veins; dolomite marbles (magnesium); and barite-jluorite-celestite-galena-calcite veins. There has been significant production of iron, lead, zinc, magnesium, gold, silver, and uranium.The vast majority of the metallic mineral deposits are confined to late Precambrian supracrustal and related intrusive rocks of the Grenville Supergroup. Many of the deposits are stratiform and/or stratabound and occur within units toward the top of major volcanic successions and in the lower portions of younger carbonate-clastic sedimentary successions.Processes responsible for mineral concentration in the area include: (I) syngenetic hydrothermal activity related to both volcanism and sedimentation; (2) epigenetic processes related to diagenesis, regional metamorphism, and igneous intrusive activity; (3) magmatic processes related to igneous intrusions; and (4) supergene concentration and enrichment. The genetic classification of the mineral deposits presented is based on observed geological relationships and these interpreted geneses. The deposit types have counterparts in volcanogenic and sedimentary exhalative, Mississippi Valley type, magmatic, contact metasomatic, and lode gold deposits. Many of the exploration criteria for deposits of these types may be applicable in the Grenville Province, despite the generally high metamorphic grades and complex deformation."

Jan 1, 1985

By Leiting Yue, Peng Ren, Yu Shen, Zhihong Liu, Haibao Shao, Longgong Xia, Feng Yu

The Kennecott-Outotec Flash Converting technology has been proven as an advanced and mature process in 5 individual plants during the past 2 decades. High grade copper matte (65–72%) produced in the flash smelting, or other smelting technologies is granulated to 3-5mm granules in a water torrent, and further crushed to fine powder (≈50µm) and dried to contain less than 0.3% H2O. Oxygen enriched air, together with fine copper matte powder and lime flux are injected into the reaction shaft by a matte burner. The copper making and slag making reactions will happen in very short time and distance during the particle falling and settling. However, industrial practice has found negative effects caused by sodium contamination. Na is introduced in the copper matte granulating process, and appears as Na2SO4 on particle surface. When Na content was high, scaling problems in the boiler will be worse, and the processing air will be blocked by the growing accretion around the matte burner, and as-produced blister copper is always high in S and O. In this present study, an industrial matte sample was used in the experimental work. Na was introduced into the matte powder by Na2SO4 solution soaking. The burning behaviour of the doped copper matte powder has been investigated as a function of the impurity concentration and processing temperature. Morphology and composition of these samples explained how Na2SO4 converts and reacts in the oxidizing atmosphere, and how they or their converting species influence the burning behaviour of matte particles. Cross-sections of as-prepared samples were analyzed with SEM-EDS, and the reaction mechanism has been carefully interpreted. Results from the present study can benefit both academic and industrial people. INTRODUCTION "Flash Converting" technology was developed jointly by Kennecott Utah Copper Smelter and Outotec (Finland) OY in 1992. The first industrialization of the technology was in Utah Smelter in 1995. Since 2006, it has been successfully applied in Xiangguang Copper, Tongling Jinguan Copper Branch, Fangchengang Jinchuan Copper, and Ningde Southeast Copper. The technology has also been further developed in those smelters. At present, roughly 2 million tons blister copper is produced annually through the Kennecott-Outotec Flash Converting technology, accounting for more than 10% of global primary copper production. The technology has advantages of high efficiency, high sulfur capture rate, good in environmental issues, mature equipment supporting, high automatic control level, low comprehensive energy consumption and flexible connection with the smelting unit, which make the technology to be one of the best choices in investing a new large-scale copper smelter or updating an old copper project in the world.

Jan 1, 2019

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By J. Budac, R. Kofluk, S. Mankasingh

Stainless steels such as 316L or 304 are normally relatively resistant to attack by nitric acid. However research at Sherritt International’s Fort Saskatchewan Operation reveals that when the stainless steel is immersed in an aqueous system in which nitric acid is used to dissolve metals such as cobalt or nickel, the steel can be seriously corroded. Sherritt is patenting a simple process for arresting the corrosion via the use of copper. This process is expected to substantially eliminate corrosion in processes where nitric acid is used to dissolve metals attached to a stainless steel substrate.

Jan 1, 2014

By Rowena Anderson

Mining companies are now looking for more effective ways to engage the community in public participation. Consensus-based approaches are becoming the most popularly applied way of achieving meaningful public participation. This paper introduces the principles surrounding consensus-building approaches and the processes for getting them started. The Healthy Communities Movement is one such consensus-based approach that offers a well-established holistic model for conceptualizing a healthy sustainable community. It also highlights the importance of public participation as an essential component of achieving a sustainable community. The paper concludes by illustrating how current company-community relations programs can utilize these models.

May 1, 2002

By Edouard Asselin, Tasawar Javed

This study was conducted as a part of ongoing work to characterize sulphide concentrate leach residues generated under CESL (Cominco Engineering Services Limited) and Vale pilot and demonstration plant medium temperature (150 °C) process conditions. Three different samples were analyzed. Derivative samples were prepared by extracting gypsum, sulphur and amorphous/poorly crystalline iron oxyhydroxide phases from the leach residues. Thermal behavior of the samples was studied by thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) in the temperature range 25 to 800 °C in both air and nitrogen atmospheres, with XRD analyses both before and after heating. Thermal transformation temperatures for different iron oxides/oxyhydroxides present in hydrometallurgical leach residues vary over a wide range which suggests the variable crystallinity of the phases. Raman spectroscopic analysis was carried out to help identify the type of iron phases in the residues. Furthermore, hydroxylamine hydrochloride (HaHC) and oxalate extractions were used to compare the fractionation of the amorphous/poorly crystalline iron phases in the residues. Given the compositions of the residues, any thermal events in the temperature range of 200 °C to 480 °C were attributed to amorphous/poorly crystalline iron phases.

Jan 1, 2014

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

By Sean Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by using assets more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the ?productivity paradox,? where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the true source of benefits is in how effectively IT is used. Most business sectors have accepted that the reengineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors but unique operational processes. The lessons of changing business practice in more common business processes such as inventory control and customer-supplier relationships can be adequately transposed into a mine. The unique operational processes in mines, in turn require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manger training simulators. This paper reviews the latest IT products and ou lines the processes and kinds of change that will be required in order to benefit from these new investment options.

May 1, 2002

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

A pre-flotation process of the Kupferschiefer ore with only frothers produces a concentrate enriched in carbonaceous matter and tailings for further upgrading steps. A partial removal of easy-to-float components of the feed before the main enrichments steps by flotation (rougher, scavenger) improves overall efficiency of separation of valuable elements from the ore. Since the types and doses of frother used for pre-flotation effect the process, the aim of this study was to determine the influence of selected frothers on the efficiency and selectivity of the Kupferschiefer ore processed by KGHM Polska Miedz S.A. A series of pre-flotation tests in the presence of different poly(propylene glycols) ethers, poly(ethylene glycols) ethers and aliphatic alcohols were conducted. The obtained results indicated that the types and doses of frother determine the flotation selectivity of copper and total organic carbon. The evaluation of the pre-flotation process was based on the analysis of selectivity parameters calculated from the recoveryrecovery Fuerstenau upgrading curves as well as the values of copper and organic carbon grades in the flotation products. It was shown that pre-flotation performed in the laboratory scale using a suitable frother provides higher overall flotation selectivity of organic carbon with lower overall flotation recovery of copper in comparison to flotation without the pre-flotation step. Thus, the pre-flotation process improves the quality and quantity of the final concentrates produced from the Kupferschiefer ore.

Jan 1, 2016

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007

By Raj Rajamani

In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal?s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned. First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized.

Jan 1, 2012

By G Zahary

THE most acceptable approacl1 to analyzing rock behaviour, at the present time, is based on the application of principles of mechanics and strength of materials. Analyses have been made in which the criterion of failure is based on maximum stress (1) and on Mohr's rupture theory (2). If such analyses are to be carried out, the mechanical properties of the rock must be known within acceptable limits. Although an adequate correlation of laboratory test results with field conditions has not been established, test results have been published (3) on the basis of their comparative value. That is, test results may be useful for comparing the behaviour of different rocks under similar loading conditions or of a particular rock under different loading conditions. This study aims at establishing some of the mechanical properties of an andesite rock by testing specimens cut _from diamond drill core. Drill core (EX) was provided from run-of-mine drilling by New Dickenson Mines Ltd. and Campbell Red Lake Mines Ltd.

Jan 1, 1963

By R. P. Charbonnier

"To understand the operation of jigs and other separating processes based on differences in gravity, it is desirable to analyse the motion of various particles in given media under specific conditions. A summary of the earlier theories shows that they lead to unsatisfactory or excessively complicated formulae in cases such as coal jigging. By adopting a simplified theory of the motion of particles in a fluid, the size and duration of the initial accelerated motion of a particle falling in hindered settling can be calculated. Based on this mathematical analysis, examples referring to actual coal jigging practice show that it is desirable to prolong and/or repeat, as frequently as possible, the optimum conditions corresponding to an effective acceleration of the particles. The separation is then obtained according to gravity rather than to particle dimensions, as would be the case if the velocity of the particles• were allowed to approach its terminal value. To achieve this gravity separation, it is suggested that the suction phase of the jigging cycle be artificially prolonged and the frequency of pulsations increased as much as possible for washing the coals of smaller sizes."

Jan 1, 1959

By Jehan Rondot

Les trois intrusions alcalines de Suzorite en haute Mauricie, bien que non datees, son! sans doute d ,attacher aU)( nombreuses autres intrusions alcalines dispersees sur les blocks Grenvillia et Laurentia et datees de I 050 Ma =t= 10%, done reliees d l'orogene grenvilien. L 'utilisations de la Suzorite est liee d sa forte proportion de phlogopite (>50%). Le rapport Mg/Fey varie de 3 d 7. Sa mineralogie et sa composition particulieres (forte proportion de Mg, Ket H20) en font son attrait.

Jan 1, 1984