Search Documents

By K. G. Eriksson

"The first tentative test made to try rubber lining in grinding mills was made in the early twenties. However, because of poor rubber compounds and design the results did not prove to be promising.In the early sixties successful trials of rubber linings were carried out as a result of a cooperation between boliden AB and Skega AB.One of the reasons rubber was not used earlier for linings was the difference in wear characteristics between rubber and steel. The ability to successfully develop rubber mill liners depends on three factors:l. Design2. Material (rubber compounding)3. Experience (knowledge)DESIGNThe main difference between steel and rubber, in material aspect, is the elasticity and the low tensile and shearing strength of rubber. It is necessary to take maximum advantage of the elasticity and to reduce tensile and shearing forces by minimizing the sliding of the mill charge. This is accomplished by using the Lorrain type of liners, i.e., lifter bars and plates. It is, however, necessary to keep a certain balance between lifter bars to optimize liner life and grinding performance."

Jan 1, 1983

By L Tafaghodi Khajavi, M. Barati

The distribution of phosphorus between solid silicon and iron-silicon melt was determined to investigate the degree of phosphorus removal from silicon by solvent refining with iron-silicon alloys. The distribution coefficient which is the ratio of the mole fraction of phosphorus in solid to that of liquid is as follows: 0.22±0.02 (1310°C), 0.29±0.02 (1260°C) and 0.33±0.02 (1210°C). The removal percentage of phosphorus is: 84.2% (1310°C), 72.5% (1260°C), and 63.7% (1210°C). The average phosphorus content of produced silicon in the proposed solvent refining process would be over two times less than that of the conventional directional solidification. The values of interaction coefficient of phosphorus on iron at different temperatures were obtained as -3460±155 (1310°C), -3595±159 (1260°C) and -3694±119 (1210°C). Self interaction parameter of phosphorus at different temperatures are as follows: 68±4 (1310 ?C), 78±10 (1260 ?C) and 103±19 (1210 ?C). The calculated values for distribution coefficient of phosphorus at infinite dilution are: 0.22±0.00 (1310°C), 0.30±0.00 (1260°C) and 0.34±0.00 (1210 °C).

Jan 1, 2015

By P. -A. Bosse, J. Robitaille, P. Blatter

The LaRonde ore is a Cu-Zn-Pb ore with gold (3-4 g/t) and silver (60-100 g/t). The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation. Subsequent to a recent mill expansion, excessive gold was reporting to zinc concentrate with a concurrent decrease in gold to copper concentrate. Owing to the higher return obtained from the metal, the mill endeavors to recover additional gold and silver to the copper concentrate and minimize the placement of precious metals to the zinc concentrate. A gold deportment study showed that the gold occurs mainly as küstelite, with a moderate amount of electrum and a minor amount of native gold. It also showed that various sulfur-based Au-and/or Ag-bearing coatings on liberated küstelite and electrum were the major mineralogical factors that caused gold and silver to report to zinc concentrate. By frequency, such coatings were observed on 70-80% of total liberated gold particles reporting to the zinc concentrate. Based on the gold deportment and the chemistry of the coatings, the collector chemistry was reviewed and a new collector was added into the circuit which resulted in a significant increase in gold and silver recovery to the copper concentrate. The information obtained from the mineralogy confirmed and guided other process optimization. In this paper, the authors will describe the process mineralogy of the LaRonde ores, and in particular, the mineralogical evidence diagnosing the problem. Reference will also be made to the rationale behind how the problem was solved, the results achieved, and future steps in optimization.

Jan 1, 2005

By F. A. McLean

The past decade has witnessed a rapid increase in the number and variety of uses found for internal combustion engines in mining operations. Gasoline engines are now widely used for operating core drills, pumps, compressors, small hoists, switching locomotives, tractors, boats, and other equipment. The heavy-oil engine is employed for operating compressors, generators, shovels, ore-milling machinery, and- in the iron, copper, and coal districts- in connection with that' latest newcomer in modern railroading, the oil-electric locomotive. Each of these applications could well form a subject for a lengthy treatise in itself. This paper, however, will be confined to a discussion of some of the features of internal combustion engines as applied to mine compressing plants and mill drive. Perhaps at no time in the history of mining in Canada has the search for new mines been more vigorously carried on, more old properties rejuvenated, or more remote districts exploited than during the past three years. The mine operator of today has a far wider range of equipment and facilities at his disposal than had the pioneers of Rossland, Cobalt, or Porcupine. Each year now witnesses the hinterland driven farther and farther back as improved forms of transportation, machinery, and methods make possible the exploration of properties once considered too inaccessible to warrant serious attention. Howey, Sherritt-Gordon, Callinan-Flin Flon, Jackson-Manion, Picard Gold Mines, and a number of properties in British Columbia, afford excellent examples of work carried out on an extensive scale miles from a railway, or in comparatively inaccessible mountain regions.

Jan 1, 1928

By W. McCombe, G. Remple, L. Zunti, M. Bernardin, L. Nightingale-Mercer

"The McClean Lake Mill is located approximately 700 kilometres north of Saskatoon, Saskatchewan, Canada and is operated by AREVA Resources Canada Inc. (AREVA). The mill was designed to process high grade uranium ores, and has been undergoing a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to processing high grade ores from the Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk from hydrogen gas. During 2013 Hatch and AREVA designed and engineered a number of novel upgrades for the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit can be safely operated with ores that can evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project.INTRODUCTION The McClean Lake mill was originally designed to process high grade uranium ores, however until 2014 the average ore grade processed was 1%. The facility has been undergoing a multiyear upgrade and expansion to increase its production capacity from 12 to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to new high grade ores, averaging 18% U, from the Cigar Lake Mine. During the last round of metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit had a higher propensity to generate hydrogen gas during acid leaching than previous test work had indicated. Hydrogen gas is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit."

Jan 1, 2017

By John R. Sullivan, Real Daigneault, Mathieu Piché, Jayanta Guha, Gilles Bouchard

"RESUMELa stratigraphie du camp minier de Matagami se résume a la présence de deux groupes volcaniques: le Groupe du Lac Watson et le Groupe de Wabassee qui le surmonte. Les gisements de sulfures massifs volcanogènes sont situés au sommet du Groupe du Lac Watson. Ces roches sont déformées par l'anticlinal de Galinée dont l'axe, orienté E-W, plonge vers l'ouest. Le cœur de cette structure est occupé par le Complexe de la Rivière Bell.Les roches volcaniques du flanc sud de l'anticlinal sont peu déformées et pendent à 45° vers le sud. Les gites qui s'y trouvent présentent la morphologie typique des gisements de sulfures massifs volcanogènes. Ceux-ci se situent le long d'un horizon repère cherteux et sulfure, appelé ""Tuffite Clef', et leurs cheminées d'altération rejoignent, en profondeur, une zone d'altération stratiforme d'étendue régionale.Les roches du flanc nord ont été transposées tectoniquement en écailles chevauchantes, de dimension kilométrique, a l'intérieur d'un couloir de failles anastomosées d'orientation est-ouest. A l'intérieur: le ce couloir, les gites de sulfures sont déformes et sépares de leur héminée d'altération sous-jacente par des failles.Les gites de sulfures situes sur les deux flancs de l'anticlinal de 'Galinée se seraient mis en place dans un mime environnement volcanique. Leur position stratigraphique est identique puisqu' ils se 'rouvent au sommet de la rhyolite porphyrique du Groupe du Lac Watson. lis se seraient constitués au cours d'une pose volcanique recédant 1'éruption du basalte du Groupe de Wabassee. Le Complexe de la Rivière Bell est perçu comme la source de chaleur responsable de la circulation des fluides hydrothermaux qui sont à ""origine des gisements de sulfures massifs volcanogènes."

Jan 1, 1990

By Jon Errey, Aleksandar Petrovic, Karl Haase

"Developing a gold deposit of this magnitude in the Amazonian jungle of Guyana posed many challenges. This paper describes not only the process & logistical challenges arising from the remote mine site location in a tropical environment with a local industry unaccustomed to recent large scale gold mining operations, but also the innovative technical solutions employed to address the unique ore body characteristics. The best examples of this approach were dealing with the initial high clay content saprolite ore from the development phase and primary mining pits whilst ensuring that the design also implemented the right method to deal with the future fresh rock in an environmentally sensitive habitat. In order to do this separate individual crushing flowsheets were generated, focusing on the specific material handling equipment that would be suitable to handle these various types of material and ensure high recoveries were maintained.INTRODUCTIONAurora gold mine is located in forested region of Guyana, 170 km west of capital Georgetown, and 130 km West North-West of Bartica, a settlement at the junction of the Essequibo and Cuyuni Rivers.The Aurora gold project (Aurora) is a 5,000 tonne per day open-pit/underground operation, which will produce a total of 3.29 million oz. gold – averaging 194,000 oz. per year – over an initial 17 year mine life. At the final investment decision in 2014 Aurora had a total resource of 6.54 million ounces in the measured and indicated categories (62.83 million tonnes at 3.24 g/t Au) as well as additional 1.82 million ounces in the inferred category (16.93 million tonnes at 3.34 g/t Au)."

Jan 1, 2016

The introduction consists of back-ground information, of an historical and statistical nature, relating to the Thompson mine. The geological presentation is based on illustrations that are intended to provide a progressively closer look at the ore occurrence. The illustrations consist of an index map, a geological map of a 15-by 85-mile area including the Thompson mine, a series of four maps dealing with the geophysics and geology of a 6-by 4\f.j-mile area at Thompson, a mine level plan and corresponding section, two sto11e 11lans and corresponding sections, and photo-graphs and photomicrogra11hs of the various one types. T HE Thompson mine is located about 400 miles due north of Winnipeg. The ore deposit was dis-covered in February, 1956. Five years later on March 25, 1961, the Thompson production facilities were officially dedicated with the shearing of the first nickel produced at the Thompson refinery. Full production, at an annual rate of more than 75,000,000 lbs. of refined nickel, was attained later in the year.

Jan 1, 1963

By David Ulrich Furrer

Materials and manufacturing processing technologies have played an important role in the development and capabilities of nearly all manmade products. Market drivers for fuel efficient, low cost, environmentally friendly, more capable transportation has given rise to significant materials challenges and subsequent developments. The rate of improvement and implementation of new commercial products can be limited by the rate of new materials and process technology development and qualification. As many materials are being designed for unique requirements and even location-specific unique properties, the implementation of tools and methods to enable rapid characterization and validation of material definitions and design systems must also be accelerated. A review of new integrated material, manufacturing process and component designs, engineering processes and emerging tools and methods will be discussed. The linkage of computational materials science and engineering into component design will also be discussed along with the challenges and opportunities for further growth and application of integrated computational materials engineering (ICME).

Jan 1, 2015

By W. E. Hale

An area of about 7,000 square miles within the eastern part of the Grenville Sub-province is underlain chiefly by granitic gneisses. There are, however, some exposures of mafic rocks which warrant further investigation, and some attractive structures, particularly basins, which deserve additional economic consideration. T HIS paper describes in a very general fashion the economic and geological features of an area of about 7,000 square miles on the north shore of the Gulf of St. Lawrence in the eastern part of the Grenville Sub-province (Figure 1). The scarcity of published geological data on this part of the Cana-dian Shield (DePuyjalon, 1899 and Longley, 1944) justifies the presentation of these tentative results. It should be appreciated, however, that the information which follows was acquired in a rapid reconnaissance designed specifically to out-line what might be interpreted as favourable geological environments for the occurrence of economic minerals, rather than to produce an authoritative analysis of the geological history of the region.

Jan 1, 1962

By G. M. Ross, J. A. Scott, C. A. Laamanen, H. Shang

"Indirect recovery and use of waste heat contained in smelter off-gas is proposed to expand regions available for year-round, on-site production of micro-algae–sourced biodiesel, a fuel that could be used in underground machinery. A dynamic model of an off-gas heat exchanger describes capture and distribution of heat into open, external, rectangular micro-algae ponds. Smelter off-gas contains sufficient energy to maintain large-scale micro-algae cultivation pond temperatures above 15°C, even with winter ambient temperatures below –15°C. Results highlight opportunities that could lie in tapping these heat resources to produce renewable biofuels on-site and sequester CO2 while leaving the industrial process unaffected.RÉSUMÉ On propose la récupération et l’utilisation indirectes de la chaleur résiduelle contenue dans les dégagements gazeux des fonderies pour développer les régions se prêtant à une production toute l’année durant et sur place de biodiesel à partir de micro-algues, carburant dont on pourrait se servir pour le matériel d’exploitation souterraine. Un modèle dynamique d’échangeur de chaleur contenue dans les dégagements gazeux décrit le captage et la distribution de la chaleur dans des bassins rectangulaires ouverts de micro-algues en extérieur. Les dégagements gazeux des fonderies contiennent suffisamment d’énergie pour maintenir les températures des grands bassins de culture de micro-algues au-delà de 15°C, même avec des températures ambiantes en hiver inférieures à –15°C. Ces résultats soulignent les possibilités que pourrait offrir l’exploitation de ces sources de chaleur pour la production de biocarburants renouvelables sur place et pour la séquestration de CO2 sans que cela n’ait d’incidence sur le procédé industriel.INTRODUCTIONMicro-algae that grow in water can efficiently convertsolar energy and carbon dioxide into biomass. This biomass can be up to 50% oils (lipids), which can be extracted and converted into biodiesel through transesterification (Demirbas, 2008). Compared to terrestrial plants that produce similar oils (e.g., jatropha, soybean, and rapeseed), micro-algae represent an order of magnitude increase in areal productivity, do not require arable land, and can be continuously harvested (Rawat, Ranjith Kumar, Mutanda, & Bux, 2013). The potential advantages through the production of biodiesel from micro-algae also include sequestration of carbon dioxide, reduced reliance on fossil fuels, and the co-production of other value-added bioproducts."

Jan 1, 2017

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

By Chris M. Healey

"Abstract - Perhaps the single most significant variable in the evaluation of a mining project is the reserve estimate. Many parameters are considered when estimating reserves, among them geology. This paper examines the link between the quality of a reserve estimate and a good understanding of the geological controls for the deposit. A clear understanding of the geometry is essential to the accurate definition of the shape and size of the deposit. This includes the definition of any structural controls as well as the proper interpretation of the stratigraphy. Further when the distribution of grades is erratic and there is consequently a high nugget effect, there are significant problems in estimating the true grade of the deposit.Two Saskatchewan examples are presented, one with good knowledge of the controls and therefore good estimates of reserves, and the other with a poor understanding of the geology and resultant problems in deriving good estimates. In both cases the reserve estimates at various stages in the project development are compared to actual results from underground work. The first example is the Star Lake Mine where just about all the estimates were within 10% of the actual on both tonnage and grade. The Laurel Lake deposit is discussed to show how problems in interpreting the geological data make reserve estimation very difficult. Laurel Lake has the additional problem of erratic grade distribution."

Jan 1, 1992

By F. A. Forward

"IntroductionTHE LYNN LAKE MINE, situated in Manitoba about 150 miles north of Sherridon, has been actively developed by Sherritt Gordon Mines, Limited, during the past seven years, resulting in the establishment of a proven reserve of over 14,000,000 tons of ore containing 1.223 per cent nickel, 0.618 per cent copper, and additional cobalt values. For many years, the Sherritt Gordon Company operated a copper-zinc-gold mine at Sherridon but, as this mine was approaching exhaustion and as it was proposed to use the mining and milling equipment to treat the Lynn Lake ore, a number of unusual problems were faced in transferring plant and operations from the one mine to the other, and particularly in preparing to undertake nickel production.Preliminary investigation showed that the ore could be concentrated by flotation to produce a copper concentrate containing 28 to 30 per cent copper with less than 1 per .cent nickel, and a nickel concentrate containing 11 to 14 per cent nickel, 0.3 to 0.4 per cent cobalt, and less than 2 per cent .copper, with high recovery of the three metals in .the concentrates. It was apparent that, initially, the copper concentrate could be economically smelted and refined in the usual manner. But as the nickel concentrate contained an insignificant amount of precious metals (less than 0.02 oz. per ton) and as .it had a much higher nickel content than comparable concentrates normally produced from sulphide ores, the selection of a treatment process and the location of a plant required careful study."

Jan 1, 1953

By R. H. Sheaphim

THE RECENT and continuing activity in the Boundary district, British Columbia, makes the publication of this paper timely. The following description and discussions are based on two years' experience in the district as Field Manager and Geologist for Attwood Copper Mines, Limited. The Attwood project was organized by Dr. D. F. Kidd to re-examine the Boundary mining camp. Thanks are due to Dr. Kidd, both for his intelligent guidance during the project and for his permission to publish this paper. Much of the data and many of the interpretations presented are credited to the work of, and to discussion with, Dr. W. H. White, Consultant Geologist, who worked for two field seasons on the project. However, the author assumes the responsibility for this presentation. Dr. C. D. A. Dahlstrom worked with the author during the latter stages of the project. His assistance and advice are gratefully acknowledged.

Jan 1, 1956

By W H. Poole, E. R. W. Neale

A new style of tectonic map based on age of folding has been prepared for the Canadian Appalachian region as part of the Tectonic Map of Canada Project. This style of map pro-vides a clearer picture of the tectonic history of the region than any meth-od hitherto attempted. Precambrian blocks that were relatively unaffected by Palaeozoic de-formation are distinguished on the Great Northern Peninsula and in the Conception Bay region of Newfound-land. K/ A age determinations suggest that these blocks were intruded and metamorphosed during Grenville orogeny. Other Grenville-like rocks, on Cape Breton Island and in New Brunswick, were more actively involved in subsequent Palaeozoic orogeny. Taconic orogeny, the first phase of Palaeozoic deformation, took place in Middle and/or Late Ordovician time and was accompanied by intrusion of ultrabasic rocks. Evidence of the -

Jan 1, 1961

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

By R. A. Kipp

THE dry concentration of ores and minerals is a subject on which there is very little engineering literature available. With the advent of flotation, practically all milling research was turned to this development as it held the answer to large-scale economic operations. However, there are many concentration problems that can be more adequately and economically handled by the dry methods that have been developed, and, consequently, I believe it is very advisable for mining men to become fully 'conversant with just what can be done in the dry state. Therefore, today, I should like to give a brief summary of the processes that are available and, in a general way, how they can be a p-p lied. I shall confine my remarks mainly to two dry processes: THE Am FLOTA'l'ION TABLE AND THE ELECTROSTATIC SEPARATOR Dry Magnetic Separators should probably also be included, but I am

Jan 1, 1961

By Sub-Committee of the Committee on Research

"THE FOLLOWING REPORT was compiled by a sub-committee of The Metallurgical Society of CIM, Committee for Research, and represents a viewpoint of the steel industry in Canada. The objective was to define those areas in which the industry considers that external sources of Research and Development are a necessary function in supporting the in-house R & D conducted by the industry.On future occasions, the viewpoints of other metallurgical industries, such as those of nickel, copper and aluminum, will be presented. The report is divided into several sections: 1.-R & D Spending by the Steel Industry (a) Memberships in Recognized Steel Research Centres (b) Memberships in Recognized Industry Associations (c) Sponsored Research at Recognized Centres (d) Sponsored Research at Universities(e) Sporadic Research 2.-Areas for Research and Development(a) Instrumentation (b) Environment Control (c) Refractories (d) Sponsored Research at Universities(e) Electric Furnaces (f) Continuous Casting"

Jan 1, 1970

By G. M. Ross, I. M. Ross, J. A. Scott

"The otherwise waste heat in many water streams in the mining industry can be used to provide space heating of adjacent infrastructure including laboratories, workshops, and offices. This can be achieved by using heat pump systems, which can work as a replacement or in conjunction with existing space heating. In the example investigated—process cooling streams at an ore smelter—the analysis provided illustrates that annual heating costs can be 19% lower and a simultaneous 62% reduction in CO2 emissions can be achieved.RÉSUMÉ Dans l’industrie minière, la chaleur qui serait normalement perdue des circuits d’eau pourrait servir à chauffer des structures adjacentes incluant les laboratoires, les ateliers et les bureaux. Cela pourrait se faire en utilisant des systèmes de thermopompes, qui pourraient remplacer ou s’ajouter au chauffage existant. Dans l’exemple étudié, des circuits de refroidissement de procédé à une fonderie, l’analyse fournie illustre qu’il est possible de réduire les coûts annuels de chauffage de 19 % et d’obtenir une réduction simultanée de 62 % des émissions de CO2."

Jan 1, 2016