Search Documents

By Ray Walton, Ron Colquhoun, Ken Thomas, Dwayne Fentie, Barney Burke

"The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources.The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3% year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.BACKGROUNDAs early as 1992, Barrick’s Goldstrike Mine, located north of Carlin, Nevada had indications of the ore becoming ever increasingly carbonaceous in nature. As the open pit and underground exploration programs proceeded to step out over the years that followed, the accumulative amount of carbonaceous refractory ore and tons had become significant. By 1997, 29 million tons of double refractory carbonaceous ore containing an estimated 11.6 million ounces of gold had been identified. By 2000 the resource had increased to 14.3 million ounces."

Jan 1, 2001

By V. Nudo, R. del Villar, A. R. Laplante

"Fine iron ore recovery from the tails of Les Mines Quebec Cartier was investigated using Reichert trays and spirals. The effect of feed rate, density and splitter setting on the performance of rougher, cleaner and recleaner stages of a 2DS tray assembly was determined using 2- and 3- factorial experimental designs. The tray concentrate, assaying 27% Fe, was further upgraded by spiral to yield a concentrate assaying 55% Fe. Further laboratory scale testing showed this material to be easily upgraded to 65-66% Fe with high Fe recoveries.This paper presents the metallurgical results of the three tray stages. The model used to predict the performance of a full recovery circuit is then described. Simulation results are presented and their reliability assessed. Finally, an economic evaluation of the proposed scavenging circuit is summarized.INTRODUCTIONThe Mount Wright plant (UWP), located near Fermont, Quebec, processes daily 130,000-150,000 tonnes of iron ore assaying between 27 and 33% Fe, to upgrade it with three stages of 44.5 cm pitch GEC spirals to 66% Fe, while rejecting approximately 80,000 tonnes assaying between 6 and 11% Fe (1-3). Heavy liquid separation (at 3. 3 g/mL) of the plus 37 µm fraction (+400 mesh) of the tails reveals that a significant fraction of the iron is in the sink product, below 150 pm (100 mesh), as shown in Table 1. Also shown is the iron grade of the sink and float fractions. The high grade of the fine sink indicates that hematite ls well liberated below 105 µm (150 mesh), as previous studies have shown (4,5). The iron grade of the floats is very low in the fine size range, but increases with increasing size above 105 pm, because of incomplete liberation. Overall, two thirds of the plus 37 µm iron ls in the sink product, which constitutes less than 10% of the total tail."

Jan 1, 1987

By P. E. Weidmark

"PART 1-Published PapersAllcott, G.A., and Archibald, D.E.; ""Description of pillar behaviour at Heath Steele Mines""; Can Min Metall Bull; 74:834:80-87; 1981.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of rock Mechanics; 3:32-33; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:37-38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses"" ; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:41; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:42; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:46; 1979.Baar, C.A.; Discussion of Theme 2: ""Tectonophysics""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:60; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3: 116; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:116-117; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:117; 1979.Baar, C.A. '; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:118-119; 1979.Baar, C.A.; Discussions (2) of Theme 4: ""Underground openings""; Proceedings 3rd Congress lntnl Soc of Rock Mechanics; 3:119; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:120-121; 1979."

Jan 1, 1982

By P. A. Riveros

This paper describes the leaching of the common copper minerals tennantite (Cu12As4S13), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4) in acidic media using Fe(SO4)1.5, FeC13 or 02 as oxidizing agents. At temperatures <100°C, tennantite dissolves slowly in Fe(SO4)1.5-H2SO4 media, and the rate is directly proportional to the area of the sized tennantite. The rate increases sharply with increasing temperature and the apparent activation energy is 69 kJ/mol. Increasing Fe(SO4)1.5 concentrations slightly increase the tennantite leaching rate. The kinetics of dissolution of disks of synthetic iron-bearing tetrahedrite in Fe(SO4)1.5-H2SO4 media are linear; the leaching rates are slow but increase significantly with increasing temperature, with an apparent activation energy of 120 kJ/mol. The dissolution of sized particles of natural Ag-bearing tetrahedrite in FeC13- HC1 solutions proceeds according to the shrinking core model, and both Cu and Ag dissolve at about the same rate, provided that the total chloride concentration of the solution is sufficiently high to solubilize the AgC1 reaction product. The leaching rates are slow, and the apparent activation energy is 116 kJ/mol. The addition of sulphate ions to the FeC13-HC1 system reduces the tetrahedrite leaching rate to values similar to those realized in the Fe(SO4)1.5-H2SO4 system. At <100°C, enargite dissolves slowly in either Fe(SO4)1.5 or FeC13 media, and the dissolution rate obeys the shrinking core model. The rate increases with increasing temperature and the apparent activation energies are 50-64 kJ/mol. The rate increases slightly with increasing FeC13 concentrations in 0.3 M HC1 media. The leaching of enargite at elevated temperatures and pressures was also investigated. Potentially useful leaching rates are achieved above 170°C, at which temperature sulphate, rather than sulphur, is produced. Lower temperatures (130-160°C) lead to fast initial leaching rates, but the dissolution of the enargite is incomplete because of the coating of the enargite particles by elemental sulphur.

Jan 1, 2007

By Pim van Geffen, Dave Lawie, James Cleverley

A growing problem facing geoscientists, metallurgists and process engineers is the lack of knowledge transfer between the exploration and production teams. This siloing is generally unintentional, as a typical project may change ownership several times over several decades before it reaches the feasibility and operation stages. Many exploration projects generate vast amounts of high-quality, quantitative data with great spatial resolution, but unfortunately these data are often ignored in subsequent deposit modelling. Instead, deposit models tend to rely on subjective, non-standardized, qualitative classification of geological materials (e.g. rock type, mineral abundance) and processes (e.g. alteration style and intensity), obtained through visual logging of drill core. When projects advance to feasibility studies, the required quantitative data are obtained through expensive metallurgical test work and detailed quantitative mineralogical analysis, such as QEMScan or qXRD. These detailed tests are generally only performed on a small number of large composite samples and the results are extrapolated throughout the deposit, inherently underrepresenting their true variability. Geochemical data obtained during all stages of the project provide comprehensive data coverage at much greater detail and spatial resolution, which allows for the estimation of key metallurgical performance parameters that are required for accurate deposit modelling and domaining.

Jan 1, 2015

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By R. Pakalnis, H. Miller, Madill. T.

"This paper describes a methodical approach to the estimation of the orientation and the magnitude of in-situ stresses. The study was performed at the Ruttan Mine, Sherritt Gordon Mines Ltd. , a 6,000 T.P.D. underground operation, located in northern Manitoba, Canada. It involves an initial estimate to be made based upon: structural interpretation • virgin stress measurements conducted in other areas (world wide, regional)The verification of the prevailing stress regime was made by conducting CSIRO hollow inclusion(1) overcoring measurements. The current cost for a virgin stress determination is about $7000 per measurement(2) and the difficulty encountered in attaining a good reading is high. This paper will describe the analytical procedures employed at Ruttan in evaluating the in-situ stress magnitude and orientation based on three overcore tests. It is proposed to perform an additional six measurements in order to verify the following results:Vertical stress = av (MPa) = 0.027 by depth (m)Major principal stress = o! """" 2.5 xav (340°/-20°)*Intermediate principal stress = a2 - 1.2xav (070°/0°)Minor principal stress = a3 """" o.8xov (160°/-70°)IntroductionThe Ruttan Mine of Sherritt Gordon Mines Ltd., a 6,000 T.P.D. underground operation, is located in northern Manitoba, Canada (Fig. I). The Ruttan copper-zinc orebody is a multi-lensed, steeply dipping (70 degrees) en-echelon deposit. Individual lenses have a maximum strike length of 350 m with widths varying from 7 m to 61 m. The mining method is o pen stoping with delayed backfilling and extends from surface to 860 m below surface."

Jan 1, 1985

By Robin Belley

Outline Introduction Wabush Mines HistoricalBackground Mine and Concentrator at WabushMines High Intensity Magnetic Separators (HIMS) Development of the Manganese Removal Process Pilot Plant Testing Phase Manganese Removal Line 1 Coming Phase: Manganese Removal Line 2 Manganese Concentration Process Development Historical Background 1847: Creation of the Cleveland Iron Company1850: Opening of its first iron ore mine in the Upper Peninsula of Michigan 1965: Beginning of Wabush Mines at Scully Mines, Wabush, Labrador. 1980-1990: Questions raised about how to exploit Scully high Mn Ore (> 2%)Part of the available ore is not saleable due to too high a level of pyrolusite (MnO2) Adding this ore to the resources would be valuable (longer mine life and lower stripping ratio) 1990s: Testwork for Manganese removal Many different processes are studied over more than a decade High Intensity Magnetic Separators (HIMS) are identified as the best technology for Mn removal 2007: Pilot Mn removal line installed Testing carried out through 2007-2008 First Production Line is ordered (2008) 2009: Cleveland Cliffs (now Cliffs Natural Resources)acquire the remaining part of Wabush Mines 2010: Mn Removal Line 1 construction & commissioning Summer 2011: Mn Line 2 Construction

May 1, 2011

By S. Jordanov

The nature of processes that take place on top of copper bearing grains during the suppression of copper acid drainage from mine tailings was studied on a grain model. Cyclic voltammetry (C.V.) was employed as an experimental technique suitable for indirect measuring of copper leaching. Experiments were done in sulfuric acid (pH=2) at electrodes that progressively approach the real situation during acid main drainage, starting with Cu-metal, then with CuO and finally with CuO covered with CaSO4. Oxidation was found to be the only process that takes place on metallic copper electrode anodically polarized up to 2 V vs. Cu/CuSO4 reference electrode. Dissolution is intensive and reaches up to 50 mA.cm-2. When the same was repeated, but on CuO electrode, anodic currents were some 4 times lower than on the bare metallic surface. This indicates that the electrode material is not completely oxidized to copper(II)oxide and the Cu(O) or Cu(I) residues are oxidized during the anodic polarization. This explains the diminished dissolution. Dissolution is further restricted at electrodes covered with CaSO4. It is some 20 times lower than on the bare oxide electrode. When the second layer of CaSO4 was applied, anodic currents were another 15 times lower. Total decrease of anodic currents when transition is made from Cu-metal to CuO covered with 2 layers of CaSO4 reaches up to 7.500 times. C.V. measurements produced a proof that mechanical blockage is the way how lime prevents leaching of copper bearing grains in immobilization experiments referred elsewhere.

Jan 1, 2007

By Jiahao Xu, Namsoo P. Kim, Guikuan Yue

Iron (ferrous ions and ferric ions) plays an important role in the heap leaching of copper sulfide minerals and copper electrowinning. In our previous study, a novel oxidation-reduction potential (ORP) equation only based on the variables of temperature and nominal ferric/ferrous ratio was developed to predict the redox potential of the quaternary H2SO4-Fe2(SO4)3-FeSO4-H2O system, and its applicability was also extended to more complex acidic iron sulfate solutions, especially those generated during the acidic leaching and bioleaching of Printed Circuit Boards (PCBs) to recover copper. In this work, the broader range of applicability of this equation to other complicated acidic iron solutions containing copper ions has been extended and determined. Specifically, synthetic iron-containing solutions with copper ions according to the conditions of industrial electrolyte during copper electrowinning and heap leaching have been used to measure the ORP and test the developed equation. It seems that this equation can still be employed to predict the redox potential of the Fe3+/Fe2+ couple for the simulated solutions under conditions related to copper electrowinning and pregnant leaching solution generated during heap leaching over a wide range of solution concentration, nominal Fe3+/Fe2+ ratio and temperature. It has shown that the prediction and measurement of redox potential is highly useful to estimate and understand the iron chemistry of industrial leaching and electrowinning processes. INTRODUCTION It is well-known that iron (ferric or ferrous) ions are widely involved in the hydrometallurgical production of non-ferrous metals such as Cu, Au and Zn, mainly in the form of acidic iron sulfate solutions. As far as Cu is concerned, in a typical leaching-solvent extraction-electrowinning process, ferric ion plays a central role in the heap leaching process and is reduced to ferrous ions in the pregnant leaching solution. Ferric ion is the most important surrogate oxidant and the dissolved ferric/ferrous couple plays an important catalytic role in accelerating the leaching rate with oxygen as an oxidant (Peters et al., 1986; Schlesinger, King, Sole, & Davenport, 2011). In addition, during the traditional electro-winning process, oxygen is evolved at the anode, and copper is reduced at the cathode. A common idea is that iron in the electrolyte in copper electrowinning cell (with total iron of 1–4.4 g/L) plays an important role in reducing the current efficiency. According to the published results (Winand et al., 1975; Dew et al., 1985; Moats et al., 2009; Khouraibchia et al., 2010), thecurrent efficiency decreases linearly with increasing ferric ion concentration and the energy consumption increase was mainly caused by the decrease in current efficiency.

Jan 1, 2019

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney&apos;s"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d&apos;Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By Adam J. Szladow

"INTRODUCTIONThe low calorific value and the high moisture and ash contents of run-of-mine (r.o.rn.) lignite limits the utilization of Saskatchewan lignites to thermal power plants in Saskatchewan, Manitoba and western Ontario. On the other hand, the low sulphur content and the low mining cost make lignites potentially attractive for new coal markets, if suitable processes can be found for upgrading. Economic upgrading to a higher quality fuel would make lignites more acceptable for industrial and utility boilers.This paper presents a summary of the process engineering evaluation of coal upgrading technologies conducted in support of a study of selected lignite upgrading processes. The summary presents the relative advantages and offers specific comments on the application of coal upgrading technologies for lignites. ResourcesLignite comprises the largest fossil fuel energy deposits in Saskatchewan. The total resources of immediate and future interest exceed 27 billion tonnes. The measured and indicated lignite resources of immediate interest are large enough to last for over 200 years at the current production rate of about 10 million tonnes per year (Table 1).Saskatchewan lignitedeposits are present in three different geologic formations: (I) the Ravenscrag Formation of Paleocene Age in southern Saskatchewan; (2) the Swan River Formation of Lower Cretaceous Age in central north Saskatchewan; and (3) the Judith River Formation of Upper Cretaceous Age in central west Saskatchewan. The deposits in the Swan River and Judith River Formation are not currently of economic interest.The Ravenscrag deposits are confmed to four lignite basins, namely: the Estevan, the Willow Bunch, the Wood Mountain and the Cypress basin (Fig. 1). The estimated resources of immediate interest in the four basins are over 7 billion tonnes (Table I). These resources include lignite seams at least 1.5 m thick, at depths of less than 45 m.The average quality of lignite varies relatively little between the four basins considering the distance between deposits (Table 2). There is, however, a progressive increase in moisture and ash content, and a decrease in calorific value and carbon content as one moves westward from the Estevan to Wood Mountain and Cypress basins. The Estevan area deposits are of higher rank despite the fact that they are stratigraphically younger than the Willow Bunch deposits (Cameron and Marconi, 1979).In upgrading lignite to a higher quality fuel, it is important to know not only the average proximate and ultimate analysis (Table 2) but also other lignite characteristics influencing the product quality . For example, Figure 2 shows the effect of lignite HIC ratio on the product equilibrium moisture for hydrothermal treatment of lignite. It is apparent that lignites with a higher HIC ratio, or high liptinite content yield much better quality product for the same hydrotreatment conditions. Other examples of lignite characteristics which are important in upgrading include distribution of sulphur forms and mineral matter, maceral composition and degree of surface oxidation."

Jan 1, 1989

By J. Dilbeck, J. K. Ratliff, T. Petrov, Z. Brown

"In efforts to improve dust control during deep cut continuous mining a supplemental atomizing spray system, mounted on 14CM15 continuous miner, has been designed and successfully implemented in a U.S. coal mine. The mine is 2.1 m (7-ft) high and uses a blowing curtain face ventilation system with 1.1 m (3.5-ft) curtain offset from the rib. The face ventilation design parameters were set to 9.4 m3/s (20,000-cfm); 4.2 m3/s (9,000-cfm) line curtain flow rate, and 3.8 m3/s (8,000-cfm) scrubber capacity. The performed in-mine measurements, before and after the implementation of the atomizing spray system, showed a significant decrease in the respirable dust levels at the operator place as well as at the return. The paper describes the supplemental water spray system design and performance supported by three-dimensional computational fluid dynamics (CFD) simulations and in-mine test data.INTRODUCTIONThe work on this project have started in 2015 with a study of the conventionally applied face ventilation layouts. The specific behaviour of the face ventilation system have been analyzed trough in-mine measurements and computer modeling of typical cut scenarios. An computer modeling methodology have been developed for estimation the respirable dust concentration (RDC) using tracer gas to RDC contour mapping, calibrated by a single point value, provided by in-mine measurement. Utilizing the results of this study the engineering staff of the mine designed and implemented a supplemental atomizing spray system to improve the dust control during the deep cut continuous mining. Today the atomized spray system is successfully applied demonstrating steady performance and a significant decrease in respirable dust concentration on the working places of the continuous miner (CM) and coal transporters (CT) operators as well as at the return air stream. Information about the applied type of spray nozzles provided by other researchers (Cheng, 1973; Dick et al., 1996; Organiscak & Page, 1998; Pollock & Organiscak, 2007) and spray system manufacturers (Spraying System Co, 2011–2018; Steinen Mfg., 2016) have been used in this project. CFD code and simulation approach validated in a study conducted in 2000-2014 have been applied (Turner et al., 2002; Wala et al., 2004, 2007; Petrov, 2014)."

Jan 1, 2019

By S. U. Baltuch, E. G. Baltuch

"Ventilation in process buildings is key to proper mill function. Correctly engineered systems to evacuate surplus thermal energy from process areas allow optimized rates of air change, thus assuring the good functioning for the lifecycle of the process while demonstrating conformity with occupational hygiene standards. Computational fluid dynamic simulations, coupled with traditional calculations and physical modeling, can demonstrate to end users and assist engineers in the optimization of mill ventilation, reducing total installation costs while assuring that the proper solution is in place for the complete lifecycle of the process equipment. Results have been fully implemented on a number of steel mill and aluminium smelter applications and we continue to study, optimize, and innovate as new tools become available to provide the best possible engineered solutions for particular applications. INTRODUCTIONThe objective of this research project is the development and implementation of modern approaches and computational fluid dynamics (CFD) simulation in the engineering of green ventilation of hot process buildings. This will assure the predictive performance and improve the quality and ease of construction of industrial gravity ventilation equipment, along with the adjunct hot process buildings, while lowering the overall project costs and time to completion.In order for a hot process building, such as a steel mill, to properly function, heat must be extracted from within. This is accomplished by having air inlets at the bottom of the building and outlets at its apex. The reason for this is to maximize the potential chimney effect. When using stack (buoyancy) effect ventilation, the process heat becomes the driver. Therefore, increasing this distance (height) improves the ability of the heated airstream to utilize basic gravity for acceleration of the heat/air flow, allowing a regular number of air changes per hour while ensuring that the process environment remains weather resistant under normal operating conditions.This process has been understood since the time of King Charles I of England, who decreed in 1600 that buildings should have 10 foot ceilings and that windows should be made taller rather than wider to allow better smoke extraction.Figure 1 is a painting of the Bethlehem Steel Works in the 1860s, where the concept of air inlets and penthouses on the roofs for air outlet was already being put into practice. Figure 2 is an early photograph of the Pittsburgh Steel Works."

Jan 1, 2012

By F. Qi, T. Frišcic, C. Mottillo

"One of the principal goals of modern industry is to minimize the environmental impact and increase the materials- and energy-efficiency of transforming raw materials into valuable products. This paper will highlight our latest laboratory-scale research in low-energy, low-solvent reactivity of metal oxides and their conversion into popular metal-organic frameworks (MOFs), zeolitic imidazolate frameworks (e.g. Basolite® Z1200 component ZIF-8), and metallodrugs (e.g. bismuth subsalicylate, active component of Pepto-Bismol®). Mechanochemical ion- and liquid-assisted grinding (ILAG) and ""accelerated aging"" techniques will be presented, along with novel low-energy and solvent-free approaches, inspired by geological weathering processes, for converting metal oxides into metal-organic materials. INTRODUCTIONThe development of environmentally-friendly processes, which would in the same time be more materials- and energy-efficient than the existing ones, is one of the central concerns of modern chemical research. In that sense, the focus of the chemist has been mainly on the preparation of carbon-based organic molecules and adaptation of traditional organic synthesis to the recently delineated ideals of Green Chemistry. However, there is a growing realization within the chemistry community that significant energy, materials, and ecology-related benefits can be achieved and, indeed, targeted in the transformations of materials that are typically associated with inorganic chemistry and minerals processing. The principal aim of this highlight contribution is to illustrate how, through the use of approaches associated with solventfree chemistry and mechanochemistry (James et al., 2012), one can develop a clean and efficient system of chemical and materials transformations involving oxide precursors that normally belong to the realm of inorganic chemistry and mineral processing. In particular, this contribution will provide an overview of the recently developed mechanochemical and solvent-free reactivity of metal oxides towards small organic molecules. These mechanochemical reactions, including the methods of liquid-assisted grinding (LAG, Frišcic & Jones, 2009) and ion- and liquid-assisted grinding (ILAG, Frišcic, 2010), have so far provided a radically different means to construct advanced metal-organic materials (e.g. porous metal-organic frameworks, [MOFs] or metallodrugs) by rehabilitating metal oxides as precursors, eliminating the use of bulk organic solvents, and avoiding the use of high temperatures."

Jan 1, 2012

By Chris Blain

"Abstract - Based upon an extensive database, this paper analyzes the record of modern mineral exploration success and establishes the 50-year trends in discovery. The record clearly shows that the overall discovery rate rose during the 1950s and 1960s, peaked in the 1980s, and fell during the 1980s and 1990s. By commodity and ore-type target, the pattern of discovery is not continuous. Typically, it is episodic as a series of waves with minor resurgence. The waves reflect the order of the so-called discovery booms, led by uranium, then nickel, and copper, polymetallic base metals and gold. With the possible exception of gold, the discovery booms appear to be independent of metal price, although favorable perceptions of the price outlook may well have initiated the boom or led resurgence. Although difficult to quantify, an emerging trend in modern discovery is the integration of several detection techniques into the search process. No doubt, this trend will continue as orebodies become more and more difficult to find. The record of the past two decades shows that greenfield discovery rates have progressively fallen even though the level of investment in exploration has risen to an all-time high. This trend reflects increasing discovery risk. Several factors are contributing to this trend. Perhaps the two most important are: (1) deteriorating economics as increasing real costs and decreasing real prices continue to raise the economic hurdles for minimum acceptable exploration targets, and (2) increasing exploration maturity in many search terrains, particularly those in the traditional regions of North America and Australasia. To succeed cost-effectively in this new environment of increasing discovery risk will require extraordinary creativity, innovation, and technical skill coupled with commercial discipline."

Jan 1, 2000

By Roy O. Ifill, W. Charle Cooper, Alan H. Clark

"A detailed study of the compositional relationships of the Uand Th-bearing minerals in Elliot Lake uranium ores has been conducted, particularly with regard to uranothorite, which clearly plays a critical role in hydrometallurgical processing. Application of the rotating disc progressive-leaching technique to individual mineral grains and intergrowths of known compositions has defined for the first time the solubilization behaviour ofthe minerals in question.In descending order of leachability, regardless of leaching conditions, the phases are: uranothorite, uraninite, and monazite. Inclusions of secondary uranothorite enhance the dissolution kinetics of uraninite, which exhibits a complex dissolution mode. U-rich uranothorite dissolves more readily than Th-rich. Monazite is soluble in HJ)04 and HCI solutions only at temperatures exceeding 85°C. Consequently, it is deduced that the 15% to 20% of thorium not leached from the ore is lost both as monazite and as uranothorite inclusions locked in monazite which persists to the tailings. INTRODUCTIONThe importance of precise information on the mineralogy of ore and gangue constituents for the optimization of metal recovery in hydrometa Uurgical processing has been recognized for some years (e.g. Burkin, 1969), and numerous investigations integrating mineralogical studies and experimental leaching have been reported for ores of gold, nickel, copper and uranium (see summary by Henley, 1983). The complex mineralogy of uranium ores hosted by Precambrian pyritiferous, quartz-pebble, conglomerates has prompted particular attention in this regard (e.g. Liebenberg, 1956; Liebenberg and Taverner, 1958; Feather and Snegg, 1978). In the great majority of documented studies, however, petrographic examination has been followed by bulk leaching, an approach which, although providing valuable information, does not permit precise definition of the evolution of mineral dissolution processes. The authors contend that experimentation involving the step-by-step leaching and mineralogical study of ores is more likely to reveal the actual dissolution events which control the release of metals and, hence, may better define the optimal conditions for hydrometallurgical processing. Such studies (e.g. Hausen, 1983; Horlick et al., 1981) in addition lend themselves to the prediction of changes in the leaching behaviour of ores in which one or more mineralogical feature is subject to modification, a common characteristic of mineral deposits."

Jan 1, 1989

By M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9 m × 2.05 m AG mills (fixed speed) are used in parallel in a dry operation. The performance of AG mills has been lower than the target value indicated by an increase in the product size (P80) from 450 µm (target) to 515 µm and low power draw (50% of nominal). By simulation it was found that increasing the liner lifter face angle from 7 to 30o while keeping the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. When the proposed liners installed in one of the AG mills, the throughput increased by 27%; when 5% (v/v) balls were added the throughput increased by 40%. The product size also decreased from 515 to 501 µm.

Jan 1, 2012

By J. G. Pearson, F. H. MacDougall, A. G. Galley

The difference in age, host rock lithology, alteration and style of mineralization indicates a fundamental difference in the format ion of gold deposits in the Flin Flon and Amisk Lake areas. The Flin Flon area contains early quartz-sulfide-gold veins fo rmed within intermittently active fractures and later plutonic hosted deposits thought to be generated in a porphyry system. In the Amisk Lake area two types of gold occurrences are recognized: I) gold-quartzcarbonate- sulfide veins within or flanking fault zones and 2) structurally and stratigraphical ly controlled zones of dissem inated and vein type sulfide-gold mineralization within extrusive and intrusive rhyolite and dacite porphyries. Both types of deposits are set within supracrustal rocks. are accompanied by intense alteration haloes and were formed prior to the major deformation event suggesting an early, epigenetic hydrothermal origin.

Jan 1, 1986

By Balmer Neilly

Early in my term of office it was announced that my Presidential Address would make particular reference to the subject of Mine Taxation in Canada. With this purpose in view there was drafted a Balance Sheet and Earnings&apos; Statement of a Gold Mining Company. This in turn was submitted to the Dominion Income Tax Authorities in Ottawa and to the Minister of. Mines of each of the several Provinces of Canada. The response to the invitation was not as complete as we had hoped it would be, but the figures that were obtained will be presented during the present meeting, and they constitute, I hope, a sufficient basis for extended study and additional enquiry during the year to come ( 1) . In the form letter that accompanied our request to have the submitted earnings assessed, I made the following assertion: "In this work we have three objects in mind. 1.--We will get direct comparison between the different Provinces in Canada. 2.-We will in this way educate our members concerning taxation as it affects the mining industry. 3.-We will publish the details as to how the assessment is calculated by each body, so that a Mine Manager in the most remote district will have a ready reference to guide him in his annual return to the taxing bodies. As things stand, there is no intention of making this a basis for a critical attack on the present rates assessed. It is intended as an authoritative summary of actual conditions as they presently exist".

Jan 1, 1934