Search Documents

By Nicole Peter

When introducing digital training technology a practical approach helps address cultural concerns.  Solutions to help create acceptance are discussed.  Resistance to change may be deeply rooted in traditional mine training personnel.  Traditional training staff members may consider themselves less digitally-savvy and resist technological methods available to them. A transitional approach intended to help mitigate or resolve resistance is presented as a continuous improvement pathway toward full adoption.  This presentation contends every mine should welcome the benefit of a digitally connected critical enabler.  The adoption of a digitally savvy learning centre is often viewed a disrupter to existing practice.  Given a commitment-driven learning centre model, technology offers the opportunity to transition from a compliance-based training model to one of competence.  Learning and Development practitioners should welcome the latest advances in neuroscience, Bloom’s taxonomy of learning model, and principles which guide mine safety training as outlined by the Lowell Institute for Mineral Resources at the University of Arizona. By employing digital applications to include animation, game-based simulations and immersive Virtual Reality (VR) these technologies create a viable digitally-savvy learning centre. We will outline the ingredients of a digitally enabled, or VR, Learning Centre to offer some observed benefits, successes, and potential short-comings. Much excitement in the industry surrounds implementation of simulation and/or VR headset training.  Given fair consideration of these as a ‘fit-for-purpose’ solution we examine the paradigm shift required to create real results for on-the-job learning.  Interim steps may be needed to meet the cultural transformation.   Simpler forms of VR, in the form of 3D models and VR environments as displayed on a large interactive touch screen, can serve to bridge this challenge and address a group learning environment. Features of the interactive 3D technology and ease of adoption are presented.  Usage of the touch screen is similar to that of a smart phone. It may be implemented as an obvious transitional tool.  To help describe merits of the interactive touch screen the presentation points out these sample underground and surface mine training applications. There are 3-D simulations such as ventilation, emergency response, support installation, and mine cycle and activity scheduling programs. These applications offer the ability to conduct entry examinations, complete digital pre-use checklists, and perform planned task observations in the virtual world of work. The tool may be used to teach the flow of hydraulics and do fault-finding on machinery such as loaders and dump trucks. Learners may navigate in a virtual mining environment to identify hazards, detect and assess abnormal ground conditions, address poor design features, and alleviate traffic constraints. It is possible to use connected physical controls to navigate machinery in the virtual environment. We conclude the presentation with a “compare and contrast” approach to cite potential cultural benefits by adopting a transitional method. 

May 4, 2025

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By G. N. A. Senhorinho, J. A. Scott, C. A. Laamanen

"Closed mine sites are widely regarded as a negative asset due to their legacy of environmental impacts. These sites are often characterized by waterbodies with elevated metal concentrations and low pH that are traditionally considered to have little or no value. These sites are potential sources of beneficial biocompounds produced by microalgae in response to environmental stresses. A bio¬prospecting program found that certain microalgae from waterbodies near historical mine sites exhibited higher antibacterial activity than any microalgae previously reported in the literature. There is potential for the mining industry to be involved in examining features such as tailings ponds at mine sites for high-value compounds, including ones that might help mitigate rapidly growing microbial resistance to current antibiotics. ¦ KEYWORDS Antibacterial, Closed mining sites, Metabolites, Microalgae, Stressed environments RÉSUMÉ Les sites miniers clôturés sont généralement considérés comme des actifs négatifs en raison de leurs répercussions sur l’environnement. On trouve souvent sur ces sites des étendues d’eau affichant de fortes concentrations en métaux et un pH faible, généralement considérées comme ayant peu, voire pas de valeur. Ces sites sont des sources potentielles de biocomposants bénéfiques produits par des microalgues en réponse aux perturbations environnementales. Un programme de bioprospection a permis de déterminer que certaines microalgues trouvées dans ces étendues d’eau à proximité de sites miniers historiques présentaient une activité antibactérienne supérieure à celle mentionnée dans toute la docu¬mentation existante. L’industrie minière pourrait bien participer à l’examen de particularités telles que la recherche de composants à haute valeur dans des bassins de décantation des résidus sur des sites miniers, notamment des composants qui pourraient aider à atténuer l’augmentation rapide de la résistance micro¬bienne aux antibiotiques actuels. ¦ MOTS CLÉS antibactérien, environnements perturbés, métabolites, microalgues, sites miniers clôturésINTRODUCTION The mining industry is one of the largest economic drivers in the world. Within Canada, for example, it contributed 2.8% (C$57.6 billion) of the 2016 gross domestic product (Marshall, 2016). Canada also has the highest non-ferrous exploration budget worldwide (Marshall, 2016); therefore, it is likely that mining operations, mine waste disposal, and the number of closed sites will continue to grow in Canada. The environmental impact of mining operations stems from the volume of tailings produced, which can be up to 97–99% of the total volume of ore processed at a mine (Adiansyah, Rosano, Vink, & Keir, 2015). In 2010, mining was the world’s largest industrial producer of waste at a total of 65 billion tonnes: 51 billion tonnes of waste rock (mine overburden) and 14 billion tonnes of tail¬ings (Jones & Boger, 2012)."

Jan 1, 2019

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By Sydney C. Mifflen

COAL MINING, with its some 15,000 employees, is directly responsible for the livelihood of one-fifth of the population of the Province of Nova Scotia and indirectly so for that of possibly another fifth. Deposits of coal are known and worked in four counties of the Province, from which is being produced yearly tonnages as noted below: Cumberland County 750,000 tons Piccou County 400,000 tons Inverness County 100,000 tons Cape Breton County 5,250,000 tons TOTAL FOR NOVA SCOTIA 6,500,000 tons Production in Cape Breton county is entirely from the one source, the Sydney coalfield, and not only is this field the most important in respect to output, as is disclosed above, but it is also the largest presently known deposit in the Province and holds the greatest tonnage yet in reserve for future mining. In the light of the above more or less generally known facts, it is trite to remark on the importance of the Sydney coalfield in the internal economy of the Province. On the other hand, not nearly as well-known nor as frankly recognized is its significance in the national life of Canada, for from this field is produced not only 80 per cent of the Nova Scotia coal but over 40 per cent of all coal mined in the Dominion. Another noteworthy comparison can be made from the fact that the Sydney field contributes 22 per cent of all the bituminous coal consumed in Canada, the remainder being made up of 7 per cent mined elsewhere in Nova Scotia, 27 per cent from other parts of Canada (British Columbia and Alberta, principally), while the remaining 44 per cent is imported, practically wholly, from the United States of America.

Jan 1, 1941

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By Mike Dry, Mani Manimaran, Mykolas Gladkovas, Mariam Melashvili, Chris Fleming

Development of a new hydrometallurgical flowsheet requires quantitative description and optimisation of all chemical processes in each step in the process, as well as mass and energy balances across a fully integrated circuit incorporating all the unit operations. This paper covers steps leading to early modelling of a gold processing plant based on a bromine/bromide lixiviant. Research conducted at SGS Lakefield in collaboration with Albemarle provided the data that were used in the development of this model. A previous investigation in this series described the leaching behaviour of various mineral types in Stabilized Bromine reagent. This paper is concerned with the gold recovery operations associated with a conceptual bromine leaching process. The recovery of gold by different types of resin and activated carbon was studied, along with various methods of stripping the gold from the extractant. The circuit is closed by electrolysing the spent leach liquor to oxidize some of the contained bromide back to bromine that would allow recycling the regenerated leach solution back to the leach step in the process.

Jan 1, 2015

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch

An advanced laboratory-scale weathering apparatus has been developed at McGill University to study the effects of weathering (ambient temperature oxidation) on the self-heating of sulphides. Previous work by the authors has shown that the problematic self-heating of sulphides is inherently linked to the degree of oxidation (weathering) of the minerals: un-oxidized active sulphides exhibit little or no self-heating while the same material when weathered can generate extensive self-heating bringing temperatures well above 100 0C. In this study the effects of environmental conditions (weathering time, ambient temperature, sample moisture, relative humidity, and oxygen content) were evaluated with respect to the self-heating response of a pentlandite-pyrrhotite nickel sulphide concentrate.

Jan 1, 2015

By L. Kilburn

A survey of 281 mineral exploration agreements examines the ratios among three ways that may be used to purchase an interest in a mineral property, viz: pay cash, pay shams and make future expenditures on the property. The dollar value of the future expenditures exceeds that of cash or shams by about nine times in most of the 110 agreements that contain cash-expenditure or share-expenditure components. Results suggest that cash and shams are treated about the same in terms of value. Buyers and sellers haw opposing priorities for the way that they prefer to purchase a mineral property. These opposing priorities should give rise to a perceived 50:50 balance between cash/share payment and future expenditures to satisfy the idealized situation described by most definitions of fair market value (FMV). This balance between cash/share payments and future expenditures appears to be rationalized in negotiations to a FMV when expenditures are nine times greater than cash and/or payments. On this basis, it is proposed that the FMV of a property may be determined by aggregating the dollar amount of the cash/share payments plus one-ninth the dollar value of future expenditures, as set forth in the respective purchase agreement, and proportionately applying such aggregate to full property value.

Nov 1, 2005

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By L. Tong

The nickel laterite ore is composed of soft and hard minerals, and nickel distributes preferentially into the soft mineral rather than in the hard. Selective comminution of saprolitic and goethitic nickel laterites is investigated to upgrade nickel into the fine fraction using stirred milling. The optimal selective grinding conditions were determined through a kinetic study and the limit of selective grinding and nickel upgrade was analyzed. The breakage rates of minerals, grinding time, and the weight ratio of soft and hard minerals in the feed play an important role in selective grinding. A small breakage rate on hard minerals and a large breakage rate difference between the minerals are optimum for selective grinding. The soft mineral grade decreases with grinding time and the optimum grinding time is a trade-off of the soft mineral upgrade and recovery. The minerals weight ratio determines the limit of selective grinding. The effect of nickel upgrade is determined by both the conditions that influence selective comminution and the nickel grades in both the soft and hard minerals. The nickel grade in the soft mineral determines the limit of nickel upgrade.

Jan 1, 2015

By Y. Wang, S. Liu, K. Jiang

China is the world’s largest producer and consumer of non-ferrous metals. In recent years, significant progress has been made in research and commercial application of pressure leaching technology to produce some nonferrous metals. Research and development activities include a low-pressure, low-temperature leaching technology for complex copper concentrates, a hematite process to treat pressure leach solutions from zinc concentrates, and a pressure leaching - solvent extraction process for molybdenum and rhenium. Examples of commercial practices include a two-stage pressure leach technology in a zinc plant in Danxia, a direct leaching technology in a zinc plant in Zhuzhou, a high pressure acid leaching process for a nickel laterite project in RAMU, and a pressure leaching technology to treat arsenic sulfides in a plant in Guixi. The development of pressure leaching technology for the recovery of lead, vanadium, gallium, germanium, and precious metals in China will also be described in this paper.

Jan 1, 2015

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003

By M. W. Lewis

A mine's inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine ’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By Alan R. Holt

"This paper provides an overview of the use of uranium and coal in Ontario Hydro's generation program. The dynamics of available supply sources including mining and transportation infrastructures and regional considerations are described. Included is a discussion of needed procurement strategies, both in place and planned, to meet fluctuating fuel requirements while ensuring adequate supply security and cost effectiveness. IntroductionDuring the first half of this century, Ontario Hydro or the Hydro Electric Power Commission of Ontario, as it was then known substantially supplied all of the province's electricity needs from a large number of hydraulic generating stations. Although hydraulic power still provides a very significant part of Ontario energy requirements, this paper will concentrate on the role of uranium and coal in their generation program. To provide a perspective on the importance of these two fuels, Figure I shows the approximate value of each for the past few years in relation to Hydro's total operating costs. The trend toward increasing nuclear output and a corresponding decline in coal use is also clearly illustrated.Figure 2 shows the currently installed capacity of their three main energy sources, hydraulic, nuclear and coal and the 1986 production totals for each, followed by Table I which compares the average operating or running cost on the basis of dollars per megawatt hour for each type of plant. It demonstrates dramatically why Ontario Hydro base load s its hydraulic and nuclear plants, and why coal has become the swing fuel on the system. Although they have a 1200 megawatt plant in Toronto with natural gas-burning capability, and a 2000 megawatt oil-fired station near Kingston, both are presently mothballed and have not been considered in this paper.This paper starts with a user's perspective of the nuclear fuel supply situation which will be discussed in relation to the usual considerations of security, flexibility and cost."

Jan 1, 1988

By Roger V. Pierce

IN the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centred upon haulage, hoisting equipment, mill flow-sheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materials. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain orebodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered orebodies are moving rapidly from stopes to reduction plants-because it is now possible to develop an orebody and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials o mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining.

Jan 1, 1943

By H. J. Chalmers

THE H.B. MINE and concentrator are located in the Nelson Mining Division of British Columbia, on the north side of the Sheep Creek valley about seven miles southeast of the town of Salmo. It is an operation of The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), which has its metallurgical plants at Trail, about 25 miles west. The property was originally staked about 1907 by Horton and Benson, whose names are commemorated in the designation "H. B." Up until 1927, a considerable amount of development work was done in the upper levels by various companies. Cominco purchased the ?property in 1927 and carried out intermittent work until 1946. Following this, an extensive surface diamond drilling programme and a subsequent underground exploration were undertaken. Sufficient ore was outlined 'to warrant the construction of a 1,000: ton concentrator. This was started in April, 1952, and completed by the spring of 1953. However, because of adverse base metal market conditions, operation was deferred until May, 1955.

Jan 1, 1957

The integration of mining and mineral processing technologies into new advanced mining systems is considered to offer several benefits, including selective mining, reduction in waste, increased productivity, flexibility, and improved resource utilization. This paper focuses on underground hardrock mining and the integration of pre-concentration technologies into future mining systems as representing realistic, shorter-term integration options. Control of fragmentation to optimize grinding, pre-concentration of ores, in situ leaching, and modular mining/mineral processing systems are possible with existing technology. Current research is directed toward development of integrated underground systems that minimize surface activity and minimize or eliminate surface waste disposal. Results from a simulation model of an integrated underground pre-concentration system are presented.

Jan 1, 2002

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002

By Adam Moore, Ryan Gillespie, Jarrett Quinn, Audrey Walters, Peter Radziszewski

"Vale Long Harbour Processing Plant (LHPP) was designed to process Voisey’s Bay nickel concentrate into finished nickel and associated copper and cobalt products. The plant includes a secondary grinding circuit comprising two Stirred Media Detritors (SMDs) operating in parallel. The ultrafine grinding circuit was designed to process concentrate at a rate of 33 t/h and produce a ground product (P80) of 20 µm to feed the leach circuits. Start-up of the grinding circuit at LHPP was undertaken in December 2014.The objective of this paper will be to describe the design, commissioning, start-up and performance of the secondary grinding circuit with a focus on the two Metso SMD-355-C mills. Following a brief overview of Vale’s LHPP and the SMD technology, the paper will review the design of the SMD secondary grinding circuit from lab tests through to scale-up performance prediction. This will be followed by the results of circuit commissioning outlining some of the issues raised and addressed after which SMD performance will be outlined. Specifically, the SMD circuit grinding performance will be examined since start-up which will include the effect of media size and wear on grinding. Furthermore, impeller wear will be examined by determining initial “shear volume” and worn “shear volume” as well as its effect on mill power and the means to maintain it. The paper closes with a discussion on grinding performance."

Jan 1, 2016