Search Documents

The Charters Towers 1:250 000 Gravity Data Set represents a new initiative of the Department of Resource Industries (DRI, formerly Queensland Department of Mines) to provide high quality regional gravity data over areas of the State that have high potential for new mineral discoveries. The Department has adopted a strategy to upgrade geophysical data to complement the ongoing Regional Geological Mapping Program (RGMP) of this Department and in areas where the data would be of most benefit to the mineral exploration industry. Part of this strategy is to ensure that these data are released within 6 months of data collection.The 1989 Charters Towers survey was completed as a joint project with the Bureau of Mineral Resources, Geology and Geophysics (BMR), and is the first regional geophysical data acquisition project undertaken by the DRI. Prior to this survey, the only gravity data in this area dates from the B MR regional surveys carried out between 1960 and 1967.

Jan 1, 1990

By C M. Côte, P Bolz, L Pagliero, M Edraki, M Shaygan, P Erskine

Mines in Queensland must now prepare a Progressive Rehabilitation and Closure (PRC) plan, with the requirement to justify the selection of the post-mining land use (PMLU) for each rehabilitation domain. Given that there are nearly 200 mines who must undertake a comprehensive PMLU assessment, there is a need to develop methods that will minimise the duplication of effort. As part of a broader initiative on innovative post-mining land use planning, this project undertook a regional analysis of the technical suitability of several PMLUs.

Aug 2, 2023

By D Stephenson, N R. Steward

“TerraFlowingTM” is a dewatering process that addresses both the value proposition of Tailings as a Resource™, and the safe storage of tailings. “TerraFlowingTM” incorporates two stages of cyclone dewatering followed by centrifugation of the final dilute tailings stream. In this process three dewatered tailings streams are produced; a primary cyclone underflow, a secondary cyclone underflow and a centrifuge pulp. These three streams can be combined, or used, in various configurations to achieve different outcomes. The ability to vary the cyclone and centrifuge operations and configuration enables this process to deal with tailings feed variations in particle size distribution and mineralogy and deliver consistency, or design variations, in particle size distribution, tailings solids concentrations and recoveries. Water recovery can be up to 85% of the total water in the tailings with a stackable final tailings product achieved if the three tailings streams are combined in the maximum solids concentration configuration. The primary cyclone can be operated to deliver a particle size distribution suitable for tailings storage facility embankment construction or alternatives such as concrete structures or shotcrete for support. The secondary cyclone underflow and centrifuge pulp is suitable for beaching deposition within the tailings storage facility.

Jul 1, 2021

By Simes C. D

Results of experiments for dissolution of zinc by aeration of sphalerite in glass, copper, galvanised iron and stainless steel vessels of identical dimensions are reported. It was found that in a glass container dissolution of zinc reaches a maximum after 30 min aeration and then decreases whereas in the copper container dissolution remains nearly unchanged up to 30 min aeration and then increases. In the cases of galvanised iron and stainless steel containers zinc dissolution increased steadily with time up to 60 min aeration. It is suggested that the different rates of dissolution in glass and copper containers may be due to electro-chemical actions.

Jan 1, 1984

What is the best circuit to comminute primary crusher product to make beneficiation feed? Finding the best circuit to crush and grind minerals to beneficiation sizes is a complex problem that can lead to interminable discussion. Conclusions reached can be questioned. This will continue as long as the technology of comminution continues to expand, and is a mixture of many technical and economic factors in what is not a precise science. Laboratory and pilot plant procedures now exist that can help process engineers make sound decisions on which circuits are the best for crushing and grinding the specific ore being studied. It is the aim of this paper to discuss such procedures so a better under- standing of key decision parameters is avail- able, and to update comminution testing which has seen a. period of change in which new procedures have been introduced.

Jan 1, 1978

By H Bleuler

A new portal and access drift was constructed by Concrete Constructions for BHPÆs Elouera Colliery, south of Wollongong.The portal area at the base of the Illawarra Escarpment is in soft colluvium material, underlain by highly to moderately weathered sandstone. The area has a well documented history of slope movement or slope creep and one of the main criteria for the design was to minimise disturbance to the unstable slope by limiting the excavation for the portal establishment. This was achieved by incorporating a sloped headwall and gabion wingwalls to accommodate the anticipated creep and groundwater seepage.Main features of the design process also included the provision of both primary and secondary support in a single shell application and the use of canopy tubes to provide support ahead of the tunnel face.The active involvement of the designer during the construction phase and the flexibility of the design concept allowed changes to the support methodology to be carried out as excavation proceeded.This paper describes the design process undertaken for portal establishment and access drift to cater for the variability of the exposed ground conditions along the drift alignment.

Jan 1, 1999

By D McInnes

Rather than look at the problems associated with sampling, this paper deals with the issue of sampling and blending to optimise revenue û predominantly in the mining industry. An example of the use of this methodology in the agriculture industry is also presented. Mining companies, in particular, are experiencing a boom in commodity prices and many believe the industry is in the middle of a æsuper cycleÆ. Production levels are being escalated dramatically to meet the demand coming from China and India. This in turn has further stretched the capacity of our rail and port infrastructure û resulting in significant shipping queues around most Australian commercial ports and increased demurrage costs for the producers. Mining companies are now looking for effective scheduling, planning and blending to maximise production and reduce demurrage charges û given the current infrastructure constraints. Mining companies can no longer use spreadsheets to run their business. This paper further looks at how these outcomes can be met by optimised blending using an integrated supply chain management system such as MineTrak together with effective sampling and analysis.

Jan 1, 2005

A practical approach has been developed for the design of both grates and pulp lifters. It is based on: an appreciation of the process interaction between grates and pulp lifters, an interpretation of mill charge structure as it relates to discharge through grates, and an analysis of pulp and solids flow in pulp lifter channels. This approach can be used to improve the overall discharge effectiveness of AG and SAG mills.

Jan 1, 2000

Safety bulletins and stickers issued for the paste backfill plant at Cannington read as follows: æCannington Paste Fill Plant, First of ItÆs Kind in AustraliaÆ. We could even dare to state that the Cannington plant is different than any other paste backfill plant in the world because of the overall design, plant equipment and underground delivery. However, one thing to be certain of is, the paste backfill plant works as designed and a pump is not required to deliver paste underground given the general plant arrangement at Cannington. The past two years have been a process of evolution to design and construct the plant and make it work. This paper will describe the paste process using full mill tails along with placement of cemented paste underground. Discussions will include rationale of fixed plant selection along with various control requirements. BHP World Minerals recently commissioned its paste backfill plant in December 1997. Cannington is placing full mill tails underground via two surface boreholes that deliver either to primary or secondary stopes.

Jan 1, 1998

By Runge IC

The mine planning process is reviewed and appropriate software considered in terms of "line process" or "support function". The mine planner's requirements of a geological model and the elements of and requirements of a computerised mine planning system are all discussed. The use of "support" software for mine planning is considered and general rules for its development are given. Important changes involved in implementing a computerised mine planning program are listed.

Jan 1, 1983

By Meakins R. L, Talaska A, Kenny D, Haycraft J. A, Dickson B. L

A vehicle-mounted radiation detector interfaced to a microprocessor called PRAM (programmable radioactive analyser mobile) has been developed to provide grade control for selective mining of a soft rock uranium ore. The grade of ore over which the vehicle passes is determined and indicated by several coloured lights to a pegman who walks behind the vehicle. Coloured pegs are then laid out to mark the uranium grade ranges on the floor of the mine pit. Comparison between grade ranges determined by the PRAM and by prior drilling and downhole logging at the Yeelirrie deposit, Western Australia indicate good agreement. Use of the PRAM decreases the cost, manpower and time required to grade extensive areas of a mine pit floor.

Jan 1, 1982

Mount Isa Mines Limited has been mining silver-lead-zinc ore at Isa Mine for 60 years. Mining methods have evolved continuously, and current production rates of 4.7 Mt/yr are obtained from a combination of sublevel open stopping, cut and fill, and benching methods. In the near future, orebodies mineable by open stoping will be gradually depleted, and the relatively new benching method will be further refmed to replace cut and fill methods wherever possible.

Jan 1, 1993

"DEEPHOLE " or "Longhole" drilling is the name given to the drilling of prospecting holes with the pneumatic hammer drill. The drilling bit is of the same form, and is prepared in the same way as ordinary rock drill steel, and is extended to the bottom of the hole by sectional hollow rods, through which water is forced.The cuttings from the hole provide a sample of the ground drilled.Deephole drilling was developed at an American mine where the cost of diamond drilling, owing to loss of diamonds, was excessive, and proved very successful, holes being drilled as deep as 220 ft., in limestone, at a cost of one dollar per foot. The use of the method in other mines, and in a variety of rocks, has since been described in the technical literature. From the published descriptions the following data are drawn:

Jan 1, 1930

Major changes occurred in the management of loss prevention and risk management at operations in North and South America due to increased insurance premiums following the Olympic Dam fire in Australia in 2001. There are many different scenarios on how fires can develop and the estimated maximum losses (EML) those fires can incur. The EML is utilised by insurance companies to determine the cost of insurance premiums. The cost of insurance can be controlled at existing and newly designed solvent extraction (SX) plants by using risk reduction methods and design criteria to limit the fire exposure. A review of data collected during several loss prevention risk assessments can show how a budget can be protected from dramatically increased premiums and see which design of SX plant and fire protection standards best apply to your operations. The paper will investigate the pitfalls of existing materials of construction, capacity, geography, management practices, fire risk minimisation, and fire suppression systems. Intelligent engineering and managerial improvements implemented by the operations in the Americas in the past two years have further minimised the fire potential and benefited companies in insurance renewal negotiations.

Jan 1, 2003

By Paine G

Kidston Gold Mines commenced mining in 1984 and currently mine approximately 10 million tonnes per annum of ore and waste using a conventional truck and shovel open pit method. The overall mine grade is a low 1.82 grams per tonne.The mineralisation is generally uniform within the ore zones and mining boundaries are staked out from blasthole assays according to pre-determined cut-off grades. Buffer blasting is necessary to minimise post-blast lateral movement of in-situ grade for digging control.The characteristics of the rock currently mined vary widely from soft oxidised to hard unweathered rocks. Blasting problems have been experienced during the initial mining phase in these harder rocks.

Jan 1, 1986

By Bowra N

Working capital is best described as money that must be supplied from a company's treasury to buy inventories for raw materials and finished products and to provide credit to customers who have not yet paid for delivered products. Working Capital requirements for resource projects are to a large extent, dependent on specific characteristics of the projects concerned. Important variables are the nature of the project and speed with which sales can be realised. The project's location is also important as this will influence inventory levels. Working capital requirements have a time profile, the present value of which can represent a significant portion of a projects overall capital needs. A significant component of a project's working capital is not readily recoverable or able to be reassigned should the project fail or be deferred.

Jan 1, 1986

By Rynn J. M W, Paynter A

Recent studies by the authors have concerned themselves with assessing the earthquake risk to north-eastern Australia, based on available historical earthquake data for the area. There have been several significant earthquakes (Richter local magnitudes of the order of 6) concentrated in the Wide Bay - Burnett region in central eastern Queensland, although none of these has occurred close to a significant centre of population or development. Using derived average acceleration attenuation relations and world-wide data on earthquake-induced damage as a basis, conditions under which earthquake-induced liquefaction may occur have been investigated and presented in graphical form. Historical earthquake data for north-eastern Australia have been overlain on this graphical presentation and it has been demonstrated that the Wide Bay - Burnett region, in particular, may in the past have been on the verge of earthquake-induced liquefaction, where ground conditions are susceptible. When this is viewed in the context of the rapid growth in population and development in this area over recent years, the risk can no longer be ignored with impunity.

Jan 1, 1990

By I Haine, J Penm, T Waring

During 1999 there was a considerable turnaround in world prices for most minerals and energy commodities, except for the bulk commodities (coal and iron ore). The main reasons for this turnaround were: improved prospects in demand for most minerals and energy commodities in the Asian region following a return to both economic and industrial production growth in key economies in that region; continued moderate growth in demand in Europe and North America; substantial production cutbacks in a range of minerals and energy industries; effective reductions in the supply of oil by OPEC nations; and an announcement by European central banks that they would cap the amount of gold they sell and loan in the next five years. Most of these influences are expected to be sustained into the first years of the new millennium. In 2000, with exception of coal, average world prices of minerals and metals are forecast to rise significantly. Gross domestic product and industrial production is expected to grow in some European countries and most Asian countries in 2000 and, with moderate growth expected to be sustained in the United States, demand for minerals and energy is expected to increase. AustraliaÆs main bulk commodities, iron ore and coal, saw prices set for 1999 - 2000 at substantially lower levels in negotiations in early-1999. Double digit price cuts were locked in. However, similar falls appear to have been avoided for coal in Japanese Fiscal Year 2001, while increases of between four and six per cent were achieved for iron ore. Forecast modest recovery in economic growth in Japan and increasing demand elsewhere in Asia are expected to lead to tighter market conditions in 2000. Beyond 2000, world minerals and energy markets will be influenced by the expected robust global supply responses of minerals and energy companies, against a background of sustained economic growth and industrial production growth in major consuming countries. Over the medium-term, a return to declining real prices which have been evident for most commodities in the recent past, is expected as exploration, mining and processing technological change and associated productivity growth continues to reduce industry costs. While lower rates of exploration and mining investment in Australia between 1998 and 2000 will modestly constrain the rate of future industry expansion, Australia remains an important contributor to expected growth in global minerals supply over the medium-term. Australian mine production is forecast to grow between 1999 - 2000 and 2004 - 05, boosted by production from recently commissioned mines and minerals processing facilities and comissioning of other projects at advanced stages of planning.

Jan 1, 2000

By C Sennersten, A Hellicar, C Lindley

Traditional methods of resource modelling and mine planning rely upon geostatistical methods applied to exploration drill core data to derive a three dimensional model of the distribution of metal grades, quantised into rectangular prisms or blocks. The resulting block model is a primary input into short, medium and long term mine planning. However, block attributes are averaged or interpolated over a complete block, meaning that information at smaller scales is lost to the mine planning process. Grade engineering for new mining methods, such as the development of more accurately controlled blast designs, continuous miners for hard rock and sensors for rock properties that can be distributed along the operations process and value chain, allows excavation to be much more selective than traditional blasting, and provides data for driving earlier separation of waste from ore. This selectivity can be optimised if the resolution of resource models can match or exceed the spatial resolution of selective mining technologies. Opportunities for selective mining increase as a deposit becomes more heterogeneous. This leads to an interest in methods for estimating the distribution and characteristics of mineral heterogeneity within the ore-body. The objective of this work is to present some definitions of mineral heterogeneity, and to explore how heterogeneity as defined can be measured and inferred within ore-bodies.CITATION: Hellicar, A, Sennersten, C, Lindley, C and Evans, B, 2018. Heterogeneity assessment for grade engineering in complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 11–13 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Powered support plays a major role in longwall mining and improper selection may lead to a disaster. While different countries follow different norms, a universal approach is needed to be developed. For this purpose, a computer program C-ALPS

Jan 1, 1998