Search Documents

The central thickened discharge system of tailings disposal takes advantage of the natural beach slope formed by sub-aerially discharged tailings, and the non-segregating properties of thickened tailings, to create a homogeneous conical stack. The need for containing embankments can be largely avoided leading to capital and operating cost savings. Methods for estimating beach slopes and tailings density, essential parameters for the design of such a system, are described. Case histories from three mining operations are used to illustrate the application of the technique, There are also seen to be potential advantages in the areas of water management, seepage, and rehabilitation. Laboratory and in-situ testing enable parameters to be determined.

Jan 1, 1991

The cost of constantly extending a decline tunnel that plays a part in the actual extractive process is a revenue cost. The characteristics of such a decline tunnel are that it is dug in a series of relatively small excavations. It follows the ore body and is dug as close to the ore body as practicable. In addition, the decline allows for the extraction of ore in the immediate vicinity, with the ore being extracted in a relatively short period of time.

Jan 1, 1990

Diamond drilling was first carried out at Norseman in the Princess Royal Mine, early in this century. Little concentl'ated drilling was done from then until Western Mining Corporation commenced drilling in 1934. Since then Central Norseman Gold Corporation N.L. has continually employed diamond drilling in exploration of the field. After 1946 the advantage was seen of applying broad pattern surface drilling at Norseman in the reef exploration. In 1953, as a result of the steeply rising cost of drilling and the time taken to penetrate surface material by light equipment, heavier drills and new rigs were introduced. The surface drilling programmes called for a greater monthly or annual footage and to satisfy this new techniques were introduced. The Mitchell-21 machines were discarded and A-3000 machines were installed, firstly under a 48 ft. fixed tower, then mounted on a truck with a 20 ft. tower, and finally on a truck carrying a 40 ft. tower. With the mobile units a compressed air compressor is attached. By use of compressed air with either the Reed roller or Hawthorne bit, rate of penetration of overburden is greatly increased. The mobility of the truck mounted machines has greatly reduced the time required to move from one hole to another, and the use of heavier machines on a three shift per day basis has considerably increased the footage per shift. The general result is an increase to 1,500 ft. of drilling per month per machine, while costs have been greatly reduced in spite of increased wages and diamond prices.The underground drilling technique is described. Analysis of performance has not been made because the drillers performance is subject to shaft routine and service.INTRODUCTIONGold was first discovered at Dundas in 1894, and at Norseman, 14 miles north, in 1895. From that tirpe until 1935 mining activity fluctuated. Following the mining revival in 1935, production in the field has remained comparatively stable. This stability in part has been due to the broader scale of operations of Central Norseman Gold Corporation N.L., and in these operations diamond drilling has played an increasingly important role.

Jan 1, 1956

By Larsen E. R

We discuss the concept of optimal cut-off grade policies and their advantages in terms of maximisation of net present value of mining operations. There are indications, however, that such optimal policies are not widely used in the mining industry. In order to explore why this is the case we identify a number of stakeholders who may have diverging interests in the operating policies of a given mine. These various interests are mapped and a number of important relationships are explored in a large qualitative systems dyanmics model.

Jan 1, 1995

By Coombes J, Richards W. L

The objective of this paper is to illustrate, in a practical way, how both geologists and mining engineers can use conditional simulation to add value to their decisions. Inherent assumptions, requirements and essential components of condition

Jan 1, 1998

EARLY HISTORYIt is 91 years since the epic discovery of gold at the eastern end of Kalgoorlie's main street appropriately named Hannan's Street after the prospector who found the first gold here on17 June, 1893.The Spirit that motivated the early prospectors in their search for gold in this thirsty sun-burned land, unmapped, uncompromising and difficult is characteristic of gold prospectors the world over. Conditions have changed since then substituting comparative comfort for previous austerity and privation, but the quest-ing spirit, the everlasting optimism, the perseverance in the face of frustration .and disappointment still exists.It exists with the prospector who more often than not is a company geologist; it exists with the shareholder enjoying through his investment a vicarious participation in this wonderful, exciting industry and not the least with those people who have chosen the goldmining industry as their career.

Jan 1, 1984

The paper reviews recent valuations of mineral properties, many of which are at an early stage of exploration. The various methods used are outlined. The problem of comparing, in terms of whether it is fair and reasonable, a highly subjective opinion of the present value of a portfolio of exploration tenements with a vendor consideration, the real value of which, in most cases, lies at some indeterminate time in the future because of the application by the Australian Stock Exchange (ASX) of escrow conditions, is highlighted. Examples are given of some of the questionable logic used by consultants in handling this difficult issue. A proposal for revision to current flotation and listing practice which, the author believes, would circumvent the problem and at the same time provide better protection for the investing public is offered for Consideration.

Jan 1, 1994

By G L. Boyd

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal recovered by highwall mining methods.

Jan 1, 1998

Two examples of risk assessment and risk management in action are discussed. The first is in a management context in relation to Kingsgate Consolidated LtdÆs Chatree operation in Thailand. Kingsgate has conducted an over-riding risk management program to assess and manage risk across its complete business from the Sydney and Bangkok offices through to the Chatree Mine and the companyÆs exploration group. This example addresses how Kingsgate has applied risk management, particularly to the process operation, and the benefits that have been gained. The second is in an operational context in relation to Minara Resources LtdÆs Murrin Murrin operation in Western Australia. The subject is the methodology and outcomes of a risk assessment across the Murrin Murrin operation specifically to identify and assess risks with potential impacts from $1 M to $7 M. This section of the paper then shows how the outcomes of the risk assessment were integrated into MinaraÆs strategic plan to debottleneck the plant and increase nickel production.

Jan 1, 2004

Financial theory often takes some time to penetrate industry and when it does it can result in a paradigm shift in valuations and mental models. The Black Scholes option valuation was first published in 1973, although the authors were only awarded a Nobel Prize in 1997. The valuation of real options has been applied to the oil and gas industry for some time, however it has only recently been more widely applied to the non-oil, mineral resource sector. The use of real option valuation (ROV) for the valuation of marginal and short mine life resource projects is a more useful valuation tool than the conventional DCF, NPV valuation tool. The application of ROV has major implications for corporate strategy. It generally favours equity over debt funding and non-hedging over hedging. A retrospective assessment of the successful development of the Lennard Shelf Operations demonstrates the concepts of implementing real options and the value destruction of limiting operational flexibility through debt and hedging activities.

Jan 1, 2003

By Weimin F

In the last decade, great strides have been made in the raise boring technique in China. Extensively, the drilling and blasting method has been replaced by the mechanized raising method since 1980. There are now over 3C raise drills operating in more than 20 mines. The diameters for shaft boring varies from 500mm to 2000mm, and to depths up to 90m. Tlis paper mainly describes the performance, mtLin technical achievments and applications of all four kinds of raise drills, and auxiliary equipment. Finally, some recommend- ations for future improvement in the raise boring technique are presented also.

Jan 1, 1987

By Forssberg E

This paper presents the experimental results on the effects of slurry Theology on ultra-fine grinding by a stirred ball mill. The amount of dispersant, slurry density and the particle size were selected as the parameters. The viscosity of dolomite-water slurry was measured by rotational viscometers. It was found that by adding enough dispersant, the effect of particle size from 1 to 10 pm on the slurry theology could be eliminated, but a strong effect of slurry density (tested for a range of 65 to 75 wt per cent) remained. The use of dispersant transformed the slurry from Bingham plastic flow to dilatant flow, which reduced the yield stress to zero, but increased the viscosity at higher shear rates. During the milling process, the viscosity was stable. The yield stress, however, increased suddenly from zero after a certain milling time. The mill operation stopped at the point where the yield stress increased due to poor slurry fluidity. The milling efficiency was found to be higher at a lower amount of dispersant addition or a lower slurry density within the experimental limits.

Jan 1, 1993

HISTORY OF PROCESS DEVELOPMENT The manufacture of coke from coal commenced at the beginning of the 17th century by heaping coal into circular mounds in the open, covering with earth, clay or ash and slowly burning the coal in the mounds to produce a heap of coke. Naturally the process was slow in production rate with low coke recovery due to the loss of that part of the coal which was completely burnt to ash. As a natural consequence of this initial carbonisation method, a coke oven design was developed so that the coking chamber, which was constructed of brick, was circular in plan, cylindrical in section with a dome shaped roof - similar in shape to the original coal mounds. As the shape of the chamber was similar to the old dome shaped beehive, the ovens were called beehive ovens. The ovens were built in long single or double rows with retaining walls between each oven and as such were known as a battery of beehive coke ovens. In these early beehive ovens, coal was charged from hand wheeled tubs into a hole into the top of each oven, hand- levelled with a rake and the oven side opening sealed with bricks and clay except for some small holes in the opening to admit limited quantity of air for combustion. Coking commenced by the heat retained in the brickwork from the previous charge. The gases evolved from the coal, together with the admitted air, were partially burnt inside the oven to supply the heat for carbonisation and the surplus gases were burnt to waste at the top charging hole. The heat from this gaseous combustion inside the oven together with the reflected heat from the brickwork of the arched roof of the oven allowed carbonisation of the coal charge to proceed from its surface slowly downwards to the floor of the oven. At the end of the coking cycle (usually 4 or 5 days) when there was no more evolution of gases, as indicated by diminishing gas flame and a drop in oven temperature, the brickwork of the oven opening was removed. The coke was then quenched by inserting a pipe with spray holes to spray water over the coke charge in the oven after which the coke was raked from the oven. The work of charging and levelling the coal, bricking and removal of oven opening, quenching and raking out the coke all required manual labour. As these ovens only carbonised a 5 to 7 ton charge of coal per cycle of 4 to 5 days, to produce 3 to 41/2 ton of marketable coke, the labour required per ton of coke was high.

Jan 1, 1975

Detailed studies of mineral paragenesis, isotope and trace-element geochemistry, and physical mineralogy at Mount Morgan are compatible with deductions by Geopeko Ltd geologists concerning field relationships in the mine area. Considered together, field and laboratory data suggest that the Mount Morgan deposit originated from a shallow, intrusive, acid volcanic dome similar to those which produced the Kuroko-type deposits in Japan. At Mount Morgan, however, interaction with sea water was much less, the sulphides were concentrated rather than forming a group of deposits, and only the throat of a breccia vent is pre- served, so that only the lowermost parts of Kuroko-type deposits can be compared with the Mount Morgan mine. A final difference lies in the presence at Mount Morgan of a quartz diorite adjacent to the ore. Mineralogical data are compatible with post-ore intrusion, possibly up an earlier volcanic fissure.

Jan 1, 1974

A number of mines in Australia have experienced premature detonations caused by bulk explosives reacting with the rock type being blasted. Premature detonations are extremely high risk events as they are unplanned, occurring at any place, at any time, potentially resulting in high loss (personnel and equipment). Many Australian mines have also experienced spontaneous combustion where spilt explosive reacts vigorously with the rock type. Premature detonation in these cases does not occur due to the lack of confinement and the volume of explosive present, but these reactions could impinge on the surface initiation system and provide an early warning of future premature detonations. The explosive ground reactivity phenomena is not restricted to Australia with similar incidents being reported in North and South America, South Africa, China and South East Asia. All reported incidents have two common denominators, being the presence of sulphide rock types and nitrate based explosives. Both premature detonation and spontaneous combustion result from the same series of reactions of partially weathered sulphides that ultimately result in the violent decomposition of the ammonium nitrate based explosive. A number of relatively easily observable indicators can be used to assess a particular minesiteÆs potential for explosive ground reactivity. The presence of two or more of these indicators means that minesite personnel should contact their explosives manufacturer for assistance in determining if a problem exists and if so then developing strategies to overcome the situation. The paper describes the indicators as well as discussing, via a case study, the holistic approach required to efficiently develop a relevant æSafe and Efficient Blasting ProcedureÆ to deal with explosive ground reactivity problems.

Jan 1, 1999

By Singer RP

The Latrobe Valley brown coal deposits are one of Australia's major energy resources with measured and indicated reserves amounting to some 162 billion tonnes. Economically recoverable reserves are estimated at some 65 billion tonnes, 47 billion tonnes of which are classified as available for mining (VBCC (1983)). These deposits contain one of the lowest grade fuels used anywhere in the world. Typical Net Wet Specific Energy values range from 6 to 9 MJ/kg. Despite the low energy value of the raw coal, the Latrobe Valley deposits represent approximately 90% of Victoria's indigenous non-renewable energy resources. Utilisation of this vast primary energy resource has been a key factor in the economic development of Victoria.

Jan 1, 1990

The Australian Mineral Industry has to compete on world markets, so its mineral research has to be aware of overseas developments, it must be of world class, and it must utilise as many ideas as possible in order to solve those problems that uniquely affect Australian minerals processing. North American mineral and resource research may be taken as a guide to world government, industrial, contract, and entrepreneurial research trends and ideas. A number of interesting findings are noted that may guide Australian developments and strategies for the future, in minerals research and exploitation.

Jan 1, 1986

Since the introduction of the Neil George Five Point Safety System, to the underground sections of The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines in March, 1969, the Disabling Injury Frequency Rate has been halved and shows signs of contin- uing to fall. The total accident frequency rate has also fallen, although the decrease has not been as significant. Before the introduction of the Neil George Safety System, analyses of the direct causes of accidents showed that approx- imately 25 per cent were caused by "unsafe conditions", while 75 per cent were attribu- table to "unsafe acts". Within twelve months of introducing the system, these percentages had significantly changed to 7 per cent unsafe conditions and 93 per cent unsafe acts. Today, the figures are 3 per cent and 97 per cent respectively, and these figures clearly show that the main emphasis in the current programme must be directed towards making the operating men safety conscious. The effort must be focused on changing the minds of men.

Jan 1, 1975

The recommendations of a recent American report on "Better contracting for Underground Construction" are considered in relation to Contracting practices on major Australian projects by representatives Of the "classical trilogy" - the Owner, Engineer and Contractor.

Jan 1, 1976

By Jin C, Shi X

The studies of pulp electrochemical flotation separation of pyrite and arsenopyrite were made from the thermodynamics, mineral natural oxidation rate, property of mineral surface oxidised material and pulp electrochemical flotation tests. The results showed that although pyrite and arsenopyrite possessed similar thermodynamic stability, significant differences of two minerals were observed in natural oxidation rate, property of surface oxidised material and its influence to dixanthogen formation on the oxidised mineral surface. Based on the non-thermodynamic differences, the pulp electrochemical flotation technology was successfully used to separate arsenopyrite from pyrite in pilot test.

Jan 1, 1993