Search Documents

By Miovski P, Hooft P. V

In the majority of recently commissioned gold mines granular activated carbon is used to adsorb gold from alkaline cyanide pulps or solutions. At the same time the carbon also adsorbs many other inorganic and organic species, most of which lower the activity of the carbon. Removal of these foulants is necessary before the carbon is reactivated and recycled. Standard practice for re- storing carbon activity involves high temperature treatment in a kiln - an apparently straightforward unit operation which is not always satisfactorily carried out. This paper presents the results of some fundamental work carried out on the thermal reactivation of carbon in a laboratory rotating pot kiln. The effects of temperature and steam addition on carbon activity were examined and compared with the activity of carbons obtained from a number of commercial kilns. Carbon was also reactivated using a small-scale Rintoul Furnace in which carbon was resistively heated by the direct passage of an alternating electric current. It was established that both elevated temperatures and the addition of steam to hot carbon generally enhanced its activity although peat-based extruded carbons responded a little differently to coconut shell types. Other measurements made included the weight loss and the hardness of carbons as a function of reactivation conditions.

Jan 1, 1987

The paper describes the geology, structure, stress, gas and strata geomechanical properties for Leichhardt Colliery and their reactions to mining.

Jan 1, 1986

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

In general, modern mining companies all over the world have to face the same economic circumstances as any other part of the industry: considering the tough competition, production and haulage costs must be reduced permanently whereas productivity has to increase substantially in order to remain price-competitive. However, the imposed pressure also offers the chance for consideration of alternative mining concepts, the application of which can result in substantial cost savings and improvements in the quality of the mined material. As one of these alternative mining concepts, surface mining technology offers substantial improvements in productivity. It also influences aspects of haulage, such as safety and speed, in a positive way. The capability of selective mining ties in nicely with the production of small-sized crushed material, the granulometry of which allows the elimination of the primary crusher. Mine operators profit from reduced costs for the maintenance of their haulage vehicles due to reduced wear, a decreased likelihood of accidents and higher average transport speeds. Surface Miners can also be used to cut haul roads into virgin rocks and leave a clean and level surface behind, improving the quality of these created roads. Thus, it is even possible to use ordinary road trucks for transport in mines. The current paper outlines in detail the effects of the surface mining technology on mining and haulage aspects and reports on applications where substantial cost savings could be achieved due to the application of what is also referred to as æsimple mining processÆ.

Jan 1, 2003

The excavation of a tunnel through rock and mixed ground of basalt and silty clays presents a challenge to engineering organisations. Such was the situation facing the Melbourne and Metropolitan Board of Works (MMBW) in constructing the 15.3 km, 5.5m dia. tunnel component of the new Western Trunk Sewerage System. The tunnel geology showed that there were two distinct components to the excavation - rock and mixed ground. By drawing on extensive experience in the use of Tunnel Boring Machines (TBM's) used previously by the MMBW and using techniques developed for predicting TBM per- formance, a comparison of the options of drill and blast versus TBM was made. The conclusion was that TBM methods would provide the best solution to the problem. Tenders were called for the supply of a TBM. A performance specification was used to attract tenders offering designs which re- flected the state of the art on an internation- al level. Particular features required by the MMBW were included in the specification. The excavation planning and operation are described in this paper. The production achieved has shown that the TBM can very adequately handle rock excavation (best weekly production 167.9m). Extreme conditions of mixed ground with heavy groundwater inflows have been handled using an auxiliary thrust system to maintain gripper reaction through the soft ground encountered.

Jan 1, 1987

By Morland R

Recent influence of backfill stability on stope production in the Copper Mine at Mount Isa Mines Limited is described. Changes to the mining process to improve fill stability are described, including increased focus on fill performance, modifications to extraction techniques, increased fill quality, changes to drill and blast practice, and research into backfill stability. Several case studies are described.

Jan 1, 1995

As a result of cheap Maui gas and plentiful hydro-electricity, over the past few decades New Zealand has enjoyed some of the cheapest energy of any OECD country. The situation is changing; at best we are facing some radical changes in energy use, at worst we are facing a crisis resulting from the following:   Cause 1: Maui gas will be exhausted by 2012. Distorted pricing and supply contracts; resulted in Huntly Power Station, a coal mine mouth generator running on 70 per cent Maui gas until very recently!   Cause 2: Investment in new generating capacity (and transmission) is woefully inadequate; as a result hydro lake levels are being continually pushed to the limits.   Cause 3: Distorted thinking is everywhere, for example; æWe will find more cheap gasÆ. æGas is clean û coal is dirtyÆ. Hot air  û ægreen alternatives such as wind generation will save usÆ. æNo NuclearÆ. The outcomes of the distorted thinking will be price increases, then shortages (there is nothing like "black-outs" to focus national thinking) and finally recession.   But what can NZ do? - Mine Coal. Coal jump-started the industrial revolution, it can provide the transition to post-gas and oil. NZ has the second highest reserves of coal per capita in the world, yet we use less that any other country with significant coal reserves. Our exports of our best coal have increased threefold, yet out own consumption has remained static at about 1-1.5 Mtpa for the last 30 years. Our coal is NZ owned and inexpensive relative to other energy sources, even allowing for infrastructure and environmental costs.   What can we do? We as mining professionals can promote informed responsible development and investment in the country's mining and energy business. We can galvanise public opinion on issues such as æunbundlingÆ our entire energy chain from mine-to generator-through transmission, even if the nuclear issue has to wait! With oil above US$70/bbl substitution is feasible. For individuals, there is always solar!

Jan 1, 2006

By Mackenzie W. R, Harding C. G

The Islamic Republic of Mauritania is a large country of over 1 000 000 square kilometres situated on the Atlantic coast of north-west Africa. It is bounded to the north by Western Sahara and Algeria, to the east by Mali, and to the south by Mali and Senegal. With the exception of a narrow strip in the south along the Senegal River valley, the country lies entirely within the Sahara. The north of the country is largely devoid of vegetation, and it is estimated that 90 per cent of the population of 2.1 million people live in the southern quarter of the country. From about the turn of the century, Mauritania was ruled by the French from Dakar in Senegal and, until 1960 when it obtained independence from the French, Mauritania did not have a capital. Today, the capital is Nouakchott, home to an estimated 600 000 Moors of mixed Arab, Berber and African descent. After independence in 1960, disputes over Spanish Sahara to the north led to a military coup in 1978 and it was not until 1991 that a democratic constitution was adopted. The new constitution declares Mauritania to be an `Islamic, African, and Arab Republic.' It provides for an executive president, elected for a six-year term, and for a bicameral legislature, consisting of a national assembly and a senate. The first presidential and legislative elections were held in 1992 under United Nations' supervision. Mauritania's economy is predominantly pastoral, and the country depends heavily on foreign aid. Its principal export industries are iron ore mining (about ten million tonnes per annum from mines near Fderik in the north) and fishing. Mines d'Or d'Akjoujt SA (MORAK), a company in which General Gold Resources NL (GGR) has 42.5 per cent equity, produces over 50 000 ounces of gold per annum, which represents the third largest export industry in the country.

Jan 1, 1996

By M Chiquito, R Castedo, P Segarra, L M. López, J A. Sanchidrián, J Navarro

The aim of this work is to assess the performance of different constructive solutions against explosions on the strength of masonry walls. The solutions tested, namely an external metal mesh, a glass fibre film on the external face of the wall and a basalt fibre film located on the inner face of the wall, have low to medium cost and are originally designed for other purposes, like seismic protection. Four cubic boxes 3 × 3 × 3 m were built using each of the solutions and typical masonry blocks. In the tests, a spherical plastic explosive initiated in the centre was placed at scaled distance of 2.9 m/kg1/3, so that moderate damage would be caused on the wall. In order to assess the performance of the explosive, pressure gauges were placed at the wall and at different distances from the explosion. Additionally, vibrations were monitored with seismographs in the far field and a high-speed camera was used to estimate the shock wave velocity during the tests. The resulting damage has been evaluated on 13 points of the external wall of each box using a rebound hammer. Damage maps have been drawn for each wall based on these measurements and damage has been assessed inside the box considering the fragments mass launched during the test. The use of external metal mess leads to a decrease of 34 per cent on damage of the external wall and 38 per cent reduction of spalling. The use of a film in the inner wall provides a strong reduction on spalling.CITATION:López, L M, Segarra, P, Castedo, R, Sanchidrián, J A, Navarro, J, Santos, A P and Chiquito, M, 2015. Performance of different constructive solutions against explosions in full-scale masonry walls, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 819–824 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

The Vera Nancy orebodies, although simple in overall geometry, are in detail generally narrow, multi-veined and fluctuating in width, strike and dip. Tight geological control is required to optimise gold and silver production from this bench stoping operation. The processes used to model the resource and to control ore drive development have evolved since mining commenced in 1997. Grade control is a combination of orebody sampling, geological data collection, understanding orebody geometry and the optimisation of ore driving and stoping activities. Global resource modelling utilises mainly drill hole data which is largely superceded by drive development data as stope development progresses. The orebody has a relatively low nugget effect that assists in grade estimation. Rather than rely on sophisticated grade interpolation methods, resource estimation to-date has focussed on developing the geological understanding of the orebody to ensure the framework for estimation is correct. Drill data alone is not adequate to define deposit geometry for stoping . Drive data is used as the dominant data set for stope geology modelling once development for a stope is complete.

Jan 1, 2000

By J Ralston, W Skinner, D Fornasiero

The Wark has been conducting collaborative research through the AMIRA International P260 series of projects for over 20 years. This paper reviews specific outcomes of successful technology transfer to flotation plant practice over that time. Moreover, findings of an independent audit of industry users of the research outcomes of the P260 project are reviewed. The key to successful technology transfer is the active engagement of industry personnel at all phases of the technology transfer process. Other research outcomes include the novel application of new measurement tools and methodologies which include, for example, advanced surface analysis techniques. These new tools and methodologies have been pivotal to improving our understanding of factors that limit the flotation separation of minerals at plant scale. Future potential targets for technology transfer to improve flotation plant practice are discussed.

Jan 1, 2009

It is possible from simple gas behavioral theories to develop more complex relationships which allow prediction of transport phenomena such as diffusivity and viscosity of gas mixtures. Such physical data can be used in engineering calculations for both bulk gas movement and gaseous chemical species movement. Both of these are important in the solution of mines ventilation systems. There are specific limits of flammibili!'y of some common mines gases.

Jan 1, 1983

By May P. M

The role of chemical speciation in alkaline cyanide solutions is discussed by reference to recent experimental data from the authors' laboratories. It is shown that serious gaps exist in our present knowledge of the thermodynamics of cyanide complexes in solution. Nevertheless, using the available data and the JESS suite of computer programs it has been possible to develop a simplified chemical speciation model for alkaline cyanide solutions under conditions relevant to the gold extraction process. Some possible implications of the model for plant operations are Discussed.

Jan 1, 1991

By Williams P. A

Tailings dams constructed by the upstream method have traditionally been built using the sand fraction of the tailings, which has automatically provided a relatively permeable embankment material, and helped provide the necessary drainage conditions which are a pre-requisite for safe and stable dam construction using this method. This paper discusses some recent trends which have resulted in proposals to use impermeable material in place of the sand fraction as the embankment material, both for the starter dam, and subsequent lifts. The consequences of these types of decisions on the overall stability of the dam are illustrated, and the need for continued monitoring of pore pressures in the tailings as the dam is raised is emphasised.

Jan 1, 1992

By Hodkinson I, Slight M

Over the last five years Mt Leyshon has matured into a sizeable gold mine by Australian Standards. In the later part of 1990, after commissioning of the 3.5 mtpa CIP Plant upgrade, experience indicated there was potentially additional Mill capacity beyond that being utilised at the 3.5 mtpa rate. Overall throughput was limited by crushing plant performance and high operating costs resulting from the age and condition of the main crushing plant.In addition, mining was being carried out using a mining contractor who utilised relatively small, high cost mining equipment, and on-going exploration success was also indicating that the then current mine plan would result in only a portion of the available resource being exploited.

Jan 1, 1992

Gold bearing sediments at Scotland Point occur within the Quaternary Gibbston Fonnation, which underlies Cromwell Flat in Central Otago. Gibbston Fonnation unconformably overlies Teniary Manuherikia Group clays, sands and quartzose gravels. Gibbston Formation sediments are composed of a texturally diverse, multistoried lithostratigraphic succession of sandy/gravelly/bouldery lithofacies, deposited within a multiple channel (braided) depositional environment. Lithostatigraphic analysis indicate an upward overall decrease in average grain size, reflecting a concomitant reduction in stream competence. This trend results from progressive channel abandonment as major distributaries avulse across the outwash plain. Grade distribution of alluvial gold is controlled by aggradational and to a lesser extent degradational lithofacies deposited as distinctive braid bar forms near the base of the sequence. These lithofacies were deposited at different topographical levels on the outwash apron, under variable hydraulic conditions. Recognition of large-scale auriferous bedforms within the braid bar depositional system coupled with an understanding of lateral facies relationships, allows headgrade control on run of mine ore and quick determination of overburden to ore ratios.

Jan 1, 1988

By Dunne R, Defilippi J

Dump leaching began at Teller in late-1988 at a rate of 4 MTPA and has been progressively expanded to the present rate of 10 MTPA. Teller's on-going commitment to dump leaching is driven by the amenability of gold ores to the process and the availability of large tonnages of low grade gold ore. The sequence of evaluating ores for dump leaching involves rolling bottle tests on coarsely ground ore, followed by small and large column leaching and finally trial heaps. Trial heap tests are very expensive and an alternative approach to this is large diameter column leaching.A four-column permanent facility was built at Teller to specifically evaluate the leaching characteristics of new dump leach ores. Details of construction, operation and dismantling are discussed in the paper. Capital cost for the four column facility was some $45 940, while operating costs are about $24 800 per column.

Jan 1, 1992

By Radmuller H

The proposed underground mine at Porgera forms an integral part of the Porgera Joint Venture project in Enga Province in the remote Highlands of Papua New Guinea. The total in-situ reserves are approaching 400 tonnes of gold making the Porgera deposit one of the largest in the world. The remote, rugged and inhospitable terrain, recent unstable geological environment and primitive yet socially complex nature of the densely populated local community, combine to make the Porgera project very different to developing mines in Australia. The Porgera project is a challenging and exciting mining exploration venture in the final stages of feasibility study submission and negotiations with the National Government of Papua New Guinea. A 1476 m exploration adit was driven in the footwall of the high grade mineralisation for diamond drilling purposes as part of the evaluations necessary for the feasibility study. Ground conditions encountered have ranged from weak mudstones with high water content, requiring immediate steel set support, to competent intrusives.

Jan 1, 1988

By Pease JD

This paper reviews the changes in operating practices made in the heavy medium plant to meet the objectives of increased silver, lead and zinc production at lower operating cost. The effects of medium quality, screen- ing efficiency, medium consumption, equipment service life and plant availability on these objectives are described.

Jan 1, 1988