Search Documents

The combustion characteristics of Australian coals which contain high inertinite have been studied in a laboratory drop tube furnace and a Thermogravimetric Analyser. The pyrolysis chars and combustion residues were microscopically characterised using a modified coal petrography technique. Results indicated that the overall burnout of inertinite-rich Australian coals under pulverised fuel combustion conditions could be generally within a range of 97 - 99 per cent burnout. The studies showed that poor coal burnout cannot be generally related to high inertinite content in the Australian coals. The extent of coal burnout varies from coal to coal and vitrinite as well as inertinite may contribute to the unbumt chars in combustion residues. Combustion conditions had greater influence over char formation and coal burnout than the coal properties. However, under similar pf combustion conditions, coal rank and coal maceral composition had a strong influence over the coal combustion behaviours and final coal burnout. Simple correlations using coal properties may be used but with caution to determine coal volatile release and burnout at high temperature and rapid heating conditions.

Jan 1, 1991

By Enga B. E

Following considerable laboratory studies concerning diesel particulate control systems for underground use, a Canadian program was initiated to implement practical, real-life systems. This program covers the application in seven mines throughout Canada, of a particulate control system, to 14 engine models from four engine manufacturers in 18 different vehicle types, for a total of 23 vehicles. Partially funded by the Canadian National Research Council (NRC), this program required detailed analysis of operating cycles, maintenance variabilities and installation problems. This paper summarizes the work carried out to date to define real-world targets and the success achieved so far in attaining practical underground particulate control.

Jan 1, 1988

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

By Thuli AJ

Copper concentrate from Bougainville's copper mine located on the west slope of the Crown Prince Range on Bougainville island, is pumped 27 km to the filter and drying plant at Anewa Bay for preparation and storage prior to shipment to overseas customers. Prior to shipment the thickened concentrate slurry is passed through a test loop to check that its consistency and pH are acceptable for transportation through the main pipe line. The Bougainville pipe line is unique since it is the world's first copper concentrate system. where slurry is pumped an appreciable distance against a high head,

Jan 1, 1975

The importance of the minerals industry to Australia is briefly reviewed and the professional specialists essential for the industry identified. The average first degree graduation numbers in geoscience, mining engineering, metallurgy/materials and chemical engineering are shown and compared with the postgraduate numbers. Demographic trends in population are reviewed and the implications for the required numbers of trained specialists indicated. Short/medium and long-term possible solutions to potential shortages of trained personnel are canvassed.

Jan 1, 1997

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operations at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry.Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle ize distributions and brightness values have been prepared.Extensive drilling and bulk sampling of the deposit over eight years has shown that the orebody is large and of a high grade suitable for the production of premium quality coating kaolins.The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW).The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment, the nature of the production process and details the project management procedure used for the design, construction and commissioning of the plant. Three areas of significant interest, the gas turbine fired pray dryer, the moving bridge shiploader and the use of aerobelt conveyors on the project are detailed.

Jan 1, 1988

Instantaneous outbursts have occurred at Metropolitan Colliery from the pick and shovel work of early days to the modern mining techniques of today. Developments have been the introduction of an emission index to measure the proneness of the coal to outbursts, drainage and destressing by large diameter holes, attempts at higher productivity by the introduction of pulsed infusion shotfiring and improvements in ventilation. The future plans and aims for the Colliery include prediction of outbursts, seam gas pre- drainage and longwall mining.

Jan 1, 1980

By Mike Sharwood

This subject is to be discussed in greater depth by Mike Sharwood. It has also been the subject of a mini-symposium by the Melbourne Branch of the AusIMM in October, 1993. The papers from this symposium were distributed to the membership late last year "to raise their consciousness and to promote greater awareness and understanding of the wide range of liabilities that may arise". An introductory paper by Nicholson outlined the many areas in which liability may arise with particular emphasis on expert reports, eg: Takeovers Schemes of arrangement Acquisitions from associates Prospectuses Related party transactions Directors' duties Continuous disclosure Other influences (environmental, occupational health and safety, trade practices)

Jan 1, 1994

By Shining Z

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores, as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

The purpose, basic data requirements and various analysis/modelling tools employed for geomechanical evaluation of mine-site conditions are overviewed. The impact and application of computer technology are dis- cussed. Broad guidelines and criteria are presented for establishment of a practical geomechanics data-base system to yield infor- mation suitable for mine design purposes. Future needs of the Australian mining in- dustry are examined.

Jan 1, 1983

Production of refined zinc (99.95 per cent) at the minesite without increasing greenhouse gas emissions is considered. As an example, exploitation of the full reserve of the McArthur River orebody is proposed, using the existing concentrator, whilst introducing radically innovative smelting technology. Bulk flotation of all the sulphide minerals is followed by smelting in a melt circulation reactor with tonnage oxygen. By smelting the high-energy pyritic concentrate and reacting the evolved sulphur dioxide with near-mine dolomite, a large amount of electricity can be generated. This is enough to supply all the requirements for the smelter itself, an air separation plant and a facility for compressing and liquefying carbon dioxide. Carbon dioxide is disposed of off-shore for enhanced oil recovery or by other means. The reacted dolomite fixes sulphur as an inert and environmentally acceptable solid residue. Treatment by these means leads to virtually zero gas emission smelting. The paper concludes with a vision for the future in which expansion of zinc smelting capacity is seen to be definitely needed.

Jan 1, 1998

By Turner T. M, Jorgensen F. R A

The tendency of the concentrate to ignite was studied using four techniques, namely, laminar flow furnace, fluid bed, thermal analysis and boat-in-furnace. Exothermic activity occurred at two temperatures: minor activity in the vicinity of 200¦C, major activity at 330-350¦C. The low temperature reaction was due to the ignition of a small amount of free sulphur while the major activity was associated with the ignition of the sulphide minerals, notably pyrite. To avoid ignition of the sulphide minerals, the gas temperature should not exceed 300¦C and the oxygen content of the gas phase should be as low as possible. It was shown that little of the arsenic in the concentrate entered the gas phase during drying.

Jan 1, 1987

This paper describes how Western Mining Corporation uses sophisticated diesel equipment in mining of shallow flat dipping narrow ore- bodies in the Otter Juan area. Though in most cases the stoping method chosen relies on hand held conventional equip- ment, the 'ore handling systems have been designed to allow for a relatively high degree of mechanization. The use of diesel loaders, trucks along with three boom jumbos is described. A single one in nine decline driven as the means of access to the various ore surfaces at Otter/Juan resulted in the first ore being produced first 15 weeks after the first round was fired in the Ore-Decline. Now, three years later, the.mine is in full production, and in 1971/72 produced 392,000 dry tonnes of high grade Nickel Ore.

Jan 1, 1973

By S Planeta

The use of explosives in underground mining has its drawbacks, particularly in the case of thin or narrow vein type deposits. Due to that, there is a need to develop more discriminative and safe rock-breaking technologies. Mechanical rock splitting seems to be one of the most promising avenues in this respect. This paper describes briefly principles and features of radial-axial splitters. It reviews a feasibility study done to evaluate a potential of this technology in selective mining. It was intended to compare productivity and cost of ædrill-splitÆ mining with conventional cut-and-fill method. Hypotheses and assumptions adopted, methodology used and the obtained results are presented and discussed. The study has confirmed an interesting potential of radial-axial splitters in mining thin and narrow vein deposits. In conclusion, it is stressed however, that it will take more R&D work to corroborate the results obtained. Some suggestions concerning future research in this field are also given.

Jan 1, 2003

By Brasnett TC

A wide variety of problems are encountered on a day to day operating basis in the Isa Mine Concentrators. These vary from complex textural problems in the lead-zinc concentrator and their subsequent effect on grinding and flotation to scheduling of converter slag treatment in a chalcopyrite concentrator. With the advent of process control, metallurgists need to specialise and keep up to date with technology improvements. This paper will attempt to describe the significant problems'faced by a Metallurgist û Control.

Jan 1, 1978

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By Terry G. A B

Before detailed design of Museum Station could commence, a number of factors had to be considered to determine its exact location within the city street pattern, the depth and the dimensions of the underground station. To arrive at a sound con- clusion regarding location, the relationship of the station to probable future city development had also to be considered.

Jan 1, 1981

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

By Koppe J. C, Costa J. F C L

This paper compares different results for overburden volume estimation assisted by geoestatistics, particularly using kriging methods. The main goal is to obtain the most reliable digital terrain model for the calculation of the overburden volume. The data was collected on an irregularly spaced grid and interpolated values were calculated to provide a denser, more regular data set before volume estimation. The field work was developed at the Butia-Leste Coal Mine, southern most Brazil, where an accurate survey was done using a total station theodolite with electronic data collector. The study was developed in five main steps: data acquisition, exploratory data analysis, spatial continuity measurements, point and block kriging estimation and verification of the results. Data acquisition was carried out on a 5 x 5 in grid. This dense grid provides an exhaustive data set of the real terrain against which data subsets can be compared for the various interpolation procedures and volume calculation. This provides an interesting insight into the influence of the number of data on the estimation error. Univariate statistics were used to compare each data subset and the exhaustive dataset. Ordinary kriging on the data subsets followed by contouring was carried out using Geoeas and Surfer software respectively. A subroutine written in C provided the link between the files generated in Geoeas and subsequent contouring routines embedded into the Surfer package. Omnidirectional and directional variograms were modelled defining the parameters for kriging estimation using Geoeas. Different variogram models were checked through cross validation prior to kriging. A comparison between the magnitude of the differences in volumes calculated with the different DTMs was attained. These final result indicates the sensitivity of the volume obtained to the number of data points. As the number of data points increases the estimation error decreases, but at some point there is no significant decrease in the final volume with the collection of additional data.

Jan 1, 1995