Search Documents

By F Cappuccitti

A colourimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured. The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimisation of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimise the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.

Jan 1, 2005

By J J. Jiang, M Reimnitz

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is mining through a dense network of disused level workings and open stopes of greatly varying sizes. The condition of the stope crowns and remnants is often unknown, and ultimately these structures become a significant proportion of the production floor and pit walls. Significant seismic events and occasionally rock bursts often occur in the underground workings. Seismicity is becoming an issue to the viability of the KCGM Fimiston operations. KCGM needs to take a leading role in understanding mine-induced and regional seismicity. The seismic system trials were initiated in the Fimiston Open Pit in 1996 using the ISS system. The initial system included two triaxial geophone arrays and two triaxial accelerometer arrays installed into two boreholes. The main objectives of the trial were to investigate the suitability of the two types of sensors and the detectability of seismicity in the pit. The trial was regarded as a success and the system has been expanded and improved. The current system consists of 12 triaxial geophone and accelerometer arrays and nine uniaxial geophones. The 12 triaxial arrays are installed in nine boreholes drilled from the pit and the nine uniaxial geophones are installed from underground level workings about 660 m below the original surface elevation. The system is designed to provide seismicity coverage for the entire pit area that is about 2.7 kilometres long, 1.5 kilometres wide and about 300 metres deep. The accuracy of the source location has always been a challenge due to the existence of the dense concentration of stopes and lack of the sensors. It is uncommon to have direct ray path for the seismic waves to propagate to the sensors across the strike, hence sensors have been located along strike and under the old workings. This paper discusses some of the challenges associated with seismic monitoring near mine remnants and seismically active faults. The results of the seismic monitoring are presented, and contrasted to results of three dimensional boundary element numerical modelling. The impact of the seismicity upon pit slope stability is briefly discussed.

Jan 1, 2003

Chemicals derived from petroleum raw materials satisfy so much of our industrial needs today that it is good to pause and realise two things -ò the petroleum chemical industry is so new, and the use of chemicals is a very old one.Petroleum is such an'abundant and convenient source of raw material that in little more than 30 years it has become the major source of supplyfor chemical rdanuf ctiree This paperw~l'l 'disc'uss t1.e main 'r`easons' for this rapid development by considering the : sub jest -under tkzree headings ea. Source of Raw Materials.b. The Impact of Petroleum Chemicals on Plant Design and Processes. ce Scme of the Major Chemicals Used Today.

Jan 1, 1962

Thermal Processing of Petroleum Fly Ash for Vanadium Recovery

Sep 13, 2010

It is no longer satisfactory to assess the value of a coking coal on its intrinsic properties alone, its value depends upon its behaviour as a component in a blend. No single test can be used to make this assessment, it can only be made by carrying out a suite of tests. The quality parameters which are considered desirable, and which have widespread acceptance, have been discussed and their application to the blending of coals from New South Wales and New Zealand has been reported and discussed. Blending can be utilised to offset deficiencies, or capitalise on advantages, of the individual coals making up a blend. Coals can be blended, which alone are poorly coking, but which have compensating features. Blending also allows better exploitation of coking coal Reserves..

Jan 1, 1980

By F Sandrone, J-P Dudt, J Zhao, E Paltrinieri

Tunnel boring machines (TBMs) excavation is nowadays more and more considered a valuable alternative to conventional tunnelling. As a matter of fact, thanks to its advantages such as greater rate of advance and safer working conditions, the application of TBMs has increased significantly in recent years. Despite the possible excellent performance of TBMs in favourable ground conditions, the advance rates could be significantly slowed down or even obstructed in limiting geological situations. This obviously traduces in potentially longer tunnel construction times and higher costs and, therefore, in a preference for conventional method. One of the major geological hazards encountered during tunnel construction, is related to the presence of fault zones or heavily jointed and fractured rocks. The most common geotechnical problems resulting from tunnelling in these difficult conditions include the instability of the excavation face, instabilities of side-walls producing large overbreaks on the tunnel profile, excessive deformations in case of squeezing grounds, frequently changing stresses in terms of magnitude and direction, high water inflows, etc. The decisions aids for tunnelling (DAT) is a model and a computer code that can be used to evaluate the influence of the uncertainties related to both the geological/geotechnical conditions and the construction process on final tunnel construction time and costs. In this framework, the DAT is used for assessing the effects that challenging ground conditions may have on tunnelling operations in terms of costs and delays. This is done by simulating the tunnel construction considering several geological profiles. The aim of the study is comparing different excavation methods (ie drill and blast versus TBM) in changing ground conditions along the tunnel alignment ranging from good rock, to very poor and fractured formations. The results show the impact, in terms of changing construction time and cost, of the excavation method versus the ground conditions.CITATION:Paltrinieri, E, Dudt, J-P, Sandrone, F and Zhao, J, 2014. Comparison of excavation methods in different ground conditions with the decision aids for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 573–580 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The Olympic Dam copper/uranium deposit was discovered in 1975 and subsequently commenced production in 1988 at a rate of 1.5 Mtpa using the sublevel open stoping mining method. In the following five years the operation underwent two optimisation programs that have increased mine output to the current rate of 3.4 Mtpa of ore. The pre-expansion requirements were annual development of approximately 10 000 m and the placement of around 500 000 m 3 /yr of cemented backfill. Previous to 1995 all hoisting was carried out by the Whenan shaft. The Robinson shaft was commissioned during that year to hoist increasing development mullock tonnages and to allow for increased ore hoist via the Whenan system. In 1996 WMC committed to expanding the output of the operation from 85 000 tpa (1996/97 budget) copper metal to 200 000tpa. The corresponding increase in mine ore production requires expansion to a nominal rate of 9.0 Mtpa. To achieve these increased tonnages, major hardware installations will include sinking of a third shaft capable of hoisting in excess of 9.5 Mtpa, a rail haulage horizon utilising automatic trains, expansion of the existing backfill plant to a production capacity of over 1.8 million m 3 /yr, increasing long term development rates to 15 000 m/yr and increasing the production drilling and blasting rates in line with the higher stope production output. This paper provides detail into the intended hardware (shafts, equipment, etc) of the mining system, and outlines the intended long-term operation and management of the operation. Of particular note is the background requirement of ensuring existing production targets are met to provide critical cashflows into the project during the period of expansion.

Jan 1, 1998

By R J. Nicholson, J M. F Clout

As part of an overall strategy to make significant new technological advances for the sustainability of the mineral processing and related process industries CSIRO Minerals has developed a new dry separation device. It represents a technology breakthrough and has the potential to radically change the way in which dry particle size classification is achieved in the minerals industry. Conventional dry separation techniques have limited applications and often suffer from low productivity, high operating costs, low separation efficiency, the need for dust control and a lack of flexibility. In the absence of efficient dry techniques, wet processing is often used. The use of wet processing either requires the introduction of water into a separation process, which causes environmental concerns through the need for water supply and tailings dams or the use of æunfriendlyÆ chemicals for dense media separations that have considerable impact on handling and disposal. Wet processing also increases operating costs due to plant instability, materials handling, thickening, filtration and product drying. The new CSIRO technology exploits a combination of natural and applied forces to achieve specific particle motions that produce size separation. In doing so, many of the traditional shortcomings of dry separation have been overcome. The CSIRO Dry Particle Size Separator is ideally suited for dry size separation applications within the size range 1 mm to 30 ¦mfor moderate moisture levels (2 per cent), have low unit throughput, produce a fixed cut size and are therefore impractical where very high unit capacity and low operating costs are required. This paper presents a review of dry separation devices together with details of the new Dry Particle Size Separator and typical results for a number of materials, including iron ore and quarry dust.

Jan 1, 2002

Leichhardt Colliery is developed for underground mining of coal seams at depths exceeding 280 m. Investigations of the area were conducted in phases, each designed to delineate seam characteristics more accurately and to indicate with increasing precision the nature of local geological features and the ranges of those coal properties susceptible to variation. The investigational campaign is described phase by phase summarizing evaluation of the area at the conclusion of each phase. Predictions of geological conditions likely to influence engineering planning are contrasted with actual conditions observed during trial mining.

Jan 1, 1974

By B Hall

In feasibility studies the choice of optimum cut-off grade is typically based on an evaluation of tonnage grade curves and manual design of stopes at one or two cut-off grades. In the industry these stope designs are usually based on break-even cut-off grades, but there is little consensus on what cost and price assumptions ought to be included. A new tool for automated stope design has been developed that generates sets of stope shapes for a nominated range of cut-off grades, or depending on the nature of the mineralisation, cut-off values based on net smelter return calculations in the block model. The stope design procedure includes constraints in stope and pillar geometry for the selected mining method and can be used to evaluate sublevel interval and sensitivities to other design parameters in the specific geological and geotechnical environment. These ænested stopesÆ are analogous to ænested pitsÆ in open cut design, and can be used as a key input in the æhill of valueÆ methodology for the evaluation of the optimum cut-off grade in underground design. The results of many consulting studies indicate that a break-even cut-off grade will not be the optimum cut-off grade. A particular benefit of the new stope design tool is that the design rules used to establish stope shapes in the feasibility study can then be used in mine production, in an optimal and repeatable method. This methodology is being advanced in the AMIRA P884 PRIMO project, which is a new research collaboration coordinated by AMIRA International. The project has brought together active research groups in Australia and Canada, with the goal of developing a flexible framework and set of software tools for optimisation in underground mine design.

Jan 1, 2009

By Renwick MT

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in- situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

By E Villaescusa

This paper describes a methodology for the design of mine pillars at the McArthur River Mine. The pillar strength is calculated using a method that accounts for confinement, pillar geometry and intact rock properties. The average pillar stress was calculated using in situ measurements of vertical stresses at shallow depth and the tributary area method in conjunction with numerical modelling. Observations of pillar behaviour indicate that an existing pillar stability graph may be slightly conservative and further adjustments for the local rockmass conditions are needed. The results to-date indicate that all mine pillars are stable for a range of mining geometries at McArthur River Mine.

Jan 1, 1998

By Taylor R. K A, Berglin C. I K

The manganese ore deposits at Groote Eylandt are quite variable both in regard to grade and physical cond- ition. In order to treat a wider range of these ores and to increase production a new primary-crusher and' concentrator complex costing $8 million has been installed and commissioned to treat ore at the rate of 12,000 tonnes per day. The initial testwork carried out to determine the method of the ore treatment required, and on which the design of the concentrator was based, is detailed. The flowsheet and equipment used is discussed together with the operation of the plant. The production achieved and product qualities obtained are given.

Jan 1, 1973

By Swain H. D, Kay R. L

Assessment of mineral reserves in any ore- body hinges on both mineralisation characteris- tics and the economics of extraction. The mineral reserves statement depends on interpre- tation of diamond drill information by geolo- gists, determination of the production plan and operating costs by mining and metallurgical engineers and prediction of future income by economists. The techniques used to generate the mineral reserves statement for Bougainville Copper Limited in 1969 are described and the accuracy of predictions discussed. Preliminary results from a geostatistical reassessment are comp- ared with the ore zone model, blast hole data and concentrator reconciled production results.

Jan 1, 1979

The paper gives details of the reasons why attention was directed towards the modification of flotation cells. The cell volume and impeller speeds were reduced, and it is estimated that the power consumption for lead and zinc flotation will be reduced by about 2·8 kWh per ton of ore treated, and that substantial savings will be made in maintenance costs. The metallurgical efficien.cy of the operation has been maintained and attention is now being directed towards the improvement of grades of concentrates and recoveries of metals.INTRODUCTIONIt was on 1st August, 1934, that the first Denver No. 21 flotation cells were operated in the treatment plant of The Zinc Corporation Limited, in a pilot Nant which had been installed to determine the economics of all-flotation as against the then existing gravity and flotation practice.The ore being mined at that time came from the lead lode which consists of a granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, manganhedenbergite, garnet, fluorite, manganocalcite and apatite. The silver content of the ore occurs in three minerals-tetrahedrite, dyscrasite and pyrargyrite, the last two mentioned occurring in microscopic association only.A parallel lode, known as the zinc lode, was well developed at that time. The common lead lode gangue minerals-calcite, rhodonite, bustamite-were rare in the underground exposures of the zinc lode. No metallurgical work was done on this ore during the pilot plant operations although since then both lead and zinc lode ore have been treated.Early in 1936 plans were made for the complete re-organization of the mine operations, and in view of the metal-

Jan 1, 1956

By Cusack BL

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. This resulted in a deterioration in metallurgical performance with increased loss of lead and zinc to residues at each concentrator. Investigations to determine the cause of the problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical Deterioration.

Jan 1, 1970

This paper outlines the manner in which legislative control for tunnelling and allied operations has evolved, detailing Victorian experience. It examines the concept of mine managers as it relates to the industry and attemps to illustrate its benefits. The Victorian experience in relation to fatal and serious accidents is examined in detail, particularly in the allied art of trenching and examines the Krings system of trench lining support which is hoped will catalyse an increase of engineering expertise in this area. The paper concludes by demonstrating that safety awareness is not incompatible with production efficiency or economic viability.

Jan 1, 1981

By P Dean, M Elmouttie, Y Duan, X Luo

Slope instability is one of the major concerns in open pit mining operations. A significant collapse of the pit wall can result in injuries, damage to machinery and interruptions to production. A broadband microseismic monitoring technique has been developed for diagnosing the healthy condition of a target slope area. This technique has been successfully applied to an open pit mine in Chile. Our research has found that this microseismic monitoring technique can be used in open pits for tracking and locating a falling rock that is rolling on a slope, if a dedicated seismic sensor network has been established. In collaboration with other monitoring techniques (radar, laser scan, aerial photography), more accurate determination of rock rolling trajectories can be obtained. In this paper, an example of using the CSIRO microseismic monitoring technique at an open pit mine is presented. Results from an experiment where we used the microseismic technique for determination of the trajectory of a rockfalling on a slope are also presented.

Nov 8, 2021

By Smith M, Milton T, Pitt G

High levels of contamination (non magnetics) were present in the magnetite medium of the D.M. cyclone circuit. Attempts were made to minimise the amount of undersize (-lmm) material in the D.M. cyclone feed by improving initial desliming and examining those factors that contributed to any overall reduction in desliming efficiency. Circuit density control was improved and a system of continuous contamination monitoring implemented. A brief description is included of the major alterations to circuit control philosophy. The significant improvement in overall D.M. cyclone circuit performance is outlined.

Jan 1, 1987