Search Documents

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930

By M Bannear, J-F Wilhelmy, R Jones

Mineralogical study of the interactions between fluxes and iron-oxides helps to understand how magnetite oxidises to haematite during pellet firing. Samples of OneSteel magnetite pellets tested at COREM pilot plant were collected after three firing steps and were studied mineralogically. Preheated pellets revealed no particular microstructures related to the composition of fluxes but were more affected by their bed position. After kiln firing, the impacts of lime and magnesia became more apparent. Magnetite oxidation is complete in the cooling stage. The position and the microstructure of the residual magnetite can bring useful information that could æcompleteÆ the view of the firing cycle.

Jan 1, 2007

By Draper J. J, Jell J. S

The Burdekin Basin in the Townsville hinterland is an intracratonic extensional basin which contains up to 4500 m of marine and continental siliciclastics and carbonates. The basin sequence is recognised as having accumulated during five major episodes of deposition. Facies analyses of these show that each consists of one or more transgressive or regressive phases. Each episode led to the accumulation of thick sequences in several half-grabens in a transtensional back-arc setting. The depositional episodes can be recognised in comparable sequences in the Broken River Province to the west and Drummond Basin to the south.An Early Devonian episode resulted in the deposi-tion of dominantly marine facies, currently mapped as Fanning River Group, in the northern part of the Burdekin Basin. Two transgressive phases are recorded there, firstly in the Pragian, then later in the late Emsian to early Eifelian. A Middle Devonian episode is represented by dominantly marine facies of the Fanning River Group, representing the peak of a widespread late Eifelian to Givetian transgressive phase. A Late Devonian episode is characterised by continental facies of the Dotswood Group. Deposition occurred during a major regressive phase in response to regional uplift of surrounding areas, and the onset of acid-intermediate volcanism to the south. A Late Devonian to Early Carboniferous episode followed, which was a period of alternating marine transgressions and non-marine regressions that resulted in the deposition of the Keelbottom Group. A final Early Carboniferous episode, marked by the deposition of calc-alkaline volcanics and non-marine faciesòof the Glenrock Group, was a direct outcome of Early Carboniferous subduction further to the east. Compression of the basin followed in the Late Carboniferous, resulting in folding and reactivation of basement faults.

Jan 1, 1990

Mixers are commonly used for the transfer of oxygen in gas-liquid-solid reactions in minerals processing. The process rate is usually controlled by two steps: gas-liquid mass transfer and reaction kinetics. Some examples are described along with the factors used for analysis of the mass transfer design problem. Typical oxygen rates and appropriate types of aeration systems or mixers are reviewed. The commonly used Rushton turbine has limitations in a number of mineral processes. The development and characteristics of the LIGHTNIN A315 axial flow gas dispersion impeller are described. Some practical examples which highlight its advantages are briefly described.

Jan 1, 1992

By Flann R. C

A small modification to current industrial practice should lead to better nickel powders for use in alloying, electroplating, and powder metallurgy. Nickel powder compacts sold for alloying are not always suitable for electroplating applications, since some presently used commercial powders will expand on sintering. Further, such nickel powders are unsuitable for use in the production of powder metal parts, because of expansion during heating of the near-net-shape preforms. Research in these laboratories has enabled the elimination of expansion, and led to techniques for the production of compacts suitable, in particular, for commercial use in both alloying and electroplating. The techniques include: powder pretreatment, cold pressing and sintering, hot pressing, and hot pressing and sintering. In this way compacts are readily prepared with densities of at least 93 per cent of solid nickel, and these, when used as anodes in Watts general purpose and bright baths, give both cathode current and plating efficiencies of 90-98 per cent.

Jan 1, 1979

By M Kilburn, A Edenton, M Adam, A Dehghan-Manshadi, R Smyth, L Lu

The blast furnace is a counter current reactor. The counter current principle of the furnace makes it very efficient in transferring the heat and mass required to drive the reduction reactions inside the furnace. However, this does impose a stringent requirement on the permeability of burden material in the furnace. Lump ore is one of the key ferrous feeds used in the blast furnace ironmaking process, often accounting for ten to 20 per cent of the blast furnace ferrous burden. As the lump ore descends through the blast furnace, it is dried, heated and reduced by the ascending hot reducing gas. To ensure good furnace permeability, generation of fines from burden materials including lump ore due to mechanical, thermal and chemical processes needs to be minimised. Unlike sinter and pellets, lump ore is subject to thermal degradation. To assess this behaviour of lump, the ISO decrepitation test (ISO 8371, 2007) is often conducted, and the result is calculated as a decrepitation index (DI). However, the DI values obtained from the existing ISO decrepitation test vary considerably between test portions and between laboratories, which makes meaningful comparison very difficult. In order to identify the sources responsible for the unacceptable repeatability, the effect of various testing conditions, such as particle size, heating rate, sample preparation and loading method, on the mean DI value was studied. The mechanisms contributing to thermal degradation in the top of the blast furnace and during the standardised decrepitation test are also discussed.CITATION:Lu, L, Kilburn, M, Dehghan-Manshadi, A, Adam, M, Edenton, A and Smyth, R, 2013. Thermal degradation of lump ore in the top shaft of blast furnaces, in Proceedings Iron Ore 2013 , pp 421-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Unver B

Longwall advance mining is still the predaninant system of coal extraction in the U.K., contribiiting to sane 70 % of underground coal production. Gate roadways providing access to a longwall advancing coal face are maintained adjacent to a rib pillar under high strata abutment pressures and the caving rock mass. It is very difficult to realistically model such access roadways using mathematical or numerical techniques and hence, predict roadway closure. For the past 15 years, a research group in Nottingham University has been engaged in the study of longwall gate roadway stability using observation methods. Gate roadway deformations have been measured in 224 gate roadways and a comprehensive data base has been established. The paper describes the statistical analysis of this database and presents sane. predictive equations which will enable a forecast of the gate roadway closure to he made. Further field work to validate these equations. is described together with an error analysis. The results are very promising and indicate that it is possible to predict gate roadway closure in the U.K. within practical limits of Accuracy.

Jan 1, 1986

By Jancar T, de Guzman M M, Matthews B, Tu J. Y

The use of computational simulation to predict the performance of existing equipment or for the design of improved mineral processing equipment will be referred to as Computational Mineral Processing (CMP) in this paper. The emphasis will be on solving the governing equations for liquid solid flows in complex geometric domains to obtain, typically, the three-dimensional distributions of velocity and pressure for the liquid phase and the velocity and concentration for the solid phase. The underlying technology, computational fluid dynamics (CFD), is very well-developed in other industries (aircraft, car and chemical) and forms a vital part of product design and analysis. The subsequent design of improved mineral processing equipment may also involve finite element structural analysis (FESA). Computational fluid dynamics (CFD) and finite element structural analysis (FESA) are part of the generic discipline of Computational Engineering and Science (CES). Ciment and Scherlis (1993) define CES as `The systematic application of computing systems and computational solution techniques to mathematical models formulated to describe and simulate phenomena of scientific and engineering interest'. Increasing computer power (Kaufmann and Smarr, 1993), is a dominant factor determining the rapid growth of industrial utilisation of CES. This increase is happening at both the supercomputer and the workstation level. Indeed, today's typical workstation, a Hewlett-Packard 735, is as powerful as a CDC 7600, the leading supercomputer in 1970. Future computer architectures are expected to become increasingly parallel (Gartner Group, 1990) allowing a sustained performance of a teraflop (a million megaflops) to be achieved well before the Sydney Olympics in the year 2000. It is recognised that the modem development of most disciplines in the physical sciences rests on the three complementary strategies of experimentation, analysis and computational simulation. As the 21st century is approached the volume of computational simulation, both fundamental and applied, is growing dramatically and the role of experimentation is diminishing. In the area of equipment design, CES provides the following advantages over experimental testing and measurement: 1. lead time in design and development is significantly reduced; 2. CES can simulate conditions not reproducible in experimental tests; 3. CES provides detailed and comprehensive information; and 4. CES is more cost-effective and time-efficient. The ultimate benefit for industry is greater productivity and hence greater profitability. The broader issues in relation to CFD are discussed by Fletcher (1993b). In the five- to ten-year time frame, growth in computer power will make it practical to combine CFD and FESA with optimisation procedures to produce a design process that is almost fully computerised. It is expected that fully automatic

Jan 1, 1995

Grade control aims to deliver quality tonnes to the mill via accurate definition of ore and waste. It comprises data collection and interpretation; local reserve estimation; supervision of development and mining; and stockpile management. The foundation of all grade control programs should be that of high quality sampling supported by geology. The requirement for quality grade control samples has long been recognised, where they should be representative, unbiased, safe and operationally timely. Underground sampling methods include chip and channel samples; grab samples; and drill-based samples. To achieve quality samples, collection techniques employed should minimise delimitation, extraction and preparation errors. Grade control staff should be well-trained and motivated, and mining staff should understand the need for grade control. This paper reviews grade control sampling methods and presents recommendations for best practice and minimisation of sampling errors.

Mar 1, 2010

FOR some time it has been recognised by the Metallurgical Staff that the presence of pyrite in the ore was adversely affecting the grades of the flotation concentrates.Following experimental work, it was decided to change over from the acid circuit in the mill to an alkaline circuit. The following description sets out the procedure adopted, -and the results obtained when such change-over was made.The Zinc Corporation ore consists mainly of galena, marmatite, calcite, and quartz, with smaller quantities of pyrite, fluorspar, and rhodonite.A clean specimen of marmatite picked from the ore assayed 53.4% zinc, and 10% iron, with no lead or insoluble. However, as zinc concentrates have been, at times, produced in the plant assaying over 53% zinc, and with only 8.7% iron, apparently the picked specimen of marmatite did not represent an average composition.The average would probltbly be between 8 and 9% of iron, and from 53.5 to 54.5% of zinc. It is obvious, therefore, that from this ore it is not possible to produce zinc concentrate of a higher grade than this average figure.In the Colorado School of Mines Quarterly for April, 1928, Vol. 23, No. 2, on page 47, we find the following statement:As the zinc in the ore exists as marmatite, which contains approximately 54.5% zinc and 10% iron, 49% zinc in the concentrate may be considered high.This statement refers to the ore treated in the Sullivan concentrator, owned by the Consolidated Mining and Smelting Company of Canada Limited.

Jan 1, 1930

On the 18th November, 19'58, the first coal was delivered to the Morwell Power Station from the adjacent Open Cut using conveyors for the transport of the coal from the working face to the boiler bunkers. As the cut develops the coal seam will be worked for its full depth of about 360 feet from four benches, each feeding a conveyor line along th.e face and up out of the cut to the power station and briquette factory. By 1970 the estimated maximum daily demand reaches 60,000 tons and the total annual output 18 million tons. The complete conveyor installation will then total some 9 miles with a capital cost of over £3~ million.The choice of conveyors in place of the more usual rail system was made possible by the development of movable belt conveyors which use mechanical conveyor shifting, high belt speeds and flexible high strength belts and the paper deals with these and some other aspects of the scheme.INTRODUCTIONThe development of brown coal deposits is usually based on open cut workings equipped with a few large dredgers giving an almost continuous output of coal or overburden which has to be hauled a comparatively short distance. These are ideal conditions for conveyor operation, and it is surprising that, until recently, rail transport has been used almost exclusively in brown coal open cuts. In some cases inclined conveyors have been introduced to take the coal from the coal levels up out of the cut to bunkers at groundlevel, but trains have been left to operate between the ditch bunker feeding the conveyor system and the dredger.

Jan 1, 1960

By Quinlan M. J, Ratcliffe J. S

Chemical kinetics is a dependent process which usually correlates the rate at which a reaction proceeds with the mechanism descriptive of the manner by which reactive particles interact. Given the latter, the object gen- erally is to find the reaction rate dependency in terms of an intensive property of the system - number of reactive particles present, and of the energetics of the system - usually temperature. Chemical kinetics depend on a dem- onstration that reaction considerations alone control the phenomenological process under study. For these rea- sons, chemical kinetics are usually involved in homogeneous gaseous systems. Even in liquid homogeneous sys- tems earliness or lateness of reactant mixing rather than chemical kinetics may be controlling. Considerations of transport phenomena are involved in heterogeneous systems and often control the observable rate:an additional problem in such systems is to apportion the rate due to mass transfer - usually a linear process - and that due to reaction which may be linear or non-linear. Experimentally, conditions are often chosen so that only one consideration controls but this becomes more difficult where solid phases are involved. Kinetic modelling involves considerations of chemical kinetics, transport phenomena, and factors attributable to the physical environment in which the process takes place. The latter two considerations may be quite different as between experiment and plant. The kinetic model may be a mathematical representation of a conceptual mech- anistic model of the reaction. Alternatively, it may be an empirical relationship resulting from, for example, some curve fitting procedure applied to experimental data. The latter approach may be necessary where the system is particularly complicated.

Jan 1, 1975

By J R. Manuel, M J. Peterson

Selected drill core samples from a Ferrobamba-limestone-hosted, magnetite-haematite skarn deposit, located in the Apurimac department of the Andahuaylas-Yauri skarn/porphyry belt of south-eastern Peru, were mineralogically and texturally characterised to gain a preliminary indication of the deposit's potential as an iron ore resource. Optical microscopy, X-ray diffraction (XRD) and scanning electron microscopy/electron probe microanalysis (SEM/EPMA) techniques were utilised to determine the characteristics of magnetite, haematite and/or goethite dominated ore types, including variations in the relative proportions and textural relationships of the ore and gangue minerals. The deportment of elements deleterious to processing performance (eg copper, sulfur and potassium) was determined and the beneficiation potential of the samples was briefly assessed. In drill core sections, the ores are grey to reddish in colour, massive and 'metallic' to dark brown and earthy in character, moderately hard and porous (macro and microporous), with variable gangue infill. Ores often appear weathered, typified by ochreous goethite staining and common minor goethite (except in dense core fragments), occasionally exhibiting a more friable texture with coarse magnetite/martite grains. Silicates and lesser carbonate gangue are visible as blue-green to beige to white scaly and/or shaly surface coatings, and finely particulate infill, often goethite stained. Sulfide-rich ore types also occur in part of the deposit, but are restricted to specific drill holes. Magnetite grain size is relatively coarse, compared with magnetite from typical banded iron formations, whereas discrete silicate gangue is mainly bladed/fibrous and/or layered and micaceous in form. XRD analysis indicates the presence of vermiculite, serpentine, stilpnomelane, chlorite, actinolite and clays. There is a spectrum of ore types representing the gradation from 'fresh' (magnetite-dominated) to oxidised and weathered (martite/goethite-dominated). Martite-dominated samples are generally higher in grade, due to leaching and removal of silicate gangue, resulting in higher macroporosity. Where gangue has been leached out, partial replacement by vitreous goethite and/or hydrohaematite is typical, often preserving the fibrous/layered characteristics of the original silicates.

Jan 1, 2009

Upper Cretaceous and Eocene coal measures of the Ohai Coalfield are stratigraphically complex, and coal seam geometry and quality are influenced by washouts and partings resulting from accumulation in a fluvially active environment. Mining efficiency is influenced by these seam discontinuities, which are difficult to predict in the absence of refined paleoenvironmental models of peat accumulation. Petrographic variations between the Upper Cretaceous and Eocene coals indicate differences in the environments of peat accumulation. Seams in the Upper Cretaceous Morley Coal Measures accumulated autochthonously (in situ) in predominantly forest swamps with a high water table. These swamps were occasionally subject to brief floods. No significant changes in swamp vegetation, as indicated by petrography, have been detected between seams. In contrast, the greater content of mineral matter and maceral detritus within the Eocene Beaumont Coal Measure seams indicates hypautochthonous (locally transported) peat accumulation under more frequently flooded conditions. A precursor forest-moor is again indicated but the greater resin content of these coals compared with the Upper Cretaceous examples may suggest a greater contribution from conifers. Integration of coal petrography with investigation of other seam characteristics and coal measure sedimentology is expected to result in a detailed understanding of original depositional controls on peat accumulation. Paleoenvironmental models derived in this way should facilitate prediction of seam geometry, roof and floor conditions, and variations in coal quality, with obvious benefits to exploration and mine development.

Jan 1, 1983

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

In Mount Isa voltage and frequency fluctuations caused. by haulage shaft operation gave considerable difficulties with the initial application of Atomic Absorption Spectro-photometry.The methods used to stabilise the various units ' have been described.- Some other difficulties and the means used to eliminate or reduce them together with a-modified burner design are also discussed.

Jan 1, 1963

This paper outlines some of the recent developments in Spiral Concentrator design, with particular reference to the range of Reichert spirals supplied by Mineral Deposits Limited, typical applications, and test or operating data, are also provided for the different series of spirals now available.

Jan 1, 1978

By Nguyen G. H, Graham J

A laboratory-scale fluidised-bed roaster has been used to examine the effect of temperature and duration of roast on the morphology of the calcine produced from a pyritic gold-bearing concentrate. Two mechanisms of oxidation, which depend on the roasting temperature, have been identified. For samples roasted below 550°C, direct oxidation of the sulphide occurred to form hematite with a porous fine-grained concentrically-layered texture. The surface area of the calcine increased with an increase in roasting temperature in the range 400 to 500°C. For samples roasted above 550°C, the first reaction was the evolution of sulphur vapour to produce pyrrhotite, which underwent increasing grain growth as the roasting temperature was increased. This had the effect of decreasing the surface area of the calcine. The pyrrhotite was subsequently oxidised to produce hematite.Leaching studies using cyanide solution indicated that gold extraction around 95 per cent was achieved at temperatures of 500°C and above, with optimum extraction, taking into account rate and cyanide consumption in the range 550 - 700°C. Hence recovery did not decrease with decrease in surface area of the calcine. Observed gold in leached calcines was mainly enclosed in thin oxide walls of the hematite, with minor quantities enclosed in quartz and silicate minerals.

Jan 1, 1995

This paper presents the findings from an experimental study of the effects of shock and gas penetration breakage mechanisms in rick blasting. A blasthole liner method, which realistically seperated these two basic sources of energy in blasting, was developed and utilized. The use of four different explosives with contrasting detonation behaviour produced a wide variation in the nature of explosive energy transfer to the rock. Through extensive field experiments it was found that, relative to low VOD dynamite, the high VOD emulsion imparted greater shock to the rock and therefore produced finer fragmentation and greater back damage. The comparatively lower heave energy of the emulsion caused less immediate blast results were obtained with watergel and ANFO explosives, which have detonation behaviour and energy partitioning charecteristics lying between emulsions and dynamite.

Jan 1, 1990

By Chapman G. J

Mining operations require detailed and precise methods and procedures for the optimum selection of ore from waste. A fundamental procedure applied to achieve this selection is accurate sampling. The key parameter to accurate sampling is an understanding of the degree of heterogeneity of the key element contained within a sampling mass. This paper will describe the methods applied for the calculation of the fundamental sampling error and the techniques used to achieve a representative sample in the Fimiston Open Pit, Kalgoorlie.The utilisation of Pierre Gy's sampling theory has optimised the blast hole sample quality and quantity for submission to the assay laboratory. This has resulted in reduced cost and optimised assay reliability in statistical terms. Similarly the analysis of exploration drill holes for resource definition has optimised drilling procedures in terms of the drilling method, sample length and sample quantity.

Jan 1, 1993