Search Documents

By M Schmid

German hard coal mining operations have decreased for more than 40 years. Current political decisions are leading to a discontinuation of subsidised black coal mining by the year 2018. This decision will, however, be reviewed once again in the year 2012. The enormous increases in productivity, which were achieved in previous years, have so far not led to an achievement of market requirements. Coal mining at depth of more than 1200 m in multiple seam environments is not yet competitive in global comparison. In 2008 the 24 faces left in eight mines produced about 20 million tonnes of usable steam coal. Management and the workforce will be reduced in parallel; from today until 2012 by more than half. The average age of personnel is increasing dramatically and nearly no new personnel are recruited. With this background in mind, increasing continuously coal mining productivity becomes more and more difficult. Above all, this goal was reached by mechanisation, then by increasing the mining machine power and then by enhanced machine control systems. The first attempts to automatically operate full face equipment from above ground were in the early 1980s. After successful automation of the face equipment, the emphasis is now on mine logistics. Autonomous monorail transport was introduced and tested in 2007. Since the development rate of machine improvements has its limits, the focus is on the full interaction of the total production system. Here information technology (IT) becomes important; the driver for more productivity. Actual developments aim for the complete and general homogeneous IT infrastructure both above ground as well as underground. The explosive environment needs high level investments in safe technology, eg access points for WLAN and fibre optics for underground use (ATEX certification). New technology availability also drives the enhancements of management and process control systems. Innovations in the mining industry often comprise technology advances through the adoption of well-known technologies. With virtual reality (VR) teaching and training systems advanced computational instruments, both in software and hardware development, were applied in the German coal mining industry for ten years. Widening lists of applications as well as the encouraging achievements show the economical benefits of investing in virtual reality technology both for teaching and training and for knowledge management. The paper discusses the actual technical achievements as well as in IT infrastructure utilisation and also in employment of virtual reality based systems. Special focus and deeper insight will be given to the fibre optics and WLAN hardware integration as well as software developments. The pocket personal computer (PC) is used to enhance underground material transport and data acquisition. The knowledge-based maintenance system (KBMS) integrates real-time virtual reality knowledge elements, such as repair process descriptions. It gives access to expert documentation by intelligent search algorithms and 3D representations of major mining machinery.

Jan 1, 2008

BECAUSE of the attention given in recent years to the flotation process, there is an extensive range of equipment available to any staff detailed for: the design of a flotation mill. This statement applies not only to the flotation machines, but also to equipment for crushing and grinding, elevating the pulp, dehydrating of concentrates, and the methods of driving the various equipment.Distributed through the Proceedings and Transactions of various metallurgical societies and journals there are many excellent descriptions of flotation mills, their equipment and performance.Whilst these articles describe-in many cases in detail-the equipment in the mills to which they refer, the reasons which govern the choice of each particular equipment are not usually given.

Jan 1, 1929

BHP-Utah Coal Limited operates 33 draglines of varying sizes in the Bowen Basin of Central Queensland. The group's operations with draglines commenced in 1963 with the establishment of opencut operations at the then TPM Moura Mine and continued through expansion of that mine, the commissioning of the Utah Development Company Blackwater Mine in 1968, and the subsequent establishment of six (6) other large opencut mines, all in the general area over the next fourteen years. These operations generally commenced with boxcuts on the sub-crop at depths of 15 to 25 metres. Over the years, depths have increased so that average depths now are in the 45 to 50m range. It was soon realised that dragline operations would have to be supplemented with additional stripping equipment. In 1981, a symposium "45m and Beyond" was held in Rockhampton to assess the problems associated with such "deep" stripping. Subsequently, dragline operations have continued and although addi- tional stripping capacity has been added, in many instances, draglines have been used and are being used to dig depths greater than 45m, some- times as much as 65 to 70m.

Jan 1, 1989

Attention is drawn to the largest eruptions with dense rock equivalent (D.R.E.) volumes approx-imating 50 km3. These have been strongly clustered during the last 40 000 years, with 11 recognised in the period 35 000 to 22 000 years ago, and 10 in about the last 9000 years, but none in the period 22 000 to 9000 years ago. With the latest such eruption, at Tambora, only 175 years ago, it is likely that we remain in a period of increased activity. During the last 100 000 years, roughly the period during which modern Homo sapiens has existed as a species, there has only been one eruption an order of magnitude larger (>_ 500 km3 D.R.E.). This took place at Lake Toba, Sumatra, about 75 000 years ago, and is estimated to have deposited ash to a thickness of a centimetre or so in parts of Ethiopia, Somaliland, Saudi Arabia and Iran, and to a thickness of a few millimetres in the eastern Mediterranean. The average interval between global eruptions of this magnitude is probably about 40 000 to 50 000 years. Insufficient work on the Quaternary history of volcanoes has been carried out to suggest where the next such eruption might occur. At Yellowstone, which has been well studied, the average interval between very large explosive eruptions is about 700 000 ¦ 120 000 years.As a prerequisite for magnitude-frequency analysis of eruptions, and hazard and risk impact assessments, it is important to classify past eruptions in a consistent manner. In an attempt to find a universally applicable method to estimate order of magnitude D.R.E. volumes from the distribution of airfall tephra, an empirical correction has been derived for the elongation of tephra dispersal fans due to wind. Dispersion distances for various thicknesses of tephra, recalculated for windless conditions, have been obtained from a study of about 40 tephra isopach maps for which D.R.E. volumes have been calculated, and a range of distances derived, equivalent to D.R.E. volumes from 106 m3

Jan 1, 1990

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By Roe P, Lowell A

This paper outlines software development and design work carried out by Mincom Pty Ltd in collaboration with Capricorn Coal Management (CAPCOAL) for computer based design of rehabilitated strip mine landforms at German Creek Mine. Current developments and future application areas for this software are also discussed in relation to other mines in Central Queensland. The development program was initiated in response to statutory requirements placed on mining companies in 1990 to produce a five year Plan of Operations which was to include a contour plan of the final rehabilitated mine landform at the end of the five year planning period. This plan was to be submitted to the Department of Resource Industries (DRI) by 1 December 1990. Due to the limited time given to prepare the plan, a work program was formulated in collaboration with Mincom Pty Ltd to develop suitable software to carry out the design work and provide the required plans and quantities. The software had to include computer based methods to allow design of the proposed landform in line with the rehabilitation strategy adopted by CAPCOAL at the time.

Jan 1, 1991

The main features and recent developments in the processes of benefication and extractive treatments of tin ores are reviewed. The need for development of processes to recover fine tin, tin from low-grade complex ores and from hard rock resources is indicated. The progress in understanding of slag-metal interactions and developments of fuming processes on industrial scale is delineated. the processes and prospects of hydrometallurgical and chlorination methods are briefly indicated.

Jan 1, 1992

Commencing early in 1975, Saraji Mine in Central Queensland will product 3.56 million tonnes in the first year and then 4.57 million tonnes annually for the Japanese and European markets. The coal will be mined from a series of pits separated by corridors which will be mined at a later date. Through the corridors flow regional drainage structures and power lines. Relatively easy areas will be mined initially to assist the cash flow and to minimise start-up difficulties. For ease of scheduling it is desirable that pit lengths exceed 3 000m but this will not always be possible. Ramps were designed using 1 200m spacing and 5 per cent gradient as optimum but modified to suit specific conditions. One ramp will be in the end of each pit nearest the ROM hopper and stripping will commence from this end. The advantages so gained are shorter haul distances, immediate access to the coal after stripping and simplification of the excavation of the first ramp. Haul road location was defined by the minimum present value of construction plus operating costs. Road design utilised airfield construction charts because wheel loads were outside the range of available road design manuals. Low load resistance characteristics of

Jan 1, 1974

The, Ore-bodies.-The ore-bodies of the North mine, North Broken Hill Ltd.; consist of two lenses, connected by a narrow neck of mineralized country. They pitch at an angle of 40° in an easterly direction and dip north at 60° to the horizontal. The southern ore-body, on a horizontal plane, has a total maximum length of 800 feet and in one place attains a width of 230 feet, whilst the northern orebody has a maximum'length of 600 feet and a maximum width of 80 feet.

Jan 1, 1940

By Greenhalgh L. P H

The opportunities offered by an increasingly volatile world invite the international consultant or engineering services contractor to broaden attitudes, diversify interests, expand capabilities, retain and develop specialist skills and base judgements upon sound principles and solid experience. The wide-ranging scope of this review reflects such a change but the topics of discussion are not intended to be exhaustive or to detract from many other current developments.The subject of environmental protection, effluent control and pollution prevention is a primary consideration in the application of many mineral processing technologies but is not covered here. There is an array of developments relating to noxious gas emissions and toxic wastes and the paramount importance of this matter justifies comprehensive conferences dedicated solely to the application of suitable measures. This review concentrates therefore on the main stream processing techniques for the primary recovery of values.

Jan 1, 1993

By Lovitt M

Ora Banda Gold Mine is located in the Eastern Goldfields of Western Australia. Mining is carried out underground by sublevel open sloping resulting in large open stopes. A Mass Blast of approximately 250 000 tonnes was carried out in July 1994 to recover a rib pillar between two stopes, and the crown pillar between the underground mine and the abandoned open pit above. Strategic development within 50 m of the blast consisted of two ventilation shafts and the main decline. This development required careful design and prediction of the blast results. This paper describes the design of the blast, the prediction of the likely effects, the measures taken to reduce the risk to important development, and the results of the blast.

Jan 1, 1995

BHP is the world's largest copper concentrate producer with production from mines at Escondida (Chile), Ok Tedi (Papua New Guinea), and Island Copper (Canada). The entire concentrate production is further processed into refined copper by third-party smelters around the world. In anticipation of an expansion in the global copper concentrate production capacity and a corresponding increase in treatment and refining charges by copper smelters, BHP has continuously evaluated various opportunities for downstream copper processing. An expansion in the Escondida mine production, combined with BHP's interest in processing some of its concentrate production on-shore in Chile, ultimately resulted in the development of the Escondida Leach Process. This process was specifically developed for higher grade concentrates, such as from Escondida. An ammoniacal lixiviant and air are used under ambient conditions to leach less than one-half of the contained copper values. After solid-liquid separation, the solution is subjected to solvent extraction regenerating the ammoniacal lixiviant and the copper loaded organic phase is stripped in spent electrolyte returned from the electrowinning plant where ultra-high quality SX-EW copper is produced. The solid leach residue can, if required, be upgraded by flotation to produce a high-grade copper concentrate with improved fuel values and a pyrite tail for disposal. After an 18-month bench and pilot plant scale program and an engineering feasibility study, Minera Escondida Limitada decided to build an 80 000 tonnes of copper per year facility near Antofagasta, Chile. The installed investment cost amounted to around $160 million. The plant went into commercial production in November 1994 and better than 99.9995 per cent Cu cathodes were produced right from the start. BHP believes that the process and the commercial plant are an excellent example of a novel approach advancing the science of copper metallurgy in harmony with present demands for environmentally sound processes and high quality products.

Jan 1, 1995

By Nye P. B, Fisher N. H

At the second Empire Mining and Metallurgical Congress held in 1927, the Empire Council of Mining and Metallurgical Institutions was formed and it was proposed that the Council take steps to prepare a "Review of the Mineral Resources and Industries of the Empire." At the third congress in 1930, it was resolved that the proposal to institute the review should be submitted to the Imperial Conference held in 1930. This was done, and the Minerals Committee, of the Imperial Economic Committee compiled, an interimreport which was based on statistics of imports and exports, and did not consider resources and consumption.In 1942 the Institution of Mining and Metallurgy, London, wrote to the Empire Council and stated that it was desirable that the Council should be in a position to take part in decisions affecting the future of the mining and metallurgical industries. The Council communicated with the constituent Institutions regarding the nominations of two members then in England. Subsequently the Mining, Geological and Metallurgical ,Institute of India prepared a review of the mineral resources and industries of India and their post-war development, and the Empire Council forwarded a copy to the Australasian Institute of Mining and Metallurgy and asked if that Institute would submit a review on simjIar lines for Australia. The Australasian Institute arranged that the Australian review should be prepared by...

Jan 1, 1946

Proceeding from statistical data on the development of waste volume, an endeavour was made to characterise waste materials with regard to the applicability of treatments based on mineral processing. Many types of waste are characterised by a high heterogeneity. The separation processes used for processing raw minerals can also be used for separation of various waste mixtures. For some waste mixtures, differences in properties can be utilised for separation which are mostly less distinctive for raw minerals. State-of-the-art technology is illustrated with selected Examples.

Jan 1, 1993

By Aspinall T. O, Loch R. J, Bell L. C

Design of reshaped spoil surfaces is an important pan of rehabilitation of spoil piles resulting from open-cut coal mining. To achieve the optimum design, it is necessary to make accurate predictions of soil losses from spoil piles. Predictions can be based on data gathered using laboratory and field rainfall simulators and field plots. These data are used to derive input parameters for erosion prediction models. Model input parameters include rainfall erosivity, spoil erodibility, sediment size distribution, runoff, soil loss and peak runoff rate. Model outputs can be used in design and include predicted sediment size distribution and predicted soil loss.The traditional method of gathering input data is monitoring field plots. This method is very expensive, must be done on a long-term basis and is affected by irregular rainfall. Long-term field plots are necessary to obtain data that can be applied to empirical prediction models such as the Universal Soil Loss Equation (USLE).

Jan 1, 1992

By M-E Boucher

While the haematite concentrates produced in Eastern Canada and the magnetite concentrates that Australia will soon be producing are different feed materials, the pellets they produce have similar physical and metallurgical properties. This paper will examine the similarities and differences in the evolution of pellet microstructure for pellets produced from magnetite and haematite. The molten slag phase generated at high temperatures has a lower melting point when in contact with magnetite compared with haematite due to the higher divalent iron content. The presence of some slag is beneficial for bonding but too much can inhibit oxidation of magnetite, although slag generation at lower temperatures reduces energy usage. In pellets produced from haematite, magnetite is generated artificially from the combustion of the carbon particles added to the pellet feed as a source of energy. Maintaining the optimum production level and mineralogy of such æsecondaryÆ magnetite, allowing for its subsequent reoxidation, is important for the quality of haematite pellets. In both magnetite and haematite pellets, balancing the slag formation and oxidation (re-oxidation for haematite pellets) of the magnetite (secondary magnetite for haematite pellets) is necessary.

Jan 1, 2007

By J F. C L Costa, J C. Koppe

The goal of this study is to characterise co-processed clinkers by identifying the most common minor elements, their distribution in the clinkers and possible effects on the mineralogical properties of the same. The results show the presence of an elevated content of transition metals, especially manganese concentrated in the matrix (up to three per cent) of the clinkers. Anomalous concentrations of arsenic have also been detected, especially at silicate crystal edges. The results indicate that the tracer elements can perfectly be associated to the mineralogical characteristics of the clinkers.

Jan 1, 2008

Low-grade, porphyry copper type mineralization at the Moonmera prospect is related to the intrusion of a granodiorite porphyry mass into the Upper Permian "Gracemere granodiorite". Significant copper mineraliza- tion appears to be associated with the alteration assemblage quartz-sericite- kaolinite. The ore shell is surrounded by a zone where montmorillonite and kaolinite are in greater abundance and this assemblage is over- lapped, mainly at depth, by potassium feldspar alteration. Secondary biotite is abundant throughout the mineralized zone. Preliminary sulphur isotope results on the sulphide mineralization are compatible with a magmatic origin for the sulphur.

Jan 1, 1974

Rifting and transfer faulting in the Late Cretaceous to Early Tertiary resulted in the formation of the Bundaberg Trough and Wallaville Basin and deflected the margin of the Maryborough Basin southwestward between the Kolan and Burnett Rivers. During the Cainozoic, three periods of volcanic activity occurred in the Bundaberg-Gin Gin area. The oldest of these periods, Paleocene to Early Eocene, resulted in the outpouring of tholeiitic lavas. During the Late Miocene to Pliocene, undersaturated alkali basalts generated at depths of from ca. 35 to 55 km were emplaced. These lavas were followed in the Pleistocene by the alkaline Hummock and Berrembea Basalts. The loci of eruption of all of these lavas were controlled by the intersection of the transfer fault system and pre-existing north to northwesterly trending faults in the Bundaberg-Gin Gin area.

Jan 1, 1990

By Sorentino C

Mineral valuation may appear to be a special field of financial valuation when in fact it is a subset of general investment decision theory. The only significant difference in mineral valuation is that in the case of valuing an on-going mineral asset, ie a mine, often there is no initial capital outlay involved. One is required to determine what the mineral asset as it stands is worth. But this is the same problem as determining the maximum one could pay today and not incur a loss over the life of the asset. In other words one needs to determine the Net Present Value (NPV) of the asset. The two most widely used discounted cash flow methods, NPV and Internal Rate of Return (IRR) came of age with the rapid adoption of the personal computer and spreadsheet programs. The two methods are directly related as the IRR is a special case of NPV. NPV measures the absolute increase in real wealth that can be expected from a certain investment, which makes it particularly suitable for mineral asset valuation, but ignores the efficiency of the investment. In contrast, IRR gives the expected efficiency of the investment but ignores the increase in wealth aspect. IRR has two serious theoretical weaknesses; multiple IRR's and a very rigid assumption about the rate of return of reinvested proceeds, plus if no initial equity expenditure is involved there is no IRR. The choice of the ""hurdle"" rate can also be a problem and in certain circumstances one can obtain different rankings of mutually exclusive projects using IRR and NPV. Although NPV and IRR supposedly measure financial risk, in fact they only address a very narrow area of risk, namely the time value of money given the real discount rate. They side step the issue of what the real discount rate should be and varying degrees of risk. The classical way to establish the real discount rate is to use the weighted average cost of capital.

Jan 1, 1994