Search Documents

Broken Hill South Limited's discovery of phosphate deposits in the northwest of Queensland in 1966 prompted intensive exploration which has proved phosphate rock in excess of 2,000 million tons at ten separate deposits.Systematic exploration for phosphate in Australia was initiated by the company in 1964. Early in 1966, an investigation of oil wells in the Georgina Basin in the Northern Territory and Queensland revealed widespread anomalous phosphate in early Middle Cambrian Beetle Creek Formation and Thorntonia Limestone. Phosphorites recognized in oil wells in the southeastern part of the Basin, Queensland, led to the discovery of the Duchess deposits. Exploration of the Beetle Creek Formation since 1966 has disclosed nine other sizeable deposits north of Duchess around the eastern margin of the Basin. The Lady Annie and the adjoining Lady Jane deposits, by reason of their location, 160 miles south of the Gulf of Carpentaria, are expected to be the first to be brought into production.Beneficiation testing and engineering investigations commenced in 1967. Transport between the deposits and various port sites in the Gulf of Carpentaria has been extensively studied and a slurry pipeline as a means of transport to a deep water island port, is now being investigated.

Jan 1, 1971

By Readett D. J

Soluble salts can be removed from Bowmans lignite by water and acid leaching. The success of the removal of water soluble or acid exchangeable impurities is directly associated with the efficiency of dewatering these slurries. The filtration characteristics of a slurry at its natural pH (4.0) were poor, with a filter cake moisture of 65%. Acid treatment of the slurry at pH2 caused the filter cake moisture content to drop to 61 %. Various oils, oily surfactants and a flocculant were tested to determine the conditions for minimum filter cake moisture. A series of pilot scale filtration tests were conducted on flocculant dosed slurries with and without washing on a horizontal test unit. Moisture contents of 54% were obtained in laboratory testing using high additions of oily surfactant. For the pilot scale test work, moisture levels close to 60% were obtained with low flocculant additions, similar to results obtained in laboratory studies. Removal of soluble salts could be correlated directly to the final moisture content of the filter cake. This process of leaching followed by filtration resulted in the removal of approximately 75% (more than 80% with washing on the cloth) of the sodium chloride originally present in the lignite.

Jan 1, 1989

The appearance of the Cornish miner in South Australia was, in the simplest terms, the result of resource development economics. In Cornwall in the middle of the 19th century tin and copper mining was declining, while in the new colony of South Australia copper mining was booming. Experienced hard rock miners in Cornwall there- fore escaped unemployment at home by accepting an assisted passage to South Australia. There, in a colony where they were needed, they made their skills available and received good wages. There are many testimonies which support this simple thesis. Take for example the following extracts from contemporary newspapers in Corn- wall: Persons of small capital will find this an excellent opportunity for emigrating to the young and thriving colony ... The miner will find a rich and unbroken field for his operations. The Colony abounds with minerals... (West Briton, 19 July 1844) Miners make a great deal of money here (South Australia). All of them earn ú2 to ú3 per week and in many cases when they have a portion of the mine on tribute one person has cleared ú100 in a couple of months or so. (Cornwall Royal Gazette, 21 July 1848)

Jan 1, 1987

By Khosrowshahi S

The objectives of grade control remain unchanged but new methods are being developed to attain them. Since the early-1990s, an improvement in the power of mine site computers has made the geostatistical tools of conditional simulation more accessible. Optimisation of the grade control process on mine sites now involves two stages: optimisation of the sampling regime and optimisation of the interpretation of ore and waste boundaries. Optimisation of the sampling regime first requires an understanding of the nature of the mineralisation and in particular the impact of particle size on the sampling precision. This relationship, termed the Fundamental Error of sampling, enables an optimum subsampling protocol to be defined for the sample preparation and assaying. However, the actual sample collection method, whether drilling or trenching, must be correctly selected and the sampling grid should be optimised. The relative costs and benefits of various alternative sampling methods and grids can be determined using the method discussed. The use of the grade control data can also be optimised. In the past ore and waste boundaries were often defined using a linear interpolation algorithm that smoothed the data (such as polygonal, sectional, inverse distance squared or even kriging methods). Frequently the relative impact of ore loss and dilution could not be estimated. Conditional simulation to generate equiprobable alternative maps (realisations) can now be adopted to address these issues. A transfer function is then used to evaluate the similarities and differences between the maps. The Ore Block Optimisation (OBO¬) process is a transfer function that produces a three-dimensional model of the optimal ore block outlines. This provides a clear guide for the mining geologist to refine and mine. The nature of the transfer function and the inputs and outputs are discussed. In the past, reconciliation has been the `acid test' for any grade control system. Any ore blocking method based on conditional simulation can make use of the exhaustive data set to ensure that reconciliation between prediction and production will improve significantly. The OBO¬ method provides a guide to the mining geologist to ensure that the best ore blocks are mined. Misclassification between ore and waste is reduced, ore loss and dilution are minimised (and are measurable) and ore is optimally assigned to stockpiles of various cut-off grades. These advantages significantly enhance mine profitability and control of the mined grade.

Jan 1, 1997

By Smart RST C, Johnson NW, Ralston J, Griffin LF

At the Copper Concentrator of Mount Isa Mines, the largest diluent of the copper concentrate is liberated fine pyrite. Laboratory flotation tests carried out as a function of grind and flotation Eh in combination with surface analysis by X-ray photoelectron spectroscopy (XPS) have identified the major mechanisms of iron sulphide flotation. It was found that a significant proportion of the iron sulphide minerals had surface coverages of graphitic carbon, sufficient to impart moderate hydrophobicity in the absence of collector. A smaller, but economically significant proportion of chalcopyrite was also affected by the graphitic carbon coating. Two methods were tested to reduce the impact of the natural floatability of the iron sulphides on concentrate grades. 1. Depression through the use of organic depressants. 2. Preflotation to remove the "naturally hydrophobic" iron sulphides (flotation independant of Eh ) prior to chalcopyrite flotation. Preflotation was tested at the pilot plant scale. It was found that the amount of chalcopyrite reporting to the preflotation rougher concentrate could be minimised through flotation at a mildly reducing Eh by the use of nitrogen as the flotation gas to maintain the low Eh conditions resulting from grinding. The preflotation rougher concentrate was upgraded to an iron sulphide concentrate or a low grade copper concentrate.

Jan 1, 1991

By J Krahn

In designing climate exposed soil structures such as caps and covers over mine waste it is necessary to include the wetting and drying influences of the local climate in order to accurately predict the net water, vapour and oxygen fluxes across the ground surface and through the base of the covers. The most advanced evaporative flux modelling tools currently available to practitioners have been limited to rigorous one-dimensional models (ie SoilCover) or semi-empirical two-dimensional models (ie Hydrus-2D). It is common practice to use the rigorous one-dimensional evaporative flux model results to develop a surface boundary function that can then be applied within a saturated/unsaturated two-dimensional model. However, this is not an ideal situation and results in a further approximation of the real system being modelled. This paper will highlight the use of a new modelling tool, VADOSE/W, which brings existing, rigorously formulated evaporative flux theory into the familiar setting of a two-dimensional model. The model is enhanced for simultaneous two-dimensional oxygen gas transport analysis, which has direct application in the mine waste industry. A key focus of the paper will be addressing the limitations of one-dimensional analysis for cover systems on sloping and hummocky terrain.

Jan 1, 2003

THE object of this paper is to offer some suggestions to assist metallurgists to supervise the operations of flotation plants. We do not yet thoroughly understand what "flotation" is or "why minerals float" and all attempts that have been made to explain the phenomena have been based on theory or imagination, and have not been capable of substantiation by practical demonstration, or even by laboratory tests; but it is wellknown that particular minerals will float in a liquid under certain specified conditions, and that some other minerals will not float under those conditions, and that, if a mixture of the two classes of minerals be subjected to those conditions, there will be separation of the minerals, of which one class will float and the other will remain unfloated as a residue. The duty of the flotation expert is to so control the operations and the conditions of the liquor as to obtain the best commercial result from the ore he is treating. The chief controlling factors in a flotation plant appear to fall under the following eight headings, all of which are important:1. Crushing.2. Rate and regularity of feed.3. Density of pulp.4. Temperature.5. Addition agents.6. Condition of circuit liquor.7. Agitation.8. Aeration.

Jan 1, 1920

More and more coal in Australia is extracted by underground mining methods especially by longwall mining. These methods can be particularly sensitive to relatively small-scale structural discontinuities and variations in roof and floor rock character. Traditionally, information on these features has been obtained through drilling. However, this is an expensive process and its relevance is limited to the immediate neighbourhood of the boreholes. The geological uncertainty remains. Seismic surveying, especially by 3D seismic, is an alternative tool for geological structure delineation with growing credibility. In fact, it is one of the most effective geophysical methods available for identification of geological structures such as faults, folds, washouts, seam splits and thickness changes which are normally associated with potential mining hazards. Seismic data even can be used for stratigraphic identification. The information extracted from seismic data then can be integrated into mine planning and design. In this paper, we demonstrate computer aided interpretation techniques for maximising the information from seismic data and illustrate the ability of seismic reflection methods to resolve localised geological features. Both synthetic and real seismic data obtained in recent 2D and 3D seismic surveys from Australian coal mines will be used. Compared with results obtained with drilling programs, the structural definitions from seismic are of unprecedented quality.

Jan 1, 2002

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

The process of refurbishment is not a precisely defined one. It is under- stood to mean an upgrading of a plant which is normally performed only once. The application of refurbishment in the field of materials hand- ling equipment poses particular problems because complex plants con- sist of individual components having quite different remaining service lives. For this reason, a systematic, proven procedure is proposed for the refurbishment of large materials handling equipment, designed to ensure economic implementation in accordance with the company goals. Rheinbraun2 has been using materials handling equipment since 1900, the largest units today being bucket-wheel excavators with a daily capacity of 240,000 bank cubic metres of overburden and a service weight of up to 13,500 t (metric tons). Since 1975, more than 50 large-scale refurbish- ment projects have been carried out in the company. In the process, refur- bishment has turned out to be the proven alternative to replacement of large materials handling equipment. Rheinbraun Engineering,3 a Rhein- braun subsidiary, carries out planning, consulting, and supervising work in the implementation of refurbishment projects in Germany and abroad. The most recent example is the refurbishment of Dredger 11 of the State Electricity Commission of Victoria in cooperation with Krupp-Australia, Melbourne.

Jan 1, 1989

By G Munro

he Melbourne City Link project will complete a missing link between two existing major freeways in the Melbourne road network, providing a much needed bypass of the Central Business District for through traffic. The project, which is being financed under a BOOT arrangement with the Victorian State Government, involves the upgrading of significant stretches of existing freeway and the construction of new sections involving viaducts and tunnels. The tunnel sections, which are the focus of this paper, are beneath residential and business areas, the Yarra River, the Royal Botanic Gardens and significant sporting facilities where surface construction would be either impossible or unacceptable (reference Figure 1). The shorter, 1.62 km west bound Domain tunnel comprises two cut and cover sections through Olympic Park then the Yarra River, the driven section of 0.68 km length and exits through a common cut and cover section with the east bound tunnel under St Kilda Road and Sturt Street. The longer 3.76 km east bound tunnel commences at the common portal, through cut and cover under St Kilda Road then 2.86 km of driven section before exiting at a cut and cover section at Burnley. The longer Burnley tunnel has an access and ventilation shaft at approximately its mid point.

Jan 1, 1999

This paper presents the water management plan of the Mae Moh Project in the North of Thailand, which includes a large lignite opencast mine and thermal power plants. Lignite production will increase from the present 5.5 million tons per annum to approximately 20 million tons per annum by 1995 when the pit area will be about 20 sq.km. and the depth at over 300 meters. Seven power plants are proposed of which two are under construction. The total capacity to be installed is 2,925 MW. The principles considered for water management are firstly flood protection, including drainage of the mining pit and diversion of the Mae Moh stream away from proposed future mining areas; and secondly, a plan to meet the water requirement of the thermal power plants, while maintaining downstream supplies for irrigation and other purposes. The limited annual run-off of Mae Moh and Mae Chang watershed basins are inadequate for the proposed power plants. A study has been prepared to compare two approaches, namely conveying water from remote watersheds to meet the water requirement of the power plants up to total installed capacity; or by limiting future total generation, at the existing site, to only 2025 MV.

Jan 1, 1988

By E Wan, K Stokes

Since 1978, the nickel concentrator at Leinster has been subject to continuous change. In 1971 a significant nickel sulphide deposit was discovered on Leinster Downs Station, within three years the extent of the deposit was determined. In 1978 the Agnew Mining Company began production of nickel concentrate from the Perseverance Mine and continued to do so until production ceased in 1986. In 1988 WMC purchased the mothballed project and began the first phase of many expansion initiatives. Milestones in the life of Leinster have included:open cut mining of the Perseverance orebody and the discovery of the RockyÆs Reward orebody, as well as the metallurgical challenges in treating each of these; underground mining at both Perseverance and RockyÆs Reward; construction and commissioning of the WMC grinding and flotation circuits; variations in the reagent schemes, including the introduction of æliquidÆ reagents; development of mill linings to reduce maintenance; circuit re-configuration and simplification; development of Harmony open cut; strategies for increasing throughput at the drier; and changes to tailings facilities to cope with increased throughput. This paper outlines the steps which have been required to expand the Leinster Nickel Concentrator from 650 000 tpa to 2.5 Mtpa and those steps which will be required in the future.

Jan 1, 2000

By McDonough RJ

Mechanical agitation is the preferred system for Carbon-in-Pulp processes. Agitator design requires an understanding of the relationships between energy, shear and flow and the nature of shear rates and shear stress distribution in an agitated tank. Laser techniques are useful when studying these phenomena. The alternatives are open impeller agitation or draft tube circulation. Each has advantages and disadvantages but both require careful choice of impeller and system geometry. Overall the draft tube circulator is the more attractive in many cases. Open impeller agitators are designed in accordance with established procedures for mineral slurries taking due account of shear effects in tanks containing carbon. Preferred tank proportions are 1:1. Circulator design methods were developed in the alumina industry before being applied to CIP processes. Optimum draft tube diameter is critical to power requirements. The overall system must be designed as an axial flow pump operating in a closed circuit. Such a system exhibits quite characteristic behaviour which requires an impeller of varying pitch angle and aerofoil section for best stability and efficiency.' Tank height may be 2 or more times diameter. Resuspension of settled solids can be assisted by a series of slots in the draft tube. These slots have the secondary effect of stabilizing hydraulic behaviour and reducing installed power requirements.

Jan 1, 1982

By P Elliott, D Pershke

In a minerals processing context, sustainability is about using natural resources more efficiently to achieve maximum economic benefits with minimal environmental impacts. It embodies five overarching themes, which the paper will illustrate with practical examples from Australian minerals processing plants. These are:resource utilisation and materials efficiency,process waste reduction and enhancement of co-product values,reduction of water use and impacts,reduction of energy requirements and greenhouse gas emissions, andenhanced control of minor elements and toxic materials. Sustainability could be embedded profitably in minerals plant design in three dimensions: 1.technology,2.design, and3.operations. This presentation discusses a set of principles that could be applied to minerals processing technologies and provides an outline of sustainability assessment and opportunities evaluation tools. The application of the tools is illustrated through a case study by analysing a suite of nickel processing technology routes. The analysis reveals that current generation of nickel processing technologies do possess real potential to emerge as sustainability champions in integrated processing of nickel ores and concentrates, if they are designed, engineered, and operated for sustainability and adapted effectively to site specific constraints and opportunities. The paper will address data gaps and uncertainties regarding the impact of scaling up of pilot-plant performance, and provides strategies to overcome them.

Jan 1, 2006

In southeastern China, offshore Tertiarybasins are buried underneath the broad continental shelf areas from Taiwan to Hainan Island. These basins bear relatively similar characteristics of structure, stratigraphy and tectonics. Based on age and tectonic framework, these Tertiary basins are divided into two groups of Paleogene basin and Neogene basin (Fig.1 and 2). However, observations of extensional structures indicate that the Paleogene basins are rift basins; and the predominant structural features are NE-SW trending half grabens and fault blocks. In a regional scale, these half grabens and adjacent uplifts represent a horst-and-graben structural style. Neogene basins are downwarp basins lying on the tilting continental shelf. Late Tertiary sequences are relatively undeformed but locally with minor folding and thrusting during the Pliocene-Pleistocene.Seismic stratigraphy and well data indicate that the Early Tertiary strata are commonly tilted and disturbed as nonmarine to marginal marine facies deposited in the wedge-shaped half grabens; the Late Tertiary strata are generally parallel undisturbed marine facies accumulated in the enlarged downwarp basins overlying the infilled half grabens. In general, three major regional unconformities formed during the Late Cretaceous, the Late Eocene and the Middle Miocene. Widespread extrusive basaltic flows are commonly associated with these unconformities.

Jan 1, 1990

By S Brunt

A new elution process has been developed for the recovery of gold thiosulfate from ion exchange resins. This is a synergistic system which utilises a base eluent, such as nitrate or trithionate, along with an additive that improves the elution of gold. The use of the additive enables lower eluent concentrations to be adopted, as well as weaker eluents such as chloride. With the chloride + additive system, complete gold elution can be achieved within 12 BV when utilising an eluent flow of 5 BV/h. When the eluent flow is reduced to 2 BV/h, complete elution is achieved within 8 BV. Similar results are obtained when using nitrate or trithionate as the base eluent. A copper pre-elution process has also been developed, whereby the majority of copper can be stripped within 5 BV prior to gold elution. This method is a significant improvement on the ammonia + oxygen pre-elution previously suggested. The development of a new analytical procedure based on ion chromatography with UV detection is also described for the quantification of polythionates in leach solutions and loaded on resins. This enables analysis to be carried out for resin-in- leach type processes where the polythionates are being formed in solution and simultaneously adsorbed onto the resin.

Jan 1, 2007

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

The Douglas mineral sands deposit is located 75 km north of Hamilton in western Victoria, Australia. The deposit was discovered in the late 1990s by Basin Minerals Limited and purchased by Iluka Resources Ltd in 2002. Prestrip mining commenced in December 2004, with ore mining commencing in August 2005. Douglas is the first of several projects being implemented by Iluka Resources Ltd in the Murray Basin, with all heavy mineral concentrate planned to be treated at the companyÆs mineral separation plant in Hamilton. The mineralisation at Douglas lies along the south-eastern margin of the Murray Basin. It is hosted by marine Pliocene Loxton-Parilla Sands and consists of three discrete deposits; Bondi Main, Bondi West and Bondi East. The mineralised sediments dip at a low angle to the west and lie unconformably beneath a veneer of top soil (50 - 100 mm) and subsoil (up to 600 mm) and between three to 12 m of overburden. The barren overburden, characterised by high clay content (<53 ¦m material) generally provides a stark contrast to the sandy ore, which is between 1 m (parts of Bondi East) and 15 m (Bondi Main) thick. Both overburden and ore are removed utilising standard dry mining techniques using both scraper-bulldozer and truck-excavator combinations. All ore is delivered to run-of-mine (ROM) stockpiles before being reclaimed by front end loader into the processing plant. Grade control at Douglas is based around visual dig control aided by high precision survey, which enables accurate reference to the resource drilling and block model data. Vertical excavator faces, inclined scraper faces plus regular test pits and trenches provide opportunities for in pit mapping and sampling. This data is used to refine not only the resource estimate for Douglas but also the drilling, interpretation and resource modelling methods used for similar deposits across the basin. The foundations of the geological reconciliation process at Douglas are the in pit surveys undertaken each time the mining fleet has completed building a ROM stockpile. These surveys and the subsequent interrogation of resource models enable robust estimations of the heavy mineral content of the stockpiles, which are subsequently used to predict the daily input grades into the plant during their reclamation. Reconciliation of this daily data is then undertaken at the end of each month against metallurgical production data and plant balances. Learnings and results from the reconciliation process are used to further refine subsequent resource models and modelling methods.

Jan 1, 2009

By T Sirinawin, R H. Murfitt, W Shywolup

The Bong Mieu Project lies within the Pre-Palaeozoic Kontum Craton near the southern margin of the regional Phuoc Son û Tam Ky Suture. The Suture and accompanying Truongson Fold Belt of Indosinian age host significant gold and base-metal bearing districts including OlympusÆ other project at Phuoc Son to the west of Bong Mieu and OxianaÆs Sepon project in Laos. The Bong Mieu Project is located some 90 km south of Da Nang and some 30 km south-west of Tam Ky, the provincial capital of Quang Nam province in central Vietnam. The project area is covered by an Investment Licence of some 30 km2 which was granted in 1991 and a mining permit of some 365 ha granted in 1992. Several mesothermal, gold-silver deposits with assigned resources are present on the property. Deposits with assigned resources contain some 615 000 ounces of gold in situ. These are at Ho Gan and Ho Ray which are potentially exploitable by open-pit mining and Nui Kem which is potentially exploitable by underground mining. Newly discovered extensions to the known deposits at Ho Gan, Ho Ray and Nui Kem, and several other new prospects, are currently being investigated by drilling. The Ho Gan mineralisation is of mesothermal, shear and shear breccia quartz vein, as well as intrusive breccia hosted style. Nui Kem mineralisation is of mesothermal, shear and shear breccia quartz vein style. The Ho Ray mineralisation is of skarn (gold-bismuth-tungsten) and lesser quartz vein style. The deposits straddle and flank the east-west trending Bong Mieu Anticline which trends through the central portion of the Investment Licence. In this paper the geology of the deposits, details of resources, results of recent exploration on the Investment Licence and recent engineering and mining studies at Ho Gan are briefly reviewed.

Jan 1, 2004