Search Documents

By Doig ID, Phillips HR

As a prelude to studying the sorption desorption and permeability behaviour of coal cores in a triaxial stressing rig using sorb- able gases, the air permeability of typical cores was measured. Lump coal samples were obtained from three gas-troubled collieries in Queensland and New South Wales. These were cored in the laboratory and a simple laboratory permeameter employed which accepted 38 x 40 mm cores in a thick rubber sheath. Air pressure of 500 kPa was applied outside the sheath to provide suitable sealing between the rubber and the coal. Differential driving pressures up to 100 kPa were employed and the air flow measured by displacement of water columns in inverted graduated cylinders. Flow measurements accurate to + 2% could thereby be achieved. Coal lumps were cored both parallel and perpen- dicular to the bedding plane, and were observed prior to measurement for any notable features, in particular for the presence of fissures. Between samples an overall variation of from 100 milliDarcy was found in Appin, Westcliff and Leichhardt coals. Significant variation was observed both from section to section of a core and between regions of a

Jan 1, 1982

By Snowden C. T

B Lens Main is a scheelite orebody with an average dip of approximately 15¦ and thickness ranging from 1.5 to 6.0 m. The orebody is overlain by a banded section of ore and waste which tends to slab off if left unsupported. It was originally planned to mine a large portion of this orebody by room and pillar methods, with existing diesel trackless equipment. This, however, proved unsuitable for a number of reasons and the smaller scale method of slot stoping with hand machines and scrapers was employed. The following major problems were encountered. 1. The method was new to the mine and the work force, and had to be commenced quickly using existing or easily obtainable equipment. This is gradually being overcome by training, modification of procedures and introduction of more suitable equipment. 2. The slabbing from the hanging wall had to be controlled, either by support or by mining this low grade section and accepting the resultant dilution. This has been approached in a number of ways, depending on conditions and the method will have to be further modified as different conditions are encountered in new areas.

Jan 1, 1977

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

While South Africa is well endowed with mineral resources, it is generally accepted that its future will be determined more by the development of its human resources than its mineral wealth. The country has throughout its modern history suffered from an over-supply of unskilled labour and a shortage of skilled and professional manpower. There has furthermore always been an over-reliance on Whites as an internal source of professional manpower, supplemented by immigration wherever possible. Better utilisation of other population groups in professional positions has been hampered by the general lack of education and training among such groups. Although many problems still remain, there are emerging trends which are likely to positively affect the training of professional manpower in the future. The direct and indirect influences that are likely to affect professional training at the macro level include 1. government policy and objectives in respect of manpower education and training, 2. the emergence of technikons as fully- fledged tertiary education institutions, 3. demographic trends in South Africa as they pertain to education, 4. political and statutory developments in the country, 5. industry involvement in tertiary education, and 6. professional registration.

Jan 1, 1986

By S Sineva, E Jak, M Shevchenko, D Shishin

This study represents a part of comprehensive research aimed at integrating nickel into a thermodynamic database constantly developed at Pyrosearch. The behaviour of Ni in calcium-ferrite slags is considered. An integrated approach combining experimental and thermodynamic modelling methods has been employed to predict phase equilibria in the NiO-CaO-FeO-Fe2O3 system under oxidising conditions and in equilibrium with the metal FeNi phase. The compositions of liquid slags and coexisting solid solutions have been determined through the analysis of equilibrated and quenched samples by electron probe microanalysis technique (EPMA). The research results are presented in the form of liquidus projections on the corresponding phase diagrams, considering both oxidising and reducing conditions. The solubility of Ni in spinel, dicalcium ferrite and calcium oxide as well as solubility of Fe and Ca in Ni monoxide, have been examined under several atmospheric conditions. Additionally, the compositions of the NiO-FeO monoxide in equilibrium with metal phase have been studied. The experimental data not only support the outcomes of thermodynamic modelling but also validate the parameters of the applied thermodynamic models, thus confirming the reliability and accuracy of the integrated approach.

Aug 21, 2024

By Eren H

For a hydrocyclone of fIXed geometry, DC, Di, DO and ? are constants, the variable parameters affecting the performance are Qi, Fi, Du and H. (See Appendix 2 for definition of symbols).The relationship between d50c, Qi, Fi, Du and H gives models which can effectively be used for performance predictions. Such models have already been established by Lynch et al and by Plitt.These models have been tried in a limited manner under continuous operating conditions for on-line cowol. For on-line control effective and accurate instrumentation is required for which a new set up is proposed. Using this set up, a new model was established. A feature in this model is that deviations from the norm of operational parameters affecting d50c were considered. It is shown that these deviations generated by the disturbance of one or more of variations in the parameters, can be monitored by a computer and suitable signals generated to control servo mechanisms for restoring the required d50c value.The logic followed in developing the computer software is described and the application of the model is indicated.

Jan 1, 1990

The Lennard Shelf Operations owned by Western Metals Ltd evolved from the Cadjebut Zinc Lead Mine (BHP) in August 1994. Original production of 0.5 mtpa will rise to 2.0 mtpa at the end of 1998. Employees work a multiple of fly-in/fly-out (FIFO) rosters from the Kimberley region and the WA Capital. The three underground mines, treatment and services departments will employ approximately 300 people by the end of 1998. The expansion of the Lennard Shelf Operations as a remote mining location was based on a fresh look at management systems and employee rosters which were generated from many years of mining experience. This paper will endeavour to summarise these experiences and analyse some of their outcomes. Dealing with several mining methods, engineering difficulties, logistical problems and climate extremes, the Lennard Shelf Operations has managed social/employee issues with excellent results. Much time has been spent to get this correct for the Lennard ShelfÆs own set of circumstances. Employees and associated companies must expect continuing changes and improvement as Western Metals strives to continually improve its management systems and employee rosters.

Jan 1, 1998

By T Mizuta, D Ishiyama

The Vienna Wood hydrothermal is hosted by mid-oceanic ridge type basalt in graben morphology and is located in the Central Manus Basin. The hydrothermal field is about 300 metres in diameter and consist of a sulphide mounds and tall huge death and active chimneys. From the three distinct ore types collected from the Vienna Wood site, the dominant ore minerals recognised are pyrite, wurtzite, sphalerite, chalcopyrite, Fe-oxide and gangue minerals of anhydrite, gypsum, barite and silica. The consistencies in the paragenetic sequence and in the spatial distribution of the sulfides across the three ore types suggest that similar hydrothermal process exist across active and death chimneys. Fluid inclusion studies reveal a homogenisation temperature of 190-260¦C and an average salinity of 5.1-5.4 wt per cent NaCl equiv. The pH of the hydrothermal fluid ranges from 4.2 to 6.1. Bulk chemical analyses indicate that the mineralisation in the Vienna Wood can be classified into the Zn-(Cu-Pb) type of mineralisation. The tenors of the ore and mineral assemblage resemble those of the Mid-oceanic ridge system and ancient ophiolite hosted massive sulphide deposits of Cyprus and Oman.

Jan 1, 2002

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

By D E. Freeman, M A. Somerville, B M

A program of re-planting native mallee trees, which can be harvested on a short rotation cycle, has been initiated in Western Australia to counteract increasing soil salinity in the wheat belt region. Large volume applications for the wood products generated by these plantings are required to improve the returns to farmers. The metallurgical industry is a large-scale user of carbon, and a project was carried out through the Centre for Sustainable Resource Processing to investigate the use of mallee-derived carbons in metallurgical processes. The use of renewable carbon sources, such as charcoal, to replace fossil carbon has the additional benefit of reducing the net CO2 generated by the metallurgical industry. Experiments were undertaken to assess the performance of mallee derived charcoals as reductants for the solid state reduction of ilmenite and for iron ore bath smelting. Rotary drum reduction tests showed that the reduction rate of ilmenite with the mallee charcoal was approximately twice that of Collie coal at the same fixed carbon/ilmenite ratio in the bed. Iron bath and slag bath injection tests demonstrated that the mallee charcoals dissolved readily in molten iron carbon baths and reacted efficiently with iron making slags.

Jan 1, 2006

The scope, pace and depth of mining is creating a need for improved ground control strategies to meet mine safety standards. Ground control and associated conservation problems relating to subsidence and the disposal of mining and metallurgical wastes can be resolved by mine filling with selected reject materials. The lack of suitable criteria to evaluate the applicability of such materials and especially cemented forms of fill is considered. Sulphide wastes, which are prone to oxidize, and cement are inexpensive mine fills, but their incorrect use can give rise to problems which are briefly described. Research work concerned with the utilization of sulphide wastes such as mill tailings, to produce fill with self-cementing properties has shown that the development of cohesion and strength is attributable to natural oxidation processes controlled by the physical and chemical composition of the fill mass. The cementing is caused by a number of oxidation products, and is most effective when the mineral pyrrhotite is present. The concepts of fill design are outlined and various criteria for assessing durability and deformational properties are proposed. Specimens prepared in the laboratory are capable of attaining unconfined compressive strengths up to 28 MN/m2.

Jan 1, 1973

Natural gas was introduced to the Melbourne reticulation system in April 1969 and since that date sales to industrial consumers in the Gas & Fuel Corporation of Victoria area of supply, have increased by over 50% This increase has occurred despite the fact that the areas in which the new fuel is available have been dependent on the progress of the conversion operation from manufactured gas. The half way mark for conversion was reached in May 1970. The reason for the adoption of natural gas by industrial users is usually the result of objective financial analysis leading to the conclusion that the new fuel will give the lowest overall production cost. Many factors are involved in such an analysis of which the price of the fuel is only one. Amongst other important elements in the cost calculation are:- -ò òò -(1) The effect of fuel on product quality (2) Maintenance and handling costs for alternative fuel. In addition to economic gains for the individual user, the use of natural gas should benefit the whole community through its effect on such things as, air pollution and overseas balance of payments.

Jan 1, 1970

Near Kangiara in south eastern New South Wales, Australia, a number of polymetallic (copper, lead and zinc, with minor silver and gold) mineral deposits occur within a relatively broad volcanic rock belt, intercalated with limestones, sandstones and shales, of Silurian age. The Kangiara deposit was the most significant for the region.Adjacent to the Kangiara deposit, the unaltered country rocks are more rhyolitic than elsewhere in the volcanic rock belt, and the mineralization is accompanied by silicification, chloritization, sericitization and argillization. The host rocks typically contain a higher K20:Na2O ratio than the volcanic rocks not associated with mineralization.In the Kangiara deposit the mineralization consist of massive (in part banded), fragmental, disseminated and vein-type copper-lead-zinc ores, with the massive and fragmental types divisible into pyrite-rich, chalcopyrite-rich and sphalerite-galena-rich varieties. With respect to this mineralogy, the ore textures and sulphur isotope compositions the deposit can be compared to the stratiform mineralization associated with Silurian acid volcanic rocks at Woodlawn, Captains Flat and elsewhere in the Lachlan Fold Belt, as well as the Tertiary Kuroko deposits of Japan.

Jan 1, 1990

With the use of 36 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt Lyell Mining & Railway Co, it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5000 feet of boring the total cost of new parts is noted on this line (see Figure 1). Thus at a glance it is possible to see the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this clifficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component.As before the cost of new parts are taken at each 5000 feet bored (see Figure 2).

Jan 1, 1994

By N Voller, A Ishmurzin, G Hackl, M Wu, A Kharicha, M Chintinne, C M. G Rodrigues, A Ludwig

Slag fuming (SF) is a critical process for recycling zinc-containing slags, but the corrosive nature of molten slag poses challenges to the reactor durability. The freeze-lining (FL) technique offers a solution by forming a protective layer on the reactor wall. It requires intensive cooling using watercooled jackets, which can stabilise the FL while compromising the energy efficiency of the process. This study presents a computational fluid dynamic (CFD)-based model to optimise the SF process by considering FL formation and its impact on heat transfer and reactor wall temperature. A volumeof- fluid (VOF) model is coupled with a mixture continuum (MC) solidification model to capture the intricate multiphase flow dynamics within the SF furnace. Two FL types are considered: FL solidifying on the reactor wall in the slag bath region; and FL solidifying on the reactor wall in the freeboard region. The FL of the first type forms when the slag temperature drops below liquidus temperature. The FL of the second type only forms when a splash-induced slag droplet collides with the freeboard wall and solidifies. A series of splashing events are necessary to coat the freeboard wall. The simulation was run until a global energy balance was reached. This means that the heat losses from the water-cooled jacket, bottom wall, outlet and fuming balance the heat gains from the hot gas injected through the submerged plasma torches. The increase in FL thickness, due to its low thermal conductivity, reduces the heat losses through the reactor walls. The calculated FL thickness and heat fluxes were in good agreement with industrial data, validating the model’s credibility. The simulation results provided valuable insights into the fuming process, including slag bath temperature evolution, slag splashing dynamics, FL formation patterns, local heat fluxes through the reactor wall and overall energy balance. These findings can inform process optimisation strategies to enhance the energy efficiency and sustainability of SF operations. The authors have built a prior version of the model framework and applied it to simulate FL formation in an electric smelting furnace (ESF). The results from both the ESF and the current SF highlight the applicability of such model framework to a range of industrial processes involving FL formation. This model framework can ultimately contribute to more energy-efficient and sustainable industrial operations.

Aug 21, 2024

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987

By C J. Ptacek, J G. Bain, D W. Blowes

The passive interception and in situ treatment of groundwater using permeable reactive barriers (PRBs) has, within the past decade, become an accepted remedial approach to the control of plumes containing dissolved organic and inorganic contaminants. Since the first applications of the technology in the early-1990s, there have been several field-scale PRBs that have provided excellent treatment of dissolved metals in groundwater. Additional commercial applications and demonstration projects continue to be developed. Three field-scale applications and supporting laboratory columns have shown that several thousands of milligrams per litre of sulfate, more than 1000 mg/L iron, and several tens of milligrams per litre of other metals can be removed from groundwater by PRBs that promote sulfate reduction. The reactive materials, which incorporate various forms of organic carbon, promote microbially mediated sulfate reduction, the generation of hydrogen sulfide, and the subsequent precipitation of sparingly soluble iron and other metal sulfide minerals. Effective performance has been achieved by PRBs installed at a mine-tailings impoundment in 1995 (Sudbury, Ontario) and at an industrial facility (Vancouver, British Columbia). These PRBs have removed iron and other metals from groundwater. Similar materials were also used to create reactive layers within test cells directly in a tailings impoundment in 1999 (Timmins, Ontario) with the objective of removing iron and sulfate from the pore water before it migrates from the tailings impoundment. Zero-valent iron (ZVI) has been shown to provide excellent removal of chromium (VI) in a PRB, which was installed at the US Coast Guard facility in Elizabeth City in 1996, by reduction and precipitation reactions. Laboratory tests have also shown that ZVI reduces As(V) to As(III), which is subsequently removed from solution by co-precipitation with iron oxyhydroxides. In groundwater containing sulfate, ZVI and mixtures containing organic carbon can promote sulfate reduction and the subsequent precipitation of sparingly soluble arsenic and other metal sulfides. A trial PRB system was installed in 2001 and was shown to attenuate arsenic and other electroactive metals in groundwater at an industrial facility in northwestern Ontario. Basic oxygen furnace (BOF) slag, a waste material generated by the steel industry, has shown excellent potential for the removal of phosphate, elements such as arsenic and water-borne pathogens from groundwater in field and laboratory tests.

Jan 1, 2003

By J Rutter, M NoppT

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. Ridgeway is an underground sublevel cave (SLC) operation mining approximately 5.6 Mt of gold-copper ore per annum. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Drawpoint recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Grade control at Ridgeway has been based upon sampling the ore from SLC drawpoint bunds using 15 kg grab samples combined to form 30 kg samples prior to assay. This large sample size was selected in an attempt to representatively sample the coarsely-sized broken ore, the samples collected having a nominal diameter of about 130 mm. The assay results for gold and copper from these samples are extremely variable and the usefulness of the results has been questioned by the mine, particularly given the onerous and OH&S hazardous activity of handling large sample masses. Granulometry testwork at Ridgeway confirmed the extent of the relationship of decreasing sample grade variability with particle size. Based on this relationship, drawpoint sampling tests were carried out using 9 kg samples sieved to -45 mm at the drawpoint site. The gold and copper results from the finer 9 kg samples were significantly less variable than those from the normal, coarser 30 kg samples. The variance reduction was similar to that predicted from broken ore sample theory for the selected sample mass and nominal particle size. This relationship therefore allowed Ridgeway to assess the sample mass and particle size required to achieve a particular precision. In addition to improving the precision, the reliability of assay results from smaller samples from the fine particle fraction for drawpoint control depends on the accuracy of the results. The assumption is that the grade of the finer ore is similar to that expected from the lot, or that if a bias exists, then the extent of this bias is acceptable and consistent enough to be accounted for in the grade control system. The distribution of grade with particle size and the reconciliation of drawpoint sample and mine results is currently under investigation.

Jan 1, 2005

Samples of the feed, underflow and overflow mediums from dense medium cyclones operating at low separation densities in eight commercial coal washeries were sized and analysed, to obtain comparative cyclone classification performance curves for the magnetite, shale and coal components in the circulating medium. The resulting component classification curves indicated that the dense medium cyclones hydraulically classify the magnetite and the shale to the underflow with a Stokesian size and density relationship at these low medium densities, ie the shale curve was shifted parallel to and appropriately coarser than the magnetite curve because of the lower density of the shale. However the lower density coal reverse classified to the overflow (ie away from the cyclone wall) with a similar Stokesian relationship. By correcting the magnetite and shale classification curves for the bypass inefficiency to underflow, and similarly correcting the coal classification curves for the bypass inefficiency to overflow, the corrected classification curves for the magnetite, shale and coal were reasonably parallel (considering that the coal has a range of densities). Using a value of five for the density of the magnetite, the displacement of the shale and coal curves corresponded to densities of 2.27 and 1.38 respectively for one circuit, although the data was not as good for the other circuits. This reverse classification mechanism was confirmed in a 140 mm diameter laboratory dense medium cyclone circuit using low density (1.20 - 1.30 RD) tracers, sized from 0.25 to 2 mm. These classification performance curves were corrected for bypass ineffiency (as above). The corrected curves were parallel and displaced according to tracer density, even though the lowest density tracers were reverse classified to the overflow. The data indicate that the rates of classification of all particles could be described by the same Stokesian relationship, regardless of the direction of travel, except for a narrow band at the partition density. Particles heavier than the partition density classified to the underflow, particles lighter than the partition density reverse classified to the overflow and particles identical to the partition density were not classified at all. Consequently it should be possible to simulate partition in dense medium cyclones, operating under free settling low density conditions, with a simple cyclone classification model, provided the partition density can be accurately calculated from, or correlated with the cyclone feed, underflow or overflow pulp densities. The tracer partition performance in the laboratory cyclone was an inverse function of the tracer particle size, as proposed by King and Juckes (1984) for medium/coal ratio in low density medium systems. Their sized coal data was parallel, with lower partition values due to a higher energy cyclone. Partition data with similarly sized tracers (Scott, 1988) showed a parallel shift to higher partition values due to the separate effects of higher viscosity medium and a larger diameter lower energy Cyclone.

Jan 1, 1993