Search Documents

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By McGuckin P. H

The Cadjebut orebody is a MississippiValleyType (MVT) zinc-lead deposit, and is located approximately 80 km southeast of Fitzroy Crossing in the Kimberley region of Western Australia. It is one of five zinc rich orebodies discovered by BHP Minerals in the region.The participation in the Cadjebut Joint Venture is BHP Minerals limited (Manager), 58 per cent and Billiton Australia Limited, 42 per cent.The mineralisation is contained in gently dipping dolomitised limestone sediments (part of the Lennard Shelf carbonate sequence) with an orebody width of between 60 and 120 m and a strike length of approximately 3 km. The deposit consists of two thin, stratabound shallow dipping orebodies, one overlying the other, to provide discrete but not independent mining areas. The orebody contains approximately 2.1 million tonnes of recoverable ore at an approximate grade of 12 per cent zinc and four per cent Lead.

Jan 1, 1992

A substitute for rutile can be produced by leaching natural or pre-treated ilmenite in hydrochloric acid. Ilmenite in its natural form is an extraordinarily inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite so that it can be leached with dilute hydro- chloric acid (=2O% w/w) can be enhanced by pre-treatment steps of oxidation and re- duction. The temperatures at which oxidation and reduction are carried out have an effect on both the kinetics of these steps and the leaching kinetics and optimum temperatures for oxidation and reduction are 950 and 850¦C respectively. The mechanism of leaching of iron from pretreated ilmenite and the effects of rate of agitation, temperature, acid con- centration and addition of ferrous chloride to hydrochloric acid on leaching kinetics and production of fines are discussed in the paper.

Jan 1, 1984

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

By Mowat BA, Leach TM

The Morobe Goldfield in Papua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23t) and Edie Creek (40 and geological resources have been established at Hidden Valley (780, Kerimenge (360 and Hamata (30t). Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.

Jan 1, 1995

Taxation is a major factor in evaluating mining project developments. The availability or otherwise of effective tax relief for project expenditures can have a crucial bearing on the decision to proceed with a project. The special position of the mining industry is recognised within the Income Tax Assessment Act (the "Tax Act") by special legislation, namely Divisions 10, 1OAAA and 10AA. The legislation both extends the scope of items which are eligible for deduction and affects the timing of deductions. Generally, the legislation separates expenditure into 3 categories: 1. Expenditure on exploration 2. Capital expenditure on the development and the running of the mine; and 3. Facilities used in the transport of minerals. Companies evaluating a project should carefully analyse their proposed expenditures, allocating them between these categories so as to identify potentially non-deductible expenditures and to determine the period over which tax relief will be Obtained.

Jan 1, 1983

The non-metallic minerals, excluding the construc- tions and fuel materials have for long been the "poor relations" of the Mining Industry of New South Wales. The State is self-sufficient in only a few of the industrial minerals and is almost completely lacking in any of the essential fertilizers. The deficiencies must be met by imports from overseas and interstate and in fact New South Wales imports some quantity of every one of the non-metallics. For the year 1967 the value of non-metallic mineral production amounted to only $9,390,000 or less than 3.5% of the States total of $275,900,000 for all classes of mining and quarrying. In roughly the same period, the 1967-68 financial year, New South Wales imported non- metallic materials, valued at well in excess of $22,000,000 from overseas and over $2,000,000 from interstate sources.

Jan 1, 1969

Mining companies in Australia have grown in size and complexity over the past 20 years. The same period has seen exten- sive changes in the operating environment, with greater competition and intensified in- dustrial and social pressures placing new demands 'on mining activity. The new condi- tions require a management approach that emphasises strategic planning rather than operational efficiency. Strategic management evolves through four distinct phases, namely, financial planning, forecast-based planning, externally oriented planning and 'true' stra- tegic management. The most difficult transi- tion to make is from Phase 2 (forecast-based planning) to Phase 3 (externally oriented plan- ning) since management is often too involved in operations to find time to develop and main- tain a strategic orientation towards the mar- ket and competitors. Reorganisation of re- sponsibility for operations and improved op- erational processes enable management to concentrate on external opportunities.

Jan 1, 1980

The program, WASTRT 70, was set up specifically to handle the design of tunnel liners and underground structures where inter- action between rock and structure significantly affects the design. It may however be used for any mass/R.C. structure capable of being simulated by straight line elements between modes and with loading restricted to nodes. The analysis system adopts typical elastic/stiffness matrix methods. Two main mass/R.C. design segments are utilized (1) Design of section depth based on maximum required stresses and optimum steel/concrete ratios. (2) Design of reinforcement for a given section depth with concrete stresses given for mass and water code structures. Each design segment covers shear, minimum principal stress on ~ , heavy compression as per code (columns), heavy compression one-face steel (tunnel liners), tension and water code requirements for all moment/thrust/section depth ratios on rectangular sections.

Jan 1, 1976

This paper sets out a number of means by which professionals can reduce or eliminate the risk of professional liability whether as directors, employees, partners, independent consultants or contractors. A relationship between client and professional is commonly cited as an example of a fiduciary relationship: the professional "undertakes or agrees to act for or on behalf of or in the interests of' the client "in the exercise of a power or discretion which will affect the interests of that other person in a legal or practical sense."2 As a fiduciary, a professional must ensure that his or her exercise of power does not result in a position of ascendancy or undue influence over the client. Also, a professional must avoid situations where there is scope for even the perception of potential conflict between his or her professional duty to the client and his or her own Interest.

Jan 1, 1995

By Grieve BL

For a blast to be successful both heave and fragmentation must be satisfactory. Amongst the major factors influencing blasting are rock properties. This paper considers the effect of rock density on fragmentation and heave and how better results can be achieved in dense ore. Patterns which increase the heave and give better fragmentation are examined and the application of theory to the blasting of the Dales Gorge Haematite, density 4.2 - 4.5 t.m.,3 is then discussed. The drilling of staggered patterns instead of square patterns and a shallower 'V' initiation system has given better heave and fragmentation. This practice has re- duced backbreak and improved toe conditions; these factors have resulted in increased load ing rates. There has been an increase in the lump/fine ratio which is consistent with the theory although other factors such as ground conditions could have contributed.

Jan 1, 1978

By Bedford D. J

The post pillar cut and fill stoping method has been adopted by King Island Scheelite for the extraction of the main Dolphin orebody. The orebody is a massive, tabular deposit varying from 10 to 50 metres in thickness, and dipping at approximately 30¦ towards and under the sea bed. The mining method was selected for 1. maintenance of hangingwall support under the sea bed; 2. maximisation of first stage ore extraction; 3. flexibility of mining, allowing maintenance of grade and selective mining around waste bands within the orebody, and 4. compatibility of existing equipment both with stoping and the on-going underground mine development programme. Stope parameters were established on the basis of initial rock stress analyses, and since the undercut phase of mining the stoping programme has been monitored with various types of deformation measuring devices installed in a series of large diameter boreholes.

Jan 1, 1977

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

By Rivers CJ

The Brolga deposit is a Ni-Co enriched laterite, formed over intensly serpentinised peridotites of the Marlborough Block. Basement lithologies at Brolga consist predominantly of serpentinised dunite, with lesser massive serpentinite shear, gabbro and harzburgite. Investigation of the deposit has defined 17 different varieties of saprolite, ferralite (limonite), and ferricrete. Different combinations of these varieties form three distinct lateritic associations, the Hard, Soft and Dyke Associations. Recognition of key textural and mineralogical features in each association, an understanding of basement geology, and an awareness of current climatic conditions, suggest that: 1. both the Hard and Soft Associations have formed under relatively dry climatic conditions; 2. the Soft Association reflects much poorer groundwater drainage than the Hard Association; and 3. the Dyke Association has formed from a gabbroic basement, and has also been affected by restricted groundwater drainage, caused by poorly permeable marginal serpentinite shears.

Jan 1, 1996

By Thomas E. G

In the economic evaluation of any Australian mining project, changes in taxation can significantly affect viability. Australian tax laws, particularly in the period since early 1973, have undergone many changes which have led to shifts in the profitability of mining companies. This paper examines the sensitivity of a selected, broadly based sample of Australian mining companies to the changes that have occurred, or are reasonably likely to occur, in taxation legislation. In the past, tax systems have been altered for a variety of reasons, such as 1. reduction'in the impact of inflation 2. neutralization of incidence between different sections of the economy 3. as an incentive to encourage expansion and growth in a particular industry or area, and 4. increase in the real "take" of government. In this paper, conventional rate of return analyses are applied in a study of how profitability is affected under various taxation systems.

Jan 1, 1977

The patterns of occupational health pro- grammes in mining and metallurgy are discussed in relation to the impact of chemical and phy- sical hazards on the health of workers in these fields. Mining and metallurgy are quite unique in that their history and practice embrace virtually the total spectrum of occupational health problems and hazards as understood today. A panoramic concept of the possibilities would comprise the following fields: 1. The Pneumoconioses or Dust Diseases. 2. Physical stress due to exertion, and exposure to heat and humidity in deep mines. 3. The toxic effects of various metals in the mining of ore. The most obvious are lead, mercury, arsenic and manganese. 4. Diseases associated with mining. These include leptospirosis, ankylostomiasis and mycotic infections of the skin. 5. The Beat Diseases of coal miners working in narrow seams. 6. Illumination problems and miners nystagmus. 7. Geographical and climatic problems

Jan 1, 1975

By Abdurazakov A, Avrakhov A, Solozhenkin P

The flotation properties of acetic acids modified by xanthic and dithiocarbamic fragment in regards to copper and ferrous minerals and their noble metal containing ores have been investigated. The effectiveness of the co-using of these reagents with xanthates and dithiocarbamates has been shown, ie using of proposed reagent regimes for the flotation of Au-containing ores increases gold recovery by 4.2 - 4.7 per cent, and in the case of flotation of copper Re-containing ores copper recovery increases by 3.3 per cent, rhenium recovery - by 15.5 per cent. The mechanism of the action of these reagents has been explained by the data of UV and ESR-investigations of their sorption on mineral surface. The information on structure and properties of co-ordination compounds of some metals with (Diethyldithiocarbamato) acetic acid were used also for the explanation of flotation mechanism.

Jan 1, 1993

Extensive geophysical exploration and drilling operations have been: conducted in, South Central Queensland by Phillips Petroleum Company and Sunray DX Oil Company since late 1959. The main outlines of subsurface geology are now known, but many problems must be solved before a comprehen sine. picture can be presented of the geology and petroleum prospects e Interpretations to date suggest that -fiddle Paleozoic sedimentary rocks, probably, related to the Tasman belt of geosynclines, once extended. over. most. of the area An oro;eny 2.n late Paleozoic time, succeeded by deep pre-Pexmian erosion, removed the older sediments over large. areas, but Paleozoic sediments, were preserved from erosion in the Adavale and ancillary structur-a.l basins. Marine sediments of Devonian age are con-sidered prospective source beds for petroleum. Current work is directed toward finding favorable structure and reservoir beds to test the oil prospects of the area.

Jan 1, 1962

By Bratt G. C, Horsham T. R, Langlois D. R

Mercury is precipitated from weakly acidic sulphuric acid plant waste liquor at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited. Factors determining the choice of process and reagent, as well as details of process development including scale- up, and the time scale of implementation are outlined. The plant is designed for a maximum flow of 120 m3/h.of liquor containing mercury and saturated with sulphur dioxide. Mercury is precipitated by fluidised beds of aluminium pellets contained in lead columns. Liquor is then clarified with plate and frame presses. Experimental work on the mercury precip- itation reaction was conducted in three phases involving a scale-up of 100 times in equipment size. Extensive pilot filtration work was carried out on a 1 m2 press. Scale-up of 120 times was required for specification of plant filters. The basis of scale-up is outlined.

Jan 1, 1977

The patterns of occupational health pro- grammes in mining and metallurgy are discussed in relation to the impact of chemical and phy- sical hazards on the health of workers in these fields. Mining and metallurgy are quite unique in that their history and practice embrace virtually the total spectrum of occupational health problems and hazards as understood today. A panoramic concept of the possibilities would comprise the following fields: 1. The Pneumoconioses or Dust Diseases. 2. Physical stress due to exertion, and exposure to heat and humidity in deep mines. 3. The toxic effects of various metals in the mining of ore. The most obvious are lead, mercury, arsenic and manganese. 4. Diseases associated with mining. These include leptospirosis, ankylostomiasis and mycotic infections of the skin. 5. The Beat Diseases of coal miners working in narrow seams. 6. Illumination problems and miners nystagmus. 7. Geographical and climatic problems

Jan 1, 1975