Search Documents

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

The laboratory-scale reduction of fixed beds of iron ore pellets has been investigated over a range of experimental conditions. The effects of reduction temperatures, gas compos- itions and flowrates on 1) the rate of reduction and 2) the physical properties of the metallized products after reduction are being studied as part of a general programme aimed at the evaluation of the use of gaseous reductants for the direct reduction of Australian iron ores. This paper deals primar- ily with the effects of temperature on the rate of reduction using a H2/CO gas mixture. The physical properties of the metallized products such as strength after reduction, abrasion resistance and porosity are presented as functions of the reducing temperature.

Jan 1, 1974

By Lawson F

A rotating disc geometry has been used to provide a uniformly accessible surface for a kinetic study of the cementation of the metals cadmium, lead and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu/Zn and Cu/Fe systems for which the rection rate was found to be completely solution-phase mass-transfer controlled. When the amount of material deposited was greater than 0.2 to 0.4 mg/cm2 there was an apparent enhancement in e which is attributed to the formation of a roughened deposit. This same phenomeon was obseived in the Cu/Zn Cu/Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass ,..~sfer controlled.

Jan 1, 1970

The world is getting flatter through internet, mobile phone technology, relatively low cost travel, massive outsourcing of manufacturing to China and the transfer of company backroom operations to India. In the iron and steel industry, however, things will remain relatively the same with slow gradual improvements in technology; only the geographic location of plants may change over time. Or will it? The blast furnace smelting process has remained largely unchanged since 1828 when James Neilson came up with the idea of preheated air being delivered to the tuyeres. Likewise, oxygen steelmaking that takes molten iron from such blast furnaces has remained conceptually unchanged since Sir Henry Bessemer invented an air-based system in 1856. These two processes are the core of integrated steel mills that we know today. Typically such mills consist of coke ovens, sinter plant, blast furnace, oxygen steelmaking, continuous caster, rolling mills and metal coating lines. In the intervening 150 years the only real disruptive technology to the integrated steel mill has been the minimill. Based on the use of the electric arc furnace (EAF), in conjunction with a continuous caster and rolling mill, the term minimill is used because steel products are produced at down to one-tenth the scale required for economic operation of an integrated mill, with the EAF producing molten steel using largely scrap steel as its feed, as against transforming coal to coke (coke ovens), iron ore, coke and limestone into molten iron (blast furnace) and molten iron to steel (oxygen steelmaking). There are, however, a number of technologies in development that may cause a paradigm shift in the way steel products are produced and perhaps push the evolution of the minimill as a disruptive technology. Two examples are direct iron smelting, where iron is produced in a matter of seconds by injection of ironmaking feed materials into a molten bath, and thin strip casting, where molten steel is cast into 2 mm strip or less, in similar time. Both have Australian connections. A leading iron smelting technology is the HIsmelt« process, which has its first commercial application at Kwinana, Western Australia, where a joint venture of international parties, consisting of Rio Tinto and the Nucor, Mitsubishi and Shougang corporations, are in the stage of ramping up commercial production. The leading strip casting technology is the Castrip« process that arose from development work done by then BHP Steel, with IHI of Japan, at Port Kembla, New South Wales in the 1990s. Nucor followed this work up, building the first commercial plant for the technology at its Crawfordsville site in Indiana in 2001 and has recently announced an intention to build a second plant in the USA. While both technologies are only into the early stages of commercialisation they are likely to change the face of iron and steelmaking as we know it over the next 20 years. This paper elaborates on the technology of the two processes, why they could change the face of the iron and steel industry forever, what might drive the rapid change and what the changes may look like.

Jan 1, 2006

By E S. Souza, H Delboni Jr, M F. Calixto

This paper aims at presenting the results of laboratory, pilot plant and simulation studies for the design of the grinding circuit for the beneficiation of compact itabirites from the Conceitpo mine. Two alternatives were investigated, both utilising the current crushing circuit up to tertiary crushing. Under alternative #1, quaternary crushing was considered to produce the feed of the ball mill; under alternative #2, high pressure grinding rolls were selected to prepare the ball mill circuit feed. Pilot scale studies pointed towards the use of high pressure grinding rolls (HPGR). The circuit design was based on a throughput of 720 t/h, representing a nominal solids flow rate of 600 t/h, considering a design factor of 1.2, and P80 of 95 ¦m.

Jan 1, 2007

Mount Isa mine is the largest underground mine in Australia and is located 2,000 kilometres north-west of Brisbane. This mine has been in continuous operation since 1931 and in 1986/87 the silver/lead/zinc stream achieved the peak annual mining rate of 4.7 million tonnes. At present about fifteen different steeply dipping stratiform orebodies are being mined to maintain an annual production rate of around 3.0 million tonnes. Out of these, only two orebodies (2 & 5) are amenable to sub level open stoping (SLOS) type bulk mining methods. This year only 150,000 tonnes are scheduled from pillars and remnant areas but in future, more sources will be required to meet the budget production targets.

Jan 1, 1990

By Wenya X, Bingchen C

About 60 per cent of magnesite ores of Haicheng Magnesium Mine, due to their low grade, are not currently commercially exploitable. In this paper, the flotabilities of the main component minerals of the ores were studied in detail with ether amine as collector. Based on. these, a new technique of reverse-direct flotation with single etheramine as collector for the beneficiation of the ores was developed. It gave highly satisfactory results. On the basis of the calculation by means of CNDO/2 method, of the studies of the solution chemistry of magnesite and of the adsorption tests and Zeta-potential measurements, the key mechanism in the new technique about activating effect of Ca2+ on the flotation of magnesite was suggested.

Jan 1, 1993

By T J. McGavin

This paper examines the fire life systems implemented in two existing tunnels and discusses whether the standards used were appropriate. It focuses on the Terrace Tunnel as this upgrade and refurbishment is complete.The New Zealand Transport Agency (NZTA) manages six tunnels on the State Highway network with two of these built in the last seven years. The Terrace Tunnel, opened in 1978, was refurbished with modern fire life safety systems in 2010–2012. An interim upgrade of the Mt Victoria Tunnel, opened in 1931, was also carried out at this time.In present times, few existing tunnels have undergone significant upgrades and refurbishments. The Terrace Tunnel required: new power supplies, control buildings, lighting, wall panels and jet fans, a deluge system, emergency exit lights and way-finding lights, a public address (PA) system, a radio rebroadcast system, lane control sign (LCS) and variable message sign (VMS), an over-height detection system (OHD) and a new tunnel management system.In the absence of suitable guidelines, various standards were used to carry out the refurbishment. The Austroad Guide to Road Tunnels and AS4825 Tunnel Fire Safety, although designed for new tunnels and not specifically intended for existing tunnels, provided a framework. A multi-criteria assessment of risk (MCAT) was carried out to determine the systems to be provided.The Terrace Tunnel has perhaps set a benchmark for refurbishing existing tunnels as few projects of this type have been completed recently. This paper examines the process and the outcomes.CITATION:McGavin, T J, 2014. The refurbishment of the Terrace and Mt Victoria Tunnels, Wellington, New Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 87–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The stratigraphy of the Singleton Coal Measures is reviewed and a revised stratigrapixy which has been ratified by the N.S.W. Standing Committee for Coalfield geology is nominated and defined by a selected type section. Withir the type section the occurrence of repetitive phases are illustrated and described. Coal. Measure units within the Singleton Coal Mean sures, termed the Wollombi and Wittingham Coal Measures respectively, are correlated with the Newcastle and Tomago Coal Measures. In formal nomenclature the Singleton Coal Measures are designated the Singleton Super Group. The major depositional cycles within the Coal Mea- sures are outlined together with those lesser phases within the Coal bearing sequences that influence the mining conditions likely to be encountered. Both tectonic and sedimentary features of the Singleton Coal Measures are considered and the localized post depositional effects on the coal seams and roof strata in- duced by differential, compactions are emphar Sized.

Jan 1, 1972

By Manca PP, Rossi G, Lipari D, Knissel W, Massacci G, Licheri P, Fioravanti E, Helms W, Lai S

Mining of the massive complex sulphides orebodies of Campo Pisano and San Benedetto (Southern Sardinia, Italy), dates back to before Christ, though their exploitation with modern technology was only resumed in the middle of the last century. The increasingly adverse economic conditions and the weakness of both country rock and mineralization were concurrent in forcing the Company's management to develop suitable high-productivity stoping methods. In the framework of a project fi- nanced in part by the Commission of the European Coranunities, and carried out in cooperation with the Universities of Cagliari (Italy) and Clausthal (Germany), a cemented backfill stoping method was developed. The concrete mix preparation and placement facil- ities, study of the cement mixes and endeavaa-s to optimize the methods are described. The monitoring system for measuring stress evolution within the emplaced backfill is illustrated together with the successful replacement of part of the Portland cement

Jan 1, 1992

Ventilation characteristics of a three h -nc longwall development panel in a 1/100th tale hydraulic model using dispersion mechanics are the first applications of its Find in ventilation. Dispersion mechanics gives additional and important ventilation parameters such as degree of mixing, bypassing, -ecirculation etc. These are not obtainable the traditional pressure-volume methods. Experimentally, the model work investigates entilation characteristics of different stopping layouts, including leaky stopping,, cut-throughs and return roadway, brattice tyre ventilation and the effects of flow rate reduction on air distribution in the headings. Additionally, a model of methane generation at the face provides results used to calculate the dispersion characteristics in the return airways. It is concluded that the model resui,s -trongly suggest that dispersion mechanics could be applied to mine ventilation surveys to provide quantitative flow pattern data and details of effective dispersion '?_C!,r riro ò `b' eritilat.ing air.

Jan 1, 1983

By J Beniscelli

Some words to honour Pedro:Pedro was among the few persons with a very high level in geology modelling, resource and reserve estimation, geometallurgy development, sampling theory applications and a deep understanding of the mining industry needs. He had brilliant ideas about new developments on economic geology. He was always looking at the long-term and proposed challenging questions a decade in advance on their solution.The fundamental aim of geometallurgy is to add economic value to the mining of mine resources by timely providing information and knowledge about the relevant metallurgical variables represented by their space models. In this manner, geometallurgy allows obtaining the optimal design of a project, mitigating processing risks, optimising and supporting production plans and identifying and assessing mining business opportunities.This paper describes the conceptual framework and geometallurgical definitions and some of Codelco’s experience during the last 15 years.

Sep 5, 2011

Managers are demanding efficient use of their resources and part of this demand is leading to the idea of integrated audits for Occupational Health and Safety (OH&S), quality and the environment. It is possible to construct audits which test the compliance in this area with standards established by management systems and it may be that such an integrated audit of a site could reduce the time of auditing and be equally effective as three separate audits. However, this is only a maybe. To do an audit on all three aspects when they are not fully integrated results in more time wastage than doing three separate audits. But organisations are not structured around the audit process (some financial managers may query this statement). The organisational management systems are put in place to achieve the organisational goals - presumably in an efficient and cost-effective manner.

Jan 1, 1995

The goal of the Bureau of Mines, U. S. De- partment of the Interior, diesel engine research program is to reduce exhaust emissions and mini- mize the risk of fires and explosions caused by the use of diesel-powered equipment in under- ground mines. Significant results of research conducted during the last 5 years are briefly described, with references to published reports on specific topics. Topics covered here include brief discussions of a newly completed diesel research laboratory, the effects of a fuel addi- tive on diesel exhaust particulate matter, the effect of diesel engine maintenance on emis- sions, a diesel particulate filter for equipment used in underground metal and nonmetal, and coal mines, and lastly, the prototype hydrogen- powered mine vehicle. These research accomplishments could favor- ably affect the mining industry by reducing the health and safety hazards associated with the use of diesel-powered equipment in underground Mines.

Jan 1, 1988

According to the temporal and spatial distribution of regional metallogenesis, the Pacific Rim can be divided into four global metallogenetic systems. The Asia-Australia W-Sn metallogenetic belt is the typical representative of intracontinen- tal metallogenetic systems. This belt resulted from Mesozoic and partly pre-Mesozoic tectonic magmatism, mainly re- lated to S-type granite of crustal source, that was generated by collisional orogeny combined with oceanic subduction in intracontinental and continental margin settings. Based on the concept of metallogenetic series, there is a group of min- eralised ore types showing a definite spatial and temporal distribution from endogenetic to exogenetic. These metalloge- netic series are widely distributed in the Asia-Australia W-Sn metallogenetic belt, and are well developed in Southeast China. Five metallogenetic series and two petro-minerogenesis evolution models have been established according to their tectonic settings, various types of granitoids and metallogenetic evolution.

Jan 1, 1995

An international raw material partnership, a $164 million 900,000 long ton per year aluxAna plant; an ideal location at Gladstone, Queensland, Australia - this is Queensland Alumina Limited, on stream in 1967 expanded 50 per cent by the end of 1968. Queensland Alumina Limited is the world¦s most modern alumina refining operation which is owned by an international consortium of four companies; Kaiser Aluminum & Chemical Corporation of the United States with 52 per cent; Alcan Aluminium of Canada with 20 per cent; Pechiney of France with 20 per cent; Conzinc Rio Tinto of Australia, 8 per cent. Q.A.L. operates as a co-operative -- the partners do not draw profits from the venture. Instead, each member of the consortium draws alumina in proportion to his share of the ownership. The method of disposal of this alumina is for the partner to decide.

Jan 1, 1969

George Fisher Mine, near Mount Isa in northwest Queensland, has been producing Pb-Zn-Ag ore since the late 1980s. It consists of two separate underground deposits, George Fisher South and George Fisher North. These two deposits are drilled and modelled separately but are crushed and hoisted as a single stream. The Pb-Zn concentrator in Mount Isa processes ore from George Fisher Mine and Black Star Open Cut, with production also from the Isa Lead Mine until January 2006. This paper outlines the steps involved in setting up a robust reconciliation system for George Fisher Mine, in conjunction with requirements of the Pb-Zn concentrator, Black Star Open Cut Mine and the Mount Isa Lead Mine. Good quality input data and commitment to training have contributed to establishing a robust and effective reconciliation system. Reconciliation data has highlighted several other continuous improvement opportunities.

Jan 1, 2006

By Tapp BA

Australia, considered an energy and mineral resource rich country, is poised on the verge of a major mineral industry 'boom'. It has been repeatedly emphasised that this growth in the mineral industry will form the basis of future economic development. Currently the mining and mineral processing industries use some 32% of the annual primary energy consumption in Australia. This share, although large even now, will increase with the realisation of the 1980's production expansions to 40% by 1985. Two metal industries dominate the energy scenario; iron and steel and aluminium. Major expansions in the local industry will be dominated by the aluminium industry. This highly energy intensive industry has planned major increases in metal production throughout the eighties. The implications of exporting cheap energy to pay for expensive oil imports, the ramifications on Australia's infrastructural ability to supply these major energy needs and the other options that might be

Jan 1, 1981

The commercial outcomes from new mining projects or brownfields expansions often fall short of feasibility study forecasts because of technical under-performance. This paper: reviews past feasibility study performance; identifies the key drivers of underperformance; and proposes actions that can be taken to manage the risk of underperformance. There have been a number of published reviews of feasibility study performance since the 1970s. The results of these studies are summarised together with recent unpublished data. Key drivers of underperformance include inadequate metallurgical testing, simultaneously pushing a number of project parameters beyond comfortable limits and a failure to recognise the linkage between mining rate and head grade. Actions can be taken during the data acquisition phase and during the feasibility study to manage project technical risks. These generally require a more flexible approach to study management than can be achieved under a ælump sumÆ contract.

Jan 1, 2003

A typical large surface mine in Scandinavia has hard rock, a cold cli- mate, poor ore, a complicated vein type orebody and high labour costs. In order to survive, these mines have to maximise their ore production, minimise waste extraction and get the most out of every man hour. This article describes two examples of how inclined blastholes drilled with hydraulic percussive drills can help to meet these requirements. Both of these Scandinavian mines, Kemira Ltd's Siilinjarvi mine in Finland and Sydvaranger A/S's Bjornevattn iron mine in Norway, use inclined blastholes of 200 mm in diameter. The Siilinjarvi quarry is using inclined holes in production drilling. The Bjornevattn iron mine is blasting the final pit walls with inclined holes. The benefits gained when using inclined instead of vertical blastholes are better selectivity, better bench drilling conditions, steeper final pit walls and increased safety.

Jan 1, 1989