Search Documents

By T J. Grandfield

Paste fill has been used successfully at Henty Gold Mine for the past five years. It has allowed 100 per cent extraction of the orebody, stabilised poor ground and enabled wide sections and offsets to be mined safely. However, there are a number of inefficiencies in the current paste fill system. These include the low output from the drum filter, the addition of aggregate to the paste to compensate and the trucking of paste from the plant to the portal. These inefficiencies have increased the operating cost of the paste fill system and caused a number of operational challenges such as blockages and increased pipe wear. These challenges have been partly overcome by taking ownership of the paste fill process, improved quality control and better communication. Henty is currently developing two new orebodies, the Mt Julia and the Darwin and has an opportunity to build an efficient paste fill operation. This is likely to be a high density paste system without aggregate, either located above the new orebodies or located at the plant and pumped to the new site.

Jan 1, 2002

By K S. Park, J K. Kim, J H. Park, Y Su

The present study investigates the possibility of the direct removal of oxygen from the Ti-30Ni (wt per cent) alloy melt through the thermodynamic equilibrium reactions at 1623 K in the vertical tube furnace. The deoxidation efficiency of Ti-Ni alloy melt by adding different contents of metallic calcium (Ca) as a deoxidant was evaluated with the binary CaF2-MgCl2 flux. The thermodynamic equilibrium experiments showed that the total oxygen content in the alloy decreased from about 650 ppm to 350 ppm when 3.5 wt per cent Ca was added to the Ti-30Ni (wt per cent) alloy. Alternatively, the effect of flux composition in the CaF2-MgCl2 flux on the oxygen content was also investigated at 1623 K. Therefore, the effect of binary flux systems on the deoxidation ability was compared at 1623 K. According to the results, the flux system with 80 per centCaF2– 20 per centMgCl2 exhibited the best deoxidation capability, ie total oxygen content in the alloy reduced from 1450 to 550 ppm.

Aug 21, 2024

By C A. Foss, K Leslie, C Arnold

Magnetic susceptibility measurements provide rapid, non-destructive testing of drill core, but cannot directly map magnetite and/or hematite content. Combined magnetic susceptibility and magnetisation measurements provide much more diagnostic information and, with sparse calibration constraints, are able to quantify magnetite and hematite concentrations and potentially map differences in grain size and texture. We have developed a travelling three-component vector magnetometer that can be run alongside core to map its external magnetic field. The logger has been designed to operate in core sheds and at remote drill sites. It is used to rapidly scan a length of core, with each core being scanned in different rotations. The magnetic field contributions from any remanent magnetisation rotates with the core and cause differences between successive measurements, while the field contributions from any induced magnetisations with isotropic magnetic susceptibility remain constant. Deconvolution of the magnetic field data with simultaneous three-channel inversions of the multirotation data separates remanent and induced components. Interpretation of this data provides estimates of the intensities of induced and remanent magnetisations, the orientation of the remanent magnetisations and the ratios of the induced and remanent magnetisation strengths. We expect these magnetisation parameters to correlate with stratigraphy through a banded-iron formation. Furthermore, we anticipate that we will be able to use this information to map zones of oxidation and other changes along the core. This novel instrument is one component of an integrated CSIRO program to provide new capabilities for iron ore exploration and development based on studies of magnetic fields and magnetisations at scales ranging from centimetres for these core investigations to tens of kilometres for formation studies.CITATION:Foss, C A, Leslie, K and Arnold, C, 2015. Rapid logging of different magnetic phases in banded ironstones using a travelling three-component vector magnetometer, in Proceedings Iron Ore 2015, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Millen M. J, Rainey S, Sowerby B. D

The control of size reduction in grinding machines and circuits may be enhanced by a continuous and accurate measurement of the particle size of solids in appropriate process streams. This paper presents a brief review of commercial particle s

Jan 1, 1997

The mining industry is facing tremendous economic challenges. Fluctuating and depressed commodity prices, the ever-increasing pressure from environmental legislation and the competing global opportunities for capital investment are placing enormous strains on every aspect of the mining business. At the same time, mines are generally becoming older and deeper with all the logistical and rock mechanics difficulties that this entails. In the face of these new challenges the industry looks to technological advances to make operations more efficient and profitable. One approach is to develop and implement highly automated and computerised equipment as part of a trend towards major reductions in the underground workforce. This approach requires more capital investment rather than less and requires a more sophisticated and well-educated workforce with skills which are generally in high demand in society as a whole. It is difficult to see how the benefit that can be gained from such technology can justify the expenditures necessary to make it operate reliably underground on a daily basis. Nor is it easy to foresee how the mining industry, based as it is often in very remote areas, will be able to hire and retain sufficient numbers of people to maintain such fleets of equipment. Another approach, and the one which I favour, is the implementation of much greater control over the whole of the mining process. Mining is essentially a very simple process - we break rock and move it. The most cost-effective means of moving and processing the mining product depends entirely on the way it is broken - it depends on primary fragmentation by blasting. I propose that the way forward for the industry in the face of our present difficulties, is not new technology but is to utilise the level of technology which currently exists in ways which have traditionally been regarded as too difficult or too inflexible - improved fragmentation and the use of conveyors. The technical success of this approach depends on the complete re-design of the ore handling system from the face or stope drawpoint to surface. The fundamental issue which determines the success of this approach is designed fragmentation.

Jan 1, 1995

By R Cox, S Pandey

The coal seam gas (CSG) industry is expanding rapidly in the Surat and Bowen basins. CSG production involves pumping water from the coal seams to release the gas adsorbed to coal particles. The reduction in water pressure in the coal seams will cause some reductions in water pressure in overlying and underlying aquifers because there will always be some interconnectivity between the formations. The Surat Basin is a sub-basin of the Great Artesian Basin, which contains aquifers of high economic, environmental and cultural value. The Condamine Alluvium is also an important water resource, which overlies parts of the eastern margin of the Surat Basin.Under the Queensland (Qld) regulatory framework, an area of intensive CSG development involving multiple CSG operators can be declared to be a cumulative management area. For such areas the Office of Groundwater Impact Assessment develops assessments of future impacts on aquifer water pressures and develops and manages arrangements. The results are published in underground water impact reports.The Surat underground water impact report (QWC, 2012) was approved in December 2012. This paper summarises the place of the report in the Queensland regulatory framework, the content of the report and progress in its implementation.CITATION:Cox, R and Pandey, S, 2013. Managing groundwater impacts in the Surat Basin, in Proceedings Water in Mining 2013 , pp 169-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

The Porgera gold project is now in its seventh year of operation as one of the world's prime gold mining projects in one of the most underdeveloped and remote regions of the world. The unique gold deposit was development in stages to its present size of operation with an underground mine of 2000tpd, an open pit operation moving 210,000tpd and a complex metallurgical plant treating an average of 16,500tpd of ore. During the past years the operation had to address an array of issues relating to the "development" of the region and this is still ongoing. Development means different things to different people and though the parties that signed the different agreements relating to the Mining Development Contract were aware of this, none has real- ised the extent to which this is true. The developing company (a joint venture between Placer Pacific as the Manager, Goldfields Porgera, Highlands Gold and the Government of PNG), provided funds for risky exploration and the capital for development of the project. Its shareholders ex- pect an economic and viable mine operation from the deposit to ensure them returns on their investment. The local people gave up their land, their isolated way of living and accepted to be out of their comfort zone for some time in anticipation of a better lifestyle and economic benefits in support of that lifestyle. The PNG Government has a leg in both camps and expects both outcomes at the same time. The Government is also the regulator and expects compliance on top of that. If development in general is to be successful, all parties must substantially satisfy all expectations. It is evident that the outcome of some elements of development are reasonably defined (i.e. develop a viable mine to exploit the deposit), whilst other elements are moving targets (i.e. a better lifestyle). The seeds for conflict are thus abundantly present and to resolve them requires the will of all parties in all areas to come to a solution. This path to problem solving is many times torturous as each party comes from a different culture and background and has a different understanding of the parameters in the equation.

Jan 1, 1997

By R Wei, Y Peng

With the depletion of high-quality ores, the efficiency of extracting difficult gold ores through flotation and leaching becomes very important in the mining industry. Iron contaminants, sulfide and carbonaceous coatings on the surface of gold and gold bearing minerals significantly hinder the recovery of gold during gold processing. As the surface of gold minerals is easily contaminated, coatings of iron oxides and iron hydroxides originated from the grinding process and oxidation of iron sulfides will cause a retarding effect on both gold flotation and leaching.To mitigate the processing issues caused by undesirable surface coatings on gold minerals, a new technology in treating surface coatings of iron contaminants has been developed. The pulp potential and pH of the slurry are altered to allow dissolution of surface coatings which are further excluded by the use of complexing reagents. The current work shows that iron contaminants can be removed from the surfaces of gold through Eh-pH adjustment and chelation which result in significantly improved gold flotation response. The addition of complexants aids the formation of iron chelates to prevent the iron species in the solution from forming iron oxide and iron hydroxide in the flotation conditions.CITATION:Wei, R and Peng, Y, 2014. Mitigating the effect of surface coatings on gold processing, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 187–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By N Collins, A Woodley, A N. Danoucaras, C McCombe, N C. Kunz

Over the past decade, the mining industry has come to recognise the importance of water both to itself and to others. Water accounting is a formalisation of this importance that quantifies and communicates how water is used by individual sites and the industry as a whole. While there are a number of different accounting frameworks that could be used within the industry, the Minerals Council of AustraliaÆs (MCA) water accounting framework (WAF) is an industry-led approach that provides a consistent representation of mine site water interactions regardless of their operational, social or environmental context that allows for valid comparisons between sites and companies.The WAF contains definitions of off-site water sources and destinations and on-site water use, a methodology for applying the definitions, and a set of metrics to measure site performance. The WAF is comprised of two models: the input-output model, which represents the interactions between sites and their surrounding community, and the operational model, which represents on-site water interactions.Members of the MCA have recently adopted the WAFÆs input-output model to report on their external water interactions in their Australian operations, with some adopting it on a global basis. To support this adoption, there is a need for companies to better understand how to implement the WAF in their own operations. Developing a water account is non-trivial, particularly for sites unfamiliar with the WAF or for sites with the need to represent unusual features. This work describes how to build a water account for a given site using the input-output model, with an emphasis on how to represent challenging situations.CITATION:Woodley, A, Danoucaras, A N, McCombe, C, Kunz, N C and Collins, N, 2013. A robust methodological approach for mine site water accounting, in Proceedings Water in Mining 2013 , pp 335-342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D Asahina, T Endo, H Hosono, T Takemura

Changes in the stress field around faults due to the excavation of underground space or the extraction of underground resources induce fault reactivation. To understand the mechanism of fault reactivation, it is important to observe the deformation and sliding processes of the asperities, which is regionally contacted areas at the fault planes. In the laboratory, triaxial compression tests are commonly conducted to reproduce the stress conditions around faults and study their mechanical behaviours. The conventional measurement devices for triaxial compression testing (eg load cells, local deformation transducers, and piezoelectric sensors) uses sensors to measure changes in the physical properties of rocks, but the direct visual information for the sample condition inside the pressure vessel is limited and can only be estimated from the sample after the experiment. We recently developed a direct visual measurement system to observe the slip behaviour of rocks from the inside of the pressure vessel of a triaxial test apparatus. This paper introduces this visual measurement system and presents some preliminary experimental results. The visual measurement system consists of a steel housing with a built-in commercially available digital camera. The triaxial compression tests were conducted to visually observe the sliding behaviour of the pre-cut specimens and to measure its behaviour through the digital image correlation (DIC) method. The captured images and the DIC results show the displacement field of the specimens for different confining pressure. We verified the sliding behaviour and the failure at/around the triangular asperity under at different confining pressure.

Nov 29, 2022

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

By M I. Pownceby, W J. Bruckard

A South African chromite sample was subjected to characterisation and physical beneficiation testwork in order to assess its suitability to produce an upgraded chromite product with a silica level of <1 per cent SiO2 and a chromite level of >46 per cent Cr2O3. Chemical analysis by XRF indicated that the bulk material had a Cr2O3 content of 40.5 per cent w/w and a SiO2 content of 7.5 per cent w/w. Combined XRF analysis with sizing data showed that the majority (~70 per cent) of the siliceous material was present in the +600 ¦m fraction while ~70 per cent of the Cr2O3 was in the -600 ¦m fraction. Qualitative mineral phase analysis by XRD indicated that the sample mineralogy was dominated by ferrian-magnesiochromite spinel ([Fe,Mg]Cr2O4) and aluminium-chromite spinel (Fe[Al,Cr]2O4), with enstatite (Mg2Si2O6), haematite (Fe2O3) and anorthite (CaAl2Si2O8) as minor phases. SEM and EMP characterisation showed that the silica was mainly present in discrete enstatite grains but lesser amounts were also present as the high silica phases plagioclase and enstatite on the edge of grains. Wet gravity separation performed on sized fractions (-600+106 ¦m size range) from the -2.0 mm (primary) ore as well as the ore that had been crushed to pass 0.6 mm (secondary) showed that stage crushing of the -2 mm +600 ¦m fraction followed by wet gravity separation upgraded the Cr2O3 grade at 70 per cent Cr2O3 recovery from ~44 per cent Cr2O3 in the primary material to 46 per cent Cr2O3 (the target grade specification) in the secondary sample. It also showed that the stage crushing of this +600 ¦m fraction at a cut-off level of one per cent SiO2 increased the cumulative Cr2O3 recovery from ~50 per cent in the primary material to ~63 per cent in the secondary sample in the same size range of -600+106 ¦m. The extent to which additional crushing could lead to improved chromite recoveries at the required chromite and silica grade target specifications was not determined. This experience demonstrates that prior to processing test work being conducted, a thorough understanding of the chemistry and mineralogy of the test sample promotes efficient and targeted processing research.

Jan 1, 2008

By I Gray

Other than being reasonably certain of the average vertical stress being lithostatic, there can be little certainty about stress in the ground. The stresses and strains in rock are a function of gravitational effects, external load, thermal changes, diagenesis and their mechanical properties including elastic, creep and post failure behaviours. It is highly desirable to measure stress where mining is going to take place, even if the virgin stress condition has already been changed by mining. The concept of some far field stress value that is more or less constant is usually invalid and can be dangerous to use in mine design. Measuring stress is not simple. The basic processes are broken into two categories, one where the rock will not fail around the borehole in which the stress is being measured and one where the rock has failed or will fail. Because of the complexity and cost in obtaining a single, precise stress measurement it is highly desirable to have some system to be able to obtain an idea of the uniformity, or otherwise of the stress situation between precise measurements. Table 1 shows the methods for measuring stress. The first five methods work on the basis of some fairly direct measurement of mechanical rock behaviour while the last three are attempts to get some idea of stress out of core long after it is removed from the host rock. While these latter methods appear to tick all the boxes for applicability there is a great deal of uncertainty in the results that they deliver. This paper reviews the methods for measuring stress and presents two new methods. These are a three dimensional overcore system to provide precise stress measurements in rocks that will not fail around the borehole and a core ovality system. The latter can be used to provide information on the stress difference orthogonal to the core. It is particularly useful because it can be used every metre of core length.

Nov 29, 2022

By T Baumgartl, T Huynh, K Tungpalan, E Wightman, M Edraki, M Tayebi-Khorami, L Huang, S Palaniandy, E Manlapig

With the increasing rate of tailing production worldwide there is a growing concern about the hazards of tailings storage facilities (TSF). Past and current mining, processing and waste disposal strategies that focus on the extraction of the valuable minerals, and an economic assessment only, are no longer suitable. Social implications and environmental legacies must be included for effective evaluation. This is possible by using an integrated assessment framework to evaluate more alternatives, including the production of additional saleable and benign streams, alternative tailings treatment and disposal as well as options for reuse, recycling and preprocessing of existing tailings. Tailings are not viewed as a final waste product but as part of the resource. From the sustainability perspective the models developed in integrated research programs will contribute to more effective methods for assessing different scenarios and potential processes and lead to better environmental management, increased production of benign tailings and improved efficiency of water and energy use and thus more responsible resource stewardship of the ore resource.This paper presents preliminary results from a multiyear research program on integrated tailings management at the Sustainable Minerals Institute (SMI), The University of Queensland, called ‘Designer Tailings’. The project involves the gathering of experimental and observational information on tailings biogeochemical processes to design and modify the range of activities within mineral processing plants, upstream characterisation ore and gangue, and downstream tailings management for desired tailings properties and outcomes. This information will assist the development of new total integrated value chain CITATION:Edraki, M, Huynh, T, Baumgartl, T, Huang, L, Andrusiewicz, M, Tungpalan, K, Tayebi-Khorami, M, Wightman, E, Palaniandy, S, Manlapig, E, Evans, C, Farrokhpay, S, Bradshaw, D and Vink, S, 2014. Designer tailings – an integrated model for tailings management, in Proceedings Life-of-Mine 2014 , pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By G King, Q Shu, W Cao, F Gyakwaa, H Singh, S Wang, M Huttula, T Fabritius

Metallurgical slag, such as refining slag, is essential to enhance or promote steel cleanliness. The CaO–MgO–Al2O3–SiO2 system is the primary source of oxides-based inclusions. It plays a vital role in applications in various pyrometallurgical processes. Numerous thermodynamic databases and physicochemical properties of slag studies mainly focus on quenched samples and measurements at room temperature. Consequently, the present study explored the physicochemical, structural properties and crystallisation evolution for CaO–MgO–Al2O3–SiO2 glassy slags via in situ hightemperature Raman spectroscopy and synchrotron X-ray diffraction. The study was carried out by synthesising CaO–MgO–Al2O3–SiO2 slag with varying Al2O3/SiO2 ratios. The results from the in situ high-temperature measurement demonstrated a pattern showing a transformation of a broad peak from the glassy matrix to crystalline peaks. The study showed crystallisation of dominant phases such as Ca2SiO4, Ca2Al2SiO7 and CaAl2O4 that correspond and are attributable to changes of structural units during in situ high-temperature measurements. The results further showed a correlation between an increase and transformation in crystalline phases observed from the spectra obtained from non-isothermal heating of the samples.

Jun 19, 2024

By S Wainio, P J. Beckett, T Miller

Lichens are a symbiosis of fungi and algae. Air borne elements and gases are absorbed very efficiently over the entire surface of the lichen, because they have no protective structures such as a waxy cuticle or stomata. A survey in 1977 (one year before the Sudbury Regreening program began), indicated that several Cladonia spp had invaded the soil in Sudbury’s open birch woodlands. Pollution sensitive species such as Cladonia rangiferina and C. mitis occurred 20–25 km from the smelters. It was anticipated that the improvements in air quality and reclamation efforts would allow a natural invasion of pollution sensitive species into what once was a lichen desert that surrounded the smelters. The purpose of this project was to study the invasion of terricolous (soil-inhabiting) communities of lichens and mosses on reclaimed land in the Sudbury region 45 years after commencement of the Sudbury Regreening Program.

Aug 2, 2023

By D Zielinski-Nicolson

The emergence of affordable, portable and versatile wireless devices has enabled a new frontier in mine safety equipment. Existing solutions provide methods for tracking personnel and assets in underground mines but are not designed to optimally integrate into existing and emerging systems. Mine management are often required to coordinate primarily independent emergency, personal protective equipment (PPE), tracking and collision avoidance systems from multiple vendors. These systems involve a variety of wireless technologies that require separate integration projects that discourage adopting new services and policies.

May 5, 2022

By N J. Grigg

Gekko Systems has developed an underground pre-concentration plant (Python) to reduce mine operating costs. Many ores liberate favourably using either high pressure grinding rolls (HPGR) or vertical shaft impactors (VSI). Using these comminution circuits for mineral liberation; rather than for the final recovery process and by utilising a high mass pull, high recovery process route (gravity/flotation), a narrow, low head, compact processing plant was developed that can sensibly be operated underground. The Python underground processing plant can provide a number of advantages for narrow vein mines including lower haulage costs, improved mine call factor and lower operating costs. The focus on fine crushing reduces the power requirement of the plant to approximately 8 kWh/tonne. The Python underground processing plant has been designed to be towed down the decline or lowered down a shaft, and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a saving in mining costs and a significantly smaller environmental footprint.

Jan 1, 2008

By J Franke, C Gonzalez

One of the regular tasks of geotechnical and mining engineers is the measurement and management of deformation in underground excavations. Although several methods are used to do so, the incumbent methodologies for monitoring deformation and ground support serviceability are limited to the use of visual observations or measurements at discrete points, resulting in a qualitative assessment only. The introduction of LiDAR technology allows a quantitative assessment across the entire excavation volume and its rock surface, by collecting a full three-dimensional image of the entirety of an excavation such as an underground drive, decline, or a tunnel. Comparisons between epochs of complete 3D data coverage allows for change detection over time that doesn’t feature otherwise typical omissions. The implementation of regular scanning has shown to be highly advantageous for mines with swelling or squeezing ground, but also at mines with rapid deformation. Despite the LiDAR potential, its adoption has been slow. A key reason for that is that working with point clouds is foreign to most geotechnical engineers. Point clouds have long been the realm of surveyors, but to fully adopt their use in geomechanics requires retraining, upskilling, and devotion by the individuals and the company. Sites are already stretched, so often there are insufficient resources to be applied to bringing the new technology into use. The solution to this hurdle is to partner with subject matter experts to achieve the desired high-quality outcomes without the commitment of time by geotechnical personnel. This paper presents a new solution of fully automated raw LiDAR point cloud data processing that not only enables geotechnical engineers to avoid having to learn unrelated skills by allowing for deformation monitoring without associated training or expertise, but it also provides instant reporting results as well as a sophisticated database with features otherwise not available. All data processing time and effort is completely replaced by an automated process which at the same time opens up the opportunity to monitor many more excavation volumes at a higher frequency than is possible with conventional tools and methodology.

Nov 29, 2022

The investigations described in this paper aim at the development of a new impact mill. The objective is to produce particle size distributions below 10 .tm without using an air classifier. Circumferential rotor speeds of up to 200 m/s are strived for.

Jan 1, 1993