Search Documents

Sample preparation for gold samples, where the distribution and size of gold particles is often irregular, usually demands that a relatively large sample weight is taken to produce a representative sample for analysis. Traditional sample preparation of gold samples incorporated multiple stages of coarse particle size reduction followed by subdivision of the sample prior to final fine pulverising. This technique developed because of the limited equipment options available to laboratories. As a result significant errors are introduced and the final sample size being pulverised is a small fraction of the original sample weight. Three significant developments have occurred in the last 25 years to significantly improve sample preparation of gold samples: 1.  large capacity fine pulverising,2.  fine jaw crushing, and3.  whole sample coarse pulverising. In the mid-1980s an Australian manufacturer developed large capacity pulverising bowls which had the ability to reduce samples with a mass of 1.5 - 3.5 kg to a nominal 0.075 mm product in approximately three to five minutes. Laboratories were able to produce a large homogeneous pulverised sample which significantly reduced the error in sampling. However, exploration and mine samples are usually 7 to 10 kg and the sample requires a subdivision stage following crushing to produce the 3.5 kg for the pulverising step, thus introducing potential for significant error. The development of fine jaw crushing allowed particle size reduction to -2 mm which reduced the subdivision error of the bulk sample prior to fine pulverising. Subdivision of the crushed sample at -2 mm still results in potential sampling errors, where the gold particles are not sufficiently liberated to be representatively sampled. Clearly the best option would be to reduce the particle size small enough to ensure a representative sample prior to final pulverising. Continuous mills offer a partial solution but are relatively slow and subject the sample to differential pulverising prior to subdivision. Clearly this does not provide the best solution for routine laboratory applications where high volumes of samples are to be processed. The recent development of a large capacity coarse pulverising system allows samples of up to 10 kg to be reduced to -0.25 mm prior to subdivision, and fine pulverised to -0.075 mm. Laboratories now have the necessary equipment to perform reliable large capacity sample preparation of gold samples. The exact choice of a sample preparation scheme may still depend on particular ore types but the need for multiple crushing and subdivision stages is redundant.

Jan 1, 2008

By M Wortley, J Korteniemi, D La Rosa, L Rajavuori

Geometallurgical modelling of an orebody provides benefits to a mine by gaining a better understanding of the ore characteristics and how they affect the performance of the concentrator. With this knowledge, plant operating conditions can be adjusted to optimise throughput and recovery in advance of the arrival of particular ore types. Therefore, it is extremely important that the origin of the ore being processed is known as accurately as possible. Depending on the homogeneity of the ore characteristics, reliance on assumptions about stockpile residence times, scheduling and material handling can render the best geometallurgical models useless.The solution adopted at Agnico Eagle’s Kittilä mine was to utilise Metso SmartTags™ and in-house expertise to develop a system that continuously and accurately links geotechnical and lab data from the mine to the performance of the plant. This application presented several unique opportunities and challenges. For example, this was the first installation of a SmartTag™ system for geometallurgical modelling in an underground mine. Challenges included the fact that the system installation is routinely subjected to temperatures below -20°C.The system was installed and commissioned in early 2013 and has been operating continuously since. Kittilä has begun to see the benefits of the system, with an increased understanding of how different ores are processed in the concentrator. Other advantages include the ability to alert operators about the arrival of difficult ores and a better understanding of the ore handling systems.This paper describes the installation and use of the system at Kittilä and details some of the geometallurgical relationships that have been developed using the data collected so far.CITATION:La Rosa, D, Rajavuori, L, Korteniemi, J and Wortley, M, 2014. Geometallurgical modelling and ore tracking at Kittilä Mine, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Waihi Gold Mining Company Limited, a wholly owned subsidiary of Normandy Mining Limited, operates the Martha gold mine, located in the township of Waihi, New Zealand. The operation, an unincorporated joint venture, comprises Normandy Mining Limited (67.070/0) and Otter Gold Mines (32.94%). Since gold was first discovered at Waihi in 1878, it has formed a key part of the region's economy. In 1909 the Waihi mine was described in a report to Parliament as æthe most important gold mine in Australasia and one of the greatest in the world.Æ That was a record year for production, with 416,813 tons of ore mined and some 1,120 men employed. Today the mine produces up to 1,250,000 tonnes of ore annually, and the project employs some 234 men and women. In 1999 the value of the gold and silver produced ($59 million) made up 47% of Waihi's estimated GDP. Waihi Gold has made significant contributions to the Waihi economy, community and the Hauraki region as a whole. Since the mine was re-opened in 1987, thousands of local people have benefited from the mine. In 1999, consents were granted allowing an extension to the mine life (the Extended Project) and this will result in a further seven years of economic benefits resulting from mining activity. The Company has undertaken extensive consultation throughout project planning, construction, operations and rehabilitation. Ongoing liaison and involvement with all community sectors, including Tangata Whenua and Iwi, local residents, recreational groups and schools remains an integral part of the operation. Throughout the life of the modern Martha Mine, the Company has actively supported the local community in the form of donations, sponsorships, the provision of amenities, and by participating in community events. A well established environmental team exists at the site. Environmental and community performance is measured by an independent five-assessment process, and the Company is committed to achieving excellence through ongoing improvement programmes and staff awareness. When the mine is closed, the open pit area will be transformed into a recreational lake, and the tailings storage facilities will be rehabilitated to become a combination of wetlands, grassed areas and ponds. Resources will be provided by the Mine to ensure the rehabilitated site remains in a safe and self-sustaining, stable condition in perpetuity. The mine is regarded as a showcase on a world standard of how a modem mining operation can successfully coexist with the nearby community.

Jan 1, 2000

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M Spagnolo, M Ashley, D, L Reemeyer

PasmincoÆs Century Concentrator in North West Queensland commenced operations in November 1999. The nameplate production capacity of 500 000 tpa of zinc metal production in concentrate was achieved in August 2002. Completion of the production ramp up was successful due to the culmination of a number of initiatives throughout 2001 and 2002. Mine to mill interaction to understand and eliminate head grade related bottlenecks affecting Concentrator production and reduce feed variation. Grinding circuit process development û operating and process control strategies to improve stability and reduce grind size to support zinc recovery. Pumping upgrades to control spillage in ultrafine zinc flotation Low density zinc flotation strategy û to improve silica-sphalerite separation to improve zinc recovery while maintaining acceptable silica in final concentrate. Flotation circuit process development û froth crowders, froth cameras and reagent control strategies to improve primary zinc flotation performance. Review and implementation of longer campaigns between planned shutdowns to improve availability. Team reorganisation û to improve setting and implementation of metallurgical strategies. This paper describes these initiatives and their contribution in achieving the production target. It also notes the ball mill motor failures that delayed the successful achievement of the ramp up, and CenturyÆs response to minimise the production impact. The paper also outlines the capital improvement program that was implemented to improve zinc recovery to design 82.5 per cent recovery once the production rate had been achieved.

Jan 1, 2003

I The South Platform of the Gippsland Basin is an extensive area of shallow basement covered by a relatively-thin Late Mesozoic-Cainozoic section. Although the sporadic exploration to-date has not resulted in any hydrocarbon discoveries, the area is under-explored and its taste potential has not yet been fully evaluated. The best potential appears to be in areas underlain by the Golden Beach Megasequence where structures are mainly related to basement fault blocks.

Jan 1, 1992

As defined by both the Australian and New South Wales Governments the Illawarra consists of the Tablelands, the Local Government areas of WingecarribPe Shire, Bowral Municipality and Mittagong Shire, the Wollongong sub-region consisting of Wollongong City Council, Shellharbour Municipality and Kiama Municipality and finally the Shoalhaven Shire. I intend here to concentrate on community development in the Wollongong sub-region.

Jan 1, 1976

By Grobler H. P, Chitombo G. R

Production blasting of Dc Beers Consolidated Mines Limited, Koffiefontein and Finsch Mines involves both uphole trough rings of 9 to I I holes and near vertical 360 degree compound rings of 42-54 holes. The rate of production from these stages is dependent upon being able to achieve a specified fragmentation size range and this has driven the derivation of blasting practices to consistently achieve this target fragmentation. At the Dutoitspan Mine, in Kimberley, where mining of the kimberlite pipe is by block caving, 100 per cent extraction of the undercut level by ring blasting is essential. If this is not achieved, pillars are formed which not only inhibit the efficient initiation of the caving process, but also concentrates load onto the extraction level, causing damage to draw points and pillars. These two case studies demonstrate the importance of achieving optimum blasting performance for downstream mining efficiency; ie fragmentation for increased productivity at Koffiefontein Mine and 100 per cent undercut extraction for efficient initiation of the caving process at the Dutoitspan Mine. The case studies also serve to highlight the long road towards blast optimisation taken by De Beers Consolidated Mines Ltd (Koffiefontein. Finsch, Premier and Kimberley Mines) since 1989.

Jan 1, 1995

Thank you chairman, good afternoon ladies and gentlemen. In my talk this afternoon I intend to cover a brief history, some of the recent experiences and an overview of the McArthur River project.If we consider the themes of this forum, Obstacles and Opportunities, I can confidently say that in attempting to develop the McArthur River deposit Mount Isa Mines Limited (MIM) must have encountered almost every obstacle that can be imagined. However the large size and the high grade of the deposit has ensured an opportunity, from which it is very difficult to walk away from.The McArthur River Here's Your Chance (HYC) Deposit is located in the Northern Territory of Australia. It was discovered by Mount Isa Mines Limited geologists in 1955 and is one of the largest known sedimentary stratiform zinc-lead-silver deposits. The deposit has been the subject of numerous investigations and considerable expenditure culminating in a major feasibility study in 1979. There were a number of factors which prevented development, these being the size of the project, the fine grained mineralization, geographical location, market, social and capital cost. The latter had been estimated in the 1979 study to be $800 million at that time.

Jan 1, 1993

By P A. Jenkins, I W. O Jones

WMC has mined the Perseverance disseminated orebody exclusively by SLC (sublevel cave) methods. Deteriorating ground conditions in the vicinity of an orebody inflection forced a re-evaluation of future mining at Perseverance and a strategy to drop down below the inflection zone and recommence the cave was implemented. This strategy has led to increased production at higher grades, resulting in lower costs and better mill recoveries. This paper describes the evolution of mine planning, development, support and production strategies through the successful process of implementing the ædrop-downÆ and re-establishing the SLC.

Jan 1, 2000

The nation of Fiji is located the South Pacific on the æRim of FireÆ some four hours flying time from the eastern sea board of Australia. It is a tourist destination situated on the main route from Australia to the Americas. Fiji is a developing country that has had a fewsetbacks but the country has able, happy people that are very resilient. Most importantly, the country is a safe destination for tourists and businesspeople as the local people are friendly, have good ethics, and most speak English. Fiji is a very willing nation, hungry for knowledge and advancement. The Fiji geological setting on the æRim of FireÆ, that runs from New Zealand across the Pacific through Fiji and on to Papua NewGuinea, has many large deposits of gold and copper. Fiji is an exciting destination for mineral explorers with discoveries of gold, silver, manganese, bauxite, iron and copper. Gold was first discovered in 1921 and the first two mines opened in 1935; one of which was Emperor Gold Mining Company (EGM) the other being Mt Kasi. EGM mines gold on the margin of the Tavua caldera, some 85 km north of the Nadi international airport. EGM has operated continuously for close to 70 years, producing approximately 6.9 million ounces of gold and has an underground reserve of 847 600 ounces with a total mineral resource of 12 335 600 tonnes at 10 g/t (as given in the Emperor Mines Limited Annual report 2003). The mineralisation in Fiji is very exciting and it is common to discover spectacular intersections and outcrops, which are typical for this type of epithermal narrow vein mineralisation, but be aware that the orebodies are variable and not easy to understand.

Jan 1, 2004

In this paper is given a description of the flotation plant recently erected by Broken Hill South Limited at the South Mine, Broken Hill, N.S.W. It has been built on the site of the old flotation plant, which was described in a previous paper published by the author. The present paper is supplementary to the former paper in that it replaced the following sections thereof, namely, those from end of the second paragraph, page 269, to the end of the first paragraph page 282, and from the end of the second paragraph, page 284, to the end of the third paragraph, page 302.The roll crushing, fine grinding, gravity concentration, filtration, disposal of products and sampling in the new plant are the same as described in the above mentioned paper.The reconstruction of the flotation section, described herein, completes the reconstruction and modernisation of the treatment plant which was begun in 1928. A description of these earlier alterations has already been published in the Proceedings of this Institute.

Jan 1, 1935

By N Patel, S Narendranathan, T Mok, J Lowe

The Hazelwood Mine (HM) commenced operations in the 1950s and was originally operated by the State Electricity Commission of Victoria (SECV) prior to it becoming privatised. ENGIE, the current owners of the Hazelwood Mine ceased operations in 2017 and have since transitioned the site into the rehabilitation and closure phase, which is to encompass a full pit lake as part of the final landform. A key aspect of HM closure is the maintenance of long-term stability of the pit slopes to deliver a final landform which is safe and sustainable, particularly given its proximity to critical public receptors. The Princes Freeway, which is the primary access route to the Latrobe Valley (LV), and the Morwell Township are both located immediately to the north of the HM. With due consideration of the mine void and nearby public receptors, the authors performed slope stability assessments of critical mine

Aug 2, 2023

By P Hayes, D Fadhlurrahman

Molten slags, fluxes and salts play key roles in a wide range of the high temperature industrial process applications, including metals production, refining and recycling, metal manufacturing processes, electrochemical metal production cells, batteries, and efficient heat transfer media. Recognising the importance and significance of fundamental scientific knowledge of these systems, the International MOLTEN Conference series was established to provide a forum to bring together leading academic researchers and industrial engineers to present and discuss the latest scientific ideas and findings, and their application in their respective fields. This article presents an analysis of the research carried out in this field over time in terms of the number of journal articles, fields and slag systems studied and geographical origin of the research.

Jun 19, 2024

By P Breuer, A Simons

The sulfidisation, acidification, recycle and thickening (SART) process is currently being used at NewcrestÆs Telfer Gold Mine to recover cyanide and copper from the cyanidation tails of the pyrite concentrate carbon-in-leach (CIL) process. While the process has been effective at attaining high recoveries of cyanide and copper, the Telfer SART plant has experienced higher than expected sulfide additions to achieve these recoveries. This paper details the results of surveys on the Telfer SART plant, which show that residence time appears to be causing the high sulfide consumptions. The paper also details the results of laboratory scale experiments which confirm the observed residence time impact during the acidified stage of SART.CITATION:Simons, A and Breuer, P, 2013. The impact of residence time on copper recovery in Telfer Gold MineÆs cyanide recycling process, in Proceedings World Gold 2013 , pp 189-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Murphy, I Samsonova, N Eastwood, D Whittle

Part XI of the United Nations Convention on the Law of the Sea (UNCLOS or the Convention) (United Nations (UN) Division for Ocean Affairs and the Law of the Sea, 1982) establishes a comprehensive regulatory framework for the conduct of deep seabed mining (DSM) activities of mineral resources in the Area (defined in Article 1(1) of UNCLOS as ‘the seabed and ocean floor and subsoil thereof, beyond the limits of national jurisdiction’). Under that framework, DSM activities can only take place in the Area pursuant to an approved Plan of Work in the form of a contract with the International Seabed Authority (ISA) (the Authority), a 168-member international body created under UNCLOS to administer the Area. Private contractors can undertake DSM activities if they are sponsored by Member States of UNCLOS, providing a dual system of international and domestic regulatory control and oversight for activities in the Area.

Sep 1, 2024

During the past three years Lurgi's Circulating Fluid Bed (CFB) technology has been successfully applied to roasting of refractory gold ores and con- centrates. In comparison with the so-called Stationary Fluid Bed roasting systems, a considerable improvement of gold recovery, to around 95 per cent, has been demonstrated and achieved on many occasions in pilot CFB units and in commercial CFB roasting plants as well. The major reason for such improved gold recoveries is the excellent controllability of the roasting process in the CFB reactor system. Here, temperature, gas atmosphere and solids residence time are more precisely controllable at optimal values during roasting operation in order to achieve the highest possible gold recovery in the subsequent leaching process step. Further dominant benefits of CFB roasting systems are their flexibility with regard to feed material, throughput capacity, dry or slurry feed, almost unlimited oxygen enrichment, direct fuel addition and in situ capture of SO2 in the presence of limestone and dolomite. The system will accept 50 per cent turndown ratio, large variations in feed composition and particle size, as well as a variety of different fuel types. The commercial applications of CFB roasting systems for gold con- centrates have been realized so far at Fimiston, Kalgoorlie/Westem Australia and for whole ores at Cortez, Nevada/USA.

Jan 1, 1991

By A N. Terblanche, D S. Smit

The paper discusses the improvements achieved after an external sparger flotation column, 1.42 m diameter by 9.5 m high, was installed as a re-recleaner unit at the Northam Platinum LtdÆs UG 2 plant in South Africa. The paper also evaluates the pilot plant data prior to the industrial size column installation as well as the accuracy of scale up from pilot to full-scale operation. Since the installation of the PrepQuip flotation column, the final concentrate upgrade ratio improved from 83 to 105, the 3PGM+Auå recovery improved from 79.7 per cent to 81 per cent and the Cr2O3 content in the final concentrate decreased from five per cent to 2.8 per cent. The upgrade ratio can be improved to 125 with an overall 3PGM+Au recovery of 80 per cent. Conventional mechanically agitated flotation cells achieved only 74 per cent recovery at an upgrade ratio of 125.

Jan 1, 2005

Declines for both access and rock haulage are replacing shafts for mining relatively shallow deposits of down to 1000 m below surface. Where the orebody does not outcrop and where surface access may be restricted, it is often necessary to drive long dead end headings before a connection can be made back to surface and a ventilation circuit created. In hot tropical areas and where large diesel powered equipment is used for mining, heat may also be a problem at these relatively shallow depths. The normal design criteria based on statutory limits and good practice used to evaluate ventilation and cooling requirements in terms of air velocity, dust, gases, diesel exhaust dilution, re-entry after blasting and heat stress are described in this paper. These are then used to design and cost alternative auxiliary ventilation systems that include leakage based on general fan performance curves and typical duct systems. The implications of the current European Community recommendations regarding nitrous fumes are also briefly considered. The actual problem relates to a 2100 m long decline that may have to be extended to 3000 m long without a connection to surface or through ventilation and is located in a hot tropical area where the surface wet bulb temperatures may exceed 25¦C for more than a third of the summer period. Once the preliminary ventilation design is completed, the auxiliary ventilation system can be modelled and simulations undertaken that incorporate heat and moisture transfer routines with the objective of determining the cooling load and amount of refrigeration required. Cognisance is taken of cyclic diesel operations and the thermal flywheel effect of the surrounding rock on the wet and dry bulb temperatures resulting from these operations.A suitable modular cooling system located at the portal is described and optimised with capital and operating costs of both the ventilation and cooling systems provided.

Jan 1, 2005

By R Godard, J Gantumur, F Prince, C Pascoe

Resolution Copper Mining LLC (RCML) is one of the largest undeveloped high-grade porphyry copper-molybdenum deposits in the world, with an orebody at depths of approximately 2000 m beneath post-mineralisation cover. With a vision to develop a large-scale, low-cost operating mine, the project is designed as a micropanel cave with an advanced undercut.In September 2014, RCML began a study focusing on identifying and selecting the best production cases to eventually reach full production (120 kt/d). To achieve this, a methodology was developed that allows the fast evaluation of a large number of production schedules.Dassault Systèmes GEOVIA was commissioned to enhance the Footprint Finder program for batch scheduling panel cave production. The tonnage and grade schedules produced by Footprint Finder were compared to schedules developed using personal computing block caving (PCBC™). The inputs to Footprint Finder were then adjusted to achieve a reasonable correlation with the PCBC™ schedules.The enhanced Footprint Finder program was used to batch-process nearly 54 000 schedules using 20 elevations, 17 shutoff grades, four heights of draw, two different copper grades (modelled and upside), two layout refinements within the existing footprint and a variety of production ramp-up rates to 120 kt/d. The study team developed processes to analyse large amounts of data, to assist in selecting a matrix of the best schedules for detailed assessment using PCBC™. Three hundred PCBC™ schedules were developed.The detailed trade-offs between the scenarios is currently underway with promising results. This paper outlines the methodology used in evaluating the numerous alternatives.CITATION:Gantumur, J, Godard, R, Prince, F and Pascoe, C, 2016. Development and evaluation processes of cave production schedules for the Resolution copper project, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 59–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016