Search Documents

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By G Cao, Y R. Cui, J X. Zhao, H P. Gui, G H. Wang, Z M. Wang, M M. Ren, B Li

Pyro-metallurgy is still the main process for lead production and a lot of lead direct smelting processes have been developed in recent years. All the processes will experience two steps in common. The first is the oxidisation of PbS to PbO and then reduction from PbO to Pb, furthermore, from ZnO to Zn. So, the composition of melts, especially the slag composition at reduction step change continuously. Up to now, there are few systematic results on the slag physical-chemical properties with its composition change. In this work, the typical lead direct smelting processes were analysed from theoretical and practical standpoints. The full-period slag composition and slag melting point change were compared. Especially, to the PbO and ZnO reduction steps, based on the full-period slag composition change, the slag properties were predicted. Based on dust composition and test results, the mechanism of Pb compound evaporation and its effect on practice and measurement of high PbO bearing slag physical-chemical property is discussed. It is suggested that to restrain the evaporation in practice and to obtain more accurate measurement results of physicochemical properties of smelting slag are the key problem not only to set high efficiency, energy saving process, but also to environmental pollution control.

Aug 21, 2024

Much of the coal and gold mining industry of New Zealand is small scale. Funding is tight and mechanisation limited. The country has many well documented small coalfields (some with significant outcropping) and alluvial gold deposits. These are generally remote, difficult to access (physically and otherwise) and of submarginal value (largely a consequence of size when viewed for extraction by traditional techniques). The industry is also burdened by environmental and bureaucratic constraints. The above over simplified setting suggests to the Author, a newcomer to New Zealand, the opportunity to consider some novel concepts based on technology and techniques developed overseas or borrowed from other industry sectors. The objective being to make viable in economic and environmental terms projects that might otherwise be stillborn if considered for exploitation by conventional means. The paper mainly discusses 2 concepts focusing on the application of augers for exposed high wall or outcrop coal and micro-tunnelling augers for alluvial gold extraction. These may be considered high mobility 'container' (as in shipping container) packaged, or 'non invasive' mining systems. It is stressed that these are but concepts and have yet to be subjected to rigorous financial or engineering scrutiny. This could only follow their acceptance by, and input from, New Zealand miners. There will also be brief mention of a new modular conveyor system which might have application within the concepts or existing small scale mineral extraction operations and mention of a project currently in progress to apply tangible 'sustainability' to underground coal mining.

Jan 1, 1996

The mechanization of the coal industry in New South Wales involved the introduction of large face and transport machines. The trend is towards still higher capacity units with .greater horsepower and it became apparent that a potential risk of damage to the hearing of workmen existed. In order to assess whether the sound levels were SUfficiently high to impair the hearing of workmen a sound level survey of all major operations in the industry was carried out by the Mining Engineering Division of the Joint Coal Board.The results indicated ·that the operations could be classified into three categories of risk, probably hazardous, of doubtful hazard due to the intermittency of the operations, and of low hazard.Legislation has subsequently been enacted requiring the wearing of hearing preservation aids in some of the probable risk operations.

Jan 1, 1974

The suitability of char from Yallourn brown coal as a filler for carbon electrodes used in the aluminium smelting industry has been assessed on the basis of the specifications usually laid down by electrode manufacturers for petroleum coke fillers. The purity specifications can be met by a simple acid leaching of the coal before carbonization. The true density of char produced at 1200°C is within 5 per cent of the specification figure, but the bulk density of char obtained from as-mined coal is only half that specified for petroleum coke.Although this can be increased to three-quarters of the specified figure by briquetting the coal before carbonization, further increases would be very difficult to achieve, as the remaining shortfall in density is due to an extensive microporosity developed in the particles of char during carbonization.

Jan 1, 1970

By P Klaric, N Swart, S Barnes

The recent advances in digital imaging technology, specifically around photogrammetry, have facilitated precision measurement in the difficult conditions encountered in an underground development mining environment. With the recent downturn in the resources industry, many mining houses have begun to focus on cost reduction projects and driving efficiencies. The application of digital photogrammetry has allowed greater insight into the development mining cycle and supported a focus on areas where efficiencies and cost savings can be achieved. Data collation, via digital image capture, can be completed with minimal disruption to the development mining cycle with analyses taking a nominal time to process and interpret. The result can be a stark visual representation of the result of blasting and associated activities of the development mining cycle. Many millions of dollars of benefit can be derived from understanding the impact of each component of the development mining process, with some of the biggest savings associated with conformance to drill design and the minimisation of overbreak during blasting. This paper will explain the image capture process, analyses and instigated improvement opportunities that were undertaken at a number of mine sites to improve efficiencies and drive savings in their development mining processes.CITATION:Klaric, P, Swart, N and Barnes, S, 2017. Digital imaging provides valuable insights into underground development mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By S Kakara, A Kamaraj, S S. Varanasi, B V. R Mandalika, M B. Shaik

The properties of top slags play a very important role in secondary steelmaking. Fluxes should be chosen based on the ladle furnace (LF) slag requirements like viscosity, melting temperature, sulfide capacity, etc. CaF2 and CaO-Al2O3-based synthetic slags are the most used fluxes in secondary steelmaking to improve slag fluidity and interfacial chemical reactions. CaF2 is obsolete due to fluorine pollution and CaO-Al2O3 based slags have 40–50 wt per cent Al2O3 and 30–40 per cent CaO which is not beneficial for desulfurisation. Yet another drawback is that LF slag disintegrates into fine powder during cooling due to phase transformation C2S (2CaO.SiO2). Hence, there is a need for the development of low melting fluxes with high CaO content and the capability to prevent slag disintegration. The current work studied the effect of 0–9 wt per cent B2O3 on physico-chemical properties and characterisation of LF slags. X-ray diffraction (XRD) analyses were carried out to identify mineralogical phases present in slag and Fourier-transform infrared spectroscopy (FT-IR) analysis was done to understand the changes in bonds of B2O3 added LF slag. The characteristic temperature of slag was determined by a hemispherical method using high-temperature microscopy. Empirical models were used to calculate viscosity, break temperature, and sulfide capacity. FactSage™, ver 8.2 (by GTT-Technologies) simulations were carried out to find the equilibrium phase fractions and percentage of liquid slag at different temperatures. New phases such as Ca11B2Si4O22 and Ca2B3O5 were formed in LF slag with B2O3 addition. Based on the results, 0.5–1.0 wt per cent B2O3 was found to be sufficient to prevent C2S-driven disintegration of LF slag. Also, the melting temperature and viscosity of LF slag were reduced by adding 3–8 wt per cent B2O3 due to the formation of BO3 planar triangular structure and low melting eutectics in slag. Liquid slag started forming at a temperature as low as 800°C when B2O3 is >6 wt per cent. It was found that the sulfide capacity, viscosity, and break temperature of the slag decreased with increasing wt per cent B2O3. Based on the analysis carried out, B2O3 can be a promising fluxing material in secondary steelmaking, for improving the desulfurisation kinetics and valourisation potential of LF slag.

Aug 21, 2024

By B L. Dickson, E, M F. Lee, P A. Mikula

Computational techniques are needed to assist in the analysis and interpretation of the increasing amounts of geoscientific and mining related data and information that are routinely gathered at mine sites. New interpretation methods are needed to provide an integrated approach so as to establish relationships (cause and effect) or to be predictive about possible outcomes based on acquired data. Traditional multivariate statistical methods are often confused by variable relationships that are non-linear, data distributions that are non-normal, and by the data themselves that may contain missing values, text and both continuous and discontinuous numeric values. Modern data mining methods are available to understand the relationships within and between diverse data sets, and identify relationships or trends associated with processes, measurements and mine design parameters in mines. The self-organizing map (SOM) is a data mining approach with the advantage that all input data samples are represented as vectors in a data-space defined by the observations (variables). The SOM procedure is an exploratory analysis tool that highlights patterns and relationships. Results are internally derived, in an unsupervised fashion based on measures of vector similarity. Our SOM outputs are highly visual, which assists in understanding and illustrating the dataÆs structure and internal relationships. Two studies are presented. The first uses SOM to investigate the relationships between a range of measured and derived rock property parameters and their observed behaviours during mining. Our aim was to determine whether a SOM analysis would allow a better understanding of observed and predicted rock behaviours from their rock properties. The SOM analysis showed that there were indeed relationships between æbrittleÆ, æsugaryÆ, æslabbyÆ and æsqueezingÆ rock behaviours and a number of the input parameters. The computed SOM æstructureÆ was then used to assess the likely behaviour of unknown samples by assigning them into behavioural fields based on their measured and derived geotechnical responses. The second study was aimed at assessing whether a SOM analysis of microseismic data at the Kalgoorlie Consolidated Gold MineÆs (KCGM) Mt Charlotte mine can contribute towards understanding and potentially forecasting/minimising seismicity at the mine-design stage. The database comprised 40 sample æclustersÆ of microseismic parameters from the MS-RAP software package, which were derived from 2500 individual seismic events. The SOM analysis showed that some of the initial mining conditions are related to the seismic parameters. In each of the studies, the SOM procedures assisted in understanding the data and provided new insights. Because of its æordered vector quantisationÆ foundation, the SOM procedure is a substantial improvement over traditional statistical methods in three main areas:its ability to analyse data from disparate sources, including different data types; its ability to analyse sparse data sets with missing values; and its ability to analyse and visualise non-linear relationships within a data set.

Jan 1, 2006

By J G. McLellan, B Miller

Copper and Gold mineralisation at the Ernest Henry deposit is bound by two controlling shears along the hanging wall and footwall margins. The shear zone geometries have been influenced by a large diorite intrusion, dated at ca. 1660 Ma, which lies to the north-east and south-west of the main orebody. The shear zones, which partitioned strain prior to the main mineralising event ca. 1514–1504 Ma, and in conjunction with adjacent regional structures, have been a critical factor in the deposit location and geometry. Conventional exploration techniques have been utilised proximal to the current deposit since the initial discovery in order to expand upon known resources, with limited success. However, new geomechanical modelling techniques have now been employed to target structurally controlled mineralised zones in three dimensions. The main aim of the geomechanical modelling was to simulate the effects of regional deformation events to highlight areas of anomalous strain, which indicate areas with a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE-SW compression) to examine preconditioning of the system, and a D4 event (SE-NW compression) which have ultimately been responsible for the current location of the mineralisation.CITATION:McLellan, J G and Miller, B, 2017. Geomechanical modelling of the Ernest Henry iron oxide copper gold deposit – identifying fluid pathways to predict potential mineralised zones, in Proceedings Tenth International Mining Geology Conference 2017, pp 75–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By P J. Vardon, L A. van Paassen, Y Yao, A F. van Tol

Thin-lift atmospheric fine drying (AFD) is a technique used to dewater mine and oil sand tailings, which utilises both self-weight consolidation and atmospheric evaporation. The disposed layers undergo a cyclic drying and rewetting process due to precipitation and deposition of additional lifts on top of the dried layer. The current research aims to optimise the deposition process via use of a numerical model and realistic atmospheric conditions, including both periods of drying and wetting. The model is based upon water balance and includes large strain considerations. A number of material behaviours are characterised using empirical fitting curves based upon laboratory measurement of material characteristics, including both the shrinkage and water retention curves for drying and rewetting. The model is able to model multiple lifts, simulating field scale and realistic climatic conditions within timescales suitable for engineering practice (eg seconds or minutes). The model has been previously validated against controlled laboratory experiments and utilised to simulate field tests. A series of simulations are presented to illustrate the ability of the model to be used as a practical tool for the optimisation of a tailings deposition strategy.CITATION:Vardon, P J, Yao, Y, van Paassen, L A and van Tol, A F, 2015. The use of a large-strain drying and consolidation model to optimise multilift tailing deposits, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Bertuzzi

This paper presents a three-dimensional analysis of a trapezoidal-shaped segmental tunnel lining for a recent tunnelling project in Sydney. Two- dimensional analyses, hand calculations and equipment selection defined the lining geometry and loads. The analysis, which was undertaken using 3DEC (Itasca), included a complete ring of six segments bolted together to assess the impact of imperfectly built rings. Asymmetry was induced in the analysis by unfavourable positioning of segments within construction tolerances. Model output includes displacement and stress within the entire ring and normal, shear and bending moments at the joints. For the case analysed, the results suggest a 10 mm construction tolerance increases normal and shear stresses along the radial joints by approximately 25 per cent and 15 per cent, respectively and up to a doubling of the induced moments.

Jan 1, 2008

A paper presenting an overview of legislative and best practice approaches to the management of OHS&E and business risk for Australian tunnelling operations. Best practice can be achieved in Australian tunnelling through ærisk awarenessÆ by decision-makers and line personnel. This will identify problems before they occur and lead to implementing controls appropriate to avoiding loss throughout the life cycle of the underground opening. The author draws on legislative approaches from all Australian states together with practical experience from risk management and risk engineering work from six recent tunnelling projects. This describes a process that:commences with concept risk assessment,involves quantification of major hazards,conducts assessments of operating risks, andleads to implementation of an integrated management system that keeps construction activities connected with the controls identified in the design and planning phases and minimises the losses sustained as a result. Key points addressed include:where the industry is going with respect to risk û methods and considerations,how tunnelling risks are perceived by the industry and legislation,how tunnel constructors and owners can minimise exposure by using proper risk engineering ætoolsÆ, andreflections on best practice methods for transferring knowledge from designers to contractors/operators.

Jan 1, 2008

Project developent proceeds by increasingly detailed studies addressing overall project returns through an analysis of the substance, risks and costs associated with the following elements: ò Reserves ò Mining ò Processing ò Infrastructure ò Environmental Impact ò Product Market Computer-based expertise has a potential to ò Capture perishable expertise, making this available for shared access and so reducing the cost of human experience ò Consolidate know-how for optimising process operations, bringing consistency of judgement and advice to decision- making by making the rules, facts and preferences explicit ò Allow assignment of the basis and authority of decisions, so experts can pass routine expertise down the line, freeing their time to generate more. ò Force a review of expertise when creating the knowledge base.

Jan 1, 1989

By J Taylor, M Smith, A Tunnadine, D Nikolakopoulos

As Olympic Dam rapidly expands into the Southern Mine Area (SMA) the Mine Geology team has concurrently ramped up underground diamond drilling to sustain rates of above 175 km/a. With >10 underground rigs double-shifting, traditional paper sections used for the management of drill programs were no longer optimal due to scale of operations. An opportunity was identified to modernise monitoring of all underground diamond drill programs, through the integration of logged copper sulfide estimates with Olympic Dam’s first-fully integrated deposit-scale geological model in Leapfrog Geo. This paper describes the transition within the Mine Geology team from reliance on 2D paper sections, towards near-real time 3D geological modelling for optimising end-of-hole decisions in the field. This transition was enabled by innovative database solutions informing locally constrained implicit models, limited by a distance buffer around active underground fan drilling. Due to the high volume of historic drilling, there were significant computational challenges with the implementation of daily production style implicit models at Olympic Dam and initial testing of regular updates to implicit gradeshells and sulfide domains required in excess of 12 hrs to run. The enabling solution was to optimise the interfaces between the AcQuire database, Deswik MDM and Leapfrog Geo to create a dynamic, streamlined workflow that was easily completed by Mine Geologists in accordance with daily production duties. Geologists are now building rapid implicit models for a range of variables from an integrated data set of logged sulfide estimates and existing assays, spatially constrained by 150 m buffers around active drilling using a unique drill fan identifier flagged during the planning phase. Once the live-implicit models are updated, they are exported for visualisation on field tablets to be used during logging and core checks at the start and end of every shift. To manage the risk of ‘going digital’ interpretation remains at the forefront of the drill section close-out process, with Mine Geologists critically reviewing the finished sections on a standardised template with new learnings wireframed and communicated to stakeholders. The Live Field Model has enabled a step-change in the geological effectiveness of diamond drilling, reducing over – and under-drilling ore-waste at Olympic Dam continuing to push drilling effectiveness towards 20 per cent of intercepts >2 per cent Cu. In addition, upside or risk identified during the proactive management of drilling execution can be rapidly capitalised or mitigated.

Mar 22, 2022

By B Taylor

The Perseverance deposit is the most southerly known economic copper/gold deposit within the Cobar gold field. The deposit is situated approximately 12 km to the south-southeast of Cobar and is essentially blind to surface with the top of economic mineralisation occurring 750 m below ground level.Based on the December 2010 resource estimate (inclusive of reserves and net of depletion) the deposit contains 3 011 000 tonnes at 6.1 g/t Au and 0.90 per cent Cu (590 000 oz of gold and 28 000 tonnes of copper). The deposit is comprised of four principal lenses, the Perseverance, Hulk, Zone B, and Hercules lenses. In excess of 90 per cent of the known resource tonnes are contained within the Perseverance and Hulk lenses. The deposit is shear related and hosted within lower Devonian rocks of the Cobar Basin. The competency contrast of rhyolites juxtaposed against sediments by the Peak-Perseverance shear is the principal control on mineralisation. Both the Perseverance and Hulk lenses are primarily hosted by brecciated rhyolites juxtaposed against Chesney formation sediments across the Peak-Perseverance shear. This faulted rhyolite sediment contact roughly defines the global orientation of the deposit. The Perseverance lens continues within the shear for up to several hundred metres beyond the extent of the faulted rhyolite sediment contact. Mineralisation within the shear beyond the faulted rhyolite contact zone is hosted by sheared silicified sediments. The Perseverance lens remains open at depth and to the south.The Zone B and Hercules lenses, which are significantly less important in tonnage terms, are hosted by rhyolite breccias within the main body of the rhyolite and appear to be only tenuously related to the Peak-Perseverance shear. Within the Perseverance lens, the presence of northeast trending high grade breccia veins developed oblique to the north-south trending shear system has led to the development of steeply north plunging high grade ore shoots within a globally north-south trending mineralised domain. These high grade shoots have limited horizontal continuity but significant down plunge extent.The presence of coarse gold and the resulting strongly skewed nature of the gold grades, in conjunction with controls on mineralisation which are not parallel to the mineralised domain, has led to predictive difficulties regarding stope performance.Strong heterogeneity of the gold content of the ore and geological controls on mineralisation which are not parallel to the global trend of the mineralisation impose a set of difficulties which sound geological control is helping overcome.

Aug 22, 2011

By S Jeon, K Haga, A Shibayama, L Godirilwe, C B. Tabelin, I Park, A Buronov

Open pit/underground mining and mineral processing can generate large amounts of waste that contains sulfide-type minerals such as pyrite (FeS2), and it can produce acid mine drainage (AMD) when exposed to oxygen and water. This highly acidic wastewater contains heavy metals and this is one of the most serious environmental issues after mining operations taking several decades to completely remediate with high costs. For green mining, the present study focused on the development of a recovery technique for gold from an eco-friendly solvent, thiosulfate, by utilising mine wastes, tailings. First, gold recovery experiments in ammonium thiosulfate system were carried out using model samples representatively present in tailings (ie SiO2, Al2O3, FeS2, Fe2O3, and Fe3O4). The results showed that gold recoveries were negligible when using Al2O3, SiO2, Fe2O3, and Fe3O4 while pyrite shows a recovery efficiency three-fold as high as the maximum recovery efficiency when using others. Subsequently, the study also addressed the identification of the recovery mechanisms and post-recover process. The results indicate that tailings can be sufficiently utilised for gold recovery in the hydrometallurgy process and a further sustainable process can be established.

Sep 1, 2024

By J Crosbie, M Lord, R Bitencourt, P Defferrard

The MMG Century mine, which is the largest zinc/lead mine in Australia, began operating in 1999 and ceased mining from the open pit in July 2015, with processing completed in early 2016. Closure plans were developed from 2006, and detailed planning for closure commenced in early 2011 with the appointment of a dedicated closure planning resource. The site will continue to be managed during the active and passive closure phases to complete rehabilitation commitments and demonstrate that closure completion criteria have been achieved.Completion of the mining/processing phase of the project provides an opportunity to reflect on successes, missed opportunities and lessons learnt with respect to planning and execution of mine closure. This paper highlights examples of success at Century and also identifies key learnings and areas for improvement in progressive closure outcomes. Specific examples examine mine planning and execution involving bulk movement of waste rock and construction of permanent waste encapsulation landforms. The paper also provides recommendations for other sites that are planning for closure.Decisions made during the operational phase of the project life can result in a significant increase in closure liability and reduce the likelihood of achieving lease relinquishment. Likewise, it is of paramount importance to assess the consequences and thoroughly understand the risks associated with changes or deferral of closure plans, progressive rehabilitation targets and closure related key performance indicators.CITATION:Lord, M, Bitencourt, R, Crosbie, J and Defferrard, P, 2016. Closure planning lessons Learnt from the Century mine, in Proceedings International Mine Management Conference, pp 207-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By P Yß±ez, G Ferguson

The El Teniente mine produces more than 340 000 tonnes of fine copper per year from an industrial complex of underground mine, concentrator and smelter. Mass caving methods are employed to deliver approximately 95 000 tpd of ore to the mill, from a number of sectors underground, each sector being in effect a large-scale mine in its own right. This mining activity has faced challenges over the course of the last century such as:the capacity of the underground mine has been expanded to maintain and increase output of fine copper; the increasing size of the ore fragmentation forced to change the mining method to achieve the high productivity and profitability required in the business; and to modify the mining methods to continue mining at depth with safety. Fundamental activities in these mining methods, for the successful initiation of caving and subsequent draw, are:undercutting the base of the block or panel by blasting; and excavating of drawbells. The undercutting design evolves mainly on the height of the blasting to manage the change on ore fragmentation. The methodology move away from incorporating massive areas, typical of the block caving method, to a continuos blasting, typical of the panel caving method. Drawbell design changes on geometry, dimensions and sequence of excavation to deal with a corse ore fragmentation and the resolution of mining difficulties in the form of major rock bursts and collapses of production facilities. This paper focuses upon the evolution of the undercutting and drawbell design used at El Teniente mine and techniques under consideration to deal with future caving operations to provide the bulk of the daily production for the foreseeable future.

Jan 1, 2000

By A Gustafson, D Johansson, K Jonsson

The underground mining process, from in situ characteristics of the unmined rock mass to the final mill product with fully liberated minerals, consists of a chain of unit operations. Some of them influence fragmentation while fragmentation impacts others. From a production point of view, fragmentation is a key parameter for the proper functioning of many unit operations and affects total production; it influences the ability to load, haul and crush the rock later in the process. Fragmentation varies because of rock mass strength, the presence of joints, the chosen explosive, specific charge (kg/m3) and quality of drill holes. The efficiency and result of unit operations such as drilling, blasting, loading and crushing depend on the rock properties, which vary throughout a mine. Generally speaking, operations are not well adapted to the actual rock properties, leading to a non-optimised flow in production. This paper presents the initial part of a project that will build knowledge on the impact of fragmentation on each step of the production chain in an underground mine. It identifies the key parameters of fragmentation, which influence the overall energy consumption and productivity in a mining operation through interviews, mine visits and a literature review. In the subsequent stages of the project, a number of field tests in the case study mine will address important segments of the production process where fragmentation is a major obstacle to improvements. Optimising the entire process, rather than isolated unit operations, will lead to increased productivity, decreased amount of interruptions and lower energy consumption.CITATION:Gustafson, A, Jonsson, K, Johansson, D and Schunnesson, H, 2016. From face to surface – a fragmentation study, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 555–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A Manzoori, M T. Shadloo

This paper describes a CFD modelling study which was carried out to investigate possible improvements in the design of an alumina precipitator tank at the Jajarm plant of Iran Alumina Company. In particular, the tank has an impeller located very close to the tank bottom, such that it quickly becomes covered with settled solids after a shut-down of the agitator, making it difficult to restart. A CFD model was firstly set up in which the existing design was evaluated in terms of flow pattern, off-bottom suspension and distribution of solids, and power consumption. Further simulations were then carried out to test alternative designs, leading to a recommended design, which maintains good mixing, with the same power consumption and without the use of a low-clearance impeller.

Jan 1, 2006