Search Documents

By Morrison AL

The volume changes occurring during the reduction by hydrogen of single, high-grade hematite pellets under isothermal and non- isothermal conditions were investigated using a time-lapse photographic technique. The major cause of swelling during iso- thermal reduction at temperatures in the range 600-1000¦C, was the disruptive stresses set up during the transformation of hematite to mag- netite. The severity of the disruption was temperature dependent; the degree of swelling increased with increases in the reduction temp erature. Under non-isothermal reduction conditions, in which the pellet temperatures were increased at constant heating rates over the temperature range 500-1000¦C, minor swelling (6-8%) occurred in the initial stages of reduction followed by pellet contractions of up to 15% in the final reduction stages. The low initial swelling and high final pellet shrinkages were due to a com- bination of the temperature dependence of the swelling mechanism, and the sintering of fine pores in the reduced iron in the latter stages of reduction at higher temperatures.

Jan 1, 1980

By H Ramandi, H Masoumi, I Canbulat, B Hebblewhite, J Oh, S Saydam, W Timms, S Mo

This paper reviews the floor heave mechanisms in underground coal mine roadways. Previous studies have reported three main failure mechanisms: bearing capacity failure, buckling and swelling. The buckling failure has been observed where immediate floor strata are relatively strong and thinly bedded. On the contrary, the weak floor strata have been associated with both the bearing capacity failure and swelling mechanisms. The bearing capacity floor failures are likely to induce other types of instability such as pillar punching, tensile failure of pillar, roof fall and subsidence as well as floor heave. Despite a considerable amount of research, predicting the magnitude, location and timing of floor deformation is challenging with current state of knowledge. CITATION:Mo, S, Ramandi, H, Oh, J, Masoumi, H, Timms, W, Canbulat, I, Hebblewhite, B and Saydam, S, 2018. A review of floor heave mechanisms in underground coal mine roadways, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 196–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K W. Mills, N R. P Baczynski, J Mylvaganam, D A. Prado, M F. Lee, I A. de Bruyn

"This paper presents the second part of a study of the assessment of rock stress inputs on the performance of various new mining designs at the Ok Tedi large open pit mine in Papua New Guinea. Over the years, four programs of rock stress measurement have been completed at Ok Tedi, each providing different interpretations of the in situ field stresses. Details of three of these programs and interpretations are provided in the precursor to this paper, entitled ‘Rock Stresses at Ok Tedi, Papua New Guinea’ (Lee et al, 2014).This paper explains how the various stress interpretations were utilised in the modelling of the proposed new open pit and underground mining excavations, comparing where possible their expected effects on stability. The modelled performance of three specific mine components have been discussed here as case studies, including: the below-pit drainage tunnel, as the floor of the open pit workings is mined down from 350?m above, to within just 75?m above the crown of the tunnel the stability of the 1000?m high slope of the proposed West Wall cutback the proposed sublevel open stoping extraction sequence in the Gold Coast orebody beneath the East Wall, for which only the likely ‘worst-case’ stress regime was used to assess sequencing and stability issues.The benefits of scheduling the collection of detailed rock stress measurements and other input data from a range of different sources at various stages of the projects are discussed.Alternative in situ stress models have less stability impact on open pit slopes than on underground mine excavations.CITATION:de Bruyn, I A, Baczynski, N R P, Lee, M F, Mills, K W, Mylvaganam, J, and Prado, D A, 2014. The application of rock stress inputs to stability assessments at Ok Tedi Mine, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 43–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

By P Stephenson, G Mosher, M Berry, C Arnold, P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Globally, private minerals companies considering the transition to a public company and entrepreneurs looking to create a new public company through, for example, an initial public offering or by a reverse takeover have many options. For companies with assets around the Pacific Rim, there are arguably five key stock/securities exchanges that actively promote international minerals company listings, and these are located in Australia, Canada, Hong Kong, Singapore and the United Kingdom.Listing on any of these exchanges requires a range of technical, commercial, financial and legal documentation. Each exchange has specific rules and requirements for technical documentation to support the listing process. Once listed, each exchange also has specific rules for technical information to meet ongoing compliance requirements. The nature and detail of this documentation differs for the five exchanges.This paper presents statistics on the minerals company listings on each exchange and provides an overview of the technical documentation required to prepare for an initial listing and ongoing compliance.CITATION:Berry, M, Stoker, P, Stephenson, P, Arnold, C and Mosher, G, 2015. Technical considerations of public listing and ongoing compliance for minerals companies , in Proceedings PACRIM 2015 Congress, pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Brathwaite RL

The gold-scheelite-quartz lodes of the Wakamarina valley were the most productive of the mesothermal gold-bear in the Marlborough Schist. Most of the production came from the Empire City and Golden Bar mines which worked tug, Golden Bar lode. Only 134 m of its 1800 m strike length are accessible, in the No. 2 level of the Golden Bar Mine. A fau I has downthrown the Golden Bar Mine section by 2 47 m and displaced it left-laterally by 18 m. The lode is a typical ribbon-banded mesothermal vein, averaging c. 1.75 m wide, and enclosing narrow horses of schist country rock. It i composed of bands of milky "buck" quartz with thin laminae of schist. Scheelite occurs in short strings of grains withi quartz on the footwall side of the lode and also in small quartz-carbonate veinlets in the foot wall and hanging wall schist The lode quartz contains only localised traces of pyrite and arsenopyrite. They are more abundant in the wall-rock schist.

Jan 1, 1995

The Pongkor Gold Mine employs 678 staff. The mine is owned by the Indonesian state company PT Antam Tbk and is located 100 kilometres south west of Jakarta, in Java, Indonesia. Mine and infrastructure development started in 1992 following intensive geological exploration over 15 years. First gold production was in June 1994. The mine comprises three main orebodies: Ciguha, which is nearly mined out, dips at 75¦ from surface to 150 m. Kubang Cicau, dipping at 80¦ from surface to 230 m, and averages 3.5 metres thick at a grade of 10 g/t Au and 128 g/t Ag; and Ciurug, dipping at 60¦ from surface to 300 m and averages eight metres thick at a grade of 14 g/t Au and 172 g/t Ag. Present global ore reserves are 4.6 million tons at a grade of 12.3 g/t Au and 133.6 g/t Ag. Exploration is continuing for new veins. Initial mining was by manual cut and hydraulic fill at Ciguha, followed by Kubang Cicau. In 1996, it was proposed to convert Ciurug to a mechanised cut and fill operation. Two single boom jumbos and three load-haul-dumps (LHDs) were purchased with the assistance of a gold loan from NM Rothschild and Sons. Implementation of this upgrade was delayed by both a national economic crisis and an invasion of the concession by illegal miners. It was not until May 1999 that raise bore vent rises and access drift infrastructure commenced. Major underground development started in 2000 and is continuing. Production cut and waste fill stoping started in July 2001. The change from manual to mechanised methods has required a total change in work practices and attitudes. However, the process has resulted in a production increase from 600 tpd to 1200 tpd. A three-month compliance test (a condition of the financing loan) was successfully completed, from July to September 2001, with an average production of 700 tpd at Ciurug and 500 tpd from Kubang Cicau.

Jan 1, 2002

Analysis of Electrostatic Separation for Rutile Cleaning Duty Using a Plate Electrode Assisted High Tension Roll Separator A plate assisted electrostatic high tension roll separator has been used for the removal of impurity mineral grains from a rutile rich product stream. A laboratory study and a subsequent production study explored the effect of machine conditions with a view to the optimisation of the separation performance of the separator. The performance requirement was that the TiO2 grade in the non-conductor stream was to be less than ten per cent whilst at the same time the ZrO2 grade in the conductor stream had to be less than 0.5 per cent at mass recoveries of greater than 90 per cent to the conductor stream and less than 5 per cent to the non-conductor stream. Mineralogy data was utilized to determine the feasibility of achieving the production targets with the feed under study. Since the feed stream mineralogy was dominated by rutile, leucoxene and zircon, it was possible to use an approximation to the actual mineral assemblage as well as the raw X-ray fluorescence data to understand the separation duty of the Carrara machine. Since there were four conflicting criteria used for the performance requirement, an index was devised that incorporated all the requirements simultaneously. This new index was the sum of the squares of the difference between the achieved and desired values, weighted with respect to the variance of each variable. If the desired value for a particular criterion had been met its contribution to the sum was set to zero, no matter how well the criterion had been met. For the production machine the strict requirements were almost achieved. As expected, the achievement of the target performance was dependent of the feed conditions at the time of measurement. This paper reports the results of this study.

Sep 13, 2010

A drive, 3,500 ft long, was planned to explore mineralization exposed by diamond drilling. A rate of advance of 150 ft per fortnight, approximately double previous Broken Hill rates, was required. Subsequent to the completion of this drive its extension for a further 6,200 ft was planned to provide a main haulage way along which ore could be transported from a newly acquired lease back to the main hoisting shaft, a total distance of 13,500 ft.This paper describes the working conditions, relationships, manning and costs, and gives details of the cycle and equipment used to achieve rates up to 170 ft per fortnight.OBJECTIVEDiamond drilling from the 1,000 ft level at the Delprat Shaft section had indicated that the zone of mineralization, about 150 ft wide, which had been explored on the 1,000 ft level for a length of 2,600 ft, continued downwards with a westerly dip. The drilling results showed that within this wide zone there were arrower lenses of mineralization of possibly payable grade (see composite plan, Fig. 1).Diamond drill holes of 2,000 ft and over, particularly through heavily sheared areas of sericite schist, had been found to be costly, slow, and inadequate in testing the potential and trends of these smaller concentrations of mineralization.It was therefore decided that an exploratory drive should be advanced from the northern limit of the 1,480 ft level into the western mineralization, and that from this drive diamond drill holes should be drilled at dose intervals to outline the ore.The 1,480 ft level was chosen for the following reasons.1. It had the greatest northerly reach of the accessible levels at No. 7 Shaft section below the 1,000 ft horizon and therefore would enable the test to be made most quickly.

Jan 1, 1965

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By Y Peng, B Guo

In gold processing plants, the water from the cyanidation stages is treated to detoxify cyanide species and this recycle water becomes the main part of the process water. Despite the low concentration of free and weak acid dissociable (WAD) cyanides in process water, the recoveries of gold and silver is still affected during flotation, especially when gold and silver are associated with iron sulfide minerals. This is a case at the Hidden Valley (HV) Mine. In this study, the effect of free and WAD cyanides on gold and silver recoveries by flotation from the HV Mine was considered.WAD cyanide (WAD CN) was prepared by mixing sodium cyanide and copper sulfate at a cyanide to copper ratio of 3:1 dosed at different cyanide concentrations. It was found that both free and WAD CN depressed gold and silver and particularly iron sulfides in flotation. The depressed gold and silver recoveries were closely associated with the depressed recovery of iron sulfide minerals, suggesting that free and WAD CN may not depress the flotation of liberated gold and silver minerals significantly. It was also found that 10 ppm free cyanide completely depressed the flotation of iron sulfide minerals and WAD CN depression is probably through the WAD dissociation to free cyanide species (mainly aqueous HCN) during the grinding process, resulting from a decrease in pH. Thermodynamic calculation showed that 5.5 ppm free cyanide was released in the end of grinding at an initial WAD CN concentration of 50 ppm. This research provides a guideline to counteract the negative effect of WAD CN in the flotation of gold and silver minerals.CITATION:Guo, B, Peng, Y and Espinosa-Gomez, R, 2013. The effect of weak acid dissociable cyanide on gold and silver flotation in Hidden Valley Mine, in Proceedings World Gold 2013 , pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The stability of parallel underground coal mine galleries and pillars have been investigated using two- and three-dimensional (3D) numerical stress analysis. Anisotropic horizontal in situ stresses and the direction of the excavations have been considered in the numerical analysis. The stability of the tunnels driven in a coal seam at various working depths has been investigated taking into account different strata conditions and then results from two- and three-dimensional numerical modelling studies were compared. Maximum principal stress components have been chosen in three various directions: vertical, parallel and perpendicular to the tunnel axis. Analysis have shown that in the anisotropic in situ stress field, the favourable direction of underground mine openings which have different strata conditions depend not only on the horizontal in situ stresses but also on the vertical in situ stresses. Furthermore, 3D numerical modelling studies have been carried out to investigate stability of multiple entry longwall panel gate roads and pillars with various width-to-length ratios (W/L). Results of the modelling studies have shown that the critical dimension of coal pillars depends on their width and the direction of maximum horizontal stresses.

Dec 6, 2010

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

By Madgwick J. C

Powders prepared from the algae Gracilaria secundata, Ulva lactuca and Ecklonia radiatawere shown to provide sole nutritional support for microbial, microaerobic, biodegradation of low-grade manganese dioxide ore. G. secundata was the most effective bacterial nutrient giving 32 per cent recovery of Mn++, at an average rate of 63 mg Mn++/litre/day and a yield of 24 mg Mn++/g dry powder in microaerobic cultures containing 1.5 per cent (w/v)MnOz ore and 3per cent (w/v) powder over 14 days. Although G. secundata was approximately half as effective as molasses in supporting microbial decomposition ofMnOz, possible on-site growth ofthe alga could be economicaIIy more practical than transporting carbohydrate to a distant mine site.

Jan 1, 1987

By D Mnller, J L. Mauk

The Oblaga Cu-Au skarn deposit and porphyry prospect is located in the south-eastern edge of the Gobi Desert in western Inner Mongolia. The deposit occurs within metamorphosed middle Paleozoic volcanic, plutonic and sedimentary rocks.   Ivanhoe geologists recognise eight main rock types in the area. Calcareous sediments include conglomerate, interlayered siltstone-sandstone, and limestone. Covering the calcareous sediments is a slab of thrusted biotite granite, and above it is rhyodacitic lithic tuff which, in places, is overlain by alluvial sediments. Various plutonic rocks and related intrusion breccias have intruded these units. Monzodiorite, quartz-monzonite and monzonite tend to form thin, high-angle intrusions and the youngest andesitic intrusions are generally wider and subhorizontal.   The Oblaga Cu-Au skarn, which occurs in the calcareous sediments, shows typical prograde and retrograde mineralogy. Petrographic studies show that prograde skarn minerals have been overprinted by retrograde skarn minerals, and original host rock minerals have been texturally obliterated and completely replaced. The mineralogy of the Oblaga skarn deposit is very similar to other Cu-Au skarn deposits worldwide.   Sericitic and minor chloritic alteration occurs throughout the study area and may relate to porphyry-style mineralisation. Generally, this alteration is not intense and most rocks have retained their original texture. Geochemical analyses suggest that K-metasomatism is not widespread at Oblaga. XRD analyses suggest an upward and outward transition from sericitic to chloritic alteration.   Comparisons between Oblaga and other porphyry Cu-Au deposits worldwide show that Oblaga has very similar characteristics to deposits that have undergone sericitic alteration. However, Oblaga is special because it also has relatively intense chloritic alteration, which is uncommon in other porphyry Cu deposits described in the literature.

Jan 1, 2005

By P B. Hills

This paper discusses the computerisation of the drill hole database, some historical records and the creation of a three-dimensional model of the gold bearing structures for resource estimation and mine design at the Beaconsfield Gold Mine in northern Tasmania. The phase of the work reported here commenced in November 1997 and was completed in March 1998. The historical mining on the Tasmania Reef had reached a depth of 450 m below surface when work ceased in 1914. Production up to this time was 854 000 ounces gold. Recent activity has concentrated on testing depth extensions of the previously mined ore structure, to a depth of 1000 m below surface, and the establishment of an underground mining operation to exploit this resource. The lode structure at Beaconsfield is a typical mesothermal vein style deposit. Gold is contained within narrow quartz, carbonate and minor sulphide reefs or veins. Reef width is variable from a few centimetres to several metres with æsplitsÆ or bifurcations being common. The reef averages 2.7 m true width in the economic zones. The key feature of this style of mineralisation is that reef continuity can be confirmed by drilling to a high level of confidence, but the gold grades are somewhat more erratic in nature. The resource estimates were based entirely on drill data. The drill intercepts on the reef were coded for each split directly into a database and these allocations validated graphically. The distribution of grades and widths show an increasing gold grade with reef width for both the drill hole and historical data. The same histogram patterns, mixed populations and overall arithmetic average grade for the historical mine (at 21.52 g/t > 3 g/t Au) and new drill data (at 21.55 g/t > 3 g/t Au) would indicate that there has been no major change in the overall style or grade of the ore from the historically mined areas to the new resource. The reef, host geology, area of historical workings and resource zones at the Beaconsfield Mine were defined as a series of closed wireframes. The Tasmania Reef was modelled as five mutually exclusive wireframes, one each for the Main Reef, Footwall split, Second footwall split, Third footwall split and Hangingwall split. The data for this exercise was extracted directly from the drill hole database, stored in Microsoft Access format. The formation of the solids was largely automated with manual validation and refinements allowing for multiple runs using different interpolation methods and combinations of drill holes. A rotated 3D-block model in the plane of the Tasmania Reef was created to contain the grade model and allow for tonnage, grade and reef width estimates. An inverse distance squared (ID2) interpolation method was used with ranges of 25 m along strike and 125 m down plunge with blank areas infilled with 50 m by 250 m. Each reef split was filled separately using only drill intercepts from that split. The method was independently validated used MIK methods. Longitudinal sections have been prepared showing gold grade, reef width and width +grade. Estimates were also made for arsenic, sulphur and other minor elements. The long sections show three distinct mining zones. A method is presented for the conversion of the resources to reserves by the addition of mining parameters for minimum mining width, minimum pillar, cut-off grade and internal and external dilution. The selection is done on columns within the block model, and allows for all splits to be considered at once. Multiple runs can be made for varying combinations of parameters to test different mining methods and their impact on reserves, mine life and NPV.

Jan 1, 1999

By Alvin J. F

Tin in ores containing 0·025 to 1·5 per cent tin can be determined polarographically by the reduction of the chlorostannite ion at the dropping mercury electrode in 2M hydrochloric acid solution containing 15 per cent ammonium chloride. The tin is separated from interfering elements by distillation as the tetrabromide and collected from the distillate by co-precipitation with aluminium hydroxide. The method can detect 0·01 per cent tin in ore.INTRODUCTIONAn iodimetric method, suitable for routine analysis of titrating tin in concentrations down to 1 per cent, has been available for some years (Low, Weinig, and Schoder, 1939).As concentrations fall below 1 per cent tin, there is increasing difficulty in obtaining a distinct end point due to large amounts of iron and silica normally present after fusion of the ore. Since concentrations of tin down to 0·02 per cent are significant in ore dressing products it was necessary to examine methods to determine such low concentrations, and to adapt these to tin ores containing a wide variety of other minerals.EXPERIMENTALDigestion and separationCassiterite, the principal tin mineral, is refractory but readily attacked by a sodium peroxide flux to yield soluble sodium stannate. In a recognized procedure, a sample of ore is mixed with up to 15 g of sodium peroxide in an iron crucible and swirled over the full heat of a Meker burner for 7 min. The fusion is leached with water and acidified.This solution then contains tin, silica, and other soluble...

Jan 1, 1962

By S Watson, L Martinez

Mine projects are complex opportunities that demand a constant assessment of uncertainty, ie risk and upside potential. This is because the value of a mine project is typically influenced by many underlying economic and physical uncertainties, such as metal/mineral prices, metal/mineral grades, costs, schedules, quantities, and environmental issues, amongst others, which are not known with much certainty at the beginning of the project. But, is uncertainty an enemy or an ally of the mine planner/analyst? To answer this question, this paper first assesses and elaborates upon the general concept of uncertainty. It then looks at the different sources of uncertainty in a mining project, such as the orebody, costs and product price uncertainties, and their effect on the final project value. Next, a general?review?of current mine evaluation techniques highlighting their limitations when dealing with uncertainty is made. Finally, an extended evaluation and risk management framework that addresses the existing uncertainty in the (greenfield/brownfield) mine evaluation process is proposed. One important characteristic of this framework is that it uses and manages uncertainty in order to generate additional value to the project; this is done through operational and managerial flexibility, which allow mine planners to minimise/maximise project risk/upside-potential giving a more realistic estimate of the projectÆs market value - this is shown in practical and simple examples occurring at different stages of a mine project, such as exploration and operation. Final conclusions are provided at the end.CITATION:Martinez, L and Watson, S, 2012. Uncertainty - An important source of (additional) value for mine projects, in Proceedings Project Evaluation 2012 , pp 131-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By C Jenkins, M Mativenga, C Stanton, J Gerber

In 2014, Arrium completed an optimisation program on its magnetite concentrator, enabling a reduction in the overall cost base of producing concentrate through an increased ability to treat a wider range of ore types, previously considered waste. The development was the culmination of four years of work, conducted in house by Arrium’s mining development group. The overall intent of the plant design focused on improving the concentrator’s ability to treat a wider range of magnetite ore types. Metallurgical analysis of these feed ore groups outlined a need for more grinding power if production quality was to be maintained and throughput increased. As such, a tertiary grinding circuit was designed which, alongside the rectification of key operational bottlenecks, would allow the plant to continue to produce concentrate at the required specification and rate. The technology chosen for the tertiary grinding application was the XT IsaMillTM, which is known for efficient fine grinding when compared to conventional ball milling. The transfer sizes between the existing comminution circuits were coarsened, allowed for the treatment of different ores at the required rates. The optimisation project was successfully completed in February 2014 after a three month commissioning phase. The initial metallurgical testing and engineering of new equipment proved highly successful with all equipment meeting or exceeding design parameters.CITATION:Stanton, C, Mativenga, M, Gerber, J and Jenkins, C, 2015. Unlocking plant capability through targeted debottlenecking of Arrium’s magnetite concentrator, in Proceedings Iron Ore 2015, pp 185–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Rutter, E Amini, D La Rosa, N Beaton, M Scott, F Faramarz, L Keeney

Anglo American’s Los Bronces copper mine in Chile has been conducting detailed assessments investigating value adding options for their asset. The mine has conducted several detailed Mine-to- Mill and Grade Engineering studies to investigate increased throughput and head grade and to quantifying the impact of these approaches across the life of mine. CRC ORE has two key technologies namely Grade Engineering and the Integrated Extraction Simulator. These two technology suites have been combined to understand the technological landscape and associated value drivers suitable for application at Los Bronces. Detailed ore characterisation test work was conducted to:  measure and spatially model the propensity of ores to naturally deport and  develop customised blast models for Mine-to-Mill and Grade Engineering evaluation The outputs of this work were utilised to develop a block model populated with a range on new Grade Engineering and blasting parameters suitable for scenario analysis. To facilitate scenario analysis a high-fidelity value chain model of the Los Bronces operation from blasting to concentrate production was built in IES. IES was combined with sophisticated analytical tools such as Neural Networks to develop and reconcile a fully integrated value chain. The value chain model made it possible to simulate in IES all available blocks in the block model to predict throughput and grade changes for different strategic scenarios. The scenario analysis was run across 24 strategic combinations of Mine-to-Mill and Grade Engineering and comprised several million simulations. The scenarios investigated each technology independently and jointly to provide an attributed block model that can feed forward into technoeconomic modelling to determine optimal execution strategies for the mine. This paper presents the first published study combining Grade Engineering and IES to provide mass simulation capability to investigate strategic options for a mining asset.

Nov 10, 2020