Search Documents

By Palmer DJ, Bain JH, Pullen JB

Over the last ten years at Risdon, zinc production capacity has almost doubled. This has resulted in modifications, many of which have affected zinc deposition operating conditions in the cells. Some of these changes appeared to have affected average current efficiency to such an extent that a special investigation was initiated, using multiple regression analysis to assess historic cell unit operating para- meters. The study highlighted the importance of certain parameters in maintaining maximum current efficiency for zinc deposition from !Risdon purified solutions under conditions of !changing current density, acidity and zinc con- centrations. Maximum current efficiency was obtained only within a zinc to acid ratio in cell electrolyte of 0.45 - 0.55 and a residual zinc concentration greater than 48 g.1-1, irrespective of actual zinc concentration or The investigation also established: ieters giving minimum power consumption at termined current density; the effect of ntration changes in common impurities on nt efficiency; the existence of high s of some impurities in solids precipit- in the cells and pure solution tanks.

Jan 1, 1975

By C M. Ramotsabi, F Bornman, W Erasmus

Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and heavy mineral ores (Wills, 1992). Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating many minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid such as water or air (Wills, 2006).The main operating variables for a spiral concentrator are the feed rate, the slurry concentration, the wash water addition and the position of the splitters used to separate the tailings, middlings and concentrate streams (Sadeghi, Bazin and Renaud, 2014). Wash water is an important control variable used to wash away entrapped light minerals from the concentrate stream (Burt, 1984; Bouchard, 2001). Sadeghi et al concluded the spiral operation to be sensitive to the wash water flow addition and resultant economic trade-off. Increasing the wash water flow rate increases the concentrate grade at the expense of the iron recovery.The paper addresses the effects of dripping wash water onto the concentrate stream of a spiral processing fine iron ore. The dripping wash water system offers a low flow alternative and could possibly provide a good balance between grade and recovery of valuable minerals without using excessive water. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentrations; the wash water rate and the splitter positions were kept constant.The use of wash water at 30 per cent, 35 per cent and 40 per cent solid concentration improved the Fe grade in the concentrate by about 1.5 per cent, six per cent and eight per cent respectively. The additional SiO2 rejected by the wash water is approximately three per cent, nine per cent, and 11 per cent at 30 per cent, 35 per cent and 40 per cent solid concentration respectively. Addition of wash water is shown to have minimum effect on grade at 30 per cent solid concentration, and Fe upgrades obtained with and without wash water were found to be similar. Notable upgrades were observed at 35 and 40 per cent solid concentration with wash water. The results obtained suggest that the additional SiO2 rejection by wash water increases with an increase in solid concentration. This suggests that the benefit of using the drip system is notable at higher solid concentration. It is believed that at lower solid concentration SiO2 particles are reasonably free to move around and are possibly less entrapped than at high solid concentration.The Fe grade/recovery and solid concentration relationship with wash water showed a non-linear correlation. The Fe grade increases with an increase in solid concentration up to a somewhat optimum point and then drops as solid concentration increases further. The recovery of Fe on the other hand follows a converse relationship with solid concentration, the recovery decreases from 30 per cent to 35 per cent solid concentration and then increases again at 40 per cent solid concentration. The increase in recovery at higher solid concentration could possibly be explained by the fact that the mass yield to concentrate also increases with solid concentration. Since recovery is a function of both grade and mass yield, the higher recovery at 40 per cent solid concentration is likely due to the high mass yield obtainable at 40 per cent solid concentration.The drip system could therefore possibly offer a safe guarding against grade and solid concentration variations without using excessive water, and possibly ensure that a product within specification is maintained.CITATION:Ramotsabi, C M, Erasmus, W and Bornman, F, 2015. Optimisation of wash water on an iron ore spiral to improve grade, in Proceedings Iron Ore 2015, pp 175–184 (The Australasian Institute of Mining and Metallurgy: Me

Jul 13, 2015

By T Baumgartl, D R. Mulligan, D Doley, A Schneider

In arid and semi-arid areas evapotranspiration (ET) cover systems are often used to mitigate contaminated seepage from hazardous mine waste into the adjacent environment. The theory of ET covers is based on the water balance equation with the aim of minimising seepage. While cover systems are commonly trialled, the influences of variability in climate and cover structure on water balance equation parameters are seldom investigated.Water balance equation parameters and their variability were analysed for two ET cover trials constructed from benign waste rock in semi-arid Australia. Seasonal and inter-annual variations in rainfall critically influence cover performance. For successful cover system operation, the average return periods for higher than average rainfall should be taken into account. In addition, failure of ET covers has a higher probability in areas with marked rainfall seasonality. Water holding capacity and plant available water content are low in covers constructed from waste rock. Changes in water holding capacity due to variation in particle size distribution are likely and critically influence cover performance. The application of topsoil can be beneficial for water ingress control through run-off, but a balance has to be struck between run-off, erosion and plant available water. Changes in vegetation composition only influence evapotranspiration water losses at plant coverage exceeding 50 per cent, which is unrealistic in semi-arid areas. This study showed that the capacity of ET cover systems to hold and dispose of received rainfall is often lower than assumed by industry practitioners. Furthermore, in order to improve reliability of long term cover performance, the variability of rainfall and water holding capacity of the cover has to be included in water balance models.CITATION:Schneider, A, Baumgartl, T, Doley, D and Mulligan, D R, 2012. Variability in parameters of the water balance equation and their influence on evapotranspiration cover performance, in Proceedings Life-of-Mine 2012 , pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By J Missen, P Currie, J Bohan, D Clark

AGL is one of Australia’s leading integrated energy companies and the largest ASX listed owner, operator and developer of renewable energy and thermal generation in the country. AGL owns and operates the 2210 MW Loy Yang A power station and adjacent 30 Mt/a brown coalmine in the Latrobe Valley, Victoria. It also supplies coal to the nearby 1050 MW Loy Yang B power station owned by the GDF Suez (Engie)/Mitsui partnership. The mine is currently nearly 5 km long, more than 2 km wide at the operating face and up to 200 m deep. AGL employs a large workforce at Loy Yang and a substantial amount of services are performed on-site by contractors and consultants.GHD provides mine planning, earth sciences, civil/geotechnical engineering, dam surveillance, plant engineering and environmental services to AGL Loy Yang through an alliance framework. GHD is one of the world’s leading professional services companies operating in the global markets of water; energy and resources; environment; property and buildings; and transportation. In addition to GHD’s global footprint, the company also has a significant Victorian presence, including a permanent, well-resourced regional office in Traralgon, approximately 10 km from Loy Yang, as well as a permanent site office.A joint paper on the Loy Yang mine professional services alliance model was written for the AusIMM International Mine Management Conference in 2006 by Woods and Wood. Now ten years on, this paper provides an overview of the present relationship and arrangements, including the continued transformation of the alliance model and maturing of the relationship contract.These are challenging times, with increasing cost and regulatory pressure driving change in the broader energy and resources industry, and locally including both the mining and power sectors at Loy Yang. Flexible models to achieve a balance between internal personnel and access to key external skills, whilst achieving value for money and transparency, is increasingly critical. The right drivers and performance measures are essential, particularly when confronted with potential major technical and environmental risks (considering significant ground failure and fire events that have occurred elsewhere within the Latrobe Valley over the last decade) within a sector that is reducing costs and optimising production.This case study discusses the alliance status and changes, reasons behind adjustments and what the future is likely to hold. The paper also explores the validity of the original objectives and the extent to which they have been achieved. The philosophy of the alliance is to continue closely aligning the objectives of the two companies in the best interests of the Loy Yang site and immediate surrounds/stakeholders. Quality of service, costs, timeliness, health and safety (H&S) and some operational activities (aquifer depressurisation) remain important aspects and are reflected in key indicators for which performance is measured.CITATION:Clark, D, Bohan, J, Currie, P and Missen, J, 2016. AGL energy, Loy Yang and GHD – a further case study in alliancing: ten years on, in Proceedings International Mine Management Conference, pp 321-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Metana Minerals commenced life in 1970 and graduated to a mining company in 1981 with the opening of a small alluvial tin-tantalite mine at Wodgina (W.A.) The present board of directors assumed control of the company in 1978 and established the exploration and development philosophies that have guided the company's expansion to its present status as an emerging diversified miner. An ability and willingness to raise equity capital when required has been a feature of the company. Company activities include exploration for gold, diamonds, heavy mineral sands, polymetallic (base and precious metals) deposits, strategic minerals, rare earths, oil and gas in a geographical distribution covering the entire Australian mainland Metana owns and/or operates four gold mines (Reedy, Mt Magnet, Youanmi and Howley) and at the time of writing is developing a fifth gold mine - its first underground mine - at Rothsay. In contrast to many similar or larger sized companies, Metana undertakes most activities itself rather than through the use of consultants or contractors. In-house services include: analytical and metallurgical laboratories, plant engineering design and construction, drilling and mining (earthmoving) Metana Minerals has established an enviable reputation for technical excellence and this expertise has placed the company in a sound position to continue its growth pattern into the future. This growth will be achieved through a combination of low cost and successful exploration and acquisition of suitable mines either directly or through corporate activity.

Jan 1, 1989

By R Dunne, G Lane, S Ha, D Dreisinger

The paper outlines the 17 Mt/a Telfer Project plant process design from sample selection to feasibility study design. The 366 Mt Telfer mine reserve consists of a diverse range of copper and gold mineralisation, from massive sulfide reef ores to stockwork ore, oxide copper minerals to chalcopyrite, siltstone to competent quartzite, all with relatively high levels of gravity recoverable gold. The complexity of the orebody demanded a flexible plant that could recover copper and gold values by a combination of gravity recovery, flotation and concentrate leaching. The demands of treating ore from a high grade underground mine and a variable grade open pit (that includes underground old mine workings) necessitated a dual train approach from primary crushing to concentrate production in order to minimise the requirement for campaigning of different ore types. An extensive sampling, testwork and technical evaluation program was undertaken to identify processing characteristics and the optimum process route for each ore type. The design experience included: the development of robust primary stockpiling and pebble crushing concepts; detailed review of scale-up of SAG and ball mill pilot plant data to plant scale; the selection of two 15 MW SAG mills and two 13 MW ball mills for the grinding circuit; and detailed modelling of the pyrite concentrate carbon-in-leach (CIL)/sulfidisation acidification recovery thickening (SART)/acidification volatilisation recovery (AVR) process to optimise design for copper and cyanide recovery from leach liquors. The Telfer plant design also measures the development of process design based on experiences at the Cadia Hill Cu/Au concentrator, commissioned in 1998. The differences between the two plants are compared and contrasted.

Jan 1, 2003

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

By G B. Arehart, S J. Mathews, J L. Mauk

The banded nature of the quartz veins which form the Empire lode at the Golden Cross mine, is perhaps their most striking feature. Petrographic studies show that significant differences occur between the bands in terms of textures, quartz grain size, calcite, adularia and kaolinite content, and the form, concentration and mineralogy of sulfide phases.   The d18Oquartz values of individual bands within the vein material range from 7.3-10.9ë. Calculations show that the d18Oquartz values can be adequately explained by temporal variations in the system temperature, boiling and/or variations in the systems fluid/rock ratios.

Jan 1, 1995

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

By D Timms

The Kempfield deposit is located in the Hill End Trough, one of several intracratonic basins developed during Silurian–Devonian time, in the eastern province of the Lachlan Orogen, Eastern Australia.The deposit contains an oxide resource of 5.8 Mt @ 58 g/t Ag and a sulfide resource of 14.4 Mt @ 45 g/t Ag, 1.7 per cent Zn and 0.6 per cent Pb, classified and reported in compliance with the JORC Code. The deposit has been previously explored by a number of companies, including INCO, Shell, Jones Mining, Golden Cross Resources and recently Argent Minerals Ltd (Argent). Argent is currently completing a definitive feasibility study with a view to mining the deposit.The deposit is hosted at the boundary between the Molong High to the west, comprising Ordovician sediments and volcanic rocks and the Hill End Trough to the east, interpreted as a back-arc basin containing Silurian sediments and siliceous-feldspathic volcanic rocks. The boundary between these two strato tectonic units is an imbricate thrust fault zone known as the Copperhannia Thrust.The Kempfield deposit is hosted in felsic volcanic rocks known as the Kangaloolah Volcanics. These have been in-faulted and folded into the Middle Ordovician meta-sediments of the Coombing Formation of metasediments along the Copperhannia Thrust. The Kangaloolah Volcanics belong to the Late Silurian Mumbil Group, comprising submarine carbonate-shale facies interspersed with extensive felsic volcanic piles, which grade conformably upwards into turbiditic sandstone and siltstone sequences (interpreted to represent a deeper depositional environment). These turbiditic rocks are known as the Campbells Formation, comprising siltstone, sandstone and andesitic tuff. The rocks at Kempfield are metamorphosed to lower greenschist facies, reflected through the different type of schists.Silver, gold, lead, zinc mineralisation is hosted in barite-rich horizons, near the boundary to quartz-phyric tuffaceous rocks in submarine, immature, reworked felsic ash tuffs. Barite appears to be hosted in greatest concentrations by the coarser grained volcanoclastic sandstones and grits, whilst intercalated siltstones are volumetrically minor and tend to return low barite and silver. Mineralisation is hosted in stratiform and probably stratabound barite-rich horizons. A northeast-trending, steeply dipping, metamorphic cleavage (S1) occurs throughout the project area.

Aug 22, 2011

By Nicol S. K, Swanson A. R

The poor flotation response of many coals has in the past been attributed to such factors as differences in rank, differences in degree of oxidation, differences in petrographic composition, or slime coatings. The present work shows that while all these factors undoubtedly influence flotation, the size distribution of the feed may override these. Evidence is presented which shows how this factor can lead to substantial losses of coarse coal (>250 µm)from a coal which would normally be considered amenable to flotation. Reasons for this loss of flotation response are suggested together with means of overcoming the problem.

Jan 1, 1978

In New York City, on the walls of the library of the United Engineering Societies are these words:"Engineering-the art of organising and directing men and of controlling the forces and materials of nature for the benefit of the human race," but who, reading the schedules of even our best engineering schools, would infer that engineering is an art or that it should always havejn mind the benefit of the human race? While it must be remembered that our engineering schools exemplify the British cult of the amateur, that cult which lets men who have never attended a lecture on "Education" or perhaps nevereven read a book on it, become enginering teachers by profession (and so educators by inference), the root of the matter is to be found in the fact that our educational aims, and consequently our educational practice, seem suited much better to the position engineering held in the community in 1900 than to the position it holds to-day. This civilization of ours has developed, !;loth for good and for ill, into one based largely on engineering achievement; technical progress is so continuous and so rapid that thevalue of descriptive knowledge of current practice is ever lessening; enough must be imparted to make the young graduate immediately employable, and this amount is sufficient for illustrating the principles on which practice is based and on which its advance depends, but the young graduate's technical progress depends much less on his having acquired additional knowledge than on his ability to acquire knowledge, so, paradoxically, the more useful knowledge there is availabJe the less of it the student should be taught.Less conspicuous but fully as important is the enlargement of the field of work of engineering graduates, especially its extension to the initiating of policies and to the broader problems of administration. At present the road to such positions lies normally through a considerable period of professional work, but it is by no means unlikely that the field will soon include much that requires little professional expel'ience. At all events it is safe to say that the changed. and changing position of engineering in the communitydemands the attention of the engineering schools and that profitable discussion of engineering education demands some understanding of the real nature of education and of the part which engineering plays in the life of the community.THE NATURE OF EDUCATIONUnfortunately "to educate" supplies an example of how words degenerate in meaning; most people regard it as the equivalent of "to instruct"; a small number feel they have gone to. the root of the matter when they say...

Jan 1, 1941

The ultraviolet spectrum of isopropyl ethylthionocarbamate (the principal constituent of Dow flotation collector Z-200) in water and of Z-200 itself in water was found to have an absorption peak at 242 nanometers(nm). The height of this peak was found to be directly proportional to isopropyl ethylthionocarbamate concentrations up to 15 p.p.m. Z-200 contains about 90 per cent isopropyl ethylthionocarbamate and the heightof the peak was proportionately lower, but obeyed the straight line relationship up to 15 p.p.m. This showed the potential value of spectrophotometric measurements for the determination of Z-200 residuals in flotation liquors.Methyl ethyldithiocarbamate (an impurity in Z-200) increased the peak height slightly, but other impurities in Z-200, xanthates, and most inorganic salts present in flotation liquors do not interfere. However nitrate ion and thiosulphate ion have absorption peaks which overlap the isopropyl ethylthionocarbamate peak.The simplest general method to overcome this effect is to extract the isopropyl ethylthionocarbamate into cyclohexane and to measure the absorbance of the extract.The maximum absorbance of the cydohexane extract was at 247 nm and the peak height at this wavelength was found to be directly proportional to the isopropyl ethylthionocarbamate or Z-200 concentration in the original aqueous solution. An alternative method is to measure the spectrum of the original aqueous solution using the aqueous raffinate from extraction as a reference solution. This gives the spectrum due to isopropyl ethylthionocarbamate alone and measurement of the absorbance at 242 nm gives the concentration in the original aqueous solution. Both methods give the same value for the concentration of isopropyl ethylthionocarbamate in the original solution.

Jan 1, 1969

On the more important mines it is almost essential to have a general plan of the surface. A special feature of this plan should be the indication thereon of a suitable arrangement of contour lines, either wholly over the surface of the property or at parts where may seem most useful. The importance of having these contours marked on the plan will be best appreciated by the engineer, in selecting the best available site for a proposed new plant, in locating a tramway, in connecting the surface with the underground workings to the best advantage, or in solving many similar problems that come within his province. The closer the contours are together vertically the better, the limitation being the trouble and expense of getting them on to the plan. They may range from five to fifty feet apart but a distance of ten feet will be found, in most cases, to be the most useful.In deciding the datum level from which these contours are to be measured, it is best to depart from the ordinary sea level datum, and use instead the highest available point on the property. This datum will be called zero and all levels will be reckoned so many feet below it; thus by a contour marked 160 on the plan, it will be understood that the level of the plane of the contour is 160 feet below the highest available point on the property. This system of measuring levels downward is readily suggested from measuring the depths of shafts from the brace or of excavations from the original surface.

According to the data provided by the most recent European Survey on Working Conditions, roughly 25 per cent of the European working population is exposed to mechanical vibrations for no less than one quarter of the work shift duration, while around ten per cent are exposed for the entire work shift. The occupational exposure to whole-body vibration (WBV), in particular, represents a major health risk in mining, quarrying and civil excavation activities. In accordance with European Directive 2002/44/EC, the latest version of the Italian law on physical risks has recently confirmed the possibility of using relevant literature data on vibration magnitude in order to evaluate personal occupational exposure (vibration database or data provided by the manufacturer). Still the alternative option, based on field measurements, represents the most appropriated method of risk assessment, as it accounts for the actual operating condition at the workplace; actual operator and vehicle under investigation and specific working cycle. The article discusses the vibration measurements taken on a number of heavy machinery (excavators, loaders, trucks, dumpers, etc) employed for talc extraction in a mine located in Sardinia and the resulting personal exposure for the drivers. The assessment was carried out in accordance with the specifications of ISO 2631-1 and EN 14253.

Dec 6, 2010

The Inglewood Gold Project consists of several titles in and around the Inglewood and Wedderburn Goldfields which were purchased from Strata Mining Corporation (now Excalibur Mining Corporation). The Inglewood goldfield has a historical production of approximately 160 000 tonnes at 23 grams per tonne. The company has reopened and developed the Maxwells reef, picking up a high-grade shoot (Max Shoot) identified and worked by Goldquest et al up until 1994. Production ceased on a low gold price, rapidly reducing vein size and a requirement for further development. Greater Bendigo Gold Mines Ltd (GBM) has undertaken the development and encountered the mineralised vein in an increasing size setting with high grades and the existing mine development has access to a further shoot to the north (Max North Shoot). The Maxwells reef also contains the Woolf shoot south of the Maxwells shaft and an inferred resource of ~20 000 ounces is contained from 60 m below surface. Best intersection 2.9 m at 50 g/t. The Maxwells reef area produced approximately 20 per cent of the Inglewood goldfields production and GBM is preparing to increase its exploration efforts across the rest of the field. A processing plant has been constructed at the Maxwells mine site, which is capable of treating tailings, hard rock and alluvial material utilising gravity recovery. The existing Maxwells tailings have been excavated and treatment commenced. It is intended to produce a sand product from the tailings for resale and to reduce the storage requirements per tonne. Several large water dams constructed by Goldquest in the 1990s are being re-engineered to enable storage of significant tonnages of tailings. A level of surface and underground production is planned for 2008 and this is to be expanded into 2009 and beyond. The long-term future at Inglewood is envisaged as structural repeats at depth below the current workings and a project plan to gain deep access will be prepared on successful drilling results.

Jan 1, 2008

This paper is essentially an address, rather than a detailed presentation of facts, because the third edition of `Nuclear Electricity - An Australian Perspective' has just been completed and will be available for the seminar. That 96-page booklet contains a lot more information than The AusIMM would be prepared to print in the seminar proceedings. Hence I have kept this paper brief, and ask readers to obtain a (free) copy of Nuclear Electricity at the seminar or from The AusIMM. It can be read as a supplement to the paper (or vice versa). According to one of Australia's well known critics of nuclear power, Professor Ian Lowe, `the pro-nuclear lobby's predictions of the future use of nuclear energy .... have been regularly and consistently wrong by large amounts, always overestimating the future demand for uranium" (Aust. Society, April 1989). While I do not accept this as a bald statement applying to all those in favour of increased use of nuclear power, there is sufficient truth in it for it to be credible. Certainly in the 1950s and the 1960s, when the new technology for producing controlled power from atomic fission was first being commercialised, there were some very exaggerated projections of the role of nuclear power. Many people thought that it would take over from fossil fuel fired electricity generation in much the same way as the motor vehicle took over from horse-drawn transport. And these early projections were not simply concerned with electric power generation, they included excavating harbours and digging canals with nuclear explosives.

Jan 1, 1989

By A Simmons, J Chan, A Li, Q Gu, D M. Brett

The paper presents an example of field density achievements using thin layer deposition and solar drying and compares this with compaction data from laboratory testing and field trials of mechanical densification processes.

Jul 1, 2021

By T Hughes

Upward pressure on all mining operations is coming from the triple bottom line. To some extent this is being offset by the rise in mineral prices, but this may or may not continue. The other serious issue facing all companies is the replacement of economic reserves as exploration levels over the past decade continued to decline in line with falling mineral prices. In order to underpin the sustainability of the mining industry it is necessary to continue to reduce cost, reduce the mine environmental footprint, whilst increasing community benefit. At the same time it is imperative that we increase the economic reserves. The highest risk is in adding new mineral discoveries as the strike rate for economic discovery decreases. Gekko Systems Pty Ltd recognises that the most simple and risk averse route to increasing economic reserves is to reduce cut-off grade in the mine, thereby bringing formerly uneconomic reserves into the economic category. We have been developing a new process flow sheet which embodies the triple bottom line and the issue of economic replacement of reserves. This paper describes this flow sheet and presents four examples where this concept is/can be applied to bring about triple bottom line benefits. Sustainability can only be assured if we are the ones in control of our environment, costs and reserves.

Jan 1, 2007