Search Documents

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

Flotation Research on Cassiterite of Tailings

Sep 13, 2010

By D R Quick

The Goodall gold mine is located 30 km east of Adelaide River, within the Pine Creek 1:250 000 map sheet, at 8 525 000 mN: 750 000 mE, on the AMG grid. The first gold was poured in April 1988 and the mine closed in September 1993, having produced 228 400 ounces of gold from 4.095 million tons of ore, at a head grade of 1.99 g/t. Oxide and primary ore was mined from one large open cut and low grade oxide ore from three smaller pits. The gold mineralisation was discovered in 1981 by means of a helicopter borne rock chip sampling survey, which delineated 13 discrete anomalies. Systematic grid sampling of rock chips outlined an area of 1300 m by 300 m within the 2.0 g/t contour. Over 7500 m of costeaning was used to delineate the A and B-Pod mineralised areas. Geochemical soil sampling played only a minor role in the discovery and geophysics none at all. By the end of 1984, 40 diamond drill holes had been completed and a resource of 3.63 million tonnes at 3.0 g/t calculated. In January 1985, Western Mining Corporation Ltd became a joint venture partner and funded exploration to cam a 60 per cent interest. Additional drilling led to a feasibility study in 1987, based on a Measured and Indicated resource of 4.25 million tonnes at a grade of 2.35 g/t. The host rocks are quartzo-feldspathic wacke and interbedded phyllitic siltstone, of the Proterozoic Burrell Creek formation. The main zone of gold mineralisation, A-Pod, occurs in a sub-vertical vein array, up to 50 m wide and 800 m in length, of quartz and sulphide veins (5-20 mm wide), It is parallel to and on the east limb of an upright, north plunging anticline. Five types of veining have been recognised, with the bulk of the gold mineralisation associated with quartz-pyrite-arsenopyrite and chlorite-quartz-pyrite veins. The gold occurs as particles, from 1-20 micron, as inclusions and along fractures in pyrite and arsenopyrite and to a limited extent in chlorite. The mineralisation is epigenetic and structurally controlled by fractures developed during an earlier folding event. The gold is assumed to have been derived from the underlying sediments of the Koolpin Formation by hydrothermal fluids emanating from the deep seated northern margin of the Cullen Batholith. Precipitation of gold may have been controlled by variations in temperature and pressure.

Jan 1, 1994

By K Ionkov

The oolitic iron ore reserves in Lisakovsky, North Kazakhstan represent quite a challenging deposit both from a technological and from a resource point of view. The difficulties in processing such types of ore are connected with the extremely fine dissemination of phosphorus and gangue minerals inside the oolitic formations. The goethite crystals are cemented in their structure by aluminosilicates with quartz and other gangue minerals and dissemination is so fine that they are not separable by physical methods. The laboratory tests performed for dephosphorisation show that the combination of alkaline roasting followed by low intensity magnetic separation and acid leaching enables the obtaining of high grade iron concentrate. The magnetic separation performed ahead of leaching is effi cient as a means of buffering the high pH by washing out the soluble salts and the excess of base and after leaching facilitates the removal of secondary liberated gangue minerals in the non-magnetic fraction. As a consequence, phosphorous content is dropped to a more acceptable level for the ferrous metallurgy and iron grade and recovery reach 61.6 and 80.8 per cent respectively.

Jul 11, 2011

By E Apaza, R Neumayr

This paper aims to summarise the discovery of the QTS Central resource, a previously unidentified +1 Mt inferred resource that lies between two major CSA resource systems.The 1.7 Mt at 5.76 per cent Cu, QTS Central ore system represents 1/6th of the CSA mineral resource and was discovered in 2014 based on the accumulation of historic exploration records dating back to 1989.The CSA deposit consists of five ore systems hosted within turbidite-derived siltstones (CSA Siltstone) and lesser sandstones (five per cent) of the Devonian Amphitheatre Group. The host sediments strike approximately north–south with a steep westerly dip and exhibit a well-developed east dipping cleavage. Most CSA mineralisation is hosted within dilation zones at the intersection of cross-cutting structures and is interpreted as epigenetic in origin.Alteration and weak mineralisation, up plunge to the reported QTS Central mineral resource, was initially detected in 1990 during a downhole electromagnetic conductivity (EM) study, where one hole indicated an off-hole conductor, later tested with four diamond holes. One of these diamond holes intersected 3 m at 7.5 per cent Cu at 200 m. Development of the 9070 Subway drive in 2005/2006, linked the QTS North and QTS South workings and intersected structures interpreted to host QTS Central mineralisation. Subsequent drilling proximal to the 9070 Subway in 2007 identified an up plunge extension to the QTS Central zone (UDD07152: 1.8 m at 6.3 per cent Cu from 10.7 m). Work on QTS Central was largely forgotten until 2012 when the mining of a 450 m infrastructure drive provided a platform to test the anomalous grades. In December 2013, drill hole UDD13055A intersected 20.9 m at 7.2 per cent Cu from 378 m. By the end of 2014, the QTS Central inferred resource was 1.0 Mt at 6 per cent Cu and 18 g/t Ag (Hosken and Apaza, 2014). Late in 2016, further infill drilling occurred from two fronts to increase confidence in the QTS Central resource. The results of this drilling are expected late in 2017.The current interpretation indicates the QTS Central system consists of two main lenses hosted within closely bedded sandstones and siltstones. The sandstone in general is not mineralised, being heavily silicified, while the siltstone is mineralised and chloritised. The main mineralised lens is 75–200 m along strike and 450 m high. Massive sulfide feeder structures lie at the core of the two main lenses, although the characteristics of the QTS Central system tend toward the mineralisation being more chlorite-rich than in QTS North and QTS South.CITATION:Apaza, E and Neumayr, R, 2017. The discovery of the QTS Central ore system, CSA mine, Cobar, NSW, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 151–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

The object of this talk is to bring before members the importance of the prospector and the' State Battery system to the wealth and prosperity of the mining industry in particular and the State of Western Australia in general, and to touch on the more important features.Customs plants of any sort are usually subject to a good deal of critioism, usually on the large profits made at the expense of the customer, etc., and this often clouds the real value of the work being done.Prospectors, on the whole, are a good class of men; they work under conditions and difficulties which would deter those less spirited. Food, water and mining supplies are often difficult to obtain and frequently have to be transported great distances. Their mining tools are usually of the most primitive type, yet during last year over 109,000 tons of prospectors' ore were handled by the State Battery system for 73,250 fine oz. valued in Australian currency at over £587,000, the value being 57/- per long ton at par.This production brings the State Battery system into fourth position amongst the producers of the State, the yield being exceeded by the Lake View and Star, Wiluna and the Great Boulder.In passing I might mention that these notes were written at the end of the year 1940, and the above figures were for the previous period. The figures for last year, 1940, were not quite so good, being 101,000 tons for approximately 60,000 fine oz., valued in Australian currency at £572,000.In spite of this drop the State Battery system maintained its position as fourth in order of gold output for the State.The extractions, as a whole, throughout the system, were 92·54%, made up of 68·86% by amalgamation and 23·68% by cyanidation. These figures, for a group of 20 plants treating widely different classes of ore, must be considered satisfactory. The total production since inception is over £11,000,000 in Australian currency.State Batteries are usually more or less of a standard design. Ore is reduced to about 2i in. maximum size before being sent to the bins. Challenge automatic feeeders control the feed to each mill unit, amalgamated copper plates collect the free gold. Corduroy strakes are used with some ores after amalgamation, but in only a few cases has this been found of any advantage to the customer.The pulp from the battery is sampled, after leaving the tables, with a "Tazewell" sampler and pumped to dams for subsequent cyanide treatment.The "Tazewell" sampler is a machine driven by the moving pulp; and takes about fifteen dips per .minute from such pulp through a slotted...

Jan 1, 1941

By J Seccatore, F Golin, E Munaretti, M Cardu, J C. Koppe, J Bettencourt

Contour blasting is commonly performed by employing linear charges decoupled from the boreholes. This method is common in surface and underground excavations, either for civil or mining purposes. To achieve the best results in terms of rock breakage and respect of the excavation profile, blasting theory suggests that charges should be inserted coaxial to the holes to grant uniform distribution of the explosive energy, therefore obtaining a uniform radius of damage. Nonetheless, due to readiness of operations or lack of availability of specific products on the market, non-coaxial charges are often employed in blasting practice. Non-coaxial charging methods include the employ of high-power detonating cord (40 to 100 g/m), low-power detonating cord connecting small-diameter cartridges (commonly 10 g/m detonating cord priming 1” cartridges) or string loading (a thin layer of bulk emulsion pumped with controlled flow and controlled extraction of the injecting rod). This research focuses on evaluating the effects of the first two charging methods on the quality of final walls in open pit and underground operations. Different drilling geometries and charging configurations were applied to both quarrying and tunnelling blasts. The half-cast factor, the overbreak and the underbreak were evaluated as control indicators. Rock quality designation and rock mass rating were used to classify the rock mass. The research was aimed to push contour blasts to their limits, observing for which geometry and charge configuration the blast lost its design threshold with respect to the final wall for every given rock mass. Results show the operational limits of non-coaxial charges encountered in the rock masses object of this study. In good-quality rock, smooth blasting with decoupled linear charge of 40 g/m can be extended to a spacing S = 22Øf with little or no detectable drawbacks in terms of final wall quality, in contrast with theoretical formulae for the determination of the radius of damage. On the other hand, when the rock is poor, any quality of the final wall is hardly achieved at all, in spite of any care in the details of execution of smooth blasting. It is concluded that any design criterion and theoretical approach modelling the effects of contour blasting cannot ignore the features of the rock mass.CITATION:Seccatore, J, Golin, F, Cardu, M, Munaretti, E, Bettencourt, J and Koppe, J C, 2015. Evaluating the effects of non-coaxial charges for contour blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 267–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Technologies are receiving a lot of 'press' - and rightly so; as they are seen as the means for achieving quantum leaps in productivity and cost reductions. A point of concern for Caterpillar is that we do not believe there is enough understanding of the infrastructure needed to support some of the future technologies, as well there is not enough utilisation of the current systems.

Jan 1, 1997

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995

A field method combining solvent extraction and paper partition chromatography permits a simple and rapid semiquantitative estimation of gold in siliceous, argillaceous and sulphide ores. The method will facilitate the eyaluation of prospect samples in which the gold is too fine for separation by panning.Ethyl alcohol-hydrobromic acid mixtures are suitable for chromatographic development of the gold complex, and give clear reproducible definition of the gold zone. Substitution of commercial "methylated spirits" for the ethyl alcohol gives equally good definition, improving the potential of the method for field use.A batch of six samples in the range of 0·5 to 5·0 dwt/ton can be completed in two hours. The range may be extended by simple modification to higher or lower values.INTRODUCTIONIn a chromatographic method described previously (Lever 1958, Nevill and Lever 1959), gold from a standard volume of ore clamped between -plate glass was extracted by aqua regia on to the paper. After cautious drying the chromatogram was developed by an ethyl acetate-nitric acid-water mixture and gold was identified by spraying with stannous chloride solution. Sensitivity of the method in the low range was poor. The brown line obtained in the 1-3 dw/j ton range, caused by movement of gold in the reduced form, was not considered to be a satisfactory confirmation of the presence of gold. It was felt that the method would be improved by using a more elegant extraction and applying developing conditions which would produce a well defined purple line at all gold values. Iron was a limiting factor, and a method of eliminating its interference was needed.The method now developed overcomes these shortcomings, and gives a reliable result with a purple line for assay values of 0·5 dwtjton and over. Gold is dissolved from an...

Jan 1, 1964

By Burns W. G, Muceniekas E, Whitcher I. G, Hughes F. E

No iron ore deposits were reported before 1961 from the Hamersley Ranges, Western Australia, although low-grade bedded iron formations, associated with ferruginous jaspers and cherts, were known to occur in the local Nullagine Series of Precambrian age.In January-March 1961 preliminary investigations in the area drained by the Turner River, Duck Creek and Serpentine Creek revealed the presence of over 1000 million tons of dense botryoidal or pisolitic limonite, forming flat-lying orebodies with 50-57 per cent iron.Large bedded hematitic orebodies were also discovered in the same area in August-October 1961. These have a porous, biscuity texture and an iron content of 60-61 per cent. They occur at a welldefined stratigraphic level (Brockman Iron Formation), normally in synclines where they have been upgraded by circulating meteoric waters during an old cycle erosion.In 1962 systematic geological studies and mapping, together with sampling and scout drilling, indicated larger reserves of biscuity hematitic ore and led to the discovery of massive hematite deposits at Mt. Tom Price. These were extensively drilled in 1963, proving the persistence of' high-grade mineralisation to a depth of 200 ft and over.To date the total indicated reserves of the Hamersley deposits, within the area held by Hamersley Iron Pty. Limited, are of the order of 4960 million tons and thus rank among the more important of the world. The reserves are composed of 600 million tons of bedded dense hematite ore with 64-66 per cent iron, 2900 million tons of bedded biscuity hematite-limonite with 60-61 per cent iron, 1360 million tons of limonite (goethite) ranging in grade from 50 to 57 per cent, and 100 million tons of canga (conglomerate) iron ore containing 53-63 per cent iron. In all cases harmful impurities are comparatively low.

Jan 1, 1964

Winzes are usually sunk 9 ft. 6 in. long by 6 ft. 0 in. wide and are divided into two compartments, 4 ft. 0 in. by 5 ft. 0 in. inside the timbers. The general practice is to sink the winze to a depth of from 9 to 12 ft., put in bearers and three or four rings of timber, and then erect a sinking headframe before continuing sinking operations.GENERALThe main feature governing the design of the headframe was that all parts could be transported on timber trolleys in No. 2 Shaft. Except for some minor details the structural members consist of steam pipe. Joints are sections of steam pipe welded to one member and into which the other member fits and is held in place by a 1-in. bolt. The headframe consists essentially of two bedpieces to carry the winch and to form a seat for the four legs. The legs support the sheave bearers, the tipping door and the brace.Except during tipping operations the door is in a nearly vertical position. For tipping it is lowered to an inclined position and a hook suspended from one of the bracing members of the headframe is attached to a "D" welded to the bottom of the kibble. This causes the kibble to tip when it is lowered on to the tipping door. The capacity of the kibble is 4 cubic feet.THE HEADFRAMEThe dimensions of the headframe are:Height to top of sheave .. .. 14 ft. 10 in.Distance centre to centre of legs 4 ft. 4 in.Length of bedpieces .. .. .. .. 8 ft. 9 in.The weight is approximately 2,000 lb., the tipping door and bedpieces being the heaviest members. They weigh 240 lb. and 170 lb. respectively.One compartment of the winze is decked over, and the bedpieces, which are 8 ft. 9 in. lengths of 6 in. pipe with three short lengths of plate welded to the underside, are placed over the sinking compartment, either transversely or parallel to the winze. Three 3 inch pipes act as spreaders between them.Welded to the top of each bedpiece is a 6-in. by iHn. plate 3 ft. 0 in. long with four 4-in. by 1.5-in. slots cut longitudinally at 10 in. centres. Two 10 in. by 4-in. timbers are bolted to these plates, the distance between them being adjusted to suit the holes in the winch bedplate, which is bolted to the 10-in. by 4-in. timbers.Two short lengths of 3 in. pipe are welded to each bedpiece at 4 ft. 4 in. centres. These form the seats for the legs of the headframe, which are...

Jan 1, 1941

Development of the Boleo Process Flow Sheet and the Direct Solvent Extraction (DSX) Circuit for Cobalt and Zinc Recovery The metallurgical process designed to treat the El Boleo Cu-Co-Zn-Mn ore involves a sulphuric acid leach in seawater under oxidative and then reductive conditions to maximise metal extraction. Copper and cobalt are recovered as cathodes by electrowinning, zinc and manganese as zinc sulphate monohydrate and high quality manganese carbonate, respectively, by precipitation after a number of separation and purification stages. One of the key purification stages of the Boleo metallurgical process is the CSIRO DSX circuit. The DSX circuit was developed using the synergistic solvent extraction (SSX) technology. Initially, a synthetic solution was studied, and by adding 0.4 M LIX63 to 0.5 M Versatic 10 in Shellsol D70, large synergistic shifts were obtained for cobalt (?pH50 4.24) and zinc (?pH50 1.62). After a single contact, the separation factor of metals over manganese reached over 6,000 for cobalt and over 380 for zinc, indicating excellent separation of cobalt and good separation of zinc from manganese, magnesium and calcium. The SSX system was further optimised with the modified synthetic pilot plant solution. The extraction of cobalt and Zn after a single contact was 93 per cent and 70 per cent, respectively, while the Mn concentration in the loaded organic solution was only 0.28 g/L. A proof of principle pilot plant operation was conducted in 2004 and a demonstration pilot plant for final engineering design in 2006 with outstanding performance of the DSX circuit. For the demonstration pilot plant, the overall recovery of cobalt and zinc exceeded 99 per cent with a raffinate containing only 4 mg/L Zn and 1 mg/L Co. The DSX organic system showed no sign of degradation during the pilot plant operation, indicating good chemical stability under the anticipated commercial operating conditions. The DSX circuit will be implemented in the future Boleo processing plant.

Sep 13, 2010

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D A. Bowman, S Schafrik

With the goal of reducing injuries and fatalities related to haul truck accidents, this research investigates technologies and intervention strategies for improving worker training using a virtual environment (VE). Funded by the National Institute for Occupational Safety and Health (NIOSH), this research specifically focuses on training workers in preshift inspections of haul trucks to avoid preventable defects from causing worker injuries and expensive equipment damage. Improved training in these inspections is expected to increase uptime. The VE developed to train workers for preshift inspections consists of three phases: the virtual tour, the virtual inspection and the shift simulation. The virtual tour introduces information necessary to conduct a preshift inspection by guiding the worker around a haul truck, identifying parts to be inspected and explaining defects to look for. The virtual inspection assesses retention as the worker navigates around a haul truck and identifies defects. During the shift simulation, the worker is shown a simulation of the work shift, which animates severe consequences of any overlooked defects to emphasise the importance of preshift inspections. To provide multiple training platforms, desktop and CAVEÖ versions of the training VE were created. Flux Studio was used to model the environment and to produce Virtual Reality Modelling Language (VRML) files for the desktop version. DIVERSE, an application programming interface, was then used to implement a more realistic version of the VE in a CAVEÖ, a room-sized visualisation system. Initial feedback from mining colleagues indicates that the training VE may replace normal classroom training for preshift inspections in the future. As opposed to PowerPoint presentations and instructional videos, the training VE provides better spatial understanding of the location of parts and incorporates interactive features to actively engage drivers in the learning process, which may result in better retention. Initial feedback also indicates that minor improvements can be made to the virtual tour and virtual inspection phases.

Jan 1, 2008

By G J. Massoth, K Faure, A G, R G. Ditchburn, I J. Graham

From modest beginnings in 1996, research into the mineral potential of New ZealandÆs Exclusive Economic Zone has progressed into a major multidisciplinary component of GNSÆs recently funded 6-year æMineral Wealth of NZ and its EEZÆ Programme. In excess of $7.5 M of research funding has been expended, plus $10 M leveraged via collaborations with NIWA (NZ), NOAA (USA), JAMSTEC (Japan), U. Kiel (Germany) and ANU (Australia), whose scientists have contributed hugely to research cruises, as well as subsequent analysis and publication. The 1999 NZAPLUME I cruise was the first research expedition to systematically locate, and chemically characterise, submarine hydrothermal venting associated with arc volcanoes of the southern part the Kermadec intra oceanic arc system. This was followed by the 2002 NZAPLUME II and 2004 NZAPLUME III cruises to the mid- and northern-sections of the Kermadec arc, respectively. Combined, these cruises have surveyed 1300 km of the volcanic chain (from Whakatane to Monowai), including 34 major volcanic centres. Together with concurrent surveys in the Tonga arc, this is now the longest continuous stretch of intra oceanic arc to be surveyed for hydrothermal emissions. Most of the volcanic centres are characterised by simple cones although 30 per cent contain caldera complexes, and compositions range from basalt through to rhyolite. Massive sulphide mineralisation has been recovered from several volcanic centres in the southern Kermadecs (Clark, Rumble II West and Brothers), suggesting the existence of significant Au and base metal bearing deposits along the arc front.

Jan 1, 2005

Media Type Effect on Grinding Efficiency

Sep 13, 2010

By J T. Sharp, M A. Styler, D McGowan, P W. Mayne

Static liquefaction is a geotechnical hazard in mine tailings facilities. Soils that are contractive in shear are susceptible to static liquefaction. Tailings facilities are dynamic structures, typically growing in height each year. Dilative tailings may become contractive under increased effective stress. In this paper we show that Cone Penetration Test (CPT) data can be used to estimate the future state of in-place tailings under changes in effective stress. Susceptibility to static liquefaction is typically evaluated with the CPT by using a clean-sand equivalent normalized cone tip resistance (Qtn,cs) or by estimating the state parameter (?). An alternative approach is to evaluate the soil-state using the yield-stress-ratio (YSR = ?’y/?’v0). If the YSR equals one it is on the normal consolidation line and the soil-state is contractive. YSR values greater than three are typically dense of the critical state line (CSL) and the soil-state is dilative. In this paper we review how to calculate Qtn,cs, ?, and ?’y; and how the YSR can be used to screen for contractive soil behaviour. Unlike Qtn,cs and ?, it is very simple to estimate how the YSR will change due to an increase in overburden stress. This YSR approach was evaluated at three locations that saw increases in overburden of 10 m, 20 m, and 25 m. We show that the ?’y calculations are consistent and the increase in effective stress moves the soil state towards looser soil states. CITATION:Styler, M A, Mayne, P W, McGowan, D and Sharp, J T, 2018. Predicting changes in static liquefaction susceptibility using cone penetration test results, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 317–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By S Bluhm, L van den Berg

In planning mine ventilation systems, heat issues are normally associated with deep-level mines where auto-compression and virgin rock temperatures play a major role. However, a number of mines suffer from high ambient temperatures and humidity, very steep virgin rock temperature gradients and an influx of hot groundwater. Mines in Australia and, particularly, South-East Asia have to deal with these environmental conditions, both in the operational and planning phases. These operations normally have to take heat into consideration during the planning stages at much shallower depths. In high rainfall regions, the water table is saturated and groundwater flow rates are particularly high, which add significant water heat load potential to the mine ventilation system.This paper considers the ventilation challenges associated with hot groundwater conditions in mechanised mines. The paper is based on specific project experience gained from a number of projects in the United States, Australia and South-East Asia and draws on data from mines that experience hot groundwater conditions. For one site, actual decline temperature survey measurements, modelling techniques, management strategies and design considerations are presented.CITATION:Van den Berg, L and Bluhm, S, 2015. Ventilation planning considerations when dealing with hot groundwater, in Proceedings The Australian Mine Ventilation Conference, pp 211–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By R Harding, T Hunt

For the past 120 years, Portland cement manufacture has been undertaken on the shores of the Whangarei Harbour in northern New Zealand. Through a serendipitous conjunction of geo-chemistry, the argillaceous marl found on Limestone Island in the harbour and Tikorangi Hill provides a perfect mix of the various elements required for strong and durable cement. Golden Bay Cement, and its predecessors, have been the guardians and managers of the use of these minerals. As the demands of the concrete industry have increased, so have the needs of the manufacturing process. Careful mapping of the resource at both Portland and Wilsonville Quarries has been undertaken. This has allowed the Company to change the Quarry operation from a purely volume basis to one of selection and blending of constituent minerals. Within the manufacturing process, change has also been introduced. Analytical techniques, using x-ray fluorescence spectrometry, microscopy and the application of modem data collation, has allowed fine tuning of the process. The Company now produces an increasing diverse range of products for both the domestic New Zealand market and exports to various South Pacific countries. This paper discusses the processing of limestone and æcement rockÆ into cement clinker, an intermediate synthetic mineral ground into cement. It examines control and blending regimes, and some methods used in determining process efficiency. An important technique ærediscoveredÆ has been the application of microscopy to clinker.  Examination of the major silicate minerals enables interpretation of the kiln processing and feedback to process operators. It also enables a prediction of indicated performance when ground into cement. Examples this paper give an insight into the use of minerals from Northland in some of the more important construction projects in modem New Zealand.

Jan 1, 1999