Search Documents

By R. T. Hukki, P. Voutilainen

This paper describes a new apparatus for continuous wet fine-screening. Its preferred size range seems to be from 0.1 to 1 mm. The supercritical trommel screen is a short cylindrical trommel of wedge-bar type construction operated at a speed greater than the calculated theoretical critical speed and at a speed lower than the speed at which particles introduced into it will centrifuge. The paper describes results obtained with the prototype supercritical trommel screen in pilot plant scale. The results point to a high capacity and simultaneously to a high sharpness of screening. Finally, an analysis is presented of the forces acting in screening on a supercritical trommel screen. In the era of high speed, high capacity processing of raw materials the conventional slowly rotating trommel screen is often considered a relic from the times passed. A typical trommel screen is the cylindrical trommel rotated about a horizontal or slanting axis at a relatively low speed. Its screening characteristics are well known. Trommel screens of various types of construction, methods of operation, performances and other characteristics have been described in detail by Taggart.1 The theoretical critical speed of a trommel screen is defined by the same well known equation as that applied for grinding mills: where ncritical = the numerical value of the theoretical critical speed in rpm, D 1 = the inside diameter of the trommel in feet, and D2 = the inside diameter of the trommel in meters. ncritical corresponds also to the centrifuging speed provided that the coefficient of friction f between the trommel surface and the outer layer of the charge is = 1.0. In a general case: From Eq. 2 it is seen that in all cases where f < 1.0 the centrifuging speed of the trommel is greater than the theoretical critical speed. The supercritical trommel screen concerns screening operations within that speed range which is between the theoretical critical speed defined by Eq. 1 and the centrifuging speed defined by Eq. 2, under conditions such that the coefficient of friction f<1.0. It is reported by Taggartl that the optimum speed of a conventional cylindrical trommel screen 36 in. in diam was experimentally found to be about 16 rpm. From Eq. 1, the critical speed of this trommel is 44.2 tpm. The indicated optimum speed corresponds to (16/44.2) x 100% = 36.2% of the theoretical critical speed. The optimum speed range based on information available seems to vary from 33% up to 45% of the theoretical critical value. The trommel screen operated at a supercritical speed: operates at a speed greater than the calculated theoretical critical speed; operates at a speed lower than the speed at which the charge introduced into it will centrifuge; operates within the supercritical speed range in such a way that the coarse fraction of the charge must slide in respect to the inside surface of the trommel; the outer layer of the said fraction next to the screen tends to proceed in the same direction as any selected point on the trommel surface, but now at a lower speed, and indeed at a subcritical speed; allows to a certain degree adjustment of the maximum determining particle size x of the fine product simply by a variation of the speed of the trommel within the supercritical speed range. With increasing trommel speed, finer and finer material only will get the opportunity to find its way into the fine product while the screen opening remains constant. In conventional practice, the low speed trommel is generally used for sizing of coarse and medium coarse material, but seldom for fine screening. The characteristic feature of the product passed through the conventional trommel is that the determining size x of the biggest particle is barely smaller than the nominal size of screen opening. The supercritical trommel screen, on the other hand, is best suited for sizing of relatively fine material. Furthermore, the characteristic determining size x of the biggest particle in the fine product can be substantially smaller than the nominal width of the screen opening or slot. In the trommel screen best suited for the applications

Jan 1, 1965

By D. Muraoka

Introduction Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Basin of southwestern Wyoming. Stauffer Chemical Co. of Wyoming, a jointly owned subsidiary of Stauffer Chemical Co. and Rocky Mountain Energy Co., mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of about 1.8 Mt (2 million st) per year of soda ash. The refinery has five parallel operating trains using the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with refinery feed (less than peagravel size material) entering the process. Oversize is conveyed to an outdoor stockpile. Ore is recycled from under the stockpile via cone feeders as the refinery needs require. The ore is conveyed to hammer type crushers and screened. The refinery feed enters the process and the oversize is recycled to the crushers. Calcining The first step in refining trona to soda ash is calcining the trona ore. This is accomplished in concurrent flow, rotary kilns that are direct fired with natural gas. [2 (Na CO NaHCO 2H O) Heat 3Na CO + 5H20 + CO 2 3~3~ 2 ~~2 32] The trona ore is fed to the kiln at the burner end and is intimately mixed with the hot exhaust gases from the burner. Direct contact with the flame is avoided. The ore moves down the kiln by gravity and rotation aided by the kiln&apos;s internal lifters. The exhaust gases are cleaned to 99 + % particulate removal and discharged to the atmosphere. Dissolving the Calcined Trona The calcined trona is conveyed from the kiln discharge to a rotary drum dissolver where it is mixed with water and weak solution (unsaturated solution of calcined trona in water). The calcined trona is soluble whereas the impurities, primarily shale, are insoluble. The discharge from the dissolver is a slurry containing saturated solution (about 30% dissolved calcined trona in water), some undissolved calcined trona, insoluble impurities, and organic impurities. The dissolver discharge enters a rake classifier that makes the first solid/liquid separation in the process by removing the heavy undissolved material from the saturated solution. This undissolved material is conveyed to a second rotary drum dissolver and mixed with water to dissolve any remaining calcined trona. The secondary dissolver discharges to a second rake classifier that separates the solids from the liquid. The solids are now primarily insoluble impurities with very little unrecovered calcined trona. These wastes are conveyed to evaporation ponds for disposal. The liquid from the secondary rake is recycled to the primary dissolvers&apos; weak solution system. Returning to the primary rake classifier, the saturated solution which contains suspended insoluble muds is pumped to a thickener. Flocculant is added to aid settling of the suspended muds. The flocculated muds are collected at the bottom of the thickener and pumped to vacuum cloth filters. The adhering saturated solution is separated from the muds that remain on the filter cloth. The recovered solution is returned to the dissolvers&apos; weak solution system. The muds are reslurried and pumped to the evaporation ponds for disposal. Saturated solution, containing some suspended insoluble muds along with the organic impurities, overflows the thickener. Filtering the Saturated Solution The saturated solution overflowing the thickener enters a holding tank where it is pumped to a bank of pressure leaf filters. The suspended muds are captured on the filter leaves while the cleaned saturated solution is pumped to polishing filters. The polishing filters are also leaf pressure type, intended to remove any suspended solids that may pass the primary filters. Organic impurities are removed with activated carbon. The purified solution is now free of insoluble muds and has most of the organic impurities removed. Crystallizing and Drying the Monohydrate The purified saturated solution is pumped to evaporative crystallizers. The solution is circulated from the crystallizer vessel through a heat exchanger. Indirect contact with steam in the heat exchanger causes the saturated solution to boil, thus crystallizing the soda ash in its monohydrate form. Slurry crystal density is maintained in the crystallizer by simulta¬neous feed of fresh saturated solution and drawoff of the slurry.

Jan 1, 1986

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-

By Robert F. Calman

OUTLINE FIVE EXAMPLES OF GOLD-LINKED FINANCINGS 1. Financing the Lupin Mine • Sale of Cdn $40.0 million of 12% preferred shares and Cdn $40.0 million of Gold Purchase Warrants @ $595 per ounce. 2. Financing the Copper Range acquisition • Borrowing 100,000 ounces from a Canadian chartered bank @ US$307 for five years. 3. Financing the Round Mountain expansion • Borrowing up to US $80.0 million in dollars, convertible into gold, repayable over five years from a group of North American banks. 4. Financing the Tenneco Precious Metals Division acquisition •Sale of SFr 110.0 million of ten year 3-718% bonds with warrants to buy 132,000 ounces of gold at US $560. 5. On Forward Sales, Puts and Calls • Gold, Silver, Canadian Dollars, Swiss Francs THE FINANCIAL RULES AT ECHO BAY 1. Never bet the company 2. Equity is the primary form of capital for a gold mining company 3. On debt 4. The Yardsticks for Corporate Decisions 5. Financial Community Relationships 6. Dividend Policy No Text Available Tables Follow

Jan 1, 1990

By Raymond B. Ladoo

Wollastonite is a calcium metasilicate, with the formula CaSiO3; containing theoretically 48.3 pct CaO and 51.7 pct Si02. It is one of many natural and synthetic silicates with varying CaO/SiO2 ratios, with and without water of crystallization. While it is a very common mineral, deposits of sufficient size and purity to be of commercial interest are unusual. There is only one producer (1958) of wollastonite for industrial use in the United States, Godfrey L. Cabot, Inc. at Willsboro, New York. There has been a small production of surface material for ornamental use from near Blythe, California. Carload tests have been made on California wollastonite for making mineral wool and a commercial plant for this purpose was projected in 1957. Properties Wollastonite is monoclinic and commonly occurs in masses or aggregates of bladed or needle-like crystals. It has a perfect cleavage parallel to the long prismatic axis. It is rather brittle and some types grind easily to a very finely fibrous product, but other types, due to interlacing of fibers, are tough and difficult to grind. Mobs hardness is 4.5 to 5; specific gravity 2.8-2.9; index of refraction 1.616 to 1.631; melting point 1,512°C. Color when pure is a brilliant white, but when less pure it may be gray or brown. Luster is vitreous, transparent to translucent. Common mineral associates are garnet (several varieties), diopside, calcite and quartz. The nature of the mineral impurities determines to a large degree the commercial value of a deposit. At Willsboro, New York, the impurities consist chiefly of iron garnet and iron diopside which are both magnetic and so are easily removable by magnetic separation, yielding a nearly theoretically pure product. Some deposits in California contain calcite and quartz which cannot be removed cheaply, thus limiting market possibilities. Occurrence Wollastonite is a contact metamorphic mineral occurring in most places within or associated with impure limestones. The deposits at Willsboro, New York1,2,3,5 consist of two or more beds dipping 15-50°E and striking NW-SE. The main bed, 30 to 70 ft thick, may be traced on the surface for at least 2 ½ miles. In this belt, the Pre-Cambrian Grenville limestone has been injected and partially replaced by the more liquid portions of an anorthositic magma. Buddington and Whitcomb3 have described the rock as "Mixed gneisses, pyroxenite and garnetiferous gneisses and skarns." Prospecting revealed the wollastonite at ten different places in the belt, overlain in most places by a garnet rock. Diamond drilling has proven several million tons with probable reserves around 15 million tons. Interbedded with the wollastonite are beds of garnet from a few inches to several feet in thickness. In the wollastonite ore itself the chief and almost only associated minerals are garnet (mostly almandite but some andradite and grossularite) with small amounts of green hedenbergite. Inasmuch as the almandite and diopside are magnetic they are easily separated from the wollastonite in high intensity magnetic separators. If grossularite should occur in quantity other means of separation would be needed. Wollastonite has been reported at 35 localities in California12 but only those in the Big Maria and Little Maria Mountains, 16 to 20 miles north of Blythe, Riverside County, are

Jan 1, 1960

By Newell Alford

FORECASTS of future timber consumption in soft-coal mining are handicapped by; the lack of adequate experience records for estimating properly the timber requirements of the industry. Data were obtained from plants where records are kept or from operators who collected the information and to these were added FIG. 1.-GROWTH OF POPULATION IN UNITED STATES, FROM PEARL&apos;S ?BIOLOGY OF DEATH." composite figures for the continental United States in 1905 and 1919 1 and for central and. Western Pennsylvania and for Illinois in 1922.2 The result, representing slightly over 928;000,000 net tons, is shown in Table 1. Some of the companies furnishing data were unable to segregate the timber into classes of use but for those who did, Table 2 shows the board feet of posts and cross bars used per ton of coal mined and the, percentage of the total timber consumed that was used in roof support. The wide variation in amounts of timber per ton of coal mined is the result of

Jan 5, 1924

By F. George, W. Tice, M. Salkind

It was found that Al-A13Ni could be readily cold rolled perpendicular to but not parallel to the whiskers. Reductions of more than 98 pct were achieved without cracking by rolling perpendicular to the whiskers, whereas extensive edge cracking was noted after only 15 pct reduction when rolling parallel to the whiskers. The longitudinal and transverse tensile strengths were nearly doubled, and the longitudinal yield strength more than tripled by cold rolling 50 pct in a direction perpendicular to the whiskers. The whiskers exhibited some waviness (elastic bending) as a result of cold rolling, but at very high reductions (greater than 75 pct) whisker fracture and misalignment became significant. A fine dislocation substructure in the matrix consisting of cells attached to the whiskers was pro -duced by cold rolling. Most of- the substructure was readily removed by a 1-hr anneal at 500°C. Cold rolling was found to substantially reduce the thermal stability of the microstructure at 610°C but did not affect the stability at 500°C. FIBER and whisker reinforced composite materials promise significant improvements in properties over conventional materials. Before they find wide use, however, it will be necessary to understand the response of these highly anisotropic materials to common metalworking processes. Most of the nonmetal-lic fiber reinforced materials have very low elongations (a few pct or less) in the direction of fiber alignment. Thus, metalworking techniques such as rolling and forging would not be as broadly applicable to these materials. This investigation was initiated to determine how a composite system consisting of Al3Ni whisker reinforced aluminum responded to rolling, what changes in the microstructure occurred, and the effect of deformation on the mechanical properties. The composite material studied was produced by unidirectional solidification of the A1-Al3Ni eutectic alloy&apos;-7 and consisted of 10 pct by volume of aligned whiskers of Alai in a matrix of aluminum. It should be pointed out that this system is not representative of all composite materials, and the results will therefore not be universally applicable. The A1-Al3Ni system is characterized by: 1) A strong fiber-matrix interfacial bond 2) A ductile matrix 3) A sufficiently low fiber content to allow significant plastic flow between fibers 4) Strong, completely elastic whiskers (tensile strength 400,000 psi, elastic modulus = 20 X 106 psi.1 These factors allow the material to be readily rolled perpendicular to the fibers. If the fiber-matrix bond were not strong, such a weak interface could fail during rolling. A measure of the ability of a composite to be rolled in the transverse direction can be obtained from noting the transverse tensile behavior. In the case of Al-Al3Ni,2 there is considerable ductility (15 to 30 pct). In the case of boron filament reinforced aluminum, for example, the transverse elongation is less than 1 pct,8 and the material could probably not be cold rolled as readily in that direction. EXPERIMENTAL PROCEDURE 3-in. diam ingots of A1-A13Ni eutectic were unidi-rectionally solidified in graphite crucibles. The starting materials consisted of 99.99+ pct pure nickel and aluminum, and the pure eutectic ingots were made with 6.2 wt pct Ni. The unidirectional solidification process (described in detail elsewhere1-3) consists of preparing a master heat of eutectic composition, remelting, and withdrawing the ingot vertically downward through the heat source at a controlled rate so that plane front solidification proceeds upward at a constant velocity. The resulting microstructure consists of 10 pct by volume of whiskers of very high aspect (length to diameter) ratio. The fiber lengths have not been measured because of the difficulty of detecting fiber ends9 but exceeds 104. There is some possibility that the fibers may be continuous within one grain. Flat sheet specimens 2¾ in. sq and approximately 0.2 in. thick containing whiskers parallel to the plane of the sheet and to one edge were used for this study. A1-A13Ni exhibits either a rod-like (high solidification rates) or a blade-like (low solidification rates) whisker morphology,1,3 and both types were studied. Rolling was accomplished using a two-high rolling mill at a speed of approximately 10 fpm. The rolling direction was either parallel to or perpendicular to the direction of growth (direction of whisker alignment). Reductions of from 0.002 to 0.03 in. per pass were used with the most common value being 0.005 in. per pass. Cold rolling of Al-Al3Ni to more than 98 pct reduction in thickness was accomplished with no intermediate anneals. In addition. a series of speci-mens was cold rolled 97 pct with a 1-hr, 500°C anneal in air after each 50 pet reduction. Tensile testing was accomplished using a Tinius-lsen four screw testing machine. Flat sheet specimens + in. wide and between 2 and 2; in. long with the thickness dependent upon rolling reduction, were used. The gage section was in. wide and 1 in. long. Strain was measured using a clip-on LVDT extensome-

Jan 1, 1970

By F. C. Bond

B. H. Bergstrom (Allis-Chalmers Mfg. Co., Milwaukee)—In reading this article, it was difficult to follow through the example given as a starting point in the derivation of the theoretical equation which relates ball size to feed size. A discussion with F. C. Bond led to the following clarification: Bond postulates that "the breaking force exerted by a ball varies ... as the cube of its diameter . . ." and that the force in pounds per square inch required to break a particle varies ... as its diameter squared." He concludes: "It follows that when a l-in. ball breaks a 1-mm particle, a 2-in. ball will break a 4-mm particle, and a 3-in. ball a 9-mm particle." The above example can be true only for a different set of assumptions. Since the first assumption is apparently true, it is the second that must be revised. The second assumption should read that the breaking force required to break a particle varies as its diameter to the 3/2 power. This relationship was derived in the next paragraph of the article.

Jan 1, 1960

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955

By A. U. Seybolt, V. A. Phillips

Binary iron alloys containing 1 pct of Al, Cr, Mn, Mo, Si, Ti, or V, and 0.4 pct C, 1 pct Cr steels with and without 1.2 pct A1 or 2.0 pct Ti additions, were ion-nilrided at 550° to 600° in N-H mixtures. Nitriding increased the inicrohardne ss of all the binary alloys except those containing manganese or molybdenutn, and also hardened the heat-treated steels if aluminum or titanium urns present. Transmission electron microscopy revealed particle formation in all casts where hardening occurred. Electron diffraction gare positive identifications for ALN, CrN, and a, Si3N4 in the binary alloys, and AlN and CrN in the aluminum- cold chromium-bearing steels, respectil&apos;uly. Cubic VN with a, = 4.13A was tentatively identified. Particles, apparently of CrN, also formed in the base steel but did not increase the hardness very much. Chromium and vanadium formed nitride platelets on {001}° matrix planes, while titanium gave clusters <15A diam. Aluminum nitride precipitated at grain and subgrain boundaries, and within the grains. Silicon gave profuse precipitates of several Morphologies at grain boundaries and cubical particles within the grains. No effect of the alloy carbides on nitride precipitation was observed in the heat-treated steels. THE nitriding of steel has been a well-established commercial process for about 40 years, but in spite of this comparatively long period of use there have been few studies aimed at understanding the process. Most studies, like the early but very competent work of Jones and organ&apos; and nones.&apos; were concerned with establishing the pertinent engineering variables of steel composition, gas composition, temperature, and time. As far as the present authors are aware, there have been no studies of the composition, size, shape, or distribution of the nitrides formed in the nitriding of steel. Noren and Kindbom3 did, however, examine a few nitrided steels by surface replica electron microscopy, and were able to show the presence of car-bonitrides and AlN and TiN nitrides. pitsch4,5 and Hrivnak6 examined nitrided pure iron by transmission electron microscopy. Baird7 found manganese nitrides in Fe-1.6 pct Mn when nitrided at 650°C, using the same technique. In the present work, emphasis was placed on transmission electron microscopy because of its inherently better resolution, using principally binary alloys of iron containing 1 pct of alloying element. In addition, a few simple 0.4 pct C steel compositions were examined to investigate possible carbonitride formation. It was not anticipated that all of the added elements would form nitrides under the conditions used, but it was considered desirable to obtain direct experimental evidence on this point. It would be considerably easier to ascertain the presence of alloy nitrides by examining appropriate binary alloys in preference to relatively complex steels. The work reported here could have been done using orthodox ammonia-nitriding procedures, but an operating ion-nitriding equipment was available, and was therefore used for specimen preparation. EXPERIMENTAL DETAILS 1) Materials. Binary alloys were made up from vacuum-melted electrolytic iron with 1 wt pct additions of Cr, Ti, V, Al, Mn, Mo, and Si of about 99.9 pct purity. In addition, three steels were similarly made up—a basis steel with 1 wt pct Cr and 0.4 wt pct C and two steels with further additions of 1.2 wt pct A1 or 2.0 wt pct Ti, respectively. The materials were vacuum-melted and cast as 11-lb heats into tapered square molds of about 2 by 2 in. average cross section. The castings were forged and hot-rolled to 11/4 in. rounds. Discs of 4 in. thickness by about 1 in. diam were machined from the rods. Some of these discs were hot-forged and hot-rolled to about 0.020 in. thick, sand-blasted, and then cold-rolled to about 0.003 in. thick. At this point, the surface was cleaned by light etching with HC1, then washed, dried, and vapor-degreased prior to nitriding. 2) Ion-Nitriding Procedure. The type of ion-nitriding equipment used here is similar to that described by Jones and Martin.8 Briefly, a mixture of nitrogen and hydrogen at 5 mm total pressure is placed in a vacuum chamber with a dc potential of 450 to 500 v applied between the work (cathode) and the grounded metal vacuum enclosure (anode). Nitrogen ions are accelerated to the work where a thin layer of Fe4N forms on the surface and thus sets up a nitrogen concentration gradient. This causes nitrogen atoms to diffuse into the surface layers of the alloy forming a finely divided dispersion of alloy nitrides, causing hardening of the surface. In the work to be reported here. the nitriding was carried out at 550° to 600°C to be consistent with commercial nitriding practice. The temperatures cited are those measured by a thermocouple located under a platform on which the work was sitting. Except where otherwise stated, the mixture used in nitriding the binary alloys contained -2.0 pct N, balance hydrogen. The nitrogen concentration in the nitriding gas mixture used for the binary alloys was purposely kept lower than normally used in nitriding steels. 10 to 20 pct, in order to minimize Fe4N formation. In this way only the alloy nitrides would be present as a second phase. However, in the case of steels which would contain a- carbide phase along with as

Jan 1, 1969

By Alfonso Merlini

DIFFERENT explanations have been given by the two current theories of the annealing textures for the variation of annealing texture with the annealing temperature observed in rolled polycrystal-line aluminum,&apos; copper,2 and brass, And in rolled single crystals of copperk and silicon iron.&apos; The theory

Jan 1, 1957

By Robert H. Richards

In the latter part of December a batch of amalgam was retorted and the tin in the retort uncovered while at a low red heat, and allowed to cool slowly to a temperature more suitable for ladling into moulds. It was then ladled and made what appeared to be nice, white, malleable block tin. On February 15th our attention is called to the fact that the tin is brittle, and on examination we find that the molecular condition of the pigs has changed to the extent of one-half its material. The change shows itself by an enlargement appearing on the surface something like crystallization, and comes in spots. The condition of the metal in these spots is very peculiar. It has changed from a malleable metal to a brittle one, with a structure somewhat resembling stibnite, and a color very considerably darker gray than tin. The analyses of the two parts of this tin pig showed the following results: Mercury. Tin. Specific Gravity. Crystalline part,.....2.62 97.24 6.175 Malleable part,.....2.38 97.50 7.387

Jan 1, 1883

By V. C. Allen

THE Tri-State Zinc, Inc., Galena, Ill., was confronted with the problem of securing ore from a deposit because the hoisting shaft was several thousand feet from the mill. The orebody is several thousand feet long, averaging 200 ft in width and 60 ft in height and opened up by vertical shafts some 300 ft deep. Mining is by the room-and-pillar method. During the initial operation the ore was loaded by conventional electric 1/2 -yd boom-and-dipper shovels and hauled to the shaft by 8-ton diesel trucks. This underground ore loading and hauling was well adapted to the conditions and productive of low costs per ton. However, with the mill situated as mentioned, a triple handling of all broken rock was necessary: 1-from the stope to the shaft by truck, 2-up the shaft by skip or can into the surface hopper, and 3-by truck from the surface hopper to the crushing plant at the mill. In addition to the repeated handling, serious troubles were encountered during the winter because of freezing in the shaft hopper.

Jan 6, 1951

Reports on process control computer projects at the Kamioka Plant are summarized from the Japanese technical literature (see references). Fluidized Bed Roaster and Sulfuric Acid plant1 A small process control computer (Yokogawa CCS-200 with an OKITAC 5090P 8K central processor) was installed in the Kamioka smelter in the summer of 1964. A year-and-one-half installation project followed, which successfully brought the roaster and acid converters under computer control. The process plant consisted of two 130 RPD fluosolids roasters and two Monsan to acid units. The roasters are charged with lead-zinc concentrates with SO2 from the roaster processed to sulfuric acid. The computer system provides the following functions: 1) log data from the plant--the input is taken from 50 analog signals, 130 high-low digital alarm points, and 50 analog high- low alarm points; 2) set-point control on 18 control loops; 3) direct digital control (DDC) on eight control loops for which conventional controllers were difficult to adapt due to abnormal loop characteristics or delay times; 4) execution of a safe shut-down procedure

Jan 1, 1969

By B. G. Bunting, D. L. Abata, J. Robb, J. H. Johnson

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during mining operations. The explosives included two semi-gelatin dynamites, three slurry explosives, and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and toxic gases produced by the detonation were trapped at the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/1bm): NO, 0.0100-0.035; N02, 0.003-0.019; CO, 0.08-0.30; SO2, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1983

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

ThE solubility of carbon in tantalum has been reported to be very low at temperatures below 1500 C,1&apos;2 increasing to at least 0.02 wt pctl at the eutectic temperature of 2800°C. The solubility limits at low temperatures were based on metallo-

Jan 1, 1963

By A. R. Sims

Are from the Greater Butte Project is hoisted through the new Kelley shaft. In 1946 when plans were formulated for the Kelley mine, two test cave blocks were mined by using the facilities of the old St. Lawrence mine. These blocks, known as the Adams No. 1 and Adams No. 2, produced more than half a million tons of ore. The experiment proved beyond all doubt that cave mining was possible- and economical-in Butte. Adams No. 1 was patterned after Inspiration cave blocks. Adams No. 2 was a slusher type, with the slusher lane on the first floor above the haulage crosscut and at right angles to it. Thirty-horsepower electric hoists slushed ore from 48-in. scraper buckets directly into cars for haulage to the shaft. These cars were the 57-cu ft Granby type hauled by 6-ton battery locomotives over 40-lb, 18-in. gage track. Prior to this time the largest slushing machines used at Butte were 15-hp electric hoists pulling 36-in. scrapers.

Dec 1, 1956

By P. E. Doherty, B. Chalmers

Subboundaries may be revealed in aluminum by the formation of pits on the surface during cooling from elevated temperatures. The pits do not form in the vicinity of high- or low-angle boundaries. They are attributed to the condensation of vacancies from a super saturation produced during coolirzg. Using the vacancy pit and Schulz X-ray techniques for observing low-angle boundaries, a study was made of the transition from the nearly perfect seed to the striated structuke characterist-ic of aluminum crystals grown from the melt. It was found that the individual striation boundaries develop by the coalescence of very small-angle boundaries, as well as by the addition of individual dislocations. Several mechanisms for the formation of striations are discussed. Evidence was found suggesting that a super-saturation of vacancies exists near a growing interface, and it is proposed that the resulting climb of existing dislocalions produces "half&apos;-loops" at the interface, which combine to form the low-angle striation boundaries. LINEAGE, or "striation" boundaries, have been studied in detail by Teghtsoonian and Chalmers 1,2 in crystals of tin grown from the melt, and by Atwater and Chalmers3 in lead. They found that single crystals grown from the melt consist of regions which are separated by subboundaries that lie roughly parallel to the growth direction. A difference in orientation of 0.5 to 3 deg exists between the striated regions; the misorientation is such that the lattice of one region could be brought into coincidence with the lattice of its neighbor by a rotation about an axis approximately parallel to the direction of growth of the crystal. They observed an incubation distance for the formation of striations which increased with decreasing growth rate. They also found that in any crystal, the sum of all rotations of the lattice in one sense, in going from one striation to the next, is very nearly equal to the sum of all the rotations in the opposite sense. A striation boundary, which is a low-angle grain boundary, can be described as an array of dislocations. If it is assumed that suitable dislocations are introduced into the crystal during solidification, the formation of striation boundaries can be explained as a result of the migration of the disloca- tions into arrays. The formation of arrays is energetically favorable since the energy of an assembly of dislocations can be reduced by the interaction of the stress fields when a suitable array is formed. This investigation presents and interprets new information concerning the nature and origin of striation boundaries in aluminum. EXPERIMENTAL TECHNIQUE Single crystals of high-purity aluminum (Alcoa 99.992 pct) were prepared by horizontal growth from the melt.&apos;&apos; The specimens were subsequently electropolished in a solution of 5 parts methanol to 1 part perchloric acid kept between -10° and 0°C in a bath of dry ice and alcohol. The current density was approximately 6 amps per sq in. Doherty and Davis9 have shown that in aluminum sub-boundaries with misorientations of not less than several seconds of arc may be revealed by the vacancy pit technique. During cooling from elevated temperatures pits form on electropolished surfaces of aluminum crystals as a result of the condensation of vacancies.11 Pits do not form in the vicinity of small- or large-angle grain boundaries, presumably because such boundaries act as sinks for vacancies. Boundaries of misorientations down to 3 sec of arc are revealed as pit-free regions, see Fig. 1. The Schulz X-ray technique12 was used to determine the angular misorientations of subboundaries. In this method, white radiation from a micro-focus X-ray tube is used to produce an image of a fairly large area of a single crystal surface. Subboundaries cause splitting in the diffracted image, see Fig. 2. Misorientations down to about 15 sec of arc may be observed with this technique. OBSERVATIONS AND DISCUSSION Figure 1 shows a striated aluminum crystal grown at 10 cm per hr etched by the vacancy pit technique. An incubation distance of about 1 cm is observed before the initiation of striation boundaries. Fig. 2 is a Schulz X-ray photograph of a striated crystal similar to that shown in Fig. 1. A large area of the crystal was studied by means of a series of photographs. Fig. 2, which is a reflection from the (100) plane, included about the first 4 cm of crystal to freeze. There is an incubation distance of about 1 cm, and a distance of about 2 cm over which the angle of misorientation builds up to its final value of approximately one degree. Some twist component can be seen in Fig. 2 at the right side of the photograph. From Fig. 2 it can be seen that the sum of all rotations of the lattice in one

Jan 1, 1962

By K. Osseo-Asare

The thermodynamics of solid-aqueous solution equilibria up to 200°C In the systems Me-NH3 H2 0 (Me=Cu, Ni, Co) are summarized with predominance area diagrams generated with the DIAGRAM computer program. The implications of the diagrams to ammonia hydrometallurgy are discussed.

Jan 1, 1981

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating tables of modern design on unclassified feeds of --1/2 in. particle sizes, including tests on high-sulphur coals.

Jan 9, 1950