Search Documents

By Charles W. Carter, Alfred H. Bell

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year's total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By Alfred H. Bell, Charles W. Carter

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year's total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By Charles Morgan

AN increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). PROSPECTING Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body.

Jan 1, 1937

By J. A. Dos Santos

High angle conveyor (HA C) systems in open-¬pit mining offer many advantages over the traditional, truck only, haulage systems. These include superior energy efficiency, less dependency on petroleum products, less sensitivity to inflation, less excavation for the amount of ore recovered, and less ramp construction and maintenance costs. Various high angle conveying systems and the corresponding characteristics of the high angle conveyor are illustrated. Discussion includes the range of HAC systems from the low capacity (up to 1.8 kt/h or 2000 stph), low lift (10.7 to 36.6 m or 35 to 120 ft), continuously mobile to the moderate capacity (1.8 to 3.6 kt/h or 2000 to 4000 stph), moderate lift (36.6 to 76.2 m or 120 to 250 ft), intermittently mobile to the high capacity (greater than 3.6 kt/h or 4000 stph), high lift (greater than 76.2 m or 250 ft), semimobile. Combinations of the above as required for the various open-pit mining operations are also discussed.

Jan 1, 1985

By H. J. French

At the request of a committee of the Engineering Division,' National Research Council, a study of the properties of boiler plate at various temperatures up to about 900' F. (482" C.) has been instigated. The following is a report of preliminary tests made on two grades of 1/2-in. plate and includes a description of the apparatus used in the determination of the proportional limit. Detailed reference to- the many published investigations in connection with the properties of steel at various temperatures will be omitted from this report. Suffice to state that results obtained for variation in tensile strength, elongation, and reduction in area with temperature are in substantial agreement with the effects now generally considered to be correct. Comparison of proportional limit values with results obtained by other investigators will be found in the conclusions. Materials Used The steels tested were $1/2-in. (12.7 mm.) open-hearth boiler plate of firebox and marine grades. The specified tensile strength and the analysis for each are shown in Table 1. In the manufacture of this material, a

Jan 1, 1922

By H. J. French

At the request of a committee of the Engineering Division,' National Research Council, a study of the properties of boiler plate at various temperatures up to about 900' F. (482" C.) has been instigated. The following is a report of preliminary tests made on two grades of 1/2-in. plate and includes a description of the apparatus used in the determination of the proportional limit. Detailed reference to- the many published investigations in connection with the properties of steel at various temperatures will be omitted from this report. Suffice to state that results obtained for variation in tensile strength, elongation, and reduction in area with temperature are in substantial agreement with the effects now generally considered to be correct. Comparison of proportional limit values with results obtained by other investigators will be found in the conclusions. Materials Used The steels tested were $1/2-in. (12.7 mm.) open-hearth boiler plate of firebox and marine grades. The specified tensile strength and the analysis for each are shown in Table 1. In the manufacture of this material, a

Jan 1, 1922

By T. Katayanagi, J. Shimoiizaka, K. Nakatsuka

Feldspar has been separated from silica by cationic collector using hydrofluoric acid as an activator of feldspar (1,2). Recently, one of the authors developed a new flotation process separating feldspar from quartz without using hydrofluoric acid. Presently, some silica sand mills are operating to introduce this process in Japan (3). In this flotation, feldspar is floated from silica using normal alkyltri-methylene diamine acetate together with sodium petroleum sulfonate as collectors in a hydrochloric or sulfuric acid circuit of about pH 2. From fundamental studies, it was found that, though the aliphatic diamine by itself did not adsorb on feldspar sufficiently to give a satisfying flotation in acidic circuit., the adsorption of collector was promoted by the simultaneous use of petroleum sulfonate and resulted in sufficient flotation of feldspar. On the other hand, quartz did not float in this flotation process. The application of this flotation was attempted for some types of natural samples and satisfying results were obtained. Further, an example of practical plant was introduced and the advantages in the process are emphasized.

Jan 1, 1976

By W. Joseph Schlitt

The characteristics of successful heap and dump leach operations are first reviewed in a general sense. Then attention is focussed on solution management as the key operating parameter in leaching. The first part of this study includes a detailed conceptual analysis of fluid flow. This identifies the relationships between the flow parameters and the chemical and physical properties of the rock. Then these relationships are extended to practical systems in order to establish optimum application rates and solution distribution methods for heaps and dumps. The study shows that there is a maximum effective application rate, qmax, that can be used without causing solution short circuiting. This rate is a function of the minimum permeability in the heap or dump. The expression for qmax is qmax (gal/ft2/hr)[~]0.9 k (darcies). Here k is the appropriate permeability coefficient. Using this equation, qmax is found to be on the order of 1 gal/ft2/hr (4 cm/hr) for a typical heap or dump leach operation.

Jan 1, 1984

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

SINCE the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error.

Jan 1, 1942

By A. J. Opinsky

ThE superior performance of nonsag tungsten wire in lamps has been ascribed to the large-grained micro-structure that can be developed in it. The orientations of these large grains have been studied several times; most published data1-' appear to be similar to those plotted in Fig. 1. These new data were obtained by X-ray back-reflection Laue technique from all of the large grains occurring in thirteen different wires that had been heated at the lowest possible temperature for the formation of large grains. Here the wire axis is plotted in terms of the principal directions of the cube. Rosi decided that the preferred orientation of the large crystals could be described by a single ideal orientation, (531), being parallel to the wire axis.' Rieck2,3 and Mannerkoski' have essentially confirmed this finding. Opinsky, Orehotsky, and Seigle argued that the data suggest that (211) is parallel to the wire axis instead of a single ideal orientation.5 This {211} contains the (531) ideal orientation and would appear to be a more general case. Ahlborn and Wassermann report that their orientation data stretch from ( 110) through (531) to (311) 8 This is part of the locus of (211). All these investigators have determined the orientations of the large grains by back-reflection Laue techniques. They have all obtained essentially similar results. On the other hand, Swalin and Geisler, who obtained their data by neutron diffraction, indicated that the preferred orientation of the large grains in doped wire is (110) .7 These findings cannot presently be reconciled with the pole density data described in the previous paragraph. Rosi1 and Rieck2 have advanced arguments about how their orientations could occur. Nevertheless, the crystallographic link between the (110) (cold-worked) fiber texture and the preferred orientation of the large grains has remained missing. This link can be provided through the concept of coincidence-type boundaries. Such boundaries separate two grains that have a certain number of common lattice sites. Coincidence relationships that result from rotations about low index directions are given by Brandon et a1 .' What is desired is a calculation of those orientations that bear a coincidence relationship with the (110) fibers of the cold-worked matrix. This situation arises in the following fashion. Heating the tungsten wire for a combination of time and temperature falling short of the formation of the nonsag structure yields a structure that is still fibrous in nature and the preferred orientation remains (110). During grain growth, the growing grain is in contact with these fibers. It is hence possible that the entire process may begin by the passage of a coincidence boundary into a (110) fiber. The calculations were carried out analytically and checked graphically. Following Brandon et a1.,8 coincidence relationships from 1 in 5 to 1 in 19 have been considered. The results of the calculations are given in Fig. 2. Of the coincidences examined, some of those occurring upon rotation about ( 110) come closest to the experimental points in Fig. 1. Nineteen of the twenty-three data points in Fig. 1 can be attributed to the ideal orientations A, B, C, and D in Fig. 2. As determined analytically, three crystals lie within 4 deg of point A, four lie within 21/2 deg of point B, eleven lie within 5 deg of point C, and one lies within 1 deg of point D-a total of nineteen. The off-lying points are near the |110| point of the triangle.

Jan 1, 1968

By H. Colijn

Belt scales are frequently used in the mining industry because of the ability to handle large tonnages without interrupting the material flow, fitting easily into all types of bulk handling systems and being relatively inexpensive. Although manufacturers claim weighing accuracies better than Y2%, many operators experience, in practice, much larger errors and they have become apprehensive about the use of belt scales. However, in spite of these disappointing instances, a belt scale is one of the most valuable tools for process and inventory control. Since it is a measuring device, care should be given to the design and installation of belt scales. The basic components of a belt scale are: (1) conveyor belt, (2) scale suspension, (3) sensing device, (4) integrating and recording. The first component of this system is of great importance to the overall accuracy and has been thoroughly discussed in earlier papers. This paper will review primarily the various scale hardware designs currently available, and will be confined to the last three components of the system.

Jan 1, 1973

By C. G. Dunn, P. K. Koh

TWO recent review papers have considered the origin of primary and secondary recrystalliza-tion textures from the point of view of oriented nucleation and oriented growth theories."' Both theories require nuclei for primary recrystallization but provide no unequivocal answer to the question of what nuclei are. The answer to the same question regarding secondary recrystallization, however, often is that nuclei are certain primary recrystallization grains or primaries. The two theories differ, however, in specifying what the certain primaries are. In support of the oriented growth theory Beck and Hua originally stated "It may be assumed that in a re-crystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as nuclei for the coarse grains, provided that conditions are favorable for their growth." In commenting on this statement one would say that there are two restricting conditions: namely, that 1) the certain primaries (nuclei) are large enough to grow, and 2) their boundaries have high mobility. More recently Beck2 has con-

Jan 1, 1958

By M. L. Fuller

THE fundamental mechanism of the deformation of zinc has been thoroughly described by several prominent investigators, particularly Mark, Polanyi, and Schmid,1 Mathewson and Phillips,2 and Schmid and Wasserman.3 The deformation of zinc occurs primarily through slip along basal planes {00. 1 }, and secondarily through twinning on pyramidal planes of the form { 10.2). In addition to these basic studies on single crystals, there have been a number of determinations4,5 of preferred orientations developed in rolled, polycrystalline zinc. In no case, to our knowledge, has there been described the development of oriented struc-tures in zinc as a result of a, systematic series of rolling treatments. The work included in the present paper shows the changes in orientation produced in a zinc alloy by successively increasing degrees of cold-rolling reduction. This alloy has the same crystal form, hexagonal close-packed, as zinc, but its susceptibility to hardening for a given degree of working is much greater because of its higher recrystal-lization temperature.

Jan 1, 1934

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By John A. Fagnant

At Elkol, Wyo., about 80 miles northeast of Ogden, Utah, the Kemmerer Coal Co. and the Utah Power and Light Co. are involved in a joint venture that will soon see 1 million tons of coal going "out by wire" to Ogden. Kemmerer, owner of a multi-seam strip mine, and the utility, now building a steam power plant adjacent to the mine site, expect to begin initial power generation by February 1963. Although capable of producing only 150,000 kw at that time, this plant is expected to be ultimately enlarged to 500,000-kw capacity which will require about 2 million tons of coal annually. The deposit consists of more than 30 seams of coal, usually varying in thickness from 2 to 40 ft, and separated by beds of sandstones and shales. In certain areas the aggregate thickness of all the coal seams measures 300 ft. The thickest and most spectacular of these seams is the lowest one, referred to as the No. 1 seam, which is 118 ft thick in some places.

Jan 8, 1962

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325.

Jan 8, 1978

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat's depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"'. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"' an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)', four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By E. H. Snow, B. E. Deal

Instability effects in semicanductor devices have long been attributed to the motion of charges on or within oxide layers on the surface. These effects are of critical importance in metal-insulator-semiconductor MIS) field-effect devices. For this reason, the capacitance-voltage or the conductance-voltage characteristic of these devices can be used as a sensitive detector to study charge transport and polarization effects in the oxide or insulator. A review is given of the results of such studies of thermally grown SiO2 as well as of other insulating films of importance in silicon technology. Three types of effects are distinguished. The first of these is the drift of mobile cations within the dielectric, examples being thermally grown SiO, which is often contaminated with sodium ions, and a variety of other glasses in which the mobile ions are a part of the glass composition. The second effect is a dipole-type polarization which occurs in phosphosilicate glass films obtained by reacting P2O5 with thermally grown SiO2. The third effect involves the transfer of charges between the dielectric and the silicon electrode. This occurs in silicon nitride and other deposited dielectrics. It is concluded that MIS studies have provided a powerful technique joy the study of charge transport and polarization effects in insulating films. The knowledge gained from these studies has led to an understanding of surface effects on conventional transistors and diodes as well as making possible stable MIS transistors. THE metal-insulator-semiconductor field-effect transistor is conceptually the oldest type of active semiconductor device.' The earliest attempts at making this device were frustrated because of high surface state densities at the interface between the semiconductor and the gate insulation.' However, by using a silicon substrate with thermally produced silicon dioxide as the gate insulation, this problem was solved and metal-silicon dioxide-silicon devices with good characteristics were made as early as 1960. 3 Yet it was still over 5 years before these devices became a commercial reality. This delay was largly due, not to surface states, but to stability problems associated with polarization effects within the insulating layer which caused the threshold voltage of the device to drift under temperature and bias treatments. The solution to these problems has not only made possible stable MIS devices, but it has added immensely to our understanding of failure mechanisms in conventional bipolar transistors and has added to the reliability of ali types of planar devices. In this review, we shall first describe the effects of various types of polarization phenomena on MIS device characteristics. Then, since thermally grown SiO, is by far the most important insulator used in these devices, we shall review historically the type of instabilities which have been observed in thermal oxides, the attempts at understanding and eliminating them, and the present status of the problem. We shall then turn our attention to the various deposited insulators which have been used, including lead glasses, phosphosilicate glass, vapor-deposited silicon oxide, and silicon nitride. Interestingly enough, many of these materials show polarization effects which are quite different from those generally observed in thermally grown SiO2. THE EFFECTS OF POLARIZATION PHENOMENA ON MIS CHARACTERISTICS The simplest MIS device and the one which has been most frequently used in the study of polarization effects is the MIS capacitor. Two modifications of this structure with single- and double-layer dielectrics are illustrated in Figs. l(a) and (b), respectively. The capacitance of this structure as a function of voltage applied to the metal gate electrode is plotted in Fig. 2 for the case of an n-type silicon substrate. When the silicon surface is accumulated (positive bias) the measured capacitance is just that of the insulating layer C. When the surface is inverted (negative bias), the capacitance is that of the insulator and a silicon depletion layer in series CoCs/(Co + Cs). Indicated on the horizontal axis of Fig. 2 is the voltage VT at which the silicon surface becomes strongly inverted. This voltage corresponds to the threshold or turn-on

Jan 1, 1969