Search Documents

By J. B. Clark, F. N. Rhines

brittlement or notch sensitivity progressively increases. Further, in contrast to results obtained with the impact test, the notch strength for the large specimens does not reveal a 500°F embrittlement range. The notch sensitivity as determined with the 0.3-in. specimen of 4340 steel given the stepped austenitizing treatment has been discussed elsewhere. This quantity as measured for the 1.1-in.- diam notch tensile test and given in Fig. 3, is taken to signify that reduced notch sensitivity is encountered in the 600" to 800°F tempering range for specimens given the stepped austenitizing treatment. The stepped austenitizing treatment may, there- fore, be of use in promoting deeper hardenability for a 4340 steel while at the same time giving reduced notch sensitivity in the high-strength range in which this steel is now being used. Acknowledgments The work reported was supported by the U. S. Navy Bureau of Aeronautics. The authors are indebted to the Bureau of Aeronautics for granting permission to publish results of this research and to N. E. Promisel, H. Hessing, and J. Maltz for their interest.

Jan 1, 1958

By Frank S. Hurley

To comply with the California Mine Safety Orders pertaining to transportation of mine workers over mine railroads, the management of the New Idria mine in San Benito County, Calif., designed special man-cars. The new regulations, dated October 1958, make it mandatory for mine man-cars to be designed for carrying five or more men to and from the mine workings. At the New Idria mine, largest single producer of mercury in the U.S., each shift normally employs about 70 men. However, with the possibility of a future increase in the work force, seven man-cars were constructed with a total carrying capacity of 84 men. The general design of the mine man-cars was dictated by safety regulations plus the physical characteristics of the mine-low headroom, limited side clearance in haulageways, and track irregularities due to ground swells. The cars measure 10 ft long, 44 in. wide, and 50 in. high and were built at an average cost of $450 per car. All assembly work was done at the mine site.

Jan 7, 1960

By J. E. Russell, Y. J. Wang

In this paper, we report the results of a study of the characteristics of Texas lignite based on a proximate analysis data base previously published by the Bureau of Economic Geology, University of Texas at Austin and the U.S. Bureau of Mines. The original impetus for this study was the desire to perform a parameter study in connection with the siting of potential underground gasification tests in Texas. A numerical model of the gasification process was available and required proximate analysis data, among other parameters, as input. If proximate data were available for a particular site, a prediction of the product gas quality could be made. However, in preliminary siting studies, it would be advantageous to know what the desirable characteristics of the lignite are, in order to target general areas for drilling. Consequently, a parameter study was in order. This paper presents the methodology required to systematically vary proximate analysis parameters and estimate the corresponding energy content for various group(or formation)-facies classifications of Texas lignite.

Jan 1, 1983

By Malcolm V. Lowry

At Balmat in northern New York State, the St. Joseph Lead Co.'s 2100-tpd zinc mining and milling operation is utilizing a unique thickener in conjunction with conventional crushing, grinding and flotation methods. From 1930 through 1962, zinc concentrates went directly from flotation to the filtering, drying and loading facilities, all of which had to operate 24 hr per day. Wide fluctuations in tonnage also had to be accommodated due to variations in the grade of ore. Many problems were thus encountered in filtering and drying, but the cost of installing a conventional, large diameter thickener could never be justified. In 1963, after thorough investigation, an unconventional thickener that is unusual in several respects was installed at Balmat. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes.

Jan 5, 1966

By J. S. Jacobi

Treating copper ores by heap-leaching and similar hydrometallurgical means is a time-honored practice, which was well known even in the 19th century. Later the method lost ground to better ore dressing processes, particularly selective. flotation. More recently there has been a distinct reversion to leaching techniques, particularly for scavenging operations in old mining stopes, in connection with LPF systems, irrigation of tailings dumps and similar situations. These hydrometallurgical techniques will gain further ground because processing is simple and permits better extraction of copper, particularly from low-grade or partly oxidized ores. In the lixiviation of primary ores at some major operations, copper-bearing liquors may undergo re-circulation in heap-leaching arrangements or the ores may be subjected to systematic percolation treatment. The liquors resulting from this source usually are quite strong (above 10 gpl copper) and copper would normally be reclaimed by electrowinning or cementation. These processes fall out- side the scope of this paper which is concerned with recovery of copper from weak 1iquor.s containing from 0.1 to about 3 gpl copper.

Jan 9, 1963

NEW MEMBERS The following list comprises the names of those persons who became members during the period of May 10, 1918, to June 10, 1918. ABEEL, GEORGE H., JR., Cons. Min. Engr., .4111 Lafayette Ave., St. Louis, Mo. ALLEN, CARL A Metal Min. Engr., U. S. Bureau of Mines, Butte, Mont. BECKER P. FRANK Engr., Lightner Min. Co., 35 Nassau St., New York, N. Y. BOCK, JAMES H., Steam Shovel Foreman, Chino Copper Co., Santa Rita, N. M. CARRON, FRANK X., Civ. and Min. Engr Rock Springs, Wyo. CROWE, THOMAS B., Mill Supt., Portland Mill, Portland Gold Min. Co., Victor, Colo. DOBSON, PERCY GRENSIDE, Min. Engr. and Geol., Crow's Nest Pass Coal Co., Fernie B. C., Canada. ESTABROOK, W. H., Capt., 3d Bat. 20th Engineers, A. E. F., Care postmaster, N.Y. FRASER, 0. B. J., Engr., International Nickel Co. of Canada, Ltd., Port Colborne, Ont., Canada. GARRIDO,. MANUEL F., Min. Engr 109 W. Myrtle St., San Antonio, Tex. GRODSKY, VLADIMIR ALEXANDROVITCH, Cons. Engr., Motor Products Corpn., Detroit, Mich.

Jan 7, 1918

By Carlos D. da Gama, Charles R. Nelson

Griffith’s theory of brittle fracture, as modified by McClintock and Walsh to fit rock behavior in cases of failure by compression, has been successfully applied in various fields of rock mechanics. Extension of the Griffith's criterion to rock blasting problems may also be more representative of rock behavior than the simple consideration of a criterion of failure based on the dynamic tensile strength of the material. If consideration is given to pre-existing cracks within rock structure, occurring not only because of the discontinuous properties of rocks, but also as a result of drilling operations that normally precede blasting, those cracks can be propagated under the action of the dynamic stresses (radial and tangential) induced by the passage of the wave emitted by the explosion. Conditions for initiation and propagation of pre-existing cracks are deduced in terms of rock properties and explosives performance. Influence of the different variables governing the phenomenon is discussed after considering an actual example. Results seem to be well correlated with experimental evidence of radial cracking observed in blasting with high explosives acting within hard rock.

Jan 1, 1971

By William D. Carter

When the first Earth Resources Technology satellite (ERTS-A) is orbited by NASA next year, mineral exploration is expected to take a giant leap forward. There are many inherent advantages in going to space to study large regions of the earth, as existing space data have shown. A preview of what can be expected has already been provided by Gemini and Apollo color photographs taken over many parts of the world in the equatorial belt to 30ºN and S latitude. These comprehensive views cover some 100 sq mi, depicting prominent geologic features in a regional context. Placed side by side with mosaics of aerial photographs covering identical areas, the space pictures point up many inadequacies in the present airborne methods of data acquisition. To obtain a regional picture from aircraft, one must piece together many bits of data, and the final result suffers from variations in lighting and photographic reproduction that may obscure features important to the mineral explorer. By contrast, space photographs provide unsegmented synoptic views of large areas as they appear in a single instant under uniform lighting conditions.

Jan 1, 1971

By David E. Fogelson, James J. Olson

Rock mechanics as a guide to a safe underground operation is gaining importance as more is under- stood of rock behavior under stress and of the competency of rock after blasting. The U. S. Bureau of Mines' Twin Cities Mining Research Center and White Pine Copper Co. personnel undertook a joint research program recently to define how the rock adjacent to a newly opened underground working could be left as undisturbed as possible. The goal was to leave a competent structure which would tend to limit rock falls and thus decrease the incidence of fatalities from this greatest of all underground hazards. High-amplitude stress waves and borehole gases create a crushed zone in the rock, the thickness of which is about equal to the borehole radius. Beyond the crushed zone, additional structural damage occurs to the rock from the microstructural level up to visible fractures that may extend several feet. This type of rock damage near the final excavation lines reduces rock strength and increases the possibility of failure of the openings from subsequent vibrations or stresses.

Jan 9, 1969

By Luis Toron, Salvador Cortes-Obregon

THE Oaxaca coal fields, shown in Fig. 1, are located in the Alta Mixteca region in the states of Oaxaca, Puebla, and Guerrero. Known out crops are scattered over 3125 square miles. It is probable that further exploration will reveal a more extensive area of deposits. The region is of great importance to Mexico, as at present the only sources of coal are the fields near the U. S. border. Steel mills are also located in the North, and finished products must travel 600 to 800 miles to the area of consumption in central Mexico. The Oaxaca coal, only 120 miles south of Mexico, D.F., lies close to several iron ore deposits. If this coal can be used in steel production is will be possible for the Mexican steel industry to reach new dimensions, commensurate with the growing industry of the central region. Coal can be utilized in thermoelectric plants in this area, which lacks not only petroleum and natural gas but also electric power. It can be used as domestic fuel, replacing charcoal and firewood.

Jan 5, 1954

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historic Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon-in-leach for recovery of gold from ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a coarse rock fraction from the grinding SAG mill circuit. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900's. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1984

By N. C. Nissen, J. A. Thomas, A. Illis, K. N. Subramanian

Successful miniplant and laboratory testwork has indicated that high purity selenium can be produced from copper refinery slimes. The recovery technique fits into existing unit operations, and the selenium recovery in the new process was close to 99%. This recovery virtually eliminated any selenium being processed through the smelting stage. In addition, miniplant tests conducted at Inco Metals Co.'s J. Roy Gordon Research Laboratory in Mississauga, Ontario, have demonstrated the reliability of the process with respect to extractions, product quality, filtration characteristics, and effluent disposal. Inco's copper refinery at Copper Cliff, Ontario, produces about 500 t/d of copper with the anode slimes fall typically averaging 0.5% of the throughput. Investigations relating to the treatment of slimes within Inco's R&D have been conducted on several occasions since 1959, when the available alternatives such as acid or alkaline pressure leaching, aqueous or high temperature chlorination, roasting, smelting, etc., were considered. Interest in slimes processing was revived recently to meet increasingly stringent environmental standards and to replace equipment of a relatively old plant.

Jan 11, 1978

By Harold J. Bennett

A comprehensive knowledge of the availability of mineral resources to evaluate and assure a dependable supply is a prerequisite in establishing and maintaining a viable national economy. Since no nation is self-sufficient in all its mineral needs, its prosperity depends to a great degree upon its developing and maintaining an effective national minerals policy. This must be preceded by a systematic inventory of mineral resources that may be available to that nation. The U.S. Bureau of Mines is implementing a mineral deposit inventory program of domestic and foreign mineral occurrences, with initial emphasis on the domestic. In order to provide an in-depth appraisal of minerals availability, the approach includes not only realistic estimates of quantity and quality, but other essential factors such as costs, technology, environmental constraints, and development-time requirements. Analysis of this information provides usable relationships of quantity, price, time, and associated degrees of confidence of the occurrence of identifiable mineral resources. Keeping pace with a changing minerals industry and handling the large volume of information required in this undertaking demands that computer methods be employed.

Jan 1, 1977

MORE than 2500 members of the AIME from all sections of the U. S., Canada, Central and South America are expected to attend the 175th General Meeting scheduled for Los Angeles Feb. 16 to 21, 1953. The Southern California Section will be host for the meeting. It will be the first time the Annual Meeting has been held in Los Angeles. In keeping with the historic nature of the event, headquarters will be the fabulous Statler Hotel, recently opened in downtown Los Angeles. Meeting plans are under the direction of Henry T. Mudd, General Chairman, assisted by members of the Southern California Section, headed by Basil P. Kantzer. The annual business meeting is scheduled to be held Tuesday, February 17, at the Statler Hotel, at 4 pm. Minerals Beneficiation Div. has planned a very important program, with 10 technical sessions, the famous Scotch Breakfast, divisional luncheon, and participation in the Mining Branch and All-Institute activities. The MBD business meeting is set for the morning of Feb. 16, 1953.

Jan 1, 1952

The following communication has just reached the Institute, from the office of the Provincial Geologist, Department of Lands,-Forests and Mines, Ontario, Canada: During the autumn of 1917 gold was discovered in unsurveyed territory south of Lake Abitibi in northeastern Ontario. This area lies about 70 miles almost directly east of the well known Porcupine area. During the coming summer, the Ontario Bureau of Mines is to make a geological survey of this new gold area. Following the custom of Ontario, this area is being divided into townships, 6 miles square. These townships have recently been given the following names in honor of men well known in the mining and geological world. In alphabetical order the names are as follows: Frecheville-Prof. Wm. Frecheville, Professor of Mining in the Royal School of Mines, London; Past President of the Institution of Mining and Metallurgy. Garrison-Mr. F. Lynwood Garrison, Mining Engineer, Philadelphia, Pa. Harker-Dr. Alfred Harker, F. R. S., immediate Past President of the Geological Society of London.

Jan 6, 1918

By G. R. Palmer

The occurrence of mercury minerals in precious metal-bearing ores has long been noted. During cyanide leaching of these gold-silver ores, some mercury forms a soluble cyanide complex, which is present in the pregnant leach solution and passes through the process operations of the cyanidation mill. As a result, mercury is found on the electrowinning cell cathodes, on the stripped carbon before It is volatilized during carbon regeneration, or in theme tailings pond. The U.S. Department of the Interior's Bureau of Mines is examining the effectiveness of two ion-exchange resins to adsorb gold and/or mercury from a cyanide leach solution. The resins, Duolite A-7 and Ionac A-305, were contacted with leach solutions containing varying concentrations of mercury, gold, and silver. The resin A-7 reached a maximum mercury loading of 0.0165 lb Hg/ft3, and A-305 reached a maximum mercury capacity of greater than 0.44 lb Hg/ft3. Adsorption of gold by both A-7 and A-305 is influenced by the presence of additional ions in the solution.

Jan 1, 1984

By J. M. Johns

INTRODUCTION The Climax Mine is located on the continen¬tal divide, on Fremont Pass, about 145 Km south west of Denver, Colorado. Molybdenum, along with the by products, tungsten, tin, and pyrite are produced from both the open pit and under¬ground operations. The underground operation utilizes a panel caving mining system, and produces in excess of 27,000 mt per day. In the mid 1930's, the Climax mine began changing from a grizzly level layout to the slusher drift system which is still in use to¬ day. Over the years, the slusher drift layout has been refined to correct, improve, and sim¬plify minor operational problems. In common with most older hardrock mines, the development equipment used at Climax was the standard rail mounted, pneumatic mining machinery. This type of equipment remained in use, at least to some degree, until about four years ago. For production, 112 Kw electric slushers were used, while mine traffic was rail with trolley locomotives. Beginning about ten years ago, Climax began

Jan 1, 1981

By Cyril Smith

SOMEWHAT over ten years ago the author described studies1,2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase bound-ary was accepted as substantially correct, even by later investigators3,4 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems" without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese¬silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced" to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polar-ized light and asserted that a new phase, not cubic, should be placed in the diagram adjacent to alpha. Sautner,13 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his dia-gram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4

Jan 1, 1939

By Walter Hull Aldridge

Much has been said about the foreseeable exhaustion of known mineral reserves-particularly in the United States. It is claimed that we are about to become a have-not nation insofar as certain essential minerals are concerned; and in this respect our position is often contrasted with that of the world as a whole, largely because we have drawn so heavily on our domestic resources during the last fifty years. As a matter of fact, the difference is not great if one takes a reasonably long-term view of the situation. No one denies that nature endowed the United States richer in mineral resources than any other equal area. It is granted that we have skimmed the cream of many kinds of minerals; but in a free international trade in minerals it would not be many decades before the richer deposits-at least the deposits easy of discovery throughout the world would be depleted to much the same degree as those in the United States today. For it is a fact that the problem of satisfying the needs of our industrial society for minerals is fundamentally worldwide in scope. The singular and significant attribute to all minerals is that there is but a single crop. Forests can be grown, but mineral deposits can be replaced only by finding new ones. Thus, one of the vital tasks of the mining engineer, the petroleum engineer, and the geologist is to find these new mineral resources. Another task is to devise means and methods for the exploitation of, at costs that are economic, low-grade deposits and those deeply buried in the crust of the earth. The first need, however, is to find the deposits in the ground. If the assumptions of those who today fear an early exhaustion of all deposits are valid, the outlook for continued material and social progress is gloomy indeed. I take a more optimistic view, for it is my belief that vast new sources of needed minerals will have come to light before our known resources are gone. The real question is whether the outside layer of the crust of the earth that is accessible to engineers contains adequate mineral deposits; and whether engineers can find those deposits. The answer must be based on geologic science, geologic fact, and mining history. Every continent, and almost every country, has yielded minerals of industrial utility in substantial quantity. Mineral deposits are widespread. Geologists know the conditions that were favorable to the occurrence of ores and the types of rocks in which various kinds of ores may ordinarily be found. They know that such rocks occur over broad regions of the earth's surface. They also know that in large areas rocks that are potential carriers of ores are covered and concealed by material of entirely different character. Such cover may consist of lava flows, layers of volcanic ash, or beds of material washed down from the surrounding mountains. Sometimes those covers are thick, sometimes relatively thin. But men well-qualified to pass judgment are sure that concealed deposits, large in number and in size, exist close enough to the surface to make exploitation practical. Only by actual penetration of the surface can this contention be proved, but to conclude otherwise would be to ignore the laws of probability and to deny the over-all consistency of nature. The task of probing the crust of the earth to determine the location of these deposits, and to obtain some notion of their size and quality, poses serious problems. However, they should not be beyond human solution. Much more research must be done in analyzing and explaining the laws of ore deposition. New tools, in the shape of techniques and methods and of mechanical and electrical devices and instruments, must be developed. But no reasonable person can doubt that these objectives will be achieved. As the need becomes increasingly pressing, scientists and engineers will supply the imagination and the ingenuity that will provide the solution. The time and effort thus far devoted to the development of methods for locating hidden ore bodies have been pitifully meager. Energetic investigation of the subject of applied geophysics is essential to the success of the mineral industry, and I have no hesitation in predicting that effective techniques will be found and successfully applied. Twenty-five years ago the petroleum industry

Jan 3, 1950

By Matsubara, A.

THE problem of the equilibrium between iron, carbon, and oxygen was first carefully investigated by E. Baur and A. Glaessner,1 who determined the equilibrium conditions of the two reactions Fe304 + CO ? 3FeO + C02 (1) FeO + CO ? Fe + C02 (2) within the range of temperature of 350 to 900° C. The next series of investigations was made by R. Schenck and his co-workers,2 who sought to check the results of Baur and Glaessner's work within the range of 550° to 700° C. and to elucidate the conditions of formation of iron carbide. The equilibrium conditions at the higher temperatures, however, are generally understood to be much more complicated, owing chiefly to the formation of solid solutions between iron, its oxides, and carbide; nevertheless their determination is of much more practical importance than those at the lower temperatures. It is well known that each of the reactions is reversible; equilibrium is established when the partial pressure of oxygen in the gaseous phase has become equal to the dissociation pressure of magnetic oxide in equation 1 and that of ferrous oxide in equation 2. These equilibria are subsequently designated by "the Fe304-FeO equilibrium" and "the FeO-Fe equilibrium," respectively. As the Fe304-FeO equilibrium has three phases with three components, it must be bivariant. But the reaction involves no pressure change in the gaseous phase, hence the final composition of the latter is practically unaffected by pressure. To know, the equilibrium conditions, the compositions of the gaseous phase at different temperatures must be determined. At the higher temperature, however, iron and its oxides dissolve one another in various proportions forming solid solutions; in many cases the content of oxygen in the solid phase becomes a new independent variable.

Jan 2, 1921