Search Documents

By P. K. Foh, C. G. Dunn

IN an investigation of the rolling and recrystalliz-ing textures obtained from single crystals of Si-Fe, Koh and Dunn included specimens in the (111) [lie] orientation.1,2 This note reports some additional results obtained on samples of this orientation set aside for further study. After, primary recrystallization longer annealing treatments at 980°C produced only normal grain growth; after 16 hr at 980°C the largest grains were approximately 0.010 to 0.020 in. in diam. The orientations of 13 of the larger grains were found by the transmission Laue method. The unidentified (110) poles of these grains have been added to the (110) pole figure obtained after primary recrystallization2 to give the plot shown in Fig. 1. When grain identifications are also included, such a plot reveals the following. Two orientations agree almost exactly with the peak pole ,density positions of component B of the primary recrystallization texture, one with component A, and one with component C. All the remaining orientations except one have (110) poles near weaker and unidentified pole density peaks. In fact, the correlation is good enough for an identification of eight components. Previously only components A, B, and C were certain. The results are perhaps even more informative when combined with the (110) pole figure of the cold-rolled crystal to give the plot shown in Fig. 2. Each of the 13 orientations is identified and uniquely determined by selecting two (110) poles per crystal, which are 90" apart. The plot shows that every grain of the 13, except grain 6, has a (110) pole in common with a (110) pole concentration of the cold-rolled crystal. The orientation relationship with the cold-rolled orientation may be expressed as approximately 25" rotations about <110> axes, which is in agreement with the results found for coarse-grained primary recrystallization.2 If primary recrystallization had occurred according to the <110> rule without preference, there would have been 12 components. Actually our limited data reveals nine of the possible 12. The integrated pole figure also shows preferences among them, since three are considerably stronger than the rest. In addition to the above direct information, the following conclusions may be drawn. Primary recrystallization of the (111) [110] cold-rolled crystal produces a limited number of weak and strong components with the larger than average primary grains from these components related to the cold-rolled crystal by 25° <110> relationships. In arriving at this conclusion of limited orientations the (111) [110] orientation has to be ruled out as a source of large primaries for two reasons. First, growth in this orientation was not observed, despite an expected high grain boundary mobility (due to its 25" <110> relationship with every component of the texture). Secondly, primary recrystallization usually produces grains in new orientations, particularly in a single orientation matrix; but (111) [110] is not new. Other orientations besides those of the <110> type may be considered unlikely, of course, because the <110> relationship holds quite well for primary recrystallization2 and should produce the large primaries. There are exceptions to this rule, but probably not enough to provide large

Jan 1, 1958

By Frank E. Woolley, John F. Elliott

Mathematical models of the transient thermal behavior of a high-temperature solution calorimeter1-3 have been developed. The thermal behavior of the calorimeter is appoxirrzated by linear lumped-parameter models, and hence is described by sets of linear ordinary differential equations with constant coefficients The response of the models to various inputs is shown to agree with the response of the real system. Application of the modeling to experimental design and analysis of data illustrates the usefulness of simple models of complex systems. The early eperiments1,2 with the high-temperature solution calorimeter indicated that the change in the temperature of the bath resulting from the addition of a solute sample to the bath involved not only the direct effect due to the solution process but also possibly a secondary effect arising from the change in coupling between the bath and the induction heating coil. Consequently, an extensive analysis of the calorimeter was carried out, and models of the transient thermal processes of the instrument were developed to aid in improving the design and interpreting the behavior of the system. This paper describes the dynamic modeling; the use of it in treating experimental results has been reported earlier.3 The high-temperature solution calorimeter was constructed to measure directly the partial molar heats of solution of solute elements in a variety of liquid metal solvents.1-3 The calorimeter consists of an induction-heated liquid metal bath into which small samples of a solute element can be dropped. The bath temperature is recorded continuously, and the change in the measured bath temperature with time, dTm = f(t), resulting from the solute addition are the raw data from which the enthalpy change caused by the addition is determined. To extract the rmodynamic results from the data, the temperature change must be compared with that resulting from calibration additions of known enthalpy change. Accordingly, it is necessary to understand the transient thermal processes arising as a result of the addition to the bath. Neither modeling nor experimentation alone could provide the required insight into the working of the calorimeter. The alternate use of both methods in conjunction greatly assisted the design of the equipment and experiments, and the interpretation of the data. THE PHYSICAL CHARACTER OF THE SYSTEM The essential parts of the calorimeter, Fig. 1, for model studies are the thermocouple, the liquid metal bath and the surrounding refractories. The system is the solvent metal bath and those refractories around it which undergo a temperature change as a result of an addition to the bath, and which determine the way the temperature of the bath responds to an input. The inputs are the combined transient thermal effects arising when an addition is made to the bath. They include the thermal effects of the addition itself and the results of changed coupling between the bath and the induction coil. The response is the variation in the measured bath temperature, dTm(t) = Tm(t) - Tm(O), from an initial steady state resulting from the inputs. It was assumed in this study that the physical properties of the various elements of the system are independent of the inputs and time, although these properties may vary as the result of changes in the composition and size of the bath during a series of additions. This separation of inputs and the system is equivalent to assuming that the system is linear, i.e., that its behavior can be described by linear differential equations with constant coefficients. Linear behavior can be expected whenever the departure of each portion of the system from its steady-state condition is small enough to cause negligible changes in the thermal properties of the materials and in the various heat-transfer coefficients. Radiative heat transfer is important in this system, so the assumption of linearity should be valid only for small temperature deviations. Several conclusions were drawn from operation of the calorimeter in earlier experimental studies: 1) Radiative heat transport from the top of the bath is a significant portion of the total heat lost from the bath. However, for small changes in the bath temperature the change in transport by this path could be assumed to be proportional to the change in the bath temperature. 2) A very small portion of the heat input is lost through the thermocouple to its water-cooled holder. The thermal resistance and thermal capacity of the thermocouple protection tube are small, so the temperature of the thermocouple should follow closely that of the bath. 3) The remainder of the total heat lost from the bath will pass by conduction through the crucible to, and through, the other refractories, eventually being absorbed by the water-cooled induction coil or by the water-cooled sides and bottom of the enclosure. 4) The thermal resistance between the bath and crucible is very small. Thus the thermal capacity of the crucible will affect the temperature of the bath very soon after an addition of heat to the bath. 5) The thermal resistance between the crucible and the silica sleeve is large, especially if a radiation shield is placed in the gap. The effect of the thermal capacity of the sleeve thus will be significant only at longer times. The thermal resistance through the packing below the crucible also is large, so the packing and the silica sleeve will have similar effects on the behavior of the system. 6) A large temperature drop exists across the gap containing the water-cooled induction coil. Thus for relatively small changes in the thermal input to the bath, the refractories beyond the sleeve

Jan 1, 1970

By Wilbur T. Stuart

TO assist the mining industry in attacking problems of water control, the U. S. Geological Survey has begun a program of research in mining hydrology. In certain fundamental respects water control is similar to development of water supplies from wells or to the drainage of agricultural lands, as many of the tools developed in recent years for quantitative ground-water problems are applicable, with modification, to mine-water problems. In 1952 a 30-day pumping test conducted jointly by the Eureka Corp. Ltd. and the Defense Minerals Exploration Agency provided an opportunity to gain knowledge concerning water movements around a flooded mine shaft. The methods of analyzing the data may be used as a guide for the evaluation of similar problems elsewhere. The Fad shaft of the Eureka Corp. is on Ruby Hill, 1 1/2 miles west of Eureka, Nev. The shaft was completed at a depth of 2465 ft in November 1947 at a site adjacent to the downfaulted block in which the ore was found. As the drift on the 2250 level progressed toward the ore zone, a large flow of water was encountered after the Martin fault was intersected. This flow exceeded the installed pump capacity, and an unsuccessful attempt to recover the shaft and the 2250 level was made in 1948.1, 2 Geology and Hydrology: The complex structure of Ruby Hill is that of an anticline broken first by thrust faulting and later by normal faults. The present orebody comprises several mineralized zones within a block of the Eldorado limestone of middle Cambrian age which was downfaulted 1400 to 1600 ft, and it may be related to a similar body mined at a higher level south of the Ruby Hill fault. At the depth of the largest zone of ore the block is roughly rectangular in shape, about 1000 ft wide and 1500 ft long, and dips about 30" NE, see Fig. 1. It is apparently bounded on the south by the Ruby Hill fault, on the east by the Jackson fault, on the north by the Martin fault, and the west by the Bowman fault. Within the block, but between the Ruby Hill and the Martin faults, are the Office and Adams Hills faults; west of the block and the Bowman fault are the Albion and Spring Valley faults. There are many conflicting reports concerning the water-yielding characteristics of the Eldorado limestone and the condition of the fault zones, that is, whether they are open or tight. However, the diamond-drill records indicate that open spaces as much as 2 or 3 ft across were encountered, and considerable cementing and lining of holes was necessary to maintain circulation of drilling fluid. There is also evidence that the Eldorado limestone was cavernous where it was mined in the early days south of the Ruby Hill fault. At the site of the Fad shaft the formations encountered from the surface down included the Pogonip limestone, Dunderberg shale, Hamburg limestone, and Secret Canyon shale. These formations did not yield large quantities of water to the shaft. The Pogonip limestone, which appears to be permeable and might yield water elsewhere, is above the water table in the vicinity of the shaft. The Secret Canyon shale, immediately overlying the Eldorado in some places but in most places separated from it by the Geddes limestone,3 is apparently tight and does not transmit water. During the 30-day test period the shale briefly confined the water in the underlying formations so that artesian conditions were observed in drillholes E and F, which are cased into the Eldorado limestone, whereas unconfined conditions were observed in drillholes B, C, and D, which were open to the shale. The Geddes limestone, which normally lies between the Secret Canyon shale and the Eldorado limestone, was not encountered in the Fad shaft. The Geddes, a flaggy, fractured limestone, is reported capable of yielding large volumes of water. Water stored in the interstices of this thin-bedded limestone within the Ruby Hill fault zone on the 1200 level of the Locan shaft drowned the pumps in 1923 when the Richmond-Eureka Mining Co. attempted to explore the area along the fault. Eldorado limestone was not encountered in the Fad shaft. In the ore-block area the Eldorado limestone was not entirely offset from other water-yielding formations by movement along the Bowman fault; therefore it may be hydraulically connected with the other formations. Adjacent to the Ruby Hill, Jackson, and Martin faults, the Eldorado lies in contact with other possible water-yielding formations. One of these, the Prospect Mountain quartzite, is separated from the Eldorado by thin, sheared, and broken beds of the Geddes within the Ruby Hill fault zone. A limited examination by the author of the Prospect Mountain quartzite in the Richmond mine at a higher level and south of the Ruby Hill fault indicates that the quartzite is poorly permeable. The monzonite mass south of the quartzite would be a further barrier to the flow of water. The poor permeability of this area is substantiated by records of levels at which water was encountered south of the Ruby Hill fault. In view of the normally low rate of ground-water recharge, if this desert area had been permeable, water levels could not have been maintained at altitudes of many hundred feet above the present water table west and north of Ruby Hill. Thus the ore-bearing block of Eldorado limestone is in contact with possible water-yielding rocks on at least two sides, and if the fault zones are possible conduits for water circulation the geologic and hydrologic conditions are suitable for the infinite-aquifer type of analysis as used and modified here. History of Pumping: During sinking of the Fad shaft a maximum pumping rate of 1500 gpm kept the shaft dewatered sufficiently, but in March 1948, after the 2250 level drift passed through the Martin fault into the Eldorado limestone, the pumps and shaft were flooded. Subsequently additional pump-

Jan 1, 1956

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.&apos; It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method&apos; of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author&apos;s results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By D. Turnbull, R. E. Cech

EXPERIMENTAL studies of precipitation of iron from solid solution in copper by Gordon and Cohen 1, Bitter and Kaufmann 2 and Smith 3 revealed that the precipitate particles were initially paramagnetic but could be changed to a ferromagnetic

Jan 1, 1955

By Sherwin Kelly

THE need for geophysicists to adopt a uniform mode of expressing the electrical resistivity of geological formations has been stressed by Dr. A. S. Eve.1 The present paper is to emphasize the point he raised, to bring the weight of disinterested authority to bear on the matter, and to urge the adoption henceforth, save in exceptional cases, of a standard expression for resistivity; all in the hope that the needed reform will thus actually be brought about. The general definition of the resistivity of a material is the resistance in ohms between two opposite faces of a unit cube of that, material. No account need be taken here of the cases in which the unit volume is not a cube, and the units of length and cross-section are different, encountered principally when dealing with metallic conductors such as wires. The idea of the resistance of a unit volume of earth or rock has found expres-sion in geophysical literature in a number of forms and with a variety of units. Fortunately, the metric system has been adhered to in most cases, so ordinarily the meter or the centimeter, usually the latter, has been the measure chosen. The resistivity is then the resistance of a cube of the given rock, or soil, one centimeter on, an edge. This is far from always being the same thing, however, as the resistance of a cubic centimeter. A long thin wire could contain a cubic centimeter and have a high resistance, whereas the same volume formed into a flat plate would have an entirely different, and quite low, resistance between faces. Con-sequently, it is not proper to express resistivity in ohms per cubic centi-meter, inch, etc., as has been done occasionally by .some writers. In an effort to emphasize the idea of cubic volume, some geophysicists, the writer among them, have used the phrase, ohms per centimeter cubed. This is a graphic way of picturing the measure, but is not in favor among highly qualified authorities. In this connection, an appeal was made to the U. S. Bureau of Standards for advice, and the Director, George K. Burgess, kindly replied in detail as to the practice adopted by his Bureau: ." . .&apos; such expressions as ohms per centimeter cubed&apos; or any similar expressions are objectionable, because they certainly carry the implica-tion that the resistivity is found by dividing ohms resistance by the volume in cubic centimeters." Actually, of course, resistivity is found

Jan 1, 1932

By G. Richards Gwinn

GRAPHITE is one of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world&apos;s high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. TYPES of GRAPHITE USED IN CRUCIBLES Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1945

By W. W. Mullins, F. A. Nichols

Solutions are developed, assuming surface diffusion and both internal and external volume diffusion, for the relaxation of bodies slightly perturbed from spherical and cylindrical geometries. Combined with those previously published for the nearly planar case, these results provide a means of gaging the relative contributions of the two diffusional proc-cesses in any given case. It is shown that in all sintering experiments to date, and probably in any attainable in practice, surface diffusion has played the dominant role, although most previous authors have assumed otherwise. It is also shown that surface diffusion predominates in normal field-emission tip blunting and also for the coalescence of gas bubbles introduced into metals by a bombardment. The surface-diffusion solutions for a perturbed sphere are combined with previous results for volume diffusion to show that the inclusion of interface diffusion permits considerably larger spheres to develop in diffusion-controlled precipitate growth before the onset of instability. A mechanism is also proposed for the spheroidization of precipitate platelets as well as rods. In a previous paper1 the relaxation of a nearly plane surface to flatness by the combined action of the transport processes of viscous flow, evaporation-condensation (in a closed system), volume diffusion, and surface diffusion has been analyzed under the assumption that all surface properties are independent of orientation. In this treatment, criteria were developed for deciding which process predominates, and solutions valid in the latter stages of the sintering of small wires and particles to a plane were obtained. A numerical solution, valid throughout the entire particle-sintering process for the case of surface diffusion, was subsequently obtained by the present authors.&apos; It was found that the analytic solution (which assumed small slopes everywhere) is accurate to within -10 pct when the maximum slope of the profile is less than 0.3; the wire-sintering problem has also been solved nu- merically for the case of surface diffusion and here again the results converge to the analytic small-slope solution at late stages of the process, the two solutions agreeing in this case to within 10 pct when the maximum slope of the profile is less than -0.6. The purpose of this paper is to extend the perturbation solutions to nearly spherical and nearly cylindrical geometries. We treat only the two principal diffusional processes, i.e., surface and volume, but for these geometries we discuss volume diffusion both inside and outside of the solid. Our results, when coupled with Mullins&apos; solutions1 for nearly planar surfaces, provide criteria for gaging the relative contributions of surface and volume diffusion to the over-all transport process in three basic geometries. A very interesting feature in the cylindrical case is the occurrence of instability for longitudinal perturbations with wavelengths greater than the cylindrical circumference, a classical result. This instability of the cylindrical surface is applied to give a quantitative explanation for the often-observed "erratic" pore closure in the late stages of the sintering of wire compacts; also, the theory previously presented for the spheroidization of rod-shaped precipitates by surface (interface) diffusion&apos; is expanded now to include volume diffusion inside and outside of the particle. The results for circumferential perturbations on a long cylinder allow quantitative estimates for gaging the relative importance of surface or volume diffusion in the early stages of the sintering of spheres or wires. The results here demonstrate clearly that surface diffusion has played a very important, if not dominant, role in all sintering experiments discussed in the literature, although the surface-diffusion contribution to the kinetics has usually been ignored. The results for the sphere (surface-diffusion case) are added to the results obtained previously by Mullins and sekerka3 concerning instabilities of a growing spherical precipitate particle (with interface diffusion disallowed) to obtain a general solution to this problem including interface diffusion. The inclusion of interface diffusion is found to increase significantly the range of stability of a growing spherical precipitate for typical metallurgical cases. The following assumptions are made: (i) the initial surface lies everywhere near and has a slope differing only slightly from that of the reference

Jan 1, 1965

By U. F. Kocks

The flow stress in some latent slip systems of aluminum and silver crystals after various deformations in single slip was investigated by transverse compression and supplemented by experiments on overshoot of the compression axis and the stability of corner orientations. Work hardening was found to be remarkably isotropic, the ratio of the flow stress in the latent system to that in the primary system being between 1.0 and 1.3. The strain-rate dependence was not significantly larger in the latent system. This low anisotropy suggests that specific dislocation interactions are not the direct cause of work hardening. Either the obstacles are essentially impenetrable so that only their distance enters, or a fairly random distribution of dislocations of all systems is. in fact. formed during single slip. The latter seems to he excluded by the observations on the strain-mte dependence and on the amount of secondary strain. The amount of seconzdary strains occurring in single slip was determined by shape-change mensurements and by a new method connected with the latent-hardening experiments. It is definitely less than 1/300 times the strain in the primary svstem. WORK hardening is due to dislocation interactions; this is a hypothesis, and possibly the only one, on which all present work-harden ing theories agree. About a dozen specific interactions have been considered, and it is unlikely that any essential one has been missed. Different work-hardening theories differ to a large extent in the specific interactions which are deemed most important. The presence or absence of any particular interaction, and its degree, depend on the geometrical relationships between the two dislocations interacting. Let us enumerate some examples. Two dislocations may react, with a varying reaction energy, to form a third dislocation, and this reaction product may be sessile or glissile. Two dislocations may intersect and a jog may be formed on both, on one of them, or on neither; this jog may be sessile17Z or glissile and it may, if moved nonconservatively, lead to the production of vacancies or interstitials. Finally, a dislocation may bypass another one and thus interact only with its stress field. All these interactions depend on the specific relation between the Burgers vectors and line directions of the two dislocations. Any dislocation generated during plastic deformation of fcc crystals belongs to one of twelve slip systems. Taking any one dislocation, its relationship to each of the other eleven can fall, by symmetry, into one of only five classes. These relationships are enumerated in Fig. 1 and Table I. Each slip system is represented in the stereo-graphic projection by two triangles, namely those in one of which the specimen axis would have to lie if the specimen were to deform in single slip on this slip system in a given sense, in a tension test. Let us represent the primary slip system by the shaded triangles. The other slip systems are classified only with respect to their relationship to this primary system. The code letters (initials of established names* in German) are explained in Table I. Three specific interactions are also listed in cases where they may be strong: the product of a reaction, the formation of jogs in either system, and the elastic bypass stress. The last column relates to the types of experiments reported in this paper and summarizes their results. To decide experimentally between the relative importance of the various interactions one would like to produce a group of dislocations in one slip system and then measure the stress necessary to force another group of dislocations of a specific second system through them. Hopefully, one can produce the first set of dislocations by plastically deforming the specimen in single slip. Then one can try to achieve single slip in a specific, previously latent system and measure its flow stress. If it is different from the virgin flow stress, there has been "latent hardening". Some types of latent-hardening experiments will be discussed in the next section. The strain-rate and temperature dependence of the flow stress is an indication of the importance of dislocation intersections. By extending an investigation of this dependence to the latent systems, one can determine how much more important forest contributions are here. seeger3 has used the as-

Jan 1, 1964

By Kenneth A. Moon

An exact statistical treatment of a one-dimensional model is used as a basis for evoluating the reliability of certain simplified expressions for the activity of the solute in interstitial solutions, including one obtained from the exact expression by setting the repulsive interaction equal to infinity. The latter approximation is found to be satisfactory at low and moderate concentration if the repulsive interaction is large, even though not infinite. A similar expression (identical if the co-odination number is two) is derived from the quasichemical expression of Lacher, and is recommended as the best available expression for the excess configurational entropy of interstitial solutions with excluded sites. Some reasonable models are discussed, and the nature of the saturated solutions is determined by inspection. Some of the models reduce to the one -dimensional case. An analysis is given of the excess partial entropy of hydrogen in V-H; Nb-H; and To-H solutions. MOST treatments of the statistical thermodynamics of interstitial solid solutions have followed the classic paper1 of Lacher in making the simplifying assumption that the configurational entropy of the solution is ideal. However, it is becoming increasingly apparent that there are many interstitial solutions with very large so lute-solute repulsions, and for these the assumption of ideal entropy is not valid or useful. It is important to realize that with substitutional solutions large repulsions between the component atoms must lead to phase separation, whereas in interstitial solutions the free energy of the solution is not drastically increased by large solute-solute repulsions until intrinsic saturation is reached at the concentration where further solute would be forced to enter a site in which it would experience the repulsive effect of one or more solute atoms already present. In the limiting case of an infinitely large repulsive interaction, the excess free energy would be attributable entirely to excess entropy, the enthalpy of mixing being zero. AS will be shown below, even if the repulsions are less than infinite, a treatment based on an assumption of infinite repulsions may be very satisfactory up to moderately high concentrations of the interstitial component. Often in solutions where large repulsive interactions exist, there are also small interactions — often attractive—between solute atoms in configurations other than that corresponding to the large repulsion. In such cases the excess free energy will consist of an excess entropy term attributable to the large repulsive interactions, and an enthalpy term corresponding to the other small interactions. Nomenclature to differentiate succinctly between important cases would be a convenience. In this paper the nomenclature shown in Table I will be used. In Table I, and in the preceeding discussion, excess quantities are defined in terms of standard states which are pure solid solvent and pure (possibly hypothetical) solid saturated phase of the structure in question. In practice, it is more convenient to choose the interstitial element as a component, and its conventional standard state. This will add a composition-independent term to the excess entropy and the enthalpy. The earliest paper known to the present author which treats the thermodynamics of athermal interstitial solutions was given by schei12 in 1951, but the statistical derivations in that paper are open to criticism. Speiser and Spretnak were the first to give a correct statistical treatment,3 limited, however, to concentrations sufficiently low that the number of empty sites excluded from occupancy by more than one filled site is negligible. The purpose of the present paper is to extend the statistical treatment to more concentrated solutions, and to examine the magnitude of the errors introduced by assuming that the repulsive interactions are infinite when in fact they must be finite. THE QUASICHEMICAL APPROXIMATION Fortunately, a standard method already exists for taking into account the effect of large interactions upon the entropy of mixing. This is the quasi-chemical method, in which the probability of existence of a given pair of solute atoms in a certain proximate configuration is assumed to be proportional to exp(-w/kT), where w is the energy increase of the solution when the two atoms are moved from isolated locations in the solution to the configuration in question. A quasichemical treatment of interstitial solutions was given in 1937 in a widely neglected paper by Lacher.4 The result comes out

Jan 1, 1963

By W. P. Sykes

SEVEN years ago, Dr. S. L. Hoyt1 presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned.

Jan 1, 1938

By Philip D. Pearson

CALAND Ore Co.&apos;s dredging program has reached the halfway mark. The goal is to remove more than 160 million cu yd of lake bottom material overlying the iron orebody in Falls Bay of Steep Rock Lake, Ont. Two large dredges were constructed to remove this overburden, a layer of soil about 90 pct varved clay some 400 ft thick. Moisture content of the clay is high-approximately at the liquid limit of the soil. A few years ago, searching for additional reserves of ore, Inland Steel Co. looked toward Canada and the newly developed Steep Rock iron range. To this end an option agreement was signed Dec. 30, 1949, between Steep Rock Mines Ltd. and Caland Ore Co. Ltd., a wholly owned subsidiary of Inland Steel. Several drilling programs were conducted between this date and Jan. 1, 1953, when a 99-year lease was signed covering an area of 1249 acres. This lease calls for ore production to begin in 1960, with full production of 3 million tons per year by 1969.

Jan 8, 1957

By AIME AIME

OCTOBER will be western month for the Institute. With meetings at Spokane, Tulsa, Los Angeles, and San Francisco, and with a large number of American Institute of Mining Engineers members and their families in the party sailing out through the Golden Gate to Japan on the afternoon of the tenth, the major activities of the Institute will, for this month at least, be west of the Mississippi. Despite cancellations due to necessity, most of the officers of the Institute will be present and taking part in some one or more of the Western meetings. Prof. Robert S. Richards, our senior past-president, will attend both the Spokane and San Francisco meetings and then go to Japan. President Bradley will preside at the San Francisco meeting and then head the party going to Tokyo. At Tulsa and Los Angeles, the principal officers of the Petroleum Division will be present and active and at all the meetings, directors, ex-directors and -present and past officers will be on the job and keeping things moving.

Jan 1, 1929

By Chauncey Berrien

THE Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth; while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit, for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper.

Jan 1, 1930

By C. D. King

DURING the 30-year period spanned by these annual Howe Memorial presentations, many lecturers could proudly claim a kinship either as a student or an associate of the man whose memory we honor. Although it has been my good fortune to have attended many of these annual lectures, it was not my privilege to have known Henry Marion Howe personally. However, his great repute as teacher and scientist was known to all undergraduates of my day and the later years have enhanced my appreciation of his wisdom and foresight. Those who knew him well have said he derived particular pleasure from speculations on the future world of metallurgy. For this reason, I feel that perhaps he would not be unsympathetic to a lecture in his honor which departs from the highly instructive scientific presentations made in the past by so many able Howe Memorial lecturers, and which is concerned more with the practical phases of various steelmak-ing processes and some speculations on their future form and relative importance. The word "revolutionary" is frequently applied to each seemingly important improvement in the production of steel ingots, but in retrospect these changes, impressive as they appear at the time, are merely steps of progress. In the hundred years from the inception of tonnage steelmaking, only three processes can be truly classified as revolutionary. They are the pneumatic process, known in this country as the bessemer process; the reverberatory method called the open hearth process; and, the electric furnace process. There have been many variations and combinations of the three fundamental methods, but they remain truly the only revolutionary methods in steelmaking since its early history. Everything else has been evolutionary, in effect. doing the same things that we have done in the past but doing them better, correcting our errors through experience, and slowly but inevitably reaching a higher state of accomplishment. It has often been said that coming events cast their shadows before, and the production of steel ingots is no exception. As a result of the unrelenting demands of World War I1 and the years that followed, truly impressive progress has been made in steel ingot production. The incessant pressure for immediate results during this period required the employment of initiative and daring, as in few past decades, and many developments were brought to fruition. Of equal importance is the possible effect on future steelmaking methods of the many ideas initiated but still in formative stages. Fig. 1 portrays ingot production in the United States by the three fundamental processes over a period of 75 years and is interesting because it poses some questions as to future trends. The early ascendancy of the bessemer, its replacement in importance by the open hearth process, the amazing growth of the latter, and the recent challenge of the electric furnace are evident from the chart. Management is fully aware of these changes, but is even more interested in the future trends. Our concepts of the relative importance of the more recent developments and their possible effect on future processes may perhaps be best exemplified by a specific, hypothetical problem. Let us assume management is contemplating a new ingot producing plant with an output of 100,000 net tons per month, located in an area where some purchased scrap may be obtained but where by far the largest component will be own-produced blast furnace iron. Management requires a process or combination of processes which will yield highly uniform quality characteristics in the ingot form, and represent the soundest selection in investment and operating cost. Under these conditions, the obvious selection for the past four decades has been the open hearth process but, in view of more recent developments, management may believe that it is no longer permissible to disregard other possibilities with impunity. Accordingly, to be assured of the best possible selection, they request that you review not only the possibilities of utilizing the conventional open hearth, duplex, bessemer, and electric furnace methods, but also the more recent developments, such as the turbo-hearth, the Linz-Donawitz method, the Perrin modifications, and other possibilities. With this background, one might then appraise the relative importance of these methods to meet a specific need, and concurrently speculate on the forms that future ingot processes will assume and the relative importance of these processes.

Jan 1, 1955

By Walter Mueller

Transition in the underground coal industry, begun with the passage of the Federal Coal Mine Health and Safety Act of 1969, should be completed midway in the 1972-80 period. Surprisingly, many of the far reaching effects of this act have been, for the most part, beneficial to the industry from the standpoint of health, safety and basic operating standards. Production has dwindled, but the next few years will see production declines level out. Average declines of approximately 27% have been recorded since passage of the 1969 act, with costs increasing an average of $1.50 per ton throughout the industry. Nationwide averages presently are in the range of 14 tons per man-shift, and by 1980 this may be further reduced to a 10-ton per man-shift average for the industry. But in spite of the many temporary set-backs affecting the industry, the marketing opportunities are clearly visible. Due primarily to the energy squeeze facing the U.S. over the near term, the &apos;underground coal operator is and will be enjoying unusual leverage in selling his product.

Jan 10, 1972

By J. W. Snavely

THE part that acceleration plays in starting a belt conveyor and its effect on belt conveyor design are well understood in a general way. Its practical importance is easily overlooked, however, and under some conditions, it is absolutely necessary to give the problem of acceleration detailed study. Most handbooks on conveyor belting design adequately present basic data for the determination of acceleration values. This paper will only attempt to present practical thinking and a convenient method of treatment of acceleration in belt conveyor design. Mathematical Analysis In working out the various problems of conveyor belt acceleration, the starting point, as presented by the handbooks, is the familiar formula of "force of acceleration is equal to the mass times acceleration." By expressing these fundamental quantities in terms of belt conveyor design, it is possible to arrive at the unsuspected conclusion that the acceleration time for horizontal belt conveyors is independent of the load, and instead, dependent upon the belt speed, the type of drive arrangement and drive pulley, and the idler coefficient of friction. The mathematics leading to this conclusion are shown in Table I, which has been prepared to show, this derivation. While at first the conclusion just given may not seem to be reasonable, further reflection indicates that obviously the type of drive pulley and the type of drive do affect materially the tension in the conveyor belt, and thus, as clearly shown, the time of acceleration is dependent upon the factors mentioned. Inasmuch as all of the factors except time are predetermined by the belt conveyor design, it becomes relatively easy to establish the accelerating time and to reduce further this time determination to a simple graph from which the time in seconds can be read directly. Such a graph is given in Fig. 1. The table appearing on Fig. 1 should be explained further. For a given belt speed, the time of acceleration can be expressed as a percentage of the belt speed. The time of acceleration is also dependent on the drive arrangement, and changes in the drive arrangement consequently change the time of acceleration. It further follows that for a given belt speed, the time expressed as a percentage of that belt speed also changes with the type of drive. Obviously then, it becomes possible to graph the percentage of speed for each type of drive against the belt speed and accelerating time, after which, for a given belt speed and type of drive, the time can be read directly in seconds. Two constants were established for Fig. 1, the first one being the limiting of the maximum acceleration tension to 35 pct of the full load operating tension in the belt. The purpose of this is to limit the total tension imposed upon the belt during the acceleration period to 135 pct of the full load operating tension, which is the amount required to start or breakaway the fully loaded belt conveyor from rest. The other constant is the friction factor used for the idler equipment, which has been established as 0.022. For installations where it is necessary to establish the values of acceleration, invariably high grade idler equipment is used, and it has been established from. field experience that 0.022 for the idler friction factor is amply conservative. The use of this friction factor for idlers must be tempered with judgment, of course, for occasions will arise where more power than indicated is required to start, even with the very best of equipment, such as low temperature operations that tend to congeal the grease in the bearings and thus produce additional friction drag. An inspection of the table in Fig. I affords a convenient rule of thumb method for determining the acceleration time, which conveniently can be 5 pct of the belt speed in seconds. The 5 pct of belt speed figure is close to the average for most types of drives. In using Fig. 1 it must be emphasized that it applies accurately to horizontal belt conveyors only.

Jan 1, 1952

By R. McNeill, D. E. Weiss, E. A. Swinton

In a continuous countercurrent exchange process, an alteration in any one of the operating conditions has a complex effect on the others, which can only be predicted by employing the transfer unit or the theoretical stage theory on a basis of trial and error. A simple method is described for illustrating diagrammatically the behavior of a counter-current system, the equations being simplified by means of a concept the maximum hypothetical exchange performance. An example based on a typical metallurgical system is given, in which a divalent metal is recovered from a dilute solution, the resin being regenerated continuously by a monovalent ion. Useful conclusions are drawn from a study of the theory. Practical methods for performing continuous ion exchange are discussed, and the development of equipment based on modified ore dressing jigs is described. A swinging sieve jig contactor is evaluated experimentally. DURING the last decade, the new synthetic ion exchange resins have been applied extensively in industries outside the field of water treatment, but there is no record of a continuous counter-current process operating on an industrial scale. Attempts have been made to devise a satisfactory process but many problems remain to be solved. The basic principles of continuous processes will be outlined, as well as the major problems in their operation and the progress made in the CSIRO laboratories toward the development of satisfactory industrial techniques. In the metallurgical field ion exchange resins can be used for various applications such as the recovery and concentration of valuable metals from mine waters,&apos; the regeneration of pickling and plating liquors," the prevention of pollution by waste effluents and the recovery of the constituents from them," and the purification of valuable metals such as the rare earths by chromatographic fractionation on columns of ion exchange resins.7,8 . Turther applications undoubtedly will be found in the field of hydrometallurgy where the use of ion exchange resins would enable direct extraction of the desired metal ion from the filtered leach liquor or the leach pulp. For example, an ion exchange process has been described recently for the extraction of gold from a cyanide leach pulp." A continuous process would have advantages in many applications over the usual process employing a fixed bed and intermittent cycle. In a recovery process, it would yield a product stream of steady purity and concentration, it would waste less water in rinsing, and if the contacting apparatus were efficient less resin would be used, since each portion of the resin would be cycled as soon as it was loaded instead of lying idle until the whole bed was ready for regeneration. A very major advantage is that it would be simpler to control automatically. It is probable that continuous operation will be the key for really large scale applications of ion exchange. The flow sheet of a continuous ion exchange recovery-concentration process is illustrated diagrammatically in Fig. 1. Dilute liquor containing the valuable ion flows through the stripping section countercurrently to a moving bed of resin and leaves after a final contact with freshly regenerated resin. The resin leaves the unit almost in equilibrium with the incoming liquor and then flows to the regenerating unit where it is treated by a slow countercurrent flow of concentrated regenerant solution. The adsorbed ion is displaced from the resin and appears in the concentrated product stream. The resin then must pass through a rinse unit or section where regenerant entrained by the resin is washed back into the regeneration section by water. The regenerated and washed resin is then recycled back to the stripping section. I. Theoretical Operating Behavior of Continuous Ion Exchange Stripping System The simple theory of continuous ion exchange is analogous to that of solvent extraction and other diffusional transfer operations and is governed by the equilibrium relationship, the mass balance, the rates of mass transfer, and the contacting efficiency of the unit. Equilibrium Relationship—The relative affinity of two ions A and B, for a particular resin immersed in their solution, can be expressed by plotting compositions of the solution against compositions which exist in resin in equilibrium with those solutions, i.e. C/Co vs q/a where C, is the total normality of the solution, C is the normality of ion A in the solution, a is the total exchange capacity of the resin in gram equivalents

Jan 1, 1956

By Jack C. Jones, Hemendra N. Kalia

This paper is partially based on a comprehensive ground control investigation that was conducted by Harza Engineering Company under a contract from the Bureau of Mines. This investigation required in- stalling several types of ground movement indicating devices on the surface and in the mine. The major instrumentation systems consisted of hydraulic borehole pressure cells, multi-point extensometers, in- clinometers, convergence indicators, Jack pressure recorders time domain reflectometers, and a 200 station subsidence network. The investigation demonstrated the versatility of the system. We were able to install pressure cell s to a depth of over 200 feet in the coal bed and we were successful in installing 10 pen mechanical recorders to monitor differential strata movement. In this paper, we have briefly discussed data from 18 borehole pres- sure cells, two time domain reflectometer cables and four subsidence lines. The data collected showed that the front and rear abutment pressures were approximate1 y 1000 feet (304.81~1) to 1200 feet (356.76111) from the active face. The peak pressure was about 4 times the over- burden pressure.

Jan 1, 1983

By F. Weinberg

Measurements have been made of solute segregation during dendrilic growth by using radioactive solute elements and ,measuring the activity of den(12-ites cut from decanted specimens. This has been done for both lead awl tin based binary alloys contaitzing the following solute additions: Ag, T1204, was dependet on ko, the equilibrium distribution coefficient in the following way Fay k &apos;c 0.1, C/C 0.6; for k0 >0.1. 0.6 <c,/c,< I. Qualitative obse?-vations were madc of dendritic segregation, by using autoradiographic techniques, for the Sn + Ag110 and Sn + Tlo4 systems. The observation were found to he in general agreement with the measurements ofCA/Co. Autoradiographic were also obtained of scctiolccl delzr11-iie stalks. These indicated that the stalks had a substructure, dclileated by solute corzetlt?atio?zs nlolg the substructure walls. A new dendrite growth direction <JI2> is reported for tila. SOLUTE segregation in dilute binary alloys has been investigated by Pfann,&apos; Smith, Tiller, and Rut-ter,&apos; and others. They considered the case of a slowly advancing plane solid interface, and derived expressions for the distribution of solute in both solid and liquid during solidification. To determine these expressions, they assumed no diffusion in the solid and either complete mixing in the liquid:&apos; or diffusion controlled solute movements in the liquid without any convective mixing.&apos; The present investigation considers solute segregation during dendritic growth, in which case the solid-liquid interface is not plane, and the growth rates are rapid. Segregation under these growth conditions has not been treated mathematically, because of the relative complexity of the system. It has been suggested by Chalmer, on the basis of preliminary results, that an alternative to the diffusion and heat flow controlled conditions during growth is &apos;diffusionless" dendritic growth in which solid is formed with the same composition as the liquid. He suggests this type of growth may depend upon a solvent-solute relationship that permits some solid solubility without excessive increase in internal energy, as is the case for solutions of tin in lead. On the other hand, Montariol,4 and others, have shown experimentally that some segregation does occur during dendritic growth in metals using etching and radioactive tracer techniques to indicate the concentrations of the solute. The present investigation was undertaken to determine, both qualitatively and quantitatively, the extent of solute segregation associated with dendritic growth in a series of binary alloys, as a function of solute concentration. PROCEDURE The solvent materials used were Vulcan Electrolytic tin (99.997 pct purity) and Tadanac lead (99.998 pct purity). The solute materials were Zn, Sn, and Sb (better than 99.998 pct purity), Ag and Co (99.5 pct purity), and T1 (Fisher "purified" metal sticks). Activation of the solute metals was carried out in the reactor at Chalk River, Canada. Master alloys were prepared by induction heating from the radioactive solute metal and the pure solvent, under argon, in graphite crucibles. Pieces of these alloys were then added to the solvent to give the required solute concentration. Dendrites were grown in essentially the same manner as that described by Weinberg and Chalmer, , in which controlled orientation single crystals were grown dendritically in horizontal graphite boats, and the liquid decanted. The crystals were grown and decanted in an atmosphere of tank argon. Before decanting, a sample of the liquid was drawn up in a glass tube and allowed to solidify rapidly. The orientations of the single crystals were such that <loo> was parallel to the growth direction, and (100) in the horizontal plane for lead, and [1101 and (110) respectively for tin. With these orientations long dendrite stalks formed along the bottom of the boat in the dendrite direction (<100> for lead and [I101 for tin) from which secondary branches grew. Only these secondary branches, which grew freely in the liquid from the dendrite stalk to the liquid surface, were used in the measurements. Accordingly, effects due to substrates and oxides on the surface of the liquid need not be considered. In order to measure the solute concentration C, of the dendrites, individual dendrite stalks were cut from the decanted specimens, remelted, and formed

Jan 1, 1962