Search Documents

By K. L. Komarek, P. F. J. Landler

Synthetic polycrystals of wustite were reduced ilz H2-H2O mixtures over limited roncentration ranges wiltun the wustite. field and the weight changes were continuously followed with a McBain quartz spiral balance. The reduction was. found to be controlled by a combined surface plus solid-state diffusion reaction. The solid-state diffusion had an activation energy of 38 kcal. Self--diflusioities of iron decreased with itzcreasing vacancy concentration. The activation energy of. the surface reaction runs different tor- different samples. The surface reaction-rate constan increased with increasirzg vacancy concentration. THE reduction of the oxides of iron has been studied for many years. Edstroem' has summarized the early work and has provided much information on the reduction of magnetite and hematite by hydrogen and carbon monoxide. More recent summaries are those by smeltzer2 and Themelis and Gauvin.3 Most investigators have reported that the iron metal which forms the outer layer during gaseous reduction is rather porous. According to Kohl and Engel14 the formation of such a porous iron layer depends on the properties of the underlying wiistite layer, on the reaction of the gas with the wustite surface, and on the transport of matter through the wustite layer. McKewan, Quets, Wadsworth, and Lewis, and Knacke 10 have found that, if a porous iron layer is formed, a surface reaction between gas and wustite at the bottom of the pores controls the rate of reaction. Seth and ROSS 11 and Warner 12 have pointed out that the influence of the gaseous pore diffusion through the porous iron layer cannot be neglected. It has further been shown that the wiistite layer formed during reduction is dense and that transport of matter across the layer occurs only by solid-state diffusion of iron ions.13,14 The solid-state diffusion rates observed by Edstroem and Bitsianis 14 and the surface reaction rates observed by Quets eta1.' show that an interaction of the two steps in controlling the reaction rate has to be considered. In this investigation the reduction of wustite was studied with respect to the interaction of the two steps, isolated from any other effects, by reducing wustite within the wustite field from higher to lower oxygen concentrations with H2-H2O gas mixtures. A similar study with CO-CO2 mixtures has been performed by Levin and wagner.15 Fused synthetic wustite polycrystals were reduced in steps of 0.4 wt pct from 24.4 to 23.2 wt pct 0 and over a temperature range from 700" to 1050°C. A few tests were also conducted with reduction steps from 24.4 to 23.6 wt pct 0 and 24.5 to 23.2 wtpct0. The Fe-O phase diagram is shown in Fig. 1 where the composition of the gas phase in equilibrium with the condensed phases is plotted as pct H2 vs the temperature. A careful study of the literature led to the conclusion that the fully drawn equicomposition curves (in wt pct O) in the wustite field used by Edstroem 1,16 and other authors needed some correction. Based on results by Darken and Gurry17 (shown as open circles) and on some of our own data, four corrected curves for 23.2, 23.6, 24.0, and 24.4 wt pct O were calculated (drawn as dashed lines in Fig. 1) which should replace the fully drawn equicomposition curves. MATERIALS AND APPARATUS Materials and Specimen Preparation. Wustite was prepared from iron sulfate (Fisher Scientific Co., New York) which had a purity of over 99.92 pct, with small amounts of manganese, copper, and zinc adding up to 0.03 pct. From the aqueous solution iron oxalate was precipitated and decomposed to magnetite according to Economos. 18 The magnetite powder was pressed into cylinders and sintered in vacuum at 900°C for several hours. The sintered compacts were placed in a platinum crucible of 2.5 cm diam which was fitted into a high-purity alumina crucible and then inserted into the center of the graphite heating element of an electric resistance furnace.lg The furnace was evacuated to below 1 p Hg and the magnetite sample was slowly heated. The evolution of gases during heating deter-

Jan 1, 1967

By J. C. Rengel

Why and how the nuclear industry entered the electric power generation business is discussed in terms that nuclear energy was an undoubtedly additional energy resource and that it had promise of becoming a virtually inexhaustible generating power if breeder reactors could be devised. The growth of nuclear power, its total generation capacity, are related to the need of increasing energy requirements. The use of atomic energy for power generation will grow if it can compete economically with other fuels. The rate of growth, the time scale and direction of technical development is dependent on ore supplies. It is predicted that by 1980, 50% of all new power installations will be nuclear stations. INTRODUCTION Ten years ago, the nuclear industry was virtually unborn, the Atomic Energy Act of 1954 had just been signed, and peaceful applications of atomic power was little more than a phrase. Serious discussion of the practical application of nuclear energy to electric utility installations in the West was highly unlikely. The questions: Why and how did the nuclear industry enter the electric power generation business at all?; What is the predicted growth of nuclear power?; What technological changes do we predict?; How will the above changes affect the utilities? will in part be answered by this paper. WHY NUCLEAR POWER? The only justification for the West as for any other section of the country for atomic power is economics. Whatever energy source will provide the lowest generation cost will prevail; the only electric utilities which have shown an interest in nuclear power are those to whom it means lower generation costs. It is true that the Government sponsored the development of this technology long before there was any evidence of better economics; but a Government must take a very long-range view and it is the only type of organization that can afford to look more than twenty or thirty years into the future. The Government looked at projections such as shown in Fig. 1, which shows various rates of energy consumption, and matched these against estimates of fossil fuel resources. This showed that we will exhaust our low-cost fossil fuel supplies within 75 to 100 years and our total known fuel supplies within 150 to 200 years. The decision to invest in nuclear energy rested, therefore, on two arguments: a) It was undoubtedly an additional energy resource; and b) It has promise of becoming a virtually inex-haustable resource if breeder reactors could be devised if, while generating power, the reactors would produce more fissile materials than they consumed. This decision produced an unexpected bonus: nuclear power became competitive with fossil power much earlier than had been expected and, as shown in Fig. 2, forced the coal industry to take a hard look at its own position. I believe that the drop of coal prices shown here is the direct result of the entry of nuclear power into the energy supply business. At this point, it ought to be explained why and under what conditions nuclear power can be cheaper than fossil power. Fossil fuel cost to the utility is composed of two factors: a) Mining; and b) Transportation. As a result, the cost of fossil fuel to the utilities varies from 126, 106 Btu to 306, 106 Btu and higher. Nuclear energy is highly concentrated and the transportation factor becomes insignificant. Today the cost of nuclear fuel to the utility ranges between 156

Jan 1, 1967

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965

Jan 1, 1949

By S. M. Brisbane

THE life of refractory linings in rotary cement kilns can be shortened by uneven or inadequate support of the kiln and its shell and by variations in the conditions of operation. Alteration of these factors may, according to their nature, bring about mechanical deterioration of the lining or promote chemical attack. Chemical attack has been described elsewhere.1-4 The distortion of cement kilns has been discussed in a general manner by Rochow,6 ho indicates the amount of distortion which may occur in an unlined shell, and by Rosenblad: who states that the deformations of the shell are greatest above the trunnions. The present article indicates the extent of the distortion of a kiln to an oval shape in certain selected positions and the deviation from a straight line of the kiln along its length between two supports. The cement kiln is a long, hollow, rotating cylinder consisting of steel plates which may be either welded or riveted together. This shell is supported on tires, frequently 60 ft apart, which roll on trunnions. The large mass of the kiln causes distortion of its cross-section; it becomes slightly oval, i.e., diameters lengthen as they become horizontal and shorten as they become vertical. There is also a tendency for the shell to bow between supporting tires; this bowing may be upwards or downwards depending on the position of the weight forces and the supports. The extent of the deviations from the ideal kiln shape was investigated. Observations described in this paper were made on the shell of the clinkering zone between the first and second tires of two of the kilns at the Geelong works of Australian Portland Cement Pty. Ltd. The kilns were both 400 ft long and 10 ft diam with a welded enlarged burning zone 11 ft 6 in. diam. The shell was fabricated from mild steel and in this section its thickness was 1 in. It was lined with 41/2 in. of chemically bonded magnesite-chrome bricks which were jointed with mild steel plates. The kilns operate on a 4 pct slope and the speed may be varied between 0.75 and 1.68 rpm. The wet process is used; kilns are coal fired and are fitted with integral coolers. Temperatures within the kiln are difficult to determine with any accuracy because of the absence of black body conditions, but surface temperatures are probably in the range 1420° to 1470°C. Average shell .temperatures at the two positions at which the deformation studies were made were 370°C and 355"C respectively. Methods: In determining the ellipticity it was necessary to measure the lengths of the vertical and horizontal diameters while the kiln was in operation; data obtained from a stationary kiln would not have the same practical significance. For this purpose the four points V, W, X, and Y at the ends of two mutually perpendicular diameters were marked on one kiln. The point X is shown in Fig. 1. For the measurement of the length of the vertical diameter a vertical column, to which a horizontally aligned telescope was attached, was placed 10 ft from the kiln. The telescope could be racked up and down in a vertical plane. Two sets of readings were taken, one set when each of the points V, W, X, and Y was at its maximum height above the

Jan 1, 1957

By Gerald C. Mathis

FERGUS County, Mont., shown in Fig. 1, is known for its once famous gold mines near the old towns of Gilt Edge, Maiden, and Kendall. But at Heath, a small farming community near the foothills of the Snowy Mountains, thousands of tons of gypsum have been mined since 1916. The value of the gold taken from the mines of Fergus County runs into millions of dollars; the value of the products made from the gypsum of the Heath mine is also in the millions. The gypsum mine will continue to produce for many years, while the gold mines are closed today. The Heath gypsum mine was developed by the Northwest Gypsum Co. in 1916. The products of the small mill built by this company were plaster, agricultural gypsum, and raw gypsum for cement manufacturing. The United States Gypsum Co. prospected the adjacent property in 1916 and 1917 by means of two adits and some exploration drill holes. During World War I, the company abandoned operations at Heath, but again became active in this area in 1928 hen it purchased all the property of the Northwest Gypsum Co. A long range program of expansion was begun with the building of a block plant and the purchase of additional land and mineral rights. A modern wall board plant was built in 1936. When the old wooden mill purchased from the Northwest Gypsum Co. burned in 1937, an all-metal calcining plant located at Blue Rapids, Kansas, was dismantled, moved to Heath, and erected on the site of the mill. In August 1951 a new mine was opened 3000 ft north of the mill. Rock is conveyed from the mine to the mill by an 18-in. belt conveyor. The Heath gypsum deposit lies at the base of the Ellis formation of Jurassic Age. The Ellis at Heath lies unconformably on the black fissle shale of the Heath formation of the Big Snowy Group, which is Mississippian in age. The strike of the gypsum bed is N45°E and the dip approximately 3" NW; the regional strike and dip of the area. The gypsum lies in a series of six layers separated from each other by thin seams of shale. The lower layer is composed of' gypsum and shale intermingled and is not of commercial grade. The upper five layers are high in purity, but only the middle four layers are mined on the advance, as the top layer is left for roof support. This top layer is mined on retreating operations at the same time the pillars are robbed. Total thickness of the gypsum layers varies from 12 to 14 ft. Fig. 2 shows the average thickness and arrangement of the layers. Mining Methods The mine was originally developed by driving an adit into the gypsum horizon. The Northwest Gypsum Co. mined in the top four layers, the top layer being split, leaving about 12 in. for roof support. A modified room and pillar method was used: entries were 15 ft wide and rooms varied between 20 and 30 ft and were turned on 90" from the entries. Crosscuts between the rooms left pillars from 10 to 20 ft square. The rock was loaded by hand into 1-ton mine cars and pulled to a central gathering point by mules; from the gathering point, mules or horses were used to pull the string of cars to the mill tipple. This method was continued by the United States Gypsum Co. from 1928 to 1937.

Jan 1, 1954

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

Notched and unnotched tensile specimens of wrought and recrystallized, oxygmted and hydro-genated tantalum and columbium were tested over a range of temperatures selected to encompass the ductile-to-brittle transition. Increasing the oxygen content of tantalum and columbium increased their strength, and raised their ductility transition temperature, but did not cause a marked deterioration of notch properties below that of commercially pure material. The adverse effects of oxygen were more pronounced for recrystallized structures than for wrought material. The effects of hydrogen are complicated by strain aging or slow strain rate hydrogen embrittlement at -105°F. However, in general, hydrogen had only a minor effect an strength, but markedly increased the effective transition tem-terature and caused a deterioration of notch properties . BCC metals including the refractory metals in Groups Va and VIa (V, Cb, Ta and Cr, Mo, W) can be expected to undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures.' Notch embrittlement is associated with this phenomenon, and can be a serious design problem. Table I compares the tensile transition behavior and notch sensitivity of commercially pure Group Va and VIa refractory metals. The Group VIa refractory metals have considerably higher transition temperatures, and become notch sensitive at higher temperatures, than do the Group Va refractory metals. In addition, the Group VIa refractory metals are sensitive to metallurgical structure. Recrystallized structures generally have higher transition temperatures than wrought material of the same composition. The relatively poor transition behavior of the recrystallized structures of these metals is generally attributed to the segregation of interstitial impurity atoms at grain boundaries. Pronounced sensitivity to structure is not evident with commercially pure Group Va refractory metals, however. Since these metals have higher solubilities for interstitial elements than do the Group VIa metals ,4 it can be expected that higher total interstitial concentrations are necessary to develop a comparable degree of grain boundary segregation and to produce a similar sensitivity of transition temperature to structure. Increasing only the concentration of interstitial atoms in solution would tend to increase the flow stress of a metal in relation to its cleavage fracture stress and thereby raise its transition temperature, but would not be expected to cause a marked sensitivity of transition temperature to structure. A research program has been conducted at the Battelle Memorial Institute to evaluate the effects of interstitial oxygen and hydrogen on the transition behavior and notch sensitivity of tantalum and columbium, and to evaluate the effects of structure on "contaminated" material. EXPERIMENTAL PROCEDURES Notched and unnotched tensile specimens of oxygenated and hydrogenated tantalum and columbium with both wrought and recrystallized structures were tested over a range of temperatures selected to encompass the ductile-to-brittle transition Oxygen levels selected for study in both tantalum and columbium were nominally 500 and 1000 ppm, whereas nominal hydrogen contents were 150 and 500 ppm in tantalum and 150 and 300 ppm in columbium. Oxygen and hydrogen additions were made directly to 6-in. lengths of 1/2-in.-diam electron beam melted wrought bar stock, in a Sieverts Apparatus. Subsequent high-temperature annealing was required for homogenization of the oxygenated material, but was not necessary in the case of hydrogenated stock. The oxygenated and hydrogenated bars were then swaged to 1/4-in.-diam rods. Tensile specimen blanks were cut from the 1/4-in.-diam rods and annealed to achieve stress-re-

Jan 1, 1963

By R. C. Hall

The magnetic anisotropy and magnetostriction of single crystals of alloys between 25 and 59 wt pct Co in Fe have been determined in the disordered and ordered states. The magrzetostriction is large and positive for all alloys in both states of order (up to 150 x 10-6 for A,, and 40 x 10-6 for 111). The magnetic anisotropy becomes zero rzear 41 pct Co for the disordered state. Ordering shifts the zero-anisotropy composition to about 50 pct Co. COBALT-iron alloys have for many years been of interest as magnetic materials because they have unusually high magnetic saturation values.' This interest was increased recently by the development of Supermendur.' Supermendur is an alloy of 49 pct Co-49 pct Fe-2 pct V* which was found by suitable purification and heat treatments, including a magnetic anneal, to possess excellent magnetic properties. These included a square hysteresis loop with a low coercive force and a high magnetization, and a low total loss. Two factors which are important in determining the magnetic hysteresis properties are the basic magnetic properties of magnetostriction and anisotropy. Alloys having zero anisotropy and zero magnetostriction show improved hysteresis properties.3 Since very meager data4-' are available in the literature on the single-crystal anisotropy and magnetostriction of the cobalt-iron alloys, the present program was undertaken to determine these two properties in the disordered and ordered states. EXPERIMENTAL TECHNIQUES Ingots of the cobalt-iron alloys containing from 25 pct to 59 pct Co in iron were vacuum melted from electrolytic iron and cobalt of 99.9 pct purity. The ingots were cooled at a rate of about 1°C per hr through the transformation temperature (950" to 980°C dependent on the alloy content) for the growth of large grains. From these grains, single-crystal disks were fabricated with either the (110) or (100) plane parallel to the faces of the disk. The crystals were given two heat treatments to produce either the ordered state (cooling rate of 20°C per hr from 850 "C) or the disordered state (water quench from 850 °C). Since the iron-cobalt alloys order very rapidly, the water quench may not have produced complete disorder in all cases. Due to the method of growth, the crystals were not perfect. Most of the samples had low-angle boundaries and a few had some small included grains. These imperfections could and probably did affect the accuracy of both the magnetic anisotropy and magnetostriction measurements. Much of the scatter in the data may be attributed to the crystal imperfections. The methods of determining the spontaneous saturation magnetostriction and the anisotropy have been previously described.419110 MAGNETOSTRICTION The magnetostriction in the [loo] and [Ill] directions (hO0 and ?111 respectively) is illustrated in Fig. 1 for the disordered state. Both ?100 and ?111i became large positive values as cobalt was added to iron. The state of order did not have a large effect on the magnetostriction. The effect of order did not appear too consistent in these data. Tentative curves are shown in Fig. 1 for the ordered magnetostriction near the FeCo composition; here ?100 appeared to be lowered and ?111 raised as the degree of order was increased. These results agree qualitatively with the

Jan 1, 1961

By D. D. Dunlop, J. R. Welker

The growing interest in the use of CO, in crude oil recovery increases the need for data on the effect of CO, on hydrocarbon physical properties. Data are presented on the solubility of CO, in various dead oils, the swelling changes in CO2-oil solutions and the effect of CO, on dead oil viscosity. This latter property shows the most pronounced effect, with viscosity reductions up to 98 per cent of the uncarbonated viscosities. An empirical method of estimating the viscosity of carbonated oils is presented. The apparatus and procedures used are described in sufficient detail to allow others to make similar studies. INTRODUCTION The effect of dissolved carbon dioxide on the swelling and viscosity reduction of specific hydrocarbon oils has been observed and recorded by a number of investigators.'- me object of this paper is to offer a means of predicting these effects for crude oils free from natural gas, using the dead state viscosity and gravity of the crude oils. The CO, solubility and swelling of numerous crude oils were determined in a visual cell at various pressure levels. The viscosity of the oils carbonated to various pressure levels was then determined by measuring the pressure drop across a capillary tube. From these data, the physical properties were correlated empirically. The resulting correlations allow the prediction of CO, solubility, swelling and viscosity reduction if the dead state gravity and viscosity of the oils are known. SOLUBILITY AND SWELLING MEASUREMENT EQUIPMENT AND PROCEDURE A high pressure visual cell was installed in a constant temperature cabinet. A test gauge was attached at the top of the cell for pressure measurement, and a line was run through the cabinet wall to a wet test meter which was used for volumetric measurement of the gas. The first step in making a test run was to put the oil in the cell up to a level about half to two-thirds of the total volume. This required about 50 to 65 ml of oil. carbon dioxide was then bubbled up through the oil for a time during which the pressure of CO2 in the cell was kept above 800 psia. Saturation of the oil with CO2 at this pressure and ambient temperature was confirmed by slowly bleeding CO2 through a valve to the atmosphere. If the oil was completely saturated with CO2, bubbles of gas would form in the oil at the first small decrease in pressure. If the oil was under-saturated, no bubbles formed until the pressure was decreased to the saturation pressure existing in the oil. If this saturation pressure was lower than that desired, more CO2 was bubbled through the oil until the desired level was reached. After saturation at ambient temperature was completed, the cabinet temperature was adjusted to the desired level and the cell was allowed to reach temperature equilibrium. After temperature equilibrium was reached, the pressure was again decreased slightly, and the oil again checked for full CO2 saturation at the cell pressure. The pressure now had changed because of the difference in solubility of the CO, in the oil at higher temperatures and the expansion of CO2 as the temperature increased. The outlet tube from the cell was then connected to the wet test meter and the CO2 was allowed to flow slowly out of the cell and through the wet test meter at ambient temperature and pressure. The water in the wet test meter had previously been saturated with CO2 at ambient temperature and pressure by allowing CO2 to flow continuously through it lor a period of several hours. The gas flow was stopped at several pressures during the run and the cell was allowed to come to equilibrium; this made possible the measurement of solubility and swelling data at the intermediate pressures. The volume of the oil in the cell was recorded at each of the equilibrium pressures in order to obtain swelling data. DATA AND RESULTS The solubility of CO2 in the oil was calculated by the relationship V — V, where R. = solubility of CO, in crude oil, cubic feet of CO, measured at 60F and 1.0 atm/ bbl of dead state oil at the temperature under which solubility was measured, V, = volume of gas released from the cell between the saturation pressure and zero pressure, corrected to 60F and 1.0 atm, cu ft, V, = volume of CO: contained in the gas space above the oil, corrected to 60F and 1.0 atm, cu ft, and V, = volume of the dead oil in the cell in bbl at the temperature of the run. The volumetric data of Sage and Lacey' were used to calculate V., from the volume of CO2 at high pressures. The swelling factor was calculated as where V, is the volume of the C0,-

By R. J. Charles

SEARCH for a consistent theory to explain the relationship between energy input and size reduction in a comminution process has accumulated, over the years, an enormous amount of plant and laboratory data. Although some correlation of these data has been possible for purposes of engineering design and for the advancement of research in fracture, there is still great need of a means of predicting behaviour of a solid when it is reduced in size by mechanical forces. The best known hypotheses proposed to describe the energy-size reduction relationships in crushing and grinding stem from a common origin. The present article analyzes problems of comminution in the light of the precepts of this origin. Its object is to reconcile points of difference between these well known hypotheses and to present relationships more widely applicable to comminution studies. Theoretical Considerations: Most existing relationships between energy and size reduction of a brittle solid stem from a single, simple, empirical proposition.&apos; Although this proposition can be demonstrated by observation and experiment, no theoretical derivation is yet possible. Mathematically, the proposition may be stated as follows: dE = -Cdx/xn [1] where dE = infinitesimal energy change, C = a constant, dx = infinitesimal size change, x = object size, and n = a constant. Eq. 1 states that the energy required to make a small change in the size of an object is proportional to the size change and inversely proportional to the object size to some power n. No stipulations are placed on the exponent n in either magnitude or sign. In 1867 Rittinger2 postulated that the energy required for size reduction of a solid would be proportional to the new surface area created during the size reduction. As far as can be determined there is as yet no physical basis for Rittinger&apos;s hypothesis. Rittinger&apos;s hypothesis can be stated mathematically as follows: E, = K(oa-a-0 . [2] Er = energy input per unit volume, K = a constant, <ti = initial specific surface, and o2 = final specific surface. In the size reduction of particles of size x, to particles of another smaller size, x2, Eq. 2 becomes the well known relation: ET = K&apos; {l/x2-l/xx) [3] where K&apos; is a constant. Eq. 3 may be arrived at from the proposition given in Eq. 1 by integrating and by assigning a value of 2 to the exponent n. J dE = J - C dx/x2 E = Kt (1x - 1x) where K&apos; = C. In 1885 Kick3 proposed the theory that equivalent amounts of energy should result in equivalent geometrical changes in the sizes of the pieces of a solid. For example, if one unit of energy reduced a number of equal-sized particles to particles of one half the size, then the same amount of energy applied to the particles resulting from the first test should result again in a size reduction of one half or a final size one quarter the original size. The Kick concept may be expressed as follows: Ek = K" log x1/x2 [41 K" = a constant and E, = energy per unit volume. The expression for Kick&apos;s law may be arrived at by again integrating Eq. 1 and in this case assigning a value of 1 to the exponent n. dE= J - C dx/x Eh = - C In {x/x2) = K" log (x,/x,) where K" = 2.3 C. Application of Kick&apos;s and Rittinger&apos;s laws to comminution has met with varied success. Gross and Zimmerley4 and Piret5 have shown that Rittinger&apos;s equation applies under certain conditions of experimentation. Walker and Shaw6 express the belief that in metal turning and shaping and in grinding of both metals and minerals the production of very fine particles (less than lP) follows Kick&apos;s hypothesis, whereas Rittinger&apos;s concept is valid for the size reduction of coarse particles. For the practical case of crushing and grinding, however, neither of the above hypotheses has received general acceptance. Bond&apos; has lately proposed that since neither Kick&apos;s nor Rittinger&apos;s hypotheses seem correct for plant design work, an energy-size reduction relationship somewhere between the two would be more applicable. The fundamental statement of Bond&apos;s work

Jan 1, 1958

By W. P. Evans, R. W. Buenneke

Warren and Averbach&apos;s multiple order, Fourier method was applied to solid specimens of SAE 1045 steel. The material was hardened to three hardness levels and specimens of each hardness were shot peened to three intensities. Particle size, root-mem-square strain, mean strain, md macro residual stress were determined for each. Microstrains caused by either hardening or peening varied markedly over microregions. In general, increasing the hardness or peening intensity increased the rms strain and decreased the particle size. Similar effects were observed by varying hardness and peening intensity independently. At a Rockwell hardness of C 50, peening had little effect on line broadening, but both mean strain and macro residual stress increased. Mean strain was independent of column length. Induced macro residual stress by peening was affected most by initial hardness, but not by specific peening intensity. The purpose of this work is to establish the state of residual strain and particle size by X-ray diffraction in hardened and cold-worked plain carbon steel and attempt to relate these X-ray measured parameters to fatigue performance. X-ray line broadening (and its micro implications), along with X-ray residual stress (and its macro implications), may be basic indicators of the inherent fatigue resistance of the material. X-ray line broadening is caused by variable lattice strains and small particle size. Both are a result of plastic deformation which accompanies hardening or cold working processes. Therefore, X-ray line broadening is a good measure of both. warren1 has recently reviewed the Warren and Averbach2,3 Fourier analysis of line broadening. Strain and particle size effects can be separated because broadening due to particle size is independent of order of the diffraction peaks, while broadening due to strain is not. Microstrain is obtained as a root-mean-square strain averaged over discrete distances within the crystals causing diffraction. These distances are quite small, varying from 10 to 10081, and may be interpreted as the gage length over which the strains are averaged. Because of their variable nature, the X-ray line is broadened. The plot of rms strain vs distance (or column length) within the specimen gives a measure of their variability. Small particles also cause X-ray line broadening as already mentioned. A particle is interpreted as a region within a crystal or grain which diffracts X-rays coherently. This region is one of given orientation and may be bounded by a small angle grain boundary, dislocations, a twin boundary, or a stacking fault. The present work covers measurement of X-ray line broadening and macro residual stress on an SAE 1045 steel, quenched and tempered to various hardnesses. Various amounts of cold working were produced by shot peening the surfaces to various Almen intensities. Particle size, root-mean-square strain, and mean strain were calculated from the Fourier coefficients of the X-ray diffraction profiles in a direction normal to the peened surface. No effort was made to separate the various causes of particle size broadening. Macro residual stresses were reported in directions parallel to the peened surface. I) X-RAY METHOD The Fourier coefficients were determined for the 110 and 220 X-ray profiles. They were corrected for instrumental broadening by the method of Stokes,4 using an annealed reference specimen of similar geometry presumed to be free from broadening due to small particles and distortions. The nth Fourier cosine coefficient, A,, is related to a particle size coefficient, Ap, and a distortional coefficient, ADn, by the equation:

Jan 1, 1963

By H. F. Mills

THE Iron King mine is 12 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped until 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of 140 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Denn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular, no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 8o ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 92o-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1947

R,. P. JaRvis,* El Oro, Estado de México, México.—The practical problem raised by Mr. Wisser—that is, the determination of the lower limit of ore deposition, below which it is useless to look for ore shoots—is one of the most important in economic geology. He asks: "Can we learn to determine the position of such a line?" For individual districts, yes; but its determination has always been by empirical methods; that is by actually exploring the veins to such depths that the values drop below the economic limits. Usually the signs are plain enough that values have been bottomed without confirmation by the chemist or assayer. Most veins, when approaching their limit, begin to split into branches or stringers; the vein matter itself undergoes a change from "lively looking" rock to one that is dull and unpromising, the quartz, instead of having segregated into clean vein matter, has simply spread itself into the country rock, rendering this more siliceous but no richer—these, together with inclusions of the country rock in the vein, are all positive indications of the limit. Mr. Wisser seems disposed not to accept the law of cause and effect, which he calls "empiricism." He says: "Empiricism embodies an assumption perhaps not evident at first glance. It is this: that like effects spring from like causes and therefore necessarily have a common meaning." There can be no doubt as to the validity of this law, since it is the foundation stone upon which are built all inductive sciences, including economic geology. When demonstrable, proved facts become confused with inferences, as they seem to be generally in the paper under examination, no sound conclusions can be reached. Mr. Wisser has failed to give sufficient data covering the two vein systems which he cites as examples. Presumably they are situated in the Pachuca District of Mexico, but not everybody is familiar with the vein systems there in spite of the fact that it is world famous as a silver producer. Are these two systems separated some distance horizontally from one another and how far? He has given no estimate of the amount and kind of rock that has been eroded from over the present veins. His description of the two systems appears on page 100, beginning: "1. East-west veins," and ends on page 101, "they would lack spaces there in which to deposit." On page 101, with the paragraph beginning "On the other hand," he gives a picture of what he believes takes place in class 2 veins. The sum of this seems to be, according to Mr. Wisser&apos;s observations, that, in the east-west veins, class 1, there has been an invasion of an "altering solution," which I judge has been responsible for the formation of extensive "alteration haloes"; that these alteration solutions have followed along pre-existing fractures or fissures; and that after these alteration solutions finished their work the mineralizing solutions deposited the vein matter and metallic values. Mr. Wisser does not specify clearly what the "alteration haloes" consist of; in other words, what change the original rock has suffered, whether oxidizing, carbonating, or sulphidizing. If they came from depth they could not be oxidizing or carbonating, and in this case it is a bit

Jan 1, 1941

R,. P. JaRvis,* El Oro, Estado de México, México.—The practical problem raised by Mr. Wisser—that is, the determination of the lower limit of ore deposition, below which it is useless to look for ore shoots—is one of the most important in economic geology. He asks: "Can we learn to determine the position of such a line?" For individual districts, yes; but its determination has always been by empirical methods; that is by actually exploring the veins to such depths that the values drop below the economic limits. Usually the signs are plain enough that values have been bottomed without confirmation by the chemist or assayer. Most veins, when approaching their limit, begin to split into branches or stringers; the vein matter itself undergoes a change from "lively looking" rock to one that is dull and unpromising, the quartz, instead of having segregated into clean vein matter, has simply spread itself into the country rock, rendering this more siliceous but no richer—these, together with inclusions of the country rock in the vein, are all positive indications of the limit. Mr. Wisser seems disposed not to accept the law of cause and effect, which he calls "empiricism." He says: "Empiricism embodies an assumption perhaps not evident at first glance. It is this: that like effects spring from like causes and therefore necessarily have a common meaning." There can be no doubt as to the validity of this law, since it is the foundation stone upon which are built all inductive sciences, including economic geology. When demonstrable, proved facts become confused with inferences, as they seem to be generally in the paper under examination, no sound conclusions can be reached. Mr. Wisser has failed to give sufficient data covering the two vein systems which he cites as examples. Presumably they are situated in the Pachuca District of Mexico, but not everybody is familiar with the vein systems there in spite of the fact that it is world famous as a silver producer. Are these two systems separated some distance horizontally from one another and how far? He has given no estimate of the amount and kind of rock that has been eroded from over the present veins. His description of the two systems appears on page 100, beginning: "1. East-west veins," and ends on page 101, "they would lack spaces there in which to deposit." On page 101, with the paragraph beginning "On the other hand," he gives a picture of what he believes takes place in class 2 veins. The sum of this seems to be, according to Mr. Wisser&apos;s observations, that, in the east-west veins, class 1, there has been an invasion of an "altering solution," which I judge has been responsible for the formation of extensive "alteration haloes"; that these alteration solutions have followed along pre-existing fractures or fissures; and that after these alteration solutions finished their work the mineralizing solutions deposited the vein matter and metallic values. Mr. Wisser does not specify clearly what the "alteration haloes" consist of; in other words, what change the original rock has suffered, whether oxidizing, carbonating, or sulphidizing. If they came from depth they could not be oxidizing or carbonating, and in this case it is a bit

Jan 1, 1941

INTRODUCTION Besides the European export credit agencies covered in Ted Rides&apos; paper in this Chapter, other agencies are also active (see Appendix) but the most notable for mining projects are The Export-Import Bank of the United States ("US Exim") and the Export Development Corporation ("EDC") of Canada. Mexico&apos;s Fomex is basically a short-term trade-finance fund administered by the Central Bank. US Exim This independent agency can provide loans, guarantees, and insurance. Like all export-credit agencies, its mandate is to support the export of goods and services from the US as a means of competing against other countries&apos; products. If a piece of mining equipment can only he made in the US, the US Exim may very well not provide any financial assistance. (It is important not to place the order for any item for which export credit is sought because, once ordered, the situation is no longer competitive in US Exim&apos;s eyes.) Direct Credits and financial guarantees ("buyer credits") are commonly in amounts greater than 85 million and for terms longer than six years. An example here is the $48.5 million provided to PT International Nickel Indonesia (see Robert de Gavre&apos;s paper in Chapter 12). US Exim usually requires a 15% downpayment and, therefore, finances up to 857 of the goods; less if the US content is lower. The dollar funding can he US prime, London Interbank Offered Rate (LIBOR), or other sources. Exim can fund in either or both of the following ways: 1. Under a US bank Letter of Credit ("L/C") 2. Reimbursement to the buyer/borrower via a US bank account. US Exim will, without charge, issue a preliminary commitment. It will, however, need to approve the various credit agreements and prefers to tie other parallel financings into one loan agreement. US Exim&apos;s total commitments are large, up to $5R billion in aggregate under various programs. US Exim has been the world&apos;s leader in medium-to long-term minerals project financings/ co-financings but suffers from (i) aggressive foreign export-credit competition whereby other nations mix in soft-loans or aid programs ("mixed credits") to increase the percentage financed and lower the interest margin and (ii) an imbalance in its own cost of funds. A common US Exim package would be as follows: 15% Banks under US Exim guarantee, floating rate over prime or LIBOR. 35% US Exim funding, fixed rate 35% Pefco funding, fixed rate 857 Drawn down pro-rata under US bank L/C 15% Cash down payment (may have been financed within a project/corporate credit) 100% Repayment usually begins six months after planned start-up in equal semi-annual instalments, with the banks usually paid out first, Pefco next, and US Exim last. Medium-term credits ("supplier credits") are issued for US equipment exports for terms up to five years, again for 85% of the equipment costs although the exporter is expected to bear at least 10% out of that 857 for its own risk. The buyer is required to be a first-class credit such as some governments or highly credit-worthy companies. Otherwise a bank L/C would be required. (This may be wrapped into an overall project-finance package for a minerals development. The project-finance banks provide an L/C to US Exim instead of funding that portion themselves.) US Exim guarantees 100% of the political risk and either 85% or 95% of the commercial risk for

Jan 1, 1985

W. H. SHOCKLEY, Chairman, FRANK H.-PROBERT, :Vice-Chairman, T. A. RICKARD, Sec.-Treas.; 420 Market St.,. San Francisco, Cal. C. C. BRAYTON, J. F. NEWSOM. A Meeting of the San Francisco Section was held on May 7, 1917. Chairman Shockley was in the Chair. The Section was honored by the presence of President Moore and Secretary Stoughton of the Institute. C. W. Merrill introduced President Moore, who then spoke to the Section on the Aims of the Institute. He discussed the possibility of improving the standards of membership by introducing a classification of membership. The present rigid investigation of applicants was pointed out by him. He spoke of the important influence that the local Sections can exert on the Institute and of the importance of sociability and informality at the meetings. Secretary Stoughton, who was introduced by the Chairman, emphasized somewhat the same points. He mentioned the need for making the Bulletin of the Institute more, interesting than it is at present, this to be accomplished by raising the necessary funds by increased advertising. He asked for an expression of opinion on this point. He. said that the employment department of the Institute is now used extensively. At the request of Mrs. Mark L. Requa, Mr. Stoughton. announced that a San Francisco branch of the Woman&apos;s Auxiliary of the, Institute was being formed and asked that the ladies of the members&apos; families send in their names to Mrs. Requa or to the Secretary of the Institute.

Jan 10, 1917

By R. W. Fountain, W. D. Forgeng

A new constitutional diagram is presented for the cobalt-rich end of the cobalt-titaniurn system. The modifications result from the presence of a new, intermediate, fcc phase, ?, the existence and homogeneity limits of which were established by metallo-graphic and X-ray studies of alloys containing from about 3 to 30 pct Ti. The precipitation of the ? phase from supersaturated solid solution was studied by hardness and electrical resistivity measzsrements, and two distinct stages in the process were observed. COBALT forms the base for a number of precipitation -hardenable alloy systems which may be divided into two distinct categories of practical interest, a) those hardened by intermetallic compounds and b) those hardened by carbide formation. The precipitation of intermetallic compounds from solid solution in cobalt-rich alloys has, however, received very little attention. Although the phase diagrams for some binary systems capable of precipitation have been determined,&apos; there is an almost complete lack of data on the property changes associated with the precipitation, and even less information on the kinetics of the reactions or morphology of the products. More information is available on the precipitation of carbides because of the practical significance in superalloys. A survey of cobalt binary phase diagrams suggested that the cobalt-titanium alloys might provide interesting and useful precipitation-hardenable alloys. The equilibrium diagram as proposed by Wallbaum2 is shown in Fig. 1. Köster and wagner3 have indicated that the maximum solubility of titanium in cobalt is about 10 pct at the eutectic temperature (1135oC), and this decreases to about 7.2 pct at room temperature. The temperature of the allotropic transformation in cobalt is lowered by the addition of titanium, about 5 pct being sufficient to retain the high-temperature fcc modification to room temperature. Wallbaum and Witte 4,5 have indicated that the precipitating phase in alloys containing up to about 29 pct Ti is Co2Ti, a hexagonal Laves phase of the MgNi, type. With slightly higher titanium contents, they also report a cubic modification of Co2Ti of the MgCu2-type Laves phase. Duwez and Taylor6 confirmed the existence of the hexagonal (MgNi2) modification but not the cubic (MgCuz) modification of Co2Ti and suggested that existence of the cubic form may have resulted from impurities in Wallbaum&apos;s alloys. In their work on Laves-type phases, Elliott and Rostoker 7 reported the cubic modification of Co,Ti, but did not confirm the existence of the hexagonal modification. However, Dwight8 in a discussion of the work of Eliott and Rostoker again showed the existence of both modifications of Co2Ti, a result which was confirmed at that time by Elliott and Rostoker. As a result of a study on the iron-cobalt-titanium system, Köster and Gellers suggested the existence of a Co3Ti phase isomorphous with Fe3Ti. Witte and Wallbaum,&apos; however, established the fact that no compound, Fe3Ti, exists in the iron-titanium system, and in a later publication, wallbaum2 stated that Kitster and Geller&apos;s reasoning was not valid, and no compound, Co3Ti, exists. This conclusion was later acknowledged by Köster.10 Preliminary experiments by the present authors to determine the precipitation-hardening characteristics of the cobalt-rich, cobalt-titanium alloys re-

Jan 1, 1960

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world&apos;s largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020&apos;s and low 0.030&apos;s; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman&apos;s viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world&apos;s largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020&apos;s and low 0.030&apos;s; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman&apos;s viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose moulding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956, p. 15). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat, abrasion, corrosion, and oxidation-resistant, and high strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, :hemica1 process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present economic-political conditions, he U.S. and for that matter, North America, has virtually insignificant ore reserves of chromite. There are chromite deposits, as will be described, but they would only be used under highly abnormal conditions if all outside sources were cut off. All chromite used in the U.S. is imported from the eastern hemisphere in which are contained the principal world reserves. As the main suppliers in 1971-72 were the USSR, Turkey, Republic of South Africa, Philippines, and Rhodesia, the strategic nature of chromite is obvious.

Jan 1, 1975