Search Documents

By R. J. Wagner, F. F. Craig, H. G. Riley, J. D. Griffith

Peripheral water injection has been underway in the Sholem Alechem Fault Block "A" Unit, Stephens County, Okla., since 1955. In the engineering planning of the flood, it was recognized that maintenance of pressure in the large, dry gas caps was vitally necessary to prevent the loss of an estimated 27 million bbl of oil through saturation of the gas caps by the oil banks moving updip on the peripheral flood pattern. The development of an abundant, low-cost water supply and the rising cost of makeup-gas purchases indicated that gas-cap control by water injection was desirable from an economic standpoint, provided an eflective water barrier could be placed without premature water breakthrough into downdip oil producers. A laboratory model scaled to the existing reservoir conditions was comtructed to evaluate the feasibility of gas-cap water injection. Model studies indicated that (I) water injected at the edge of the gar-oil contact would form a continuous barrier between the oil and gas zones, and (2) water would advance uniformly downdip without segregation due to gravity effects provided a specified, minimum water-injection rate was maintained. The model test results also indicated that it was not necessary to fill the gas cap completely with water. Water injection at the edge of one of the gas caps was initiated in March, 1958, to field test gas-cap water injection. Water breakthrough occurred at a downstruc-ture producing well in April, 1959, after approximately 2.5 million bbl of water had been injected into the gas cap. This was the volume calculated to be required to form the barrier between the oil zone and gas cap. This performance indicates that prevention of oil encroachment into dry gas caps in a peripheral water flood by water injection at the gas-oil contact appears practical and that the model studies provided a valid prediction of field performance. INTRODUCTION The Sholem Alechem Fault Block "A" Sims Sand Unit was one of the fist major waterflood projects in Oklahoma to utilize a peripheral injection pattern. Design of control measures to minimize oil encroachment into the large crestal gas caps was one of the greatest single problems during engineering planning of this flood. Engineering studies indicated that saturation of the gas caps with oil displaced by the peripheral water flood could result in a loss of about 27 million bbl of oil, or over one-half the estimated waterflood recovery. This estimate was based on a residual oil saturation after water flooding of 35 per cent pore volume, compared to the negligible oil saturation initially in the gas caps. The Sholem Alechem Springer field, located in Stephens County, Okla., is an elongated anticline with structural dips varying from 400 to 1,000 ft/mile. The structure contains numerous faults, some of which are sealing. The portion of the field considered in this paper is Fault Block "A", which is the largest of the five major fault segments in the field. A map of the unit is shown on Fig. 1. The unit is bounded on the east and west by major sealing faults, on the north by a water-oil contact and to the south by a deterioration of sand development. Two domes, each having gas caps, exist in the unit and are separated by a north-south fault as shown in Fig. 1. The sands being flooded are the Sims sand members of the Springer series of early Pennsylvanian age. The Sims sands average over 100 ft in thickness in Fault Block "A" and have a porosity of approximately 19 per cent. Core permeabilities average 160 md, with interstitial water saturation of about 23 per cent pore volume. Three different zones can be correlated over most of the area. However, they are commingled in most of the producing wells. The two upper zones, designated as First and Second Sims, are the most important. Both the First and Second Sims have gas caps in the east dome, while only the First Sims has a gas cap in the west dome. These gas caps, whose limits are also shown on Fig. 1, initially occupied nearly 11 per cent of the total reservoir volume. The major concern of this paper is the control of the two gas caps in the First Sims sand. Fig. 2 is a cross section, to scale, across the east dome of this formation. Notable features are the relatively shallow dip, the deterioration of the First Sims sand on the south side of the gas cap and the water-oil contact on the northern edge. The formation dip at the gas-oil contact in this cross section is approximately 5".

By J. L. Lehman, J. D. Sudbury, J. E. Landers, W. D. Greathouse

A full scale field experiment on cathodic protection of casing answers questions concerning (1) the proper criteria for determining current requirments, (2) the amount of protection provided by different currents, and (3) the transfer of current at the base of the surface pipe. Three dry holes in the Trico pool in Rooks County, Kans., were selected for cathodic protection tests. The three holes were in an area where casing failures opposite the Dakota water sand often accur in less than a year. Examination of the electric togs showed the wells to be similar to other wells in the field where casing in four of seven producing wells has failed. The three holes were cleaned out and cased with 75 joints of new 51/2-in. 14-tb J-55. Each joint was visually inspected and marked before it as run. The casing was bull plugged and floated in the hole 50 that the inside might remain dry and free of excessive attack. Also, if a leak occurred, a pressure increase could be observed on gawge at the surface. Extensive testing was done, including potential profiles, log current-potentid curves and electrode measurements from both surface and downhole connections. Based on these data, a current of 12 amps was applied to one well and 4 amps to mother. The third well was left to corrode. During the two-year period when the casing was in the ground, [he applied current was checked weekly, and reference electrode measurements were made about every two months. Three sets of casing potential profi1e.c were run. When the three strings were pulled, each joint was examined for type of scale formed, presence of sulfate-reducing bacteria, extent of corrosion nttnck and pit depth. Since the pipe was new when run, quantitative determination of the protection provided by current was possible. This is the first concrete field evidence to help resolve the many arguments about the proper method for selecting adequate current for cathodic protection of oilwell (-using. INTRODUCTION A casing string is run when a well is drilled. This pipe is supposed to protect this valuable "hole in the ground" for the life of the well. Often the casing does not last the life of the well; it is with these casing failures that this work is concerned. The cost of repairing a casing failure varies from field to field—from as much as a $30,000 per leak average in California to $5,000 per leak in Kansas. Additional costs other than actual repairs are also important. These include formation damage, lost production, etc. Casing damage caused by internal corrosion is important in some areas. Treatment normally consists of flushing inhibitor down the annulus, but further research is being done on control measures. The test described in this paper is concerned only with external corrosion. The problem of casing failure from external attack has appeared in several areas including western Kansas, California, Montana, Wyoming, Texas, Arkansas and Mississippi. Cathodic protection is currently being used in an attempt to control external corrosion. From reports in the NACE there are thousands of wells currently under cathodic protection. The quantity of current being applied ranges from 27 amps on some deep California wells to a few tenths of an amp being supplied from magnesium anodes on wells in Texas and Kansas. Considerable field and laboratory effort1,9,5,6 was exented on the problem of cathodic prctection of casing, and it became fairly obvious that this method could be used to protect wells. Early workers showed that current applied to a well distributed itself over the length of the casing and was not concentrated on the upper few hundred feet. Basic cathodic protection theory had shown that corrosion attack could be stopped by applying sufficient current. The problem resolved itself, then, into one of trying to decide just how much current was necessary. Various criteria were utilized in installing the many existing cathodic protection installations. These methods included the following. 1. Applying sufficient current to remove the anodic slope as shown by the potential profile." 7. Applying enough current to maintain all areas of the casing at a pipe-to-soil potential of .85 v.' 3. Applying the current indicated by a log current-potential (or E log I) curve." 4. Supplying the current necessary to shift the pipe to-soil potential .3 v." 5. Applying 2 or 3 milliamps of current per sq ft of casing."

By W. J. Slatosky

As a means of effecting better control of endpoint temperatirres at the Jones & Laughlin basic oxygen furnace plant, a set of mathematical equations has been developed. The eqlutions are the product of a themlochemical anaysis of the process and aye designed to calculate the required scrap, lime, and hot metal additions in terms of a number of independent variables. Results of test heats have warranted adoption of this technique by the Prodrrction Department. BECAUSE of the autogeneous nature of the basic oxygen steel-making process, bath temperature can be controlled without an external fuel supply by charging the furnace with additions that are thermally balanced. The thermal requirements of the charge materials are such that, during the refining process, they throttle the heat generated by the metallurgical reactions in a manner designed to result in a speci-fied temperature at the completion of the heat. In the past, operating personnel at the basic oxygen furnace plant of Jones & Laughlin's Aliquippa Works relied on their experience and technical knowledge of the process to determine the quantities of charge additions needed to result in a finishing temperature in the range 2880"to 2920" F. (The charge consists primarily of 93 tons of scrap and hot metal plus an amount of lime sufficient to maintain a basicity ratio of 2.8 to 3.2). Estimates of these materials are based on a consideration of the effects on finishing temperature of 1) iron silicon content, having a variation of 0.8 to 1.8 pct; 2) iron temperature, ranging from 2250°to 2600°F; and 3)any excessive cooling of the furnace due to a production delay. The end temperature of the preceding heat also serves as a guide in that, if a heat was within the specified temperature range, the succeeding heat could be charged with materials of nearly the same proportions, provided the hot metal used in each of the two charges was of approximately the same temperature and composition. On the other hand, if a heat was outside the specified tapping range, or if the hot metal used in that heat was of different analysis and temperature from that of the iron to be charged, an adjustment in the proportion of additions is in order for the following heat. Due to the complex thermochemical behavior of the process and to the inexact and subjective nature of the described method of determining charge additions, consistently accurate temperature control was not to be expected. Therefore, those heats out- side the specified tapping range necessitated subsequent adjustments by either reblowing the cold heats for a suitable length of time so as to elevate the bath temperature to the desired level, or cooling hot heats with a proper amount of scrap. Because extra time is required to make these adjustments, production is delayed. In an attempt to devise a method for improving temperature control, an analysis of the thermochemistry of the process was undertaken. This, in turn, led to the development of a set of mathematical equations which enable the calculation of the quantities of scrap, lime, and hot metal needed to result in any specified tapping temperature range. The analysis was not intended to be a repetition of work done by others such as McMulkinl or ~hilbrook.' It was meant to be an extension of their work so that charge additions could be calculated not in terms of silicon alone but, rather, as a function of all independent variables. This paper presents the derivation of these relationships, their effectiveness in controlling bath temperatures, and a method of utilizing them on an operational basis. The Heat Balance—The first step undertaken in the analysis of the problem was the enumeration of the pertinent variables. A list is presented in Table I where it is noticed that these quantities have been separated into the following three categories: important variables, variables considered as constants, and variables to be neglected. The breakdown was an arbitrary one designed to facilitate the analysis; otherwise, the mathematical treatment would have been exceedingly cumbersome and complex. Fortunately, experience has shown that these simplifying assumptions do not seriously impair the accuracy of the calculations. These variables along with the limiting assumptions listed in Table n were then used to write a heat balance of the process by applying the equation of continuity, Rate of Rate of Rate of Increase = Income - Outgo PI ] of Heat of Heat of Heat.

Jan 1, 1962

By L. R. Raymond, G. G. Binder

One primary purpose of hydraulic fracturing as a well stimulation technique is to overcome formation damage. The literature provides ways of designing fracture treatments and evaluating their results but not of incorporating formation damage in vertically fractured wells. Results of an investigation of this problem are presented in this paper. Prediction of stimulation ratios in vertically fractured, damaged wells is accomplished with a mathematical model relating stimulation ratio to relative conductivity of fractures whose lengths are not more than about half the drainage radius of the well. Comparison of results from the new model to results in published predictions verify its utility; these results also show that the range of stimulation ratios that can be predicted for undamaged wells is extended to include relative conductivities of less than 300. This extension is important when using fracturing to stimulate wells with high production rates and high native formation permeabilities. For example, large increases in daily oil production rate can be obtained with stimulation ratio increases as low as 1.25. The importance of complete fracture fill-up (uniform proppant packing) is shown through use of the mathematical model. If, at the mouth of a fracture, only a small fraction (1/2 percent) of the total fracture length is not packed with proppant, nearly all the polential stimulation increase is lost. Proppant crushing, compaction and embedment have been shown in laboratory studies to be responsible for low fracture conductivities in wells producing from highly stressed formations. Equipment and methods for testing the effect of stress (overburden) on conductivity of fructures in consolidated and unconsolidated sands are discussed in this paper. Laboratory tests with simlilated fractures in cores from both types of formations showed that crushing, compaction and embedment seriously affect conductivity. Results indicate that similar laboratory tests should be made when accurate knowledge of fracture conductivity is needed to assure good stimulation results for important wells. The chief factor in stimulation ratio reduction was found to be overburden pressure, but the size and type of proppant and the hardness of the formation have significant effects. Fracture conductivity reductions of up to 50 percent were observed with sand propping fractures in consolidated cores; a reduction of 83 percent was measured for an unconsolidated core. The range of effective overburden pressures for which conductivities were measured was from 100 to 5,000 psi. An example fracture design and evaluation problem indicates the usefulness of considering formation damage in planning well stimulation jobs. When damage exists, but its extent and the degree of permeability reduction are not estimated from diagnostic tests, the formation permeability used in planning the job may lead to under-designing. As the example shows, too low a target stimulation ratio can lead to much lower production rates (by half) than could be attained otherwise. Solutions of equations representing several special cases of the mathematical model are presented in graphical form and details of the derivations of the equations are given in the Appendix. INTRODUCTION Since its inception in 1947, hydraulic fracturing has proven to be an effective and widely accepted stimulation technique. In the past 18 years the ability to execute a successful hydraulic fracturing treatment has been substantially increased. The development of design and evaluation procedures1,2 has been one of the major contributions to this increased skill. However, as the art of hydraulic fracturing has moved closer to a science, new problems concerning the design and evaluation of the optimal hydraulic fracturing treatment have arisen. Three questions are pertinent to these problems. I. How is a fracturing job evaluated in a damaged well? 2. What is the effect on the stimulation ratio of not filling the fracture in the vicinity of the wellbore? 3. What is the effect of overburden pressure on fracture conductivity and, consequently, the stimulation ratio? A primary objective of fracturing a well is to stimulate production by overcoming wellbore damage. Presently. however, there is no rational basis for designing or evaluating the optimal fracturing treatment in a damaged well. All present fracture design and evaluation techniques assume that proppants can be uniformly placed in fractures. This assumption may be in serious error, particularly for the portion of a fracture directly adjacent to the wellbore. In this area, turbulence of the injected fluid can cause the proppant to be swept farther into the fracture. Also, loss of fluid from the fracture to the

By R. E. Ogilvie, N. L. Peterson

Diffi-lsion measurements were conducted at all compositims in the bcc solid solution of the U-Nb system employing incremental couples at composition intemals of 10 at. pct. Diffusion coefficients were determined by the Matano method from concentration gradients obtained with the electron-probe microanalyzer. The activation energy for inter-diffi-lsion as a function of compositim shows three distinct regions: 1) 80 to 100 pct U.6= 30 kcal per mole; 2) 20 to 80 pct U, $ - 70 kcal per mole; 3) Oto 20 pet U, Q = i40 kcal per mole. The frequency factor, fi0 and the activation energy $ were found to be roughly related by the following equation: log Do ^9.7 X IO-5Q -6,6. The Kirkendall marker movement indicates that DU is larger than DNb between 16 and 100 pct U and DNb is larger than DU from 0 to 4 pct U. FOR practical as well as fundamental reasons, the rates of diffusion in alloys are of considerable consequence. Most solid-state reactions are largely dependent upon the diffusion of atoms through the lattice structure and along grain boundaries. The high-temperature strength and reasonable nuclear properties of niobium have prompted its use as a reactor material in contact with uranium fuel. Hence, diffusion data for the U-Nb system are of considerable importance. In the previous diffusion study1 on the U-Nb system using pure element couples, reliable data were obtained only in the range of 0 to 10 at. pct Nb due to the large variance of the diffusion coefficient with composition. Also, a large Kirkendall effect and considerable porosity in the uranium-rich areas of the specimen were reported, which suggests that the true diffusion coefficients are somewhat larger. The purpose of the present study was to obtain reliable diffusion coefficients at all compositions using incremental diffusion couples with intervals of 10 at. pct. In view of the abnormal self-diffusion be- havior of y uranium2-4 and some other bcc transition elements,&apos;-&apos; it was felt that a comparison of the interdiffusion coefficients in the bcc U-Nb system with those of Reynolds et al.9 for the fcc gold-nickel system might shed some light on the diffusion mechanism involved. Both systems have similar phase diagrams, in that complete solid solubility exists above a miscibility gap. EXPERIMENTAL PROCEDURE The uranium used in this investigation was obtained through the courtesy of Argonne National Laboratory. An analysis of this material detected only Si-30, A1-7, C-6, N < 10 and 0-18 ppm. The niobium was electron-beam melted material obtained from Stauffer-Temescal. The gaseous impurities were less than 50 ppm, and the spec troc hemical analysis showed Ta-500 and W-200 ppm. U-Nb alloys were prepared at composition intervals of 10 at. pct by melting the appropriate amounts of the pure elements in an arc furnace. The buttons were inverted and remelted 6 times to assure complete mixing. The buttons were then wrapped in molybdenum foil, canned in Zircaloy-2 or stainless steel, and hot rolled 30 pct reduction in thickness at temperatures between 850" and 1100°C. Alloys with 10, 20, 30, 40, and 90 at. pct Nb rolled quite easily under these conditions, but the 50, 60, 70, and 80 pct alloys remained brittle. After melting and rolling (when possible), the alloys were annealed for 24 hr at a temperature within 100°C of their melting point in a dynamic vacuum of better than 4 x 10-8 mm Hg. These treatments produced alloys which were homogeneous on a 1 p scale within the detectability limits of the electron probe. During fabrication, the alloys picked up as much as 100 ppm Mo and 100 ppm Zr. Other elements checked for but not found were Co, Cr, Fe, Mn, Ni, and Ti. The grain size of the annealed samples ranged from 3 mm for the uranium-rich alloys to 0.3 mm for the niobium-rich alloys. This permitted measurements of the concentration gradients in the diffusion samples without crossing more than one or two grains, thereby eliminating any grain boundary effects. The specimens were bonded by theU&apos;picture frame" technique as reported by Kittel.10 Specimens of composition b)U + (100 - x)Nb were sandwiched between two specimens of composition (x + 10)U + (90 - x)Nb after they were ground flat and parallel

Jan 1, 1963

By J. W. Rutter, K. T. Aust

The migration of individual, large-angle grain boundaries has been studied as a function of tempereature and solute concentration in specimens of zone i.e filled lead containig very small additions of silver and of gold. Tile results are compared with various the-ories of grain boundary migration and with observations made prev.iorlsly of grain boundary migration in similar specimens of zone-refined lead containing tin additions. A previous investigation by the authors dealt with [he temperature dependence of grain boundary migration in bicrystals of zone-refined lead containing small additions of tin.&apos; It was shown that tin additions as low as a few parts per million cause a large decrease in the grain boundary migration rate at any given temperature, as well as a marked increase in the temperature dependence of the migration rate. It was found that existing theories of grain boundary migration. based on the motion of dislocations. or upon the concept of atom transfer in groups across the boundary (group process theory). or upon the control of grain boundary motion by volume diffusion of impurity atonls along with the boundary. are incapable of accounting for the observations. The single process theory of grain boundary migration. which is an absolute reaction rate calculation based on the transfer ui atoms singly across the moving boundary, was found to predict the migration rate reasonably well for a number of boundaries whose motion was shown to be very little influenced by impurities, but not for boundaries whose illation was influenced markedly by impurities. It was concluded that the elementary process of grain boundary migration involves the activation of single atoms during transfer across the boundary. and that inadequate knowledge is available to permit the influence of impurities to be properly taken into account. The present study was initiated to check the validity of the above conclusions with other alloy systems, namely high-purity lead with small additions of silver and of gold. Both silver and gold diffuse faster. and with a lower activation energy of volume diffusion. than does tin in lead;&apos; consequently, a study of the effects of silver and gold on grain boundary migration in high-purity lead offered a means of testing theories of boundary migration based on bulk diffusion of the solute (eg. ref. 3). In addition. it was hoped that the present work, in comparison with the results for tin in lead, would provide information concerning which factors are important in determin- ing the interaction between solute atoms and a grain boundary. EXPERIMENTAL PROCEDURE The preparation of bicrystals of zone-refined lead, with various silver or gold additions, was identical to that previously described for the lead-tin alloys.&apos;&apos;4 Each bicrystal consisted of a striated crystal which was grown from the melt. and an adjacent striation-free crystal which was introduced by artificial nucleation and growth.&apos;&apos;4 The striation or lineage substructure in the melt-grown crystal provided the driving force for grain boundary migration. During the preparation of striated single crystals by growth from the melt, it was found that silver or gold concentrations as low as 2 or 3 ppm by atoms were sufficient to cause formation of the hexagonal cell structure. which is due to the presence of impurity, during freezing. This structure is revealed on the solid-liquid interface by decanting the liquid during freezing. The hexagonal cell structure was observed previously4 in zone-refined lead crystals with tin contents above approximately 200 ppm by atoms. These concentrations of silver, gold, or tin are in agreement with the predicted amounts required for cell formation in lead,5&apos;6 under the present conditions of freezing.4 The absence of cell structure at decanted interfaces, therefore, served as a useful indication that the silver or gold contents were less than 2 or 3 ppm by atoms in the specimens as grown. It was found that grain boundary migration occurred only very slowly when the solute content approached that necessary for cell formation. As a result, the present experiments were conducted with silver or gold additions less than 1 ppm by atoms. This impurity level is well within the solid solubility limits for silver and gold in lead.7 The annealing treatments, measurements of grain boundary velocities, and orientation determinations were carried out as described previously.&apos; However. each bicrystal was also chemically polished in a solution consisting of 8 parts glacial acetic acid and 2

Jan 1, 1961

By C. Laird, C. E. Feltner

May different kinds of dislocation structures have been observed in strain-cycled metals and alloys. In order to understand their pattern and causes, an experimental program has been carried out to determine the influence on the dislocation structures of the three variables: 1) slip character of the material, 2) test temperature, and 3) strain amplitude. The results show that at high strain amplitudes cell structures me formed when the slip character is wavy, and that these are progressively replaced by uniform distributions of dislocations as the stacking fault energy is decreased. At lower strains, dislocation debris is formed which consists primarily of dipoles in wavy slip mode materials and multipoles in planar slip mode materials. Temperature merely acts to change the scale of the structure, smaller cells, and clumps of dislocation debris being associated with lower temperatures. It is shown that the results for many metals fit this pattern, which Parallels that occurring in unidirectional deformation. DISLOCATION structures produced by cyclic strain (fatigue) have been examined in a number of metals by transmission electron microscopy. These studies have produced a variety of interesting and often seemingly conflicting results. For example, different investigators have reported such structural features as cells.le4 bands of tangled dislocations,4&apos;5 dense patches or clusters of prismatic dislocation loops, planar arrays,4&apos;10 and various combinations or mixtures of these different structures. Most of these observations have been made on materials which were initially annealed and cyclically strained at low amplitudes resulting in long lives. Recently we have reported observations of the dislocation structures produced in copper and Cu-7.5 pct Al cycled at large amplitudes, resulting in lives of less than 104 cycles.4 These results, examined in combination with those in the literature, have suggested that a common or consistent structural pattern exists. Variations in this pattern appear to be determined chiefly by the three variables, namely, the slip character of the material,4,11 test temperature. and the strain amplitude. To verify this interpretation, we have studied [he influence of the above three variables (in different combinations) on the resultant structures in cyclically strained metals. Copper, fatigued at room temperature, was chosen as a reference state to which all other observations can be compared. The effect of slip character has been investigated by employing fcc metals of different stacking fault energy. Thus aluminum which has a more wavy slip character than copper, and Cu-2.5 pct A1 having a more planar slip char- acter, have been examined. The aluminum samples were fatigued at 210°K thus making their homologous temperature equal to that of copper at room temperature. The influence of temperature has been evaluated by examining the structures in copper at room temperature and 78°K. Finally the effect of strain amplitude was studied by looking at the structures at amplitudes giving lives ranging from 104 to 107 cycles. All of the specimens were examined at the 50 pct life level at which stage the structures have reached a stable configuration.12 I) EXPERIMENTAL PROCEDURE Strip specimens, 0.006 in. in thickness, were prepared from base elements of 99.99 pct purity or greater. Specimens were fatigued by cementing the strips to a lucite substrate which was subjected to reverse plane bending. This method of testing has been described e1sewhere.7 After fatiguing, specimens were thinned and examined in a Philips EM 200 which was equipped with a goniometer stage capable of ±30-deg tilt and 330-deg rotation of the specimen. On the basis of separate calibrations,13 allowances were made for the relative rotation and inversions between the bright-field images and the diffraction patterns. II) RESULTS AND DISCUSSION The life behavior of the materials under different test conditions is shown in Fig. 1 in the form of plots of total strain range vs cycles to failure. Comparisons of structures produced in the different materials were made at amplitudes which produced equal numbers of cycles to failure. The influence of strain amplitude on the structures produced in the reference state material (copper tested at room temperature) is shown in Fig. 2. At the 104 life level the structure produced comprises cells similar to those previously observed.3,4 They are approximately 0.5 p in diam and the cell walls are generally more regular or sharper than those produced by unidirectional deformation.14 At the 10&apos; life level the

Jan 1, 1969

By C. G. Dunn, J. L. Walter

Secondary recrystallization to the (110) [001] texture in high-purity silicon iron occurs if low-oxygen material is annealed in a nonoxidizing atmosphere. Any departure from these conditions results in a growth of (100) oriented grains. The nature of the matrix and secondary recrystallization structures and textures and the nature of grain boundary interactions during growth show that the low gas-metal interfacial energy of the (110) surfaces provides the driving force for growth of these grains. A type of grain growth, characterized by a driving force which derives from energy differences of {hkl} surfaces at the gas-metal interface, has been treated in recent papers.&apos;-7 Secondary recrystallization to the cube text!:: in high-purity silicon iron provides one example. The present paper also deals with a surface energy driving force but the texture that results by secondary recrystallization is not the cube texture; it is a texture in which the (110) plane is in the plane of rolling and the [001] direction is in the direction of rolling. The phenomenon described in this paper is different from the impurity (dispersed phase)-controlled secondary recrystallization process in which the (110) [001] oriented grains grow under the action of grain boundary driving forces.8-12 It is also different from tertiary recrystallization,2 which also produces the (110) [001] texture in high-purity silicon iron, since the matrix textures and grain sizes are different. Finally, it is unlike any other form of secondary recrystallization reported in the literature. The possibility of obtaining the (110) [001] texture in high-purity silicon iron became clear in a study of the effect of impurity atoms on the energy relationships of (100) and (110) surfaces. In this study Walter and Dunn6 observed the migration of (100)/(110) boundaries, i.e., boundaries between two grains, one of which has a (100) plane and the other a (110) plane, respectively, parallel to the plane of the sheet specimen. At 1200°C the (100)/(110) boundaries advanced into (100) grains in a vacuum anneal, then reversed their direction and migrated into (110) grains in a subsequent anneal in impure argon. Finally, the direction of migration reversed once again with (110) grains growing into (100) grains in a second vacuum anneal. These results were explained in terms of a change in concentration of oxygen atoms at the gas-metal interface during the anneals. Thus, oxygen atoms were added to the surface during the anneals in impure argon to the point where ?100, the specific surface energy of the (100) oriented grains, was lower than ?110, the surface energy of (110) oriented grains. In vacuum, however, the oxygen concentration at the surface was lowered to the point where ?110 < ?100. Concerning the possibility of secondary recrystallization in high-purity silicon iron with a low initial oxygen concentration, the observed effect of adsorbed oxygen atoms has indicated6 that a good vacuum anneal would favor the rapid growth of matrix grains with the (110) plane in the plane of the sheet much more than grains in the (100) orientation. The growth of only (110) oriented grains of course would depend upon y110 being less than ?hkl, where hkl refers to any plane different from (110). The present paper is concerned with the application of the above ideas to secondary recrystallization to the (110) [001] texture in high-purity silicon iron. The matrix and secondary recrystallization textures and structures are defined and discussed. Observations of growth of nuclei for secondary recrystallization and of boundary interactions are included to provide direct information on the surface energy relationships between (110) and other (hkl) surfaces. EXPERIMENTAL PROCEDURE As before, 2,4-6 high-purity iron and silicon were melted and cast in vacuum to provide an alloy containing 3 pct Si with less than 0.005 wt pct impurities. The oxygen content of the ingot was lower than in previous ingots, being approximately 3 ppm (by weight). The carbon content of this ingot may have been slightly higher than was found for previous ingots. The same rolling and annealing schedule used previously2 was followed in this study to obtain samples 0.012 in. (0.3 mm) thick. These samples were electropolished prior to annealing. After rolling and polishing, the oxygen content of the material was approximately 6 ppm; material used in the previous studies contained about twice this amount of oxygen.

Jan 1, 1961

By K. G. Davis

Dilute alloys of silver and of thallium in tin have been solidijzed unidirectionally under controlled conditions, to study the segregation associated with a cellular interface under conditions where both thermal and solute convection are present. Autoradiography and radioactive tracer counting techniques were combined with electron-probe microanalysis to study both macro- and microsegregation. It was found that, for concentrations giving only small amounts of constitutional supercooling, cell formation had little effect on the macroscopic distribution of solute along the specimen. At higher concentrations the effective distribution coefficient was higher than that expected for a smooth interface. Node spacing was independent of initial solute content at lower concentrations, becoming greater as keff increased. Silver content at the segregation nodes of silver in tin alloys was independent of initial concentration and considerably in excess of the eutectic composition. SINCE the investigation of cell formation at advancing solid-liquid interfaces by Rutter and Chalmers,&apos; a large volume of work has been dedicated to the determination of solidification conditions under which a planar interface will break down into cellular form. Early experiments were explained satisfactorily by the concept of constitutional supercooling,2 but, due to poor measurement of temperature gradients in the liquid, lack of accurate data on liquid diffusion and equilibrium distribution coefficients, and uncertainty about the effects of thermal and solute convection, these experiments cannot be used as proof for the theory. More recent work, however, has shown that under conditions where convection is eliminated or can be ignored good correlation is observed.3,4 Investigations into segregation at cell caps5 and at cell nodes6-&apos;&apos; have been made, but no measurements appear to have been done on the overall, macroscopic segregation down a unidirectionally solidified rod of material which has solidified with a cellular substructure. This has practical importance in casting, where regions of material with cellular substructure are often encountered, and also in zone refining where the thermal conditions necessary for a planar interface are unattainable. Further, as will be shown, the macroscopic segregation can give information on the following question. Granted that a cellular solid-liquid interface develops from a planar one when the conditions for constitutional supercooling are exceeded, how much supercooling is present after the cells have formed? EXPERIMENTAL PROCEDURE AND RESULTS Specimen Preparation. Specimens 25 cm long with a square cross section 0.6 by 0.6 cm were grown in graphite boats by solidification from one end. Alloy compositions are given in Table I. Two specimens of each composition were grown. The tin was 5-9 grade and the silver and thallium both 4-9 grade. Ag110 and Tl204 were used as tracers. Each composition had the same quantity of tracer so that auto radiographs of specimens containing different concentrations of the same element could be easily compared. Thermocouples inserted through the lid of the boat into a dummy specimen showed that, over the first 10 cm of growth, thermal conditions were quite steady, with a rate of interface advance of 5.8 cm per hr and a temperature gradient in the melt ahead of the interface of 3.0°C per cm. The specimens were seeded from tin crystals of a common orientation to eliminate orientation effects. Dilution of the specimen by seed material was minimized by the provision of a narrow neck between specimen and seed crystal. Macrosegregation. After growth, the specimens were sectioned with a spark cutter. The rods of silver alloy were cut into 1-cm lengths and analyzed for Ag110 using a y -ray counter with fixed geometry. The specimens containing thallium were cut into 2-cm lengths and analyzed for T1 204 by taking 13 counts from each end of the cut lengths through an aperture in lead sheet approximately 0.4 cm square. The results are summarized in Figs. 1 and 2. To find the effective distribution coefficient for the silver in tin alloys under smooth interface conditions, the region of substructure at the bottom surface of one of the 10 ppm specimens, see Fig. 3, was removed by spark machining before counting. Autoradiography. For both alloy systems the samples were polished on sections taken alternately parallel and perpendicular to the growth direction, and autoradiographed by placing the polished surfaces in contact with Kodak "Process Ortho" film. Figs. 3 and 4 show the structures revealed. The alloy containing 10 ppm Ag showed substructure only after a few centimeters of growth, and then substructure was limited to a narrow layer at the base. The "speckled" substructure reported previously in this system4 is here clearly seen to be an intermediate stage between planar and cellular interface conditions. The other samples show a remarkable similarity considering

Jan 1, 1969

By ED. E. Furman, R. H. Atkinson

HITHERTO the practical creep testing of precious metals has received little or no attention. The only previous creep tests of precious metals have been made with wires under conditions such as to yield much more rapid rates of creep than in engineering tests.&apos;, &apos; Up to the present time the value of creep bars of adequate size, in the absence of real need for engineering data, has deterred investigators. However, the increasing use of platinum at high temperatures has demonstrated the need for reliable creep data for the guidance of engineers, especially those engaged in designing certain specialized chemical plant equipment. In order to supply this need, creep tests were conducted at 1382°F (750°C) on 0.290 in. diam specimens of platinum, 90 pct Pt, 10 pct Rh and palladium. The platinum was high purity, nominally 99.95 pct Pt. The 90 pct Pt, 10 pct Rh was of the same high quality as is used for making gauzes for the catalytic oxidation of ammonia. The palladium was also of high purity; two batches of palladium bars were tested, one deoxidized with calcium boride and the other with aluminum. Spectrographic examination of the palladium confirmed its good quality; the only significant impurities apart from the residual deoxidizers were traces of silicon and lead. Procedure The creep bars, which were furnished by Baker and Co. to our specification, were 6 ¾ in. in overall length with a 4½ in. (4 in. gage length) reduced section 0.290 in. in diam and had the ends threaded (?-NC16). It may be of interest that the bars were valued at up to $600 each. The specimens were supplied in a 50 pct cold-worked condition to facilitate attachment of the creep extensometer, which was of the push rod type. Because of the softness of the platinum and palladium, the extensometer rings were secured to the test section by means of circular knife edges instead of the usual pointed set screws. The extensometer rods extended through the bottom of the furnace and readings were taken with a 0.0001 in. "Last Word" dial gage fastened to the rods for the duration of the test. The bars were directly loaded by hanging weights from the lower specimen grip. All tests were conducted at 1382°F ± 2°F, and an effort was made to maintain the temperature gradient over the test section within 2°F. The ends of the furnace tube were packed with asbestos wool, which allowed a very slow circulation of air through the tube. Annealing was accomplished in the creep furnace before the load was applied. The platinum and palladium specimens were annealed at the test tem- perature for about 17 and 24 hr respectively; in the case of the rhodioplatinum it was found expedient to anneal for 1 hr at 1922°F (1050°C). Pilot samples cut from the same stock as the bars were used to check annealing procedures. Pertinent measurements of grain size and hardness were recorded. Results and Discussion The creep data obtained are given in Table I and the creep curves are plotted in Figs. 1, 2, and 3. Two platinum specimens, tested under a stress of 250 psi, had almost identical creep rates at 2000 hr, namely 0.000008 and 0.000009 pct per hr. A third platinum specimen, stressed at 400 psi, had a creep rate at 2000 hr of 0.000026 pct per hr; the reason for a rather sharp decrease in creep rate during the period from 1200 to 1600 hr is unknown. As it was thought that 90 pct Pt, 10 pct Rh would have a lower creep rate than platinum, the first sample was tested at 400 psi; however, the creep rate was approximately 50 pct greater. Microex-amination revealed that differences in grain size might be responsible for the unexpected result, as annealing at 1382°F developed an average grain diameter of 0.0021 in. in the rhodioplatinum specimen compared with 0.004 in. in the platinum bar. Annealing the alloy for 1 hr at 1922°F (1050°C) increased the average grain diameter to 0.0032 in. and materially improved the creep resistance, making it much better than platinum. A second specimen annealed at 1922°F (1050°C) and tested under a stress of 550 psi had a creep rate of 0.000022 pct per hr at 2000 hr, which was still substantially lower than that shown by the specimen annealed at 1382°F (750°C) and stressed at only 400 psi. In contrast to the creep behavior of the platinum and rhodioplatinum specimens, the palladium bars, whether deoxidized with calcium boride or aluminum, were characterized by high first stages of creep. However, after about 1200 hr of test, the creep

Jan 1, 1952

By S. G. Epstein

Using the capillary-reservoir technique, electromi-gvation rates of cadmium and indium in liquid bismuth were measured at several temperatures. The electric mobility of cadmium Jrom 305° to 535°C and indium from 310° to 595°C can be expressed as a function of temperature by the equations UIn = 1.52 x 10-3 exp sq caz per v-sec Migraion of both solutes was cathode-divected at a rate rnore than four tiMes tHAt previously found for siluer in liquid bisnmth. The electric mobilities of cadmium and indiulrz in liquid bismuth at 500° C are nearly identical with their respective mobilities in mercury at room temperature. AS part of a systematic study of the variables which are considered to control electromigration in liquid metals, the electromigration rates of cadmium and indium in liquid bismuth have been measured. Mass transport properties of silver in liquid bismuth have been reported previously,&apos; and measurements of tin and antimony in liquid bismuth are forthcoming. Comparisons will be made with literature values for these same solutes in mercury.2&apos;3 This series of solutes was selected to determine the effect of the solute valence on its electromigration. Silver, cadmium, indium, tin, and antimony have nearly equal atomic masses but have chemical valences ranging from +1 to +5. They are all fairly soluble in bismuth above 300°C and all have radioactive isotopes, which are an aid in making analyses. EXPERIMENTAL TECHNIQUE Electromigration of cadmium and indium in liquid bismuth was measured by the modified capillary-reservoir technique previously described.&apos; In this method irradiated cadmium or indium is added to bismuth to form alloys containing about 1 wt pct solute (<2 at. pct solute). Several quartz or Pyrex capillaries: 1 mm ID and 5 cm long, vertically oriented, are simultaneously filled in the reservoir of the liquid alloy. A direct current is passed through two of the capillaries, which contain tungsten electrodes sealed in the upper end. The other capillaries sample the reservoir during the experiment. After a measured time interval the capillaries are removed from the reservoir and rapidly cooled. The glass is then broken away from the solidi- fied alloy, which is then weighed, dissolved in acid, and analyzed for solute content by chemical and radiochem-ical techniques. An electric mobility (velocity per unit field) can be calculated from the amount of solute entering or leaving each capillary by the simplified expression1 in which Ui is the electric mobility of the solute, ?mi the solute weight change, Ci the solute concentration of the reservoir, I the current, p the alloy resistivity, and l the duration of the experiment. This expression is valid as long as the experiment is terminated before a concentration gradient develops across the capillary orifice. Earlier experiments showed that the concentration gradient formed initially at the electrode changes with time and eventually reaches the orifice, due to back-diffusion. This condition produces a solute exchange between capillary and reservoir by diffusion or convection, opposing the electromigration, which results in a lower measured value for the electric mobility. To determine if the concentration gradient had reached the orifice, the capillaries used in some of the experiments were sectioned at 1-cm intervals and the solute content of the alloy from each section was radiochemically determined. A typical concentration profile for an experiment with indium in bismuth is shown in Fig. 1; cadmium in bismuth showed similar behavior. As illustrated in the graph, very little back-diffusion has occurred in the capillary containing the cathode, since the concentration gradient is confined to the upper 1 cm of the capillary. In the capillary containing the anode, however, the concentration gradient is much broader, extending nearly to the orifice, even though the net change in solute concentration is nearlv the same in both capillaries. Since cadmium and indium probably lower the density of bismuth when alloyed, depletion of the solute from the alloy adjacent to the anode would increase the density of the liquid in the uppermost region of the capillary. This would give rise to convective mixing within the capillary, causing the broadened concentration gradient. Conversely, the alloy adjacent to the cathode should have a reduced density as the solute concentration is increased by migration, explaining the "normal" concentration profiles found in these capillaries. This disparity was not found for electromigration of silver in bismuth. Both metals have similar densities at the operating temperatures, and nearly symmetrical concentration profiles were found in the two capillaries of each exueriment. This density effect was also apparently encountered when an attempt was made to measure diffusion coefficients for indium in liquid bismuth by the same technique which was successfully used to measure diffusion of silver in bismuth.&apos; Capillaries 1 mm ID and 2 cm

Jan 1, 1968

By R. Schuhmann, J. Th. Overbeek, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.&apos;-" Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles. The contact angle is a complex quantity because the properties of three different phases, or rather of three different interfaces, control its magnitude. Considering the interfaces close to the region of ternary contact to be plane, the relation among the contact angle and the three binary interfacial tensions is easily derived. The condition for equilibrium among the three surface tensions, Fig. 1, or the requirement of minimum total surface free energy leads to Young&apos;s equation, Eq. I: ysa — ysl = yLA cos 0 [1] According to this equation, the contact angle has one well-defined value. Actually it is found in many experiments that the value of the contact angle depends on whether the air is replacing liquid over the solid (receding angle) or the liquid is replacing air (advancing angle). The receding angle is always the smaller of the two.4 Two explanations have been offered for this experimental fact. According to some investigators,5-8 roughness of the surface causes apparent contact angles that are different for the receding and the advancing cases although the actual local contact angle may be completely determined by Eq. 1. The other explanation involves the hypothesis that the solid-air interface after the liquid has just receded is different from the same interface when no liquid has previously covered it.1,4 Adsorption of constituents of the air or liquid might play a role here. In this discussion the difference between advancing and receding contact angle will be neglected and plane surfaces where Eq. 1 describes the situation will be considered. But there is still a fundamental obstacle to the application of Young&apos;s equation. The surface tension of the liquid (rla) can easily be determined, but the two surface tensions of the solid (rsa and ySL) cannot be measured directly. Eq. 1, however, is not without value. By contact angle measurements it is possible to establish how ysl — ysl varies with the addition of solutes to the liquid phase. Also, Eq. 1 affords a convenient starting point for calculating net forces and energy changes involved in the process of bubble-particle attachment.1,2 . If for the moment surface tension of the liquid (yLa) is considered a constant, an increase in ysa — ysL, will tend to decrease the contact angle. A decrease in ySA — ysl, corresponds to an increase of the contact angle. In cases where ySA — ySL > yLa the contact angle is zero; it will only reach finite values when ysa — ysa has been decreased below YLA. Thus on the basis of Young&apos;s equation and contact angle measurements alone, it can be learned how flotation reagents affect the difference Ysa — ysl, but no conclusions can be drawn as to the effects of reagents on the individual surface tensions ysa, and ysL, not even as to signs or directions of the surface tension changes resulting from reagent additions. A quantitative relationship between the surface tension or interfacial tension and the adsorption occurring at a surface or an interface is given by the Gibbs equation, which for constant temperature and pressure reads dy = — 2 T, du, [2] where dy is the infinitesimal change in surface tension accompanying a change in chemical potential

Jan 1, 1955

By Ian J. Smalley

"Quickclay is an extreme case, it is by far the most mobile of all the common solid materials on the earth&apos;s surface. It has both a high water content and a mineral texture that allows it to flow with the utmost ease. A mass of quickclay that has lain undisturbed for thousands of years can be jarred into motion by any sudden shock." The quotation is from the paper by Kerr called, "Quickclay," which was published in Scientific American in 1963. This was probably the most widely read paper on quickclay ever published. It was reprinted by Fred Betz in his Benchmark collection on Environmental Geology (BM 25), A quickclay is an extremely sensitive soil. The sensitivity parameter is produced by dividing the undisturbed shear strength by the remoulded shear strength. If a value greater than 50 is obtained, then the soil can be classified as a quickclay. True quickclays are characterized by a very low remoulded strength of the order of 0.5 kPa. The classic quickclays are found in Scandinavia and Eastern Canada, but the 1964 Alaska earthquake revealed a considerable quick¬clay deposit underlying the town of Anchorage. This was discussed in a classic paper by Kerr and Drew in Engineering Geology in 1967. The Kerr views on quickclays were perhaps most clearly expressed in the paper with Liebling in Geol. Soc. Amer. Bull. in 1965. They suggested that the major critical conditions which contribute to quickclay movement are: substantial quantities of layer lattice silicates of colloidal size (about 40% or more by dry weight), sub¬stantial pore water (44%), a reduction in electrolyte concentration below 5 g/l of salt, and addition of a dispersant. There is still discussion and disagreement about the nature of quickclays and the mechanisms of quickclay slides; the "clay mineral"-based views favored by Kerr still find support, although an alternative "primary mineral" view suggests that it is the finely ground primary minerals

Jan 1, 1985

By Nichols J. Grant, Bill C. Geissen

In low temperature phase diagrams, liquidus curves below about 1500°C are relatively easily established, e.g., by thermal analysis or separation of coexisting solid and liquid phases, followed by chemical analysis. Experimental difficulties increase considerably at higher temperatures and in systems involving more reactive metals. Although there are now thermocouples available for use from 1600" to 2400°c, as summarized by Caldwell,&apos; the need for frequent calibration, aging, and contamination problems, and unavailability of suitable protection tubes has sharply limited their use at higher temperatures. Many of the high melt- ing metals are found to react with refractory oxides. TO avoid such problems, a frequently used procedure is the diffusion and saturation method, as described by Spedding et a1.&apos; for the system La-C. This technique involves the annealing of one metal or a suitable alloy in a crucible of the other element at a temperature above the melting point, followed by chemical analysis of the center of the melt, after equilibrium is established. Further, if an alloy system is to be investigated employing the electron microbeam probe, and calibration charts have been established, it may be possible to measure the alloy concentration at the center of a cored as-cast structure, and to conclude from this points on the liquidus curve in a manner similar to the one to be described. It is known that in phases with a broad homogeneity range the rapidly cooled, cored, as-cast structure of an alloy presents concentrations having different lattice constants; this spread of lattice constant values contributes to the broadened lines of a powder pattern for the as-cast condition. The region of the crystal which is first to solidify will then correspond to the edge of the lines if the change of the lattice parameters with concentration is monotonous. In the course of the determination of the Ta-Tr phase diagram,3 it became evident that such behavior made it possible to construct the

Jan 1, 1963

By R. L. Skaggs, D. T. Peterson

The effect of carbon in solid solution on the plastic behavior of thorium was studied by measuring the flow stress of Th-C alloys from 4.2" to 573°K and at several strain rates. Carbon was found to strengthen thorium primarily by increasing the thermally activated component of the flow stress. The strengthening due to carbon was directly proportional to the carbon content and decreased rapidly with increasing temperature up to 423" K. The flow stress also increased with increasing strain rate. The strengthening appears to be due to a strong short-range interaction between carbon atoms and dislocations. A yield point was observed in the Th-C alloys which increased with increasing carbon content. JTREVIOUS study of the mechanical properties of thorium has been confined largely to the measurement of the engineering properties. Work prior to 1956 has been summarized by Milko et al.1 who reported that additions of carbon to thorium sharply increased the room-temperature strength. In addition, the yield strength was observed to decrease rapidly over the temperature range from 25" to 500°C. In 1960, Klieven-eit2 measured the flow stress of thorium containing 400 ppm C. He found that over the temperature range from 78" to 470°K the flow stress was strongly dependent on temperature and rate of deformation. A drop in the load-elongation curve, or a yield point, was observed over most of the above temperature range. Above 470°K, the flow stress was nearly independent of temperature and strain rate. This strong temperature and strain rate dependence of flow stress is not generally observed in fcc metals. It is, in fact, more typical of the behavior reported for bcc metals. Bechtold,3 Wessel,4 and conrad5 have pointed out the striking difference between the commonly studied bcc metals and fcc metals in regard to the effect of temperature and strain rate on the flow stress. Zerwekh and scott6 studied the plastic deformation of thorium reported to contain 12 ppm C. They found that this material did not obey the Cottrell-Stokes law as expected for fcc metals. In addition, they found values of the activation volume smaller by an order of magnitude than expected for an fcc metal. They concluded that thorium was strengthened by a randomly dispersed solute. Thorium differs from many other fcc metals that have been studied extensively in that it shows a relatively high carbon solubility at room temperature. Mickleson and peterson7 report the solubility limit at room temperature to be 3500 ppm C. The lowest value reported is that of Smith and Honeycombe8 who report the limit to be 2000 ppm C at 350°C. The pres- ent investigation was a systematic study of the flow stress and yield point phenomenon of thorium over a broad range of carbon content, temperature, and strain rate. EXPERIMENTAL PROCEDURE The thorium used in this investigation was produced by the reduction of thorium tetrachloride with magnesium as described by Peterson et a1.&apos; Chemical analysis of the original ingot after arc melting and electron beam melting is shown in Table I. Alloys were prepared by arc melting this thorium with high-purity spectrographic graphite. Threaded specimens with a gage length 0.252 in. diam by 1.6 in. long were used for the constant stress or creep measurements. These specimens were machined from rod which had been cold-rolled and swaged to % in. diam. Tensile specimens were prepared by swaging annealed 3/8 -in.-diam rod to 0.102 *0.001 in. The as-swaged wire was cut to lengths of 2 in., annealed, and the center 1-in. gage length elec-tropolished to 0.100 ±0.001 in. The specimens were gripped for a length of 3 in. at each end by a serrated four-jaw collet which was tightened by a tapered compression nut. No slipping occurred in the grips and negligible deformation was observed outside the 1-in. gage length. Both the creep and tensile specimens were annealed at 730°C under a vacuum of 1 x X Torr. The resulting structures consisted of equiaxed recrystallized grains with a grain size of 3200 grains per sq mm for the tensile specimens and 2200 grains per sq mm for the creep specimens. After the specimens were prepared, samples were analyzed for nitrogen, oxygen, and hydrogen. The results of these analyses are given in Table 11.

Jan 1, 1969

By Paul W. Chase

Centralized process control has received increasing emphasis in recent years. Its application at U. S. Steel&apos;s Minntac facility for production of taconite pellets is discussed in this paper. A brief description of the flowsheet will provide background for discussion of the process instrumentation and digital system.

Jan 1, 1969

By F. E. Werner, B. L. Averbach, Morris Cohen

THAT bainite formed near the M, temperature bears a striking r esemblance to martensite tempered at the same temperature has been shown by the electron microscope.&apos; By means of electron diffraction,&apos; it has been established that carbide and cementite are present in bainite formed at 500°F (260°C); these carbides are also found in martensite tempered at 500°F (260°C).&apos; The investigation reported here is concerned with an X-ray study of the matrix phases in lower bainite and tempered martensite. These phases have turned out to be dissimilar in structure; the matrix of bainite is body-centered-cubic while that of tempered martensite is body-centered-tetragonal. A vacuum-melted Fe-C alloy containing 1.43 pct C was studied. Specimens of 16 in. diam were sealed in evacuated silica tubing and austenitized at 2300°F (1260°C) for 24 hr. One specimen was quenched into a salt bath at 410°+7 °F (210°+4°C), held for 16 hr, and cooled to room temperature. The structure consisted of about 90 to 95 pct bainite, the re: mainder being martensite and retained austenite. A second specimen was quenched from the austen-itizing temperature into iced brine and then into liquid nitrogen. It consisted of about 90 pct martensite and 10 pct retained austenite. The latter specimen was tempered for 10 hr at 410°+2°F (210°+1°C). The specimens were then fractured along prior austenite grain boundaries (grain size about 2 mm diam) by light tapping with a hammer. Single aus-tenite grains, mostly transformed, were etched to about 0.5 mm diam and mounted in a Unicam single crystal goniometer, which allowed both rotation and oscillation of the sample. Lattice parameters were measured by the technique of Kurdjumov and Lyssak. This method takes advantage of the fact that martensite and lower bainite are related to austenite by the Kurdjumov-sachs orientation relationships Thus, the (002) and the (200) (020) reflections can be recorded separately, permitting the c and a parameters to be determined without interference from overlapping reflections. According to these findings, the matrix phase in bainite is body-centered-cubic and, within experimental error, has the same lattice parameter as ferrite (2.866A). On the other hand, martensite, tempered as above, retains some tetragonality, with a c/a ratio of 1.005t0.002. Most workers in the past have assumed that bainite is generated from austenite as a supersaturated phase, but the nature of this product has not been established. The question arises as to whether bainite initially has a tetragonal structure and then tempers to cubic, or if it forms directly as a cubic structure. If it forms with a tetragonal lattice, it might well be expected to temper to the cubic phase at about the same rate as tetragonal martensite. The martensitic specimen used here was given approximately the same tempering exposure, 10 hr at 410°F, as suffered by the greater part of the bainite during the isothermal transformation. About 50 pct bainite was formed in 6 hr at 410°F. On tempering at this temperature, martensite reduces its tetragonality within a few minutes to a value corresponding to 0.30 pct C.&apos; Further decomposition proceeds slowly, and after 10 hr the c/a ratio is still appreciable, i.e., 1.005. Thus, even if the bainite were to form as a tetragonal phase with a tetragonality corresponding to only 0.30 pct C, which might be assumed to coexist with e carbide, it would not be expected to become cubic in this time. It seems very likely, therefore, that bainite forms irom austenite as a body-centered-cubic phase and does not pass through a tetragonal transition. The carbon content of the cubic phase has not been determined, but it could easily be as high as 0.1 pct, within the experimental uncertainty of the lattice-parameter measurements. It has been postulated that retained austenite decomposes on tempering into the same product as martensite tempered at the same temperature. There is now considerable doubt on this point. The isothermal transformation product of both primary and retained austenite at the temperature in question here is bainite," and the present findings show that bainite and tempered martensite do not have the same matrix. Acknowledgments The authors would like to acknowledge the financial support of the Instrumentation Laboratory, Massachusetts Institute of Technology, and the United States Air Force.

Jan 1, 1957

Report of President The important fact of the year 1916 is that on July 25 contracts were executed by which the American Society of Civil Engineers because an additional Founder Society and arranged to make its permanent home in our building. The contracts provide for the construction of three additional stories to the building, the American Society to pay the cost tip to $250,000, this being considered equivalent to what each other Founder Society had contributed, the American Society to participate in the original Carnegie gift and have an equal share in the property with each other Founder society. The construction of the addition to the building is under way, $62,525.04 having been expended thereon in 1916. It has been found that, clue to war conditions and the advanced price of materials, the cost of the addition will be $300,000. The founder societies have been requested to assume the extra $50,000, one quarter each. This work is in charge of a Building Committee consisting of H. H. Barnes, Jr., Chairman, E. G. Spilsbury, Charles Warren Hunt and Charles F. Rand. At the request of the Founder Societies, important alterations were made in the lecture halls on the fifth floor of the building to make the same suitable for social functions of the societies. The cost, $6,642.08, was advanced by the United Engineering Society but is to be paid eventually by the Founders. The Library of the civil Engineers is being merged with the Library of the United Engineering. Society and the other founder societies. At the present time the membership of the four founder societies is 29,000 and of associate societies 23,000, so that a total of 52,000 engineers now have their headquarters in our building. The value of the real estate now owned by this Society is $1,647,171.16. This sum will be increased at the end of 1917 by the amount of the cost of the addition to the building.

Jan 3, 1917

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872 R W RAYMOND 1873 R W RAYMOND 1874 A L HOLLEN 1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 ECKLEY B COXE 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882

Jan 1, 1910

[OFFICERS AND COMMITTEES J. W. Woomer, President A. B. Cummins, President-elect S. D. Michaelson, Past President C. E. Lawall, Eastern Regional Vice-President D. W. Scott, Central Regional Vice-President J. D. Forrester, Western Regional Vice-President R. B. Ladoo, Treasurer John Cameron-Fox, Secretary]

Jan 1, 1961