Search Documents

By G. P. Conard, E. H. Rennhack

The creep behavior of hot-rolled, hypoeutectic Zn-Ti alloys was investigated in the temperature range from 0.43 to 0.53 TM. Secondary flow was found to originate primarily from strain-induced gvain growth where grain boundary )nigvation served to relieve the strain energy of distortion introduced by slip, grain boundary sliding, and subgvain formation. The extent to which this recovery mechanism operated was determined by the ratio of grain width to the spacing between planar fibers of TiZn,, compound particles generated in these alloys during rolling. When this ratio was unity, creep resistance demonstrated a marked improvement. In this condition, which was fulfilled by annealing following rolling, structural stability was enhanced with decreasing grain size below the equicohesive temperature (-0.5Tm), while the reverse was true above this temperature. TITANIUM concentrations approaching the eutectic composition of 0.23 wt pctl have been shown to promote a significant increase in the creep resistance of rolled zinc,2 The alloying effect created with titanium is somewhat unique; a structure closely resembling that of a fiber-reinforced metal composite can be developed which selectively modifies creep strength in preference to other mechanical properties. In an earlier investigation,~ the present authors found that, while the fiber network, composed of individual TiZn,, compound particles, had a distinct influence on rolled texture, the crystallographic variations produced were of minor importance with respect to creep. Rather, creep resistance seemingly increased when the grain size appeared to coincide with the in-terfiber spacing. The work described here was undertaken to explore this effect in greater detail. EXPERIMENTAL PROCEDURE Three zinc-base alloys containing 0.05, 0.12, and 0.16 wt pct Ti were prepared from CP zinc and iodide titanium in the form of 4 by 2 by f in. chill-cast ingots. The melting and casting procedures for these alloys have been detailed el~ewhere.~ Individual ingots of each alloy were hot-rolled at 200°C (392°F) to total reductions of 10, 25, 50, 75, and 90 pct in from one to five passes, respectively, employing a 10-min reheat prior to each rolling pass. With grain, tensile-type creep specimens with a 1-in.-long, -in.-wide gage section were machined from the rolled strips for test purposes. Annealing studies to explore the influence of grain size on secondary creep flow were carried out at 400°C (752°F) in argon for times extending up to 60 min. The grain-size effect was evaluated in terms of average grain width and length values statistically derived from lineal intersection measurements.4 A similar method was applied in establishing the average interfiber spacing, i.e., average perpendicular distance between adjacent planar fibers. The creep characteristics of the alloys were investigated by means of constant-load and constant-stress creep tests. The former tests were conducted at 25°C (77°F) under an initial stress of 10,000 psi, while the latter were performed in the range from 25°C (77°F) to 90°C (194°F) at stress levels varying from 8000 to 22,000 psi. Total specimen strain, as determined with Budd HE-1161-B strain gages, was in excess of 0.10. Maintenance of constant stress was achieved through periodic load reductions made at 0.01 strain intervals to compensate for the attendant incremental reduction in specimen cross-sectional area. The maximum indicated error in the applied stress at these strain intervals was less than 3.0 pct. RESULTS AND DISCUSSION Constant-Load Creep. In an effort to clarify the in-terrelation between interfiber spacing and grain size with respect to the creep resistance of the Zn-Ti alloys, their separate effects on secondary creep rate were determined as a function of titanium content and rolling reduction. These results are set forth in Figs. 1 and 2, respectively. The average grain diameter plotted in Fig. 2 was resolved from average grain width and length values. No data are presented for reductions of less than 50 pct because of the inability to obtain consistent measurements on these strips. The curves of Fig. 1 indicated that, for a given titanium content, a decrease in interfiber spacing, as produced with increasing reduction, promoted a decrease in creep rate. Depending on titanium content, however, wide variations in creep rate occurred at the same interfiber spacing suggesting that interfiber spacing, by itself, has little or no influence on creep resistance. Grain size, on the other hand, decreased progressively with both increasing rolling reduction and titanium content, the effect of which led to a pronounced decrease in creep rate, particularly when the average grain diameter became smaller than 3.0 x 10"4 in., Fig. 2. The continuity of this relationship tended to support the view that grain size rather than interfiber spacing was predominant in controlling secondary creep. Annealing Effect. The observed dependence of creep flow on grain size suggested that a further contribution to creep resistance would result when the alloys were annealed to effect a coincidence between grain width and interfiber spacing, see Fig. 3(b). ~eiides creating an immediate barrier to grain boundary movement, annealing offered the possibility of providing increased structural stability by eliminating many high-energy, mobile grain boundaries.= To test this hypothesis, specimens from the Zn-0.16 Ti strips reduced 75 and

Jan 1, 1967

By D. L. Sikarskie, B. Paul

A theory is presented for the static penetration of a single rigid wedge into brittle material. The material considered is one which exhibits both crushing and chipping phases in the penetration process. If the wedge angle and three parameters are specified, the theory predicts forces and associated penetrations during both the crushing and chipping phases. For certain ranges of the parameters agreement with the limited experimental data available is promising, except for the initial phase of the penetration process where refinements on the proposed theory are required. The theory also predicts that for certain values of the wedge angle and other known parameters, the chipping process does not occur and penetration is due entirely to crushing. When viewed in detail, the drilling of rock by percussive means involves, among other things, system dynamics, actuating forces, dynamic stress levels and the actual penetration mechanism of the bit into rock. If rock drills are to be significantly improved, a thorough understanding of the entire system would be highly desirable. In this paper, one aspect of the system, namely the mechanism of penetration of the bit, will be studied in detail. It has been found1 that for the velocities encountered in percussive drilling (of the order of 20 fps) a static analysis adequately describes the penetration process, at least for some rocks. Hence, we will only be concerned with describing analytically the static penetration of a single wedge shaped tool. It will further be assumed that the wedge is long enough to permit a two-dimensional analysis. Numerous authors have studied the static penetration of a wedge into rock. The following papers give some of this work and provide additional references to other work. Cheatham2,3 has assumed the rock to behave plastically and has obtained force-penetration equations for both Coulomb-Mohr and parabolic yield criteria. Evans and Murrell4 have studied the penetration of two types of coal and have found equations relating the penetration characteristic (P/dSc) to wedge angle for the various strength coals tested. race' attempted to find a correlation between hardness as determined by indenting the material and other mechanical properties and concluded that the results of such a test are generally inconclusive. His paper however contains a very extensive bibliography on the indenting of many different materials. Gnirk6 also has a fairly complete literature review on the static penetration of rock, of which he makes use in his indexing studies. A wide range of behavior is found in the wedge penetration of different rocks under different external conditions. For example, a rock that is essentially elastic-brittle at standard pressure may become elastic-plastic at a high confining pressure.7 It has also been observed4. " that some rocks will merely be crushed and indented by a wedge, whereas others will crack and form chips, furthermore the existence or non-existence of chips depends in great measure on the geometry of the indentor, type of rock and the depth of penetration. Hence, to attempt a theory which embraces all possible behavior is not practical at present. We, therefore, confine our attention to predicting the force-penetration characteristic and volume removal behavior for a type of rock which exhibits both crushing and chipping phases in the penetration process. Such behavior is characteristic of the harder rocks such as granites and represents a more difficult problem than the behavior of softer rocks such as coal and certain sandstones. In this preliminary study an attempt will be made to describe only the essential features of this complex penetration process. A qualitative description of these essential features is obtained with the aid of Fig. 1.1, where a wedge of vertex angle 28 is shown at some intermediate stage of the penetration process. As the wedge advances, the rock is fragmented (i.e. crushed) in some local region surrounding the wedge, the shape of this region being unknown. Simultaneous with the fragmentation in this local region, essentially elastic stresses are assumed to be building up in the surrounding rock. When a certain penetration level, di+1, is reached, the stresses along some surface are sufficient to cause failure and a chip is thus formed. The process now repeats, i.e., a crushing phase followed by the formation of a chip.

Jan 1, 1965

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

H. G. DAVIS, * Wilkes-Barre, Pa. (written discussion ? ).-The only practical method of testing mine air for gas, until recent years, was by the effect of the gas on the flame of the ordinary Davey Lamp, and it is quite surprising how nearly the correct percentage of gas can be deter-mined by many men by observing the behavior of the safety-lamp flame in the different mixtures. Mine foremen frequently guess the percentage of gas to within 0.1 per cent., making certain allowances to cover the dust-laden atmosphere, in which the test was made. It is not meant by this that anthracite dust is explosive, but that its properties increase the length of a fuel cap on an ordinary oil-burning lamp, which, as Prof. -Young contends, increases in height with the proportion of gas and in-creased temperature. Naphtha or benzine-burning lamps have a hotter flame, and, there-fore, are more sensitive so that a smaller percentage of gas can be detected. Some of the fire bosses in this region some years ago preferred the Koehler lamp, while others did not care to use it in their morning examinations. In 1911, when the experimental mine of the Bureau of Mines at Bruce-ton, Pa., was being prepared to be exploded, a large number of mining men went through it to examine the entries, which were lighted by electricity. While so doing, they saw in the face-return-airway a Koehler or Wolfe lamp, that seemed to he burning with difficulty. An investigation showed that the lamp had been filled to overflowing with naphtha and was generating this surplus gas. This shows how easily we can be

Jan 11, 1919

By H. Macpherson

Durhm has a well earned reputation for supplying some of the finest coking caals in the world. The caals, in general, vary in rank from 301 to 501/2. Durham has traditionally produced foundry coke for the major proportion of the foundries in Great Britah. Durham coals can be described as clean, soft coals, which yielded, with the old hand methods of coal getting, low ash small coal because the extraneous shale was normally harder than the coal and occurred in larger pieces. Under these conditions, with a plentiful supply of cheap labor, it used to be sufficient, at most collieries, to hand clean the large sizes of coal which could then be remixed with the untreated small coal to produce carbonization coals, ready for the coke ovens, at under 5 pct ash. With the introduction of mechanical methods of coal mining, the coal gradually required more cleaning. The first method adopted to resolve this problem was the introduction of pneumatic dry cleaners for the small coal. Although such machines had little effect on the fine coal (say below 1/8 in.), they could clean the intermediate sizes of coal. This, coupled with hand cleaning the larger sizes above 1-1/2or 2 in., resulted in a combined run-of-mine mixture below 6 pct ash, capable of maintaining the quality and reputation of the cokes produced. In more recent years, the intensification of mechanization and power loading, coupled with gradual exhaustion of the cleaner seams, has created the need for a more complete method of coal cleaning. This particularly applies in the fine sizes (say below 1/50 in.) which normally vary, under present day conditions, between 15 and 35 pct ash and are much too dirty to be included in the raw state in a carbonization mixture. This pronounced change has been accelerated because legislation controlling the dust conditions of mine airs for the prevention of pneumoconiosis has resulted in tk~e extensive use of water underground and a consequent increase in moisture content of the run-of-milie output. The presence of damp fine coal decreast the efficiency of prescreening and dry cleaners, so that this type of preparation for low ash coking coals is decreasing, although it is still used satisfactorily for industrial coals in the medium ash range. Table I shows the gradual increase in mechanization, the reduction in manpower, the increased use of explosives per ton of coal extraction, and the increase in the proportion of coal cleaned by mechanical means in Great Britain. Although similar figures are not available for Durham Div. until after the date of nationalization of the coal industry, it is probable that the increase in mechanical cleaning, particularly by dry cleaners, was more marked in the Durham collieries than elsewhere in the country. As dry clealiers were replaced by coal washeries in the Gritish ccal industry, no special attempts were made to recover the slurry, with the result that large outflows of dirty water were allowed, deposits of slurry came in to lagoons and neighboring streams, and a proportion of fine material was lost from the coking coal. This position, coupled with the higher moisture of the washed coking coal, resulted in adverse effects on coke oven throughputs and coke quality. It is now realized that the natural coal fines are an essential ingredient of coking coals in obtaining the correct coke structure in metallurgical cokes. This, together with economic pressure, led to the introduction of flocculation and filtration plants for the recovery of slurries, and later, when the ash contelits of the filter cakes were too high, to the introduction of froth flotation equipment. After this position had been reached, the tailings from the froth flotation pIants were, in many cases, still allowed to constitute an undesirable effluent. Recent legislation on river pollution has changed this picture; it is now necessary to provide a circuit which is completely closed so far as solids are concerned. The gradual increase in the coal cleaned by wet methods and froth flotation in Durham Div, is shown in Table 11. It is now an accepted feature of new Washeries that. froth flotation should be an integral part of the washing process from the initial installation of the plant.

Jan 1, 1962

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By H. E. Cline, E. F. Koch, J. L. Walter

It has been postulated and, in a few instances shown, that some kind of dislocation structure will be present at semicoherent interfaces to accommodate small lattice mismatches. In the present study of the NiAl-Cr eutectic, regular arrays of interface dislocations are observed at the boundary between the chromium-rich rods and the NiAl-rich matrix. The networks were examined by transmission electron microscopy and selected area diffraction. The rods and the matrix have a crystallographic relationship in which all directions and planes of the two phases are parallel. The dislocation networks are cmposed of a<100> dislocations lying on the intersections of the cylinders with (100) planes. Dislocations forming hexagonal rather than square arrays are also observed at certain areas of the network. The morphology of the network is consistent with the interpretation of mismatch being accommodated by interface dislocations in the cylindrical geometry. The measured spacing between dislocations was used to calculate an apparent lattice mismatch between the phases (˜0.35 PCt)interface network energy (-140 ergs per sq cm), and network strengthening (-10,000 psi). It has been proposed by Frank and Van der Merwe1 that dislocations should be present at the boundary between two semicoherent crystallographically related phases. The role of the interface dislocations would be to reduce the internal stresses, caused by the mismatch in atomic spacing across the interface. Such dislocations have been observed at the interface between expitaxially grown films and Substrates.2-4 Interfacial dislocations have also been observed at precipitate-matrix interfaces.&apos;-&apos; Directionally solidified eutectics have been shown to have semicoherent phases1&apos; and would, therefore, be expected to have interfacial dislocations as found by Weatherly at a lamellar fault in A1-A12Cu.11 The NiAl-Cr eutectic appeared to be a promising system to examine because both phases are cubic, the lattice mismatch is small, and the phases are crys-tallographically related. Furthermore, the eutectic is easily thinned for transmission microscopy. Indeed, interfacial dislocations were observed and this report describes the nature of the dislocation networks in the boundary between the NiAl-rich ma-trix-phase and the fine chromium-rich rods.21 I) EXPERIMENTAL PROCEDURE Ingots, 3/4 in. in diam and 6 in. long were made by melting in vacuum and casting under argon using 99.9 pct pure material. The composition, in at. pct, was 33 pct Ni, 33 pct Al, and 34 pct Cr. The ingots were then placed in A1203 crucibles on a water-cooled base, melted by means of induction, and withdrawn from the hot zone at the rate of 1 in per hr under argon.* * T his material was first directionally solidified in this laboratory by E. R. Stover Slices were taken perpendicular to the growth direction of the directionally solidified ingot for metallography and for transmission electron microscopy. The electron transmission samples were thinned mechanically, then thinned electrolytically in A-2 electrolyte* *A-2 electrolyte: 62 ml perchloric acid, 700 ml ethanol, 100 ml butylcellosolve, 137 ml distilled H20. until a hole appeared in the foil. 11) EXPERIMENTAL RESULTS A) Optical Microscopy. The microstructure, viewed on a plane perpendicular to the growth direction, is shown in Fig. 1. The structure consists of cells or colonies of parallel chromium-rich rods in the NiAl matrix. The cells occur when there are impurities present12 or, in a ternary eutectic, if the composition is slightly off the eutectic composition. The axis of the chromium-rich rods is parallel to the growth direction except near the cell boundaries. Here the rods may assume angles to the growth direction; however, examination shows that the crystallographic relationship between the rod and the matrix remains the same. Fig. 1 includes cell boundaries where the rods formed at a large angle to the growth direction. The variation of rod position across the cells made it possible to Fig. 1-Structure on plane perpendicular to growth direction. Rods near cell walls are at large angle to growth direction. Magnification 315 times.

Jan 1, 1970

By A. D. Hughes

C. W. MERRILL*—Mr. Hughes&apos; paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably. a matter of vital interest. Your Chairman, Mr. Romanowitz, in his introduction, referred to the fact that I had been a member of the United States delegations to the three meetings of the International Tin Study Group. Some cominents on the Group&apos;s objectives and deliberations may be of interest. When it appeared that the International Tin Committee, the prewar producer&apos;s cartel, might soon revive its operations and extend its control agreement beyond the expiration date of Dec. 31, 1946, the United States Government became interested in some kind of an international trade organization concerned with tin which would give the consumers&apos; interest equal representation with the producers&apos; interests. An international meeting was called in London in October 1946 to consider this problem. I did not attend that meeting hut the result of the meeting was the organization of the International &apos;Tin Study Group which

Jan 1, 1950

C. N. FEnner, New York City (communication to the Secretary) : A possible explanation of some of the&apos; phenomena of amalgamation cited by Mr. Bayliss and others has occurred to me. We know that if, to a quantity of mercury, gold and silver are added until a putty-like paste is formed, and if this mass is spread on a flat surface and pressure is applied, a more fluid portion of the mercury will be squeezed out from the rest, carrying gold and silver with it. The proportion of gold to silver will depend, I think, upon various causes and conditions—the relative chemical affinity which gold and silver have for mercury; the amount of pressure used; the presence of other metals:

Jan 1, 1898

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to over-produce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metal-based economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening. The metal age started many centuries ago, and with the exception of the noble metals, barely a dent was made in world reserves until the present century. Then, as a result of the pioneering ideas of D. C. Jackling and Paul Gemmel, and the willingness of the McNeals, Penroses and Guggenheims to back ideas with money, a virtual explosion of metal production was propagated throughout the world. It is important to examine the causes of this expansion to determine whether it is a trend that may be sustained or whether it is anomalous and therefore attributable to circumstances not likely to be repeated or continued. This period of plenty is a once only phenomenon. Vast metal resources have been sitting around here for eons, while the world was unaware of or unconcerned with their existence. But when population began to grow exponentially, and ways were discovered to use metals to develop machines to do the work of men and animals, the exploitation of raw materials increased at a staggering rate. And now the realization is dawning that minerals are a wasting asset and are beginning to present supply problems that should begin to be of concern. Two main factors have caused this condition; One is the population growth, and the other is the expanding demand for irreplaceable raw materials as nations become more developed. A group of systems analysts, at Massachusetts Institute of Technology in a book Limits of Growth, has warned that at present rates of population growth and resource consumption together with environmental constraints, a point will be reached within 100 years when the world population will become totally incapable of supporting itself. The authors conclude that this end result could be avoided if a planned equilibrium could be established at a lower rate of population growth and resource consumption. Fortunately, there is evidence that the population problem is moderating. The growth rate in the U.S. has decreased from 2.3% per year in 1900 to 1.1% in 1970. But, even at the lower rate, population will double in 70 years. The world rate is greater, and if it continues, world population will rise from 3.5 billion to nearly 10 billion in 50 years. All of these projections are questionable because the dangers of growing population are now being recognized. A marked decrease in growth rate has been noted in the more developed countries-in fact, it was zero in the U.S. in 1972. The other factor affecting consumption of raw materials is the increase in per capita use of most items as individuals become more affluent. Many economists believe that developing countries such as China and India represent a vast future potential market; but there are others, with whom the author agrees, who believe over-population tends to stagnate development. Nevertheless, it is a fact that vigorously developing societies increase consumption at a rate far above their population growth rate.

Jan 1, 1974

A MINING institute open to all men interested in any branch of the mining industry will be held at the Col-lege of Mines, University of Washington, Seattle, during the week beginning March 5. Prospectors, miners, mine owners, persons interested in metallurgy, investors in min-ing enterprises, and the public generally are invited to at-tend. This institute will take the place of the Winter Min-ing Session which originated at Seattle in 1897 and con-tinued for twenty-eight years. The complete new equip-ment of the Mines Laboratory will be used to give demon-strations of new machines and processes of mining, ore dressing, and metallurgy. This year the ceramic industry, including cement and branches of clay working of special Importance in the Northwest, will be included in the insti-tute. All instruction will be given by specialists. Prominent technical men and managers will give lectures on their special subjects. Among the speakers engaged are G. T. Jackson, formerly superintendent of the Alaska-Gas-tineau and the Chichagof mines, who will speak on the mining of large bodies of low-grade ore; R. F. McElvenny, superintendent of the Tacoma Smelter, on the nature of contracts that a smelter can offer to mines and prospects; M. D. Leehey, mining lawyer, on some popular errors re-garding the mining law; H. H. Townsend, on the explora-tion and purchase of prospects by operating companies; J. L. McAllen, on quartz mining in the Willow Creek dis-trict, Alaska; F. Powell, on gold dredging. In the evenings, lectures illustrated by stereopticon views and moving pic-tures will be given. The week will close with an excursion o mines and plants.

Jan 3, 1928

By Marie Kinzel

LOS ALAMOS, New Mexico, the birthplace f the atomic bomb, is one of the most famous-and mysterious-places in the world. It leaped into fame on Aug. 6, 1945, when the first atomic bomb burst over Hiroshima. Unheard of until that day, its present life is as hidden from most people as was its very existence in pre-Hiroshima days. Then, those who did know of it dared not breathe their knowledge. "What do you tell your wife when you go to Shangri La?" was the favorite quip of the few consultants who made regular trips from east or west to Los Alamos during the tense months when the bomb was in the making. Security regulations made it impossible even to hint at the rigid secrecy surrounding the project. The puzzled wives in question knew only that their husbands had top priority on airplane flights to Albuquerque. When they had verified the safe arrival of the flight, they undoubtedly breathed a sigh of relief. If they could have visualized the rest of the trip, the sigh of relief would have been replaced by a state of tizzy, until a telegram came saying "Arriving home on Flight X" (on a nice safe airplane).

Jan 1, 1946

By H. I. Aaronson, C. Wells

Configurations of ferrite crystals have been found in a plain carbon steel which appear to have resulted from the nucleation of new ferrite crystals at the interphase boundaries of previously formed crystals despite the high carbon concentrations which necessarily develop at these boundaries. This phenomenon has been termed sympathetic nucleation. An attempt has been made to reconcile the occurrence of sympathetic nu-cleation with current nucleation theory. THIS investigation is one of a series on the formation of proeutectoid ferrite from austenite. From the viewpoint of chemical composition, this reaction consists of the nucleation and diffusional growth of crystals of carbon-poor ferrite within a matrix of carbon-rich austenite. The austenite adjacent to the austenite-ferrite boundaries will be greatly enriched in carbon, approximately to the value of the y/(a + y) equilibrium curve or its metastable extrapolation at the temperature of transformation. Those areas of austenite appreciably farther removed from the growing ferrite, on the other hand, will be relatively unaltered in composition, especially at the earlier stages of transformation. Since rates of nucleation are considered to decrease exponentially with decreasing supersaturation,&apos; the frequency with which ferrite nuclei appear at austenite-ferrite boundaries should be negligible in relation to that at which they form in other regions of the austenite. During this investigation, however, many groupings of ferrite crystals have been found which appear to have resulted from the nucleation of ferrite at austenite-ferrite boundaries. This phenomenon has been given the name of sympathetic 71.1tcleation. A number of micrographs of morphological configurations caused by sympathetic nucleation will be presented, after which an explanation for this reaction will be proposed in terms of current nucleation theory. Some of the structures to be considered are composed of bainite, an aggregate of ferrite and carbide, rather than of ferrite. Since ferrite and bainite differ only in that bainite forms under conditions which result in the nucleation of carbides behind the advancing austenite-ferrite boundaries,&apos; it will usually be unnecessary, for the purpose of this paper, to distinguish between the two reaction products. All studies were performed on an electric furnace steel (obtained from the Vanadium Alloy Steel Co.) containing 0.29 pct C, 0.76 pct Mn, 0.25 pct Si, 0.005 pct P, and 0.007 pct S. The alloy was cast as a 150 Ib, 7x7 in. cross section ingot and forged into bars 2x2 in. in cross section. These bars were homogenized for 48 hr at 1250°C in an Endo-Gas atmosphere. The depth to which decarburization penetrated during this heat treatment was determined by chemical and microscopic analyses and the affected metal was removed by machining. Specimens for isothermal transformation studies were cut from the remaining material; most of these specimens were 1/2x1/4X1/16 in., though some with a thickness of 1/32 in. were prepared for use at the shorter reaction times and lower reaction temperatures. Specimens were austenitized for 30 min at 1300°C, isothermally reacted for various times at temperatures ranging from 775" to 475 "C, and then quenched in iced water. The austenite grain sizes within individual specimens ranged from ASTM Nos. 1 through —4. A commercial heat-treating salt which was continuously deoxidized by an immersed graphite crucible served to minimize the loss of carbon during austenitizing; thick covers of powdered graphite and immersed graphite rods effectively prevented decarburization in the lead pots employed for the isothermal reaction treatments. The heat-treated specimens were sectioned and mounted in Bakelite. Following the completion of standard grinding and mechanical polishing procedures, the specimens were electrolytically polished with a Buehler-Waisman apparatus and etched in 2 pct nital. Experimental Results Rules of Evidence for Sympathetic Nucleation—On the basis of observations made on a single plane of polish, one precipitate crystal may be considered to have been sympathetically nucleated at the inter-phase boundary of another precipitate crystal when the following conditions are fulfilled: 1) The sympathetically nucleated crystal is not in contact with a grain boundary or a subboundary in the matrix phase. 2) The shape, size, and location of the crystal at whose boundary sympathetic nucleation occurred (hereafter termed the base crystal) and the crystal formed by sympathetic nucleation substantially pre-clude the possibility that the plane of polish em-ployed may have concealed the fact that both crys-tals actually nucleated at a grain boundary or a sub-boundary in the matrix phase.

Jan 1, 1957

SINCE I promised you above when speaking of the melting of metals to teach you to make small crucibles and shells for melting, I do not wish to fail in my promise. For, in truth, since they are instruments that are much used for this procedure, they increase the work if they are not good, and often cause great extra expense as well as necessitating repetition of the work. If they are good they save everything. Therefore, if you have to make them, do it so that they, are greatly aided by art. It is first necessary to have the clay of a good nature, that is, resistant to the force of the fire by its own natural virtue, either when it is lean or when its viscousness is mixed with much talc, and whether it is yellow or white. This should be well freed from small stones and beaten well with an iron, and then thoroughly mixed by hand. With this should be mixed an eighth part of finely ground and sifted iron scale,* and also some [145] young ram&apos;s-horn ashes. These things should be well mixed together by hand and by beating them. If this clay should not be strong enough by itself, it is mixed with another lean clay, with crushed peperino, flintstone, or some other stone that in your judgment seems to be arid and resistant. Crucibles are worked on a low potter&apos;s wheel turned by hand, or on a high one turned by foot, just as plates are made. Both large and small ones are made. Most of them are given a triangular shape at the mouth, and the shells have a kind of spout for ease in pouring out the metal. This done they are well dried, and baked in furnaces like pots or other vessels. At the end, when they have been thus made they are used for melts.

Jan 1, 1942

By A. R. Orban, R. B. Engdahl, J. D. Hummell

The initial phase of a research program on smoke abatement from Bessemer converters is described. In work sponsored by the American Iron and Steel Institute, a 300-lb experimental Bessemer converter was assembled to simulate blowing conditions in a commercial vessel. Measurements of smoke and dust were also made in the field on a 30-ton commercial vessel. During normal blows the dust loading from the laboratory converter averaged 0.51 lb per 1000 lb of exhaust gas. This was similar to the exhaust-gas loading of a commercial vessel. The addition of hydrogen to the blast gas of the laboratory converter caused a decided decrease in smoke density. Smoke was also reduced markedly when methane or ammonia was added instead of hydrogen. The research is continuing on a bench-scale investigation of the mechanism of smoke formation in the converter process. DURING the past 2 years, on behalf of the American Iron and Steel Institute, Battelle has been conducting a research program on the control of emissions from pneumatic steelmaking processes. The objective of the research program is to discover a practical method for reducing to an unobjectionable level the emission of smoke and dust from Bessemer converters. PRELIMINARY INVESTIGATION Although conceivably some new collecting technique may be devised which would be economically practicable for cleaning Bessemer gases, no such system based on presently known principles seems feasible because of the extremely large volume of high-temperature gases involved. Hence, the research is being directed toward prevention of smoke formation at the source. A thorough review was first made of former work to determine the present status of the cleaning of converter gases. No published work was found on work done in the United States on collecting smoke or on preventing its formation in the bottom-blown, acid-Bessemer converter. In Europe, however, a number of investigations have been made on the basic-Bessemer converter. Kosmider, Neuhaus, and Kratzenstein1 conducted tests on a 20-ton converter to obtain characteristic data for dust removal and the utilization of waste heat. They concluded that because of the submicron size of the dust, special equipment would be necessary to clean the exhaust gases. Dehne2 conducted a large number of smoke-abatement experiments at Duisburg-Huckingen in a 36-ton Thomas converter discharging into a stack. A number of wet-scrubbing and dry collectors were tried unsuccessfully. A waste-heat boiler and electrostatic collector with necessary gas precleaners was felt to be the best solution for this particular plant. Meldau and Laufhutte3 determined that the particle size was all below 1 µ in the waste gas of a bottom-blown converter. Sel&apos;kin and zadalya4 describe the use of oxygen-water mixtures injected into a molten bath in refining open-hearth steel. They claim that with use of oxygen-water mixtures the amount of dust formed was reduced between 33.3 and 20 pct of its previous level, and emission of brown smoke almost ceased. Pepperhoff and passov5 attempted unsuccessfully to find some correlation between the optical absorption of the smoke, the flame emission, and the composition of the metal in a Thomas converter in order to determine automatically the metallurgical state in the melt. In a recent U. S. Patent (NO. 2,831,762)&apos; issued to two Austrian inventors, Kemmetmuller and Rinesch, the inventors claim a process for treating the exhaust gases from a converter. By their method the inventors claim that the exhaust gases from the converter are cooled immediately after leaving the converter to a degree that oxidation of the metal vapors and metal particles to form Fe2O3 is inhibited in the presence of surplus oxygen. Gledhill, Carnall, and sargent7 report on cleaning the gases from oxygen lancing of pig iron in the ladle. They claim the Pease-Anthony Venturi scrubber removed 99.5 + pct of the smoke, thereby reducing the concentration to 0.1 to 0.2 grain per cu ft, which resulted in a colorless stack gas after the evaporation of water. Fischer and wahlster8 developed a small basic converter and compared the metallurgical behavior of the blow with that of a large converter. Later work by Kosmider, Neuhaus, and Hardt9 on the use of steam for reduction of smoke from an oxygen-enriched converter confirmed that the cooling effect of steam is detrimental to production. From review of all of the published information on the subject, it was concluded that a practical solution to the smoke-elimination problem had not been found. Accordingly, it was deemed desirable to investigate the feasibility of preventing the initial formation of smoke in the converter.

Jan 1, 1961

By A. H. Heim

A method and apparatus for measuring gas porosities of rocks are described. The apparatus can be assembled from commercially available components. In principle, measurements are made by volume substitution at constant pressure. The maximum error is not more than 0.3 porosity per cent. Typical results are given. INTRODUCTION Determining the porosity of rock samples is one of the most important and yet most varied types of measurement in core analysis. Among the many techniques devised are the so-called "gas porosity" methods. An old and well known example is the Washburn-Bunting method.&apos; The U. S. Bureau of Mines2-&apos; described and later improved the apparatus for a now widely used method generally known as the "Boyle&apos;s law" method. In the present form of the Washburn-Bunting method,&apos; the volume of air in the pores of a rock sample at atmospheric pressure is extracted and then collected in a graduated burette at atmospheric pressure. The volume of air is read directly as the pore volume of the sample. The absolute error in reading the collected volume of gas is independent of the total volume; thus, the relative error is larger when the volume is small, as it is for rocks of low porosity. In addition, the sample after measurement contains mercury, which limits its use for other analyses. The Bureau of Mines (or Boyle&apos;s law) method measures directly the solids volume of a sample from which the pore volume and porosity are derived, using a separate measurement of the bulk volume. Gas at a few atmospheres pressure is introduced into a sample chamber of known volume containing the rock sample. The pressure is accurately measured. Following, the gas is expanded into a burette at 1 atm, and the gas volume is read directly. From the initial pressure p, and the final pressure p2 and volume v,, the initial gas volume v1 is calculated using Boyle&apos;s law; that is, p1v1 = p2v2. Volume v, minus the volume of the empty sample chamber is the solids volume of the sample. The accuracy of the method is limited, unless corrections are made, by deviations of the gas from the "ideal" gas-law behavior assumed in the simple form of Boyle&apos;s law. The purpose of the present paper is to describe a method for measuring the gas porosity of a rock which avoids many of these difficulties. Gas volumes are measured directly with the same accuracy as the bulk volumes. Pressures of at least an order of magnitude larger than those of previous methods are employed to insure rapid penetration of the gas into the sample. While special equipment may be built to apply the method, the porosimeter may be constructed as well from commercially available components. For simplicity, the apparatus described will be referred to as the "Constant-Pressure gas porosimeter". THE CONSTANT-PRESSURE METHOD Fig. 1 shows schematically the arrangement of components comprising the present Constant-Pressure porosimeter. Briefly, the method is one of volume substitution and may be considered a null measurement. Omitting (for the present) some of the operational details, the method of measurement consists of the following three steps. 1. After evacuation, the volume of the measuring system (a ballast chamber, a manifold, two gauges and their connections) up to the sample chamber is filled with gas to a high pressure (- 1,000 psi). A sample of the gas at this pressure is trapped in one side of a sensitive differential pressure gauge to serve as the reference pressure for subsequent steps. 2. The evacuated sample chamber containing the rock sample is opened to the measuring system. As the gas expands into the chamber, the resulting decrease in pressure unbalances the differential pressure gauge. 3. The pressure is restored by means of a mercury volumetric pump. The volume of mercury injected exactly equals the free or void volume of the sample chamber (volume of empty chamber minus the solids volume of the rock within). From the injected volume and the known empty chamber volume, the solids volume is obtained and the porosity calculated. The pressure and the volume occupied by the gas are the same before and after opening the sample chamber. Expansion and compression of the gas are incidental operations and do not enter into the calculation of porosity. By the pressure balancing or nulling, the free volume of the sample chamber is merely substituted by an equal and measured volume of mercury. Since the measurements are at constant pressure, there are no compressibility corrections necessary for the sample chamber.

By W. Spencer Hutchinson

It is the purpose of this paper to describe a method used to determine the corundum contents of samples of hard crystalline gneiss containing both corundum and red garnet. A chemical analysis of the rock for alumina would not fix the amount of corundum became at least three other constituent minerals of the rock, mica, feldspar, and garnet, contain alumina combined with silica. Following are the principal minerals found in the samples, together with their specific gravity and hardness as given by Dana: The corundum occurred in crystals of a gray or bluish gray color, in minute grains and coarser up to 0.5 in., and no massive or block corundum was observed. The larger crystals were commonly quite slender, well defined, and the normal hexagonal form clearly developed. They lay with the structural planes of the gneiss, and sometimes appeared prominently in relief on weathered surfaces. In some cases these crystals had suffered partial or total alteration to mica, margarite, or other soft minerals, a condition illustrated by sample D, which appeared to be studded abundantly with corundum on the flat faces. Garnet, a striking feature of nearly all the samples, was present in small rounded crystals of a pink to red color. The samples were first broken to pass a No. 4 mesh screen. This was done with a hammer on an iron plate, particular care being taken to avoid the breaking of the crystals finer than need be to pass the screen. A portion of the sample weighing 500 g. was then taken and, with a little water added, was scoured round and round in an iron bucket with a wooden block, until the coarse crystals of corundum were cleaned of adhering pieces of mica. The bucket was then re-

Jan 1, 1914

COLORADO SECTION CHARLES M. MACNEILL, Chairman, GEORGE M. TAYLOR, Vice-Chairman, FRED CARROLL, Sec.-Treas., State Museum Bldg., Denver, Colo. WALTER W. CASE, H. E. COLLBRAN. The annual meeting of the Colorado Section was held on the evening of Jan. 24, at the University Club, Denver, Colo.; SO members and guests were in attendance and the meeting was considered one of the most interesting ever held by the local section. After the usual dinner, the officers whose names are given above were elected for the ensuing year. Dr. David T. Day and Dr. G. H. Clevenger, of the Bureau of . Mines, were present and enlightened us with short talks on oil shales and other work of the Bureau. Mr. J. V. N. Dorr was home from a visit to New York and Washington, and told us something of the war work now going on at our National Capitol. Retiring Chairman Loughridge had been insisting for months that this meeting should be given up chiefly to listening to someone who could give his personal experience in going "over the top" in western France; after a long search he succeeded in finding Sargt. F. C. Strickland, M . M., of the Second Canadian Mounted Rifles, who had very recently been discharged from the hospital with permanent disabilities and has accepted recruiting service rather than a discharge. The success of this plan was evidenced by the close attention accorded the speaker for almost two hours, during which he described conditions, hardships, successes and failures of warfare on the western front. Hardly a listener moved during this talk, and all left with a. feeling that they would have liked to hear more. FRED CARROLL, Secretary.

Jan 4, 1918

By AIME AIME

INSTITUTE members attending the Annual Meeting in New York who want to see one of the mining engineers&apos; newest aids, photoelastic stress analysis, are due for an interesting afternoon on Thursday, Feb. 15, when open house: will be held at the Columbia University mining laboratory. Information as to the direction and distribution off stresses in mine structures, which has been developed by Professor Bucky, associate professor at the Columbia School of Mines, and David Sinclair, research assistant, is useful in the design of pillars and in the placing of openings relative to working places such as gangways and haulage levels.: This work has been sponsored during the last ten years by the Engineering Foundation.. It is fully reported in T. P. No. 1140.

Jan 1, 1940

By Bruce Chalmers, D. C. Larson

Aluminum crystals with longitudinal-axis orientations of (111) . (110), and (100) were deforined in tension and annealed. The conditions of deformation were controlled so that the re crystallization nuclei originated in either the heavily deformed regions at saw cuts {artificial nucleation) or in the lightly deformed matrix (spontaneous nucleation). The artificial-nucleatioln experiments showed that in lightly deformed (110) and (100) crystals low-angle twist boundaries are most mobile, while in (111> crystals and heavily deformed (110) and (100) crystals high-angle tilt boundaries with near (111) rotations are favored. The spontaneous-nucleation experiments showed the existence of preferred orientations in the (111) crystals. The nonrandomness of the grain orientations is quantitatively determined through a comparison with the results which would he obtained from a randowl set of grain ovientations. PREVIOUS recrystallization studies have been performed on single crystals deformed in tension.1 7 The crystals used in these studies usually had random tensile-axis orientations and the extent of deformation was not a primary consideration. The present study concerns the recrystallization of single crystals with tensile-axis orientations of (Ill), (110), and (100). The emphasis of this work is on the influence of the tensile-axis orientation and the degree of deformation on both the nucleation and growth processes. The multiple-slip orientations were chosen because secondary slip or slip intersection promotes nucleation.1,5,8 These crystals recrystallize at lower strains than the crystals which are oriented for single slip. Also, the greatest variation in deformation behavior is exhibited by the multiple-slip orientations. The stress-strain curves for crystals with tensile-axis orientations of (111) are higher than the stress-strain curves for poly-crystals, and the stress-strain curves for crystals with tensile-axis orientations of (100) are lower (at large strains) than the stress-strain curves for the crystals which deform initially in single slip.g The recrystallization nuclei originated in either 1) the homogeneously* deformed matrix of the crys- tals or 2) the heavily and inhomogeneously deformed regions at saw cuts. The nuclei will be referred to hereafter as spontaneous and artificial nuclei, respectively. The two terms do not imply a difference in the nature of the nuclei; they imply simply a difference in the mode of introduction of the nuclei. During spontaneous nucleation very few (always less than ten) grains nucleate, while during artificial nucleation large numbers of grains nucleate. Only a fraction of the artificially nucleated grains penetrate very far into the deformed matrix during annealing. The grains that penetrate the farthest into the deformed matrix will be referred to as the dominant grains. EXPERIMENTAL PROCEDURE The thirty-five crystals used in this investigation were grown from the melt in milled graphite boats at a rate of 1.6 cm per hr. The crystals had dimensions of approximately 6 by 12 by 80 or 6 by 6 by 80 mm and the aluminum was of 99.992 pet purity. The as-grown crystals were annealed at 610°C for 24 hr and furnace-cooled. They were then heavily etched and electropolished in a solution of five parts methanol to one part perchloric acid. The crystal orientations were obtained by back-reflection Laue photographs and were accurate to ±2 deg. The tensile-axis orientations were (loo), (110), and (111). Two of the side faces of the (111) crystals were (110) lanes. The (110) crystals had both {100) and {110) side faces and the (100) crystals had (100) side faces. The crystals were deformed at a strain rate of 0.003 per min. Shear stress and shear strain were obtained by multiplying and dividing the tensile stress and strain, respectively, by the Schmid factor, m. For the (111) crystals m = 0.272 and for the (110) and the (100) crystals m = 0.408. The Schmid factor is effectively constant during deformation for all orientations. The deformed crystals were sawed into 1-in.-long specimens while the crystals were totally enclosed in a graphite boat. The sawing was performed very carefully in order to limit the plastic deformation to the sawed regions. The specimens were electropolished in the solution mentioned above to remove the sawed-end deformation as well as controlled amounts of surface material. A special stainless-steel grip was used to hold the specimens during the electropolishing treatment. The gripping faces were flat, with no teeth, to prevent the introduction of extraneous de-

Jan 1, 1964