Search Documents

By AIME AIME

AN ENGINEER with as varied geographical experience as H. J. Brown does not often specialize on one particular thing all of his professional life. For forty years he has been engaged in gypsum mining, manufacturing, plant design, construction, and operation. Not only is it his work, but he says it is his hobby as well, though membership in three yacht clubs might belie that statement. New England's new representative on the A.I.M.E. Directorate, who was born in New York, Dec. 20, 1879, went to the Lawrence Scientific School at Harvard at the turn of the century. He tried journalism for a year, with the Boston News Bureau and associated financial

Jan 1, 1940

By Wieland D. R., Hurst R. E., A. R. Hendrickson

Analysis of acidizing techniques, in correlation with reservoir data and a backlog of past treatments, has resulted in the development of a valuable engineering guide for planning acidizing treatments. Such treatments fall into three categories: (I) acid injection into the pores of the matrix; (2) acid injection into natural formation fractures at less than parting pressure; and (3) combination acidizing-fracturing treatments in which acid solutions (without propping agents) are injected at treating pressures sufficient to open and extend fractures through which the acid flows. Because the spending tirnze of acid during a specific well treatment does not change appreciably, maximunl penetration is attained when the first increment of injected acid is completely spent. Additional acid injection cannot be expected to further extend the benefits of the treatment. Depth of penetration will depend upon the reaction rate of the acid under treatment conditions, the injection rate of the acid into the matrix or fractures and the area-volume relationship existing in the flow channels. Based on Darcy's flow formula, extremely low injection rates must be used in order to keep bottom-hole injection pressures below formation fracturing pressure. As a result, only limited penetration of unspent acid will occur. Treatment records indicate that, in most acidizing treatments, formation parting pressures are exceeded, greatly extending acid penetration. Under these conditions, stimulation benefits are limited to the fracture area produced during the spending time of the first increment of acid injected into the formation. This area may be calculated from laboratory and well data to estimate depth of penetration. This, in turn, may be correlated with productivity data to assist The art of gas and oil well acidizing has been characterized by many changes in treating materials and techniques since its inception. These developments have been designed to provide greater production increases. prolong production declines and shorten payout time. Such improvements have been based primarily on data derived from laboratory research and field experience. As more of the variables influencing these treatments have been recognized and evaluated, acidizing has become less of an art and more of a science. Recent studies of fracturing treatments,' in light of individual well conditions and the results of thousands of fracturing treatments, made possible the formulation of an engineering guide that is now being used to select optimum treating techniques and to forecast probable results of such treatments. A similar analysis of the factors controlling acidizing treatments has been made and is the basis for this paper, The findings herein can be used as a guide in the selection of acidizing solutions and techniques, tailored to fit specific well conditions and to provide optimum stimulation per dollar cost. Acidizing treatments may be classified into three basic categories—(1) treatments in which the acid is injected uniformly into the pores and flow channels of the matrix, (2) treatments in which the acid enters natural fissures and fractures in the formation at less than fracturing pressures and (3) injection of acid into the formation at a pressure sufficient to open and extend fractures into the rock through which the acid penetrates (without the inclusion of a propping agent). TYPE 1 — MATRIX ACIDIZING This category consists of treatments in which acid solutions are injected into a homogeneous carbonate

By H. O. Jahns

This paper describes the application of regression analysis for obtaining a two-dimensional areal description of heterogeneous reservoirs from short-term pressure-time data such as that obtained in interference tests. The method replaces the time-consuming trial-and-error procedure commonly used to match field data on an electric analyzer or digital computer with a systematic search which is programmed for a computer. The computer program adjusts the properties of a reservoir model automatically until a least-squares fit is obtained between observed and calculated pressure data. The reservoir is simulated by a single-phase, compressible, two-dimensional model. It is divided into a number of homogeneous blocks whose transmissibility (kh/F) and storage (Fch) values are varied to obtain the least-squares fit. The reliability of these values is determined from their standard deviations and correlation coefficients. Although the method is rigorously applicable to single-phase flow only, multiphase flow can be handled provided saturation changes are small during the test. Possibly the method can also be used to obtain a reservoir description from pressure-production history, but this application is outside the scope of this work. The paper includes, in addition to a description of the numerical procedure, a discussion of some of the problems associated with the method. Rules are given to help in selecting the number of homogeneous blocks and deciding upon their arrangement. The uniqueness of a reservoir description is considered. Finally, the use of the method is illustrated by the interpretation of field data from two interference tests. INTRODUCTION Pressure data from short-term transient tests, such as single-well and interference tests, are widely used to obtain reservoir properties. These tests are usually analyzed by assuming a simple reservoir model; very often, a homogeneous one is used. As a result, analysis of the transient data from each well frequently gives different values for reservoir properties. The problem then arises to combine all these differing results into a more detailed picture of the reservoir. One technique is to simulate the reservoir with a digital computer or with an electrical analyzer and to adjust the reservoir parameters by trial and error until the simulated pressure data are in reasonable agreement with the observed pressure data for all wells. Although this method has been used for both transient tests and pressure-history data, it is time-consuming and subjective. A second technique uses regression analysis to replace the trial-and-error procedure with a systematic search that can be programmed for a digital computer. Use of regression analysis in reservoir description was proposed recently by Jacquard and Jain.1 They divided the reservoir into a number of homogeneous blocks whose properties are varied until a least-squares fit is obtained between observed and calculated pressures. However, they did not consider their technique to be operational, mainly because of ".. .(I) the lack of experience in using the method .. . notably for the improvement of convergence; and (2) limitations imposed by the insufficiency of available computers". 1 While the analysis presented in this paper applies the same general principle used by Jacquard and Jain, the specific method is significantly different. Some differences are (1) the regression problem is solved in a different way which requires less computer time in most cases; (2) a stepwise solution, in which the detail in the reservoir description is increased from step to step, is used to improve convergence; and (3) the reliability of the estimated reservoir .properties.. as measured by their standard deviation and correlation coefficient, is estimated'

Jan 1, 1967

By T. F. Bower, M. C. Flemings, H. D. Brody

A series of experiments are reported which show thai reasonable assumptions for analysis of solute redistribution in solidification of castings and ingols illclr(de: negligible undercooling before nuclcation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the Liquid oer distances the order, of dentrite arm spacings, platelike dentrite t/o?$holog?.. Qzmli/ali,e and periment is obtained JOY Al-Cu alloys front measurements of amount of nonequilibrium second phase, minimum solute content at the centers dentrites arms (after solidification), and 3) change in minimum solute content in dentrite arms during solidification. In a previous paper' analyses were given describing solute redistribution in dendritic solidification. The analyses were undertaken primarily to permit prediction of "severity of microsegregation" in a casting or ingot after solidification and cooling to room temperature, but can also be used to predict "local fraction solid' as a function of temperature in the solidifying alloy. Numerical results were given for Al-Cu alloys. The aims of this paper are to examine the validity of some of the assumptions of that analysis, and to compare predictions of the theory with experiments. All experiments reported are on Al-Cu alloys, the bulk on Al-4.5 pct Cu alloy. EXPERIMENTS Experiments conducted were on small ingots, 41/2 in. in diam by about 10 in. high. solidified in a controlled thermal environment (i.e., in a resistance-heated, re-circulating air furnace, whose temperature could be controlled to 1°C). In one series of experiments, the ingots were solidified very slowly (solidification time was varied from 8 to 1000 hr) and at constant rate of heat extraction. In a second series of experiments the ingots were solidified ( 'unidirectionally". Fig. 1 is a sketch of the method of making the two different types of ingots. The unidirectionally solidified ingots were fully columnar, and the slowly solidified ingots had equiaxed structures, Fig. 2. In making the slowly solidified ingots, the mold employed was carbon steel, coated with inert refractory. Typically the mold and its environment were heated to 700°C. The molten alloy was then poured into the mold and the temperature of the system equilibrated above the liquidus. The environment of the mold was next cooled with a controller responding to a differential thermocouple that measured the difference between the temperature of the melt and the temperature of the mold environment. The differential thermocouple consisted of one chromel-alumel junction in the melt connected in opposition with a second junction in the furnace. The potential across the differential thermocouple was input to the controller which acted to keep this potential at a set. constant value; hence the temperature difference between the two junctions was maintained nearly constant. Major resistance to heat flow in the above apparatus was between the metal surface and the furnace atmosphere, not in the metal itself. By maintaining a constant temperature difference between the metal and the furnace atmosphere, the controller maintained an essentially constant rate of heat extraction during solidification, regardless of amount of heat released by the metal per unit temperature change. When the metal temperature dropped just below the eutectic temperature. the ingot was removed from the furnace and water-quenched. The unidirectionally solidified ingots were cast in a similar mold to the foregoing except that provision was made to extract heat through the bottom face of the mold by passing air or water through the mold base, Fig. 1. For these experiments, metal and mold temperature were again equilibrated above the liquidus. Temperature of the mold environment was then held

Jan 1, 1967

By J. T. Dewan

An experimental setup is described whereby the responses of Neutron logging instruments have been determined opposite formations of different porosities and under various borehole conditions. The results of these tests are presented in several charts which show how the Neutron log is affected by the following factors: hole diameter, casing, cement, salinity and weight of drilling mud, and position of logging tool with respect to the wall of the hole. The responses in the case of empty holes are also shown. A chart is furthermore presented which shows the shapes of the Neutron log, as a function of logging speed and time constant, at the boundaries between two formations with different porosities. These were derived mathematically using as a basis laboratory determination of the shape of the curve under static conditions, i.e. at very low logging speed. Corrections for the readings made opposite thin beds are given by these computations. The correction is found negligible under usual logging conditions for beds thicker than about 4 ft. INTRODUCTION The Neutron log is used in borehole surveys both for the delineation of porous formations and for the quantitative estimation of their porosities.1,2,3,4,5 It is common practice to calibrate the response of the Neutron log in terms of porosity values for each given geological unit by means of empirical comparisons between the deflections of the neutron curve and the porosity values given by the core analysis in a sufficient number of wells. Usually, the plots of the porosity values vs Neutron log deflections show a definite trend. It is therefore possible to trace an average line across the plotted points. This average line constitutes a calibration curve which can be used to evaluate the porosities from the Neutron logs in the other wells drilled in the same region. Futhermore, when the porosity values are plotted on a logarithmic scale and the Neutron log deflections on a linear scale, the calibration curve is practically a straight line. Accordingly the calibration curves are often determined by simply tracing a straight line between two points corresponding to two widely different porosities. Different choices are made for these two points, depending on local conditions. For example, one point will be defined by plotting the deflection of the Neutron curve opposite a formation known to be very tight, for which an average porosity value of 1 or 2 per cent is assumed. The other point may correspond to shale sections, to which a porosity of around 40 per cent is ascribed. The information provided by the eletrical logs — in particular the Laterolog, Limestone log or Micro-Latero-log — is also very often a help in the calibration of the Neutron logs. Empirical approaches such as these make possible the derivation of fairly reliable porosity values from the Neutron logs in many cases, at least in open holes and in essentially clean formations. There are, however, several causes of uncertainty which may sometimes entail appreciable errors. On the one hand, the Neutron log readings are influenced by the borehole conditions: hole diameter, presence or absence of casing and cement, presence or absence of drilling mud, characteristics of the mud, and position of the logging instrument with respect to the wall of the hole. The amplitudes of the curves opposite thin beds are furthermore atfected by the bed thickness,

Jan 1, 1957

By E. DeGolyer

PROSPECTING for new deposits is a part of the ordinary routine business of the petroleum industry to an extent that is not true for any other mineral industry. The health of the industry depends upon whether we are successful or unsuccessful. How many know what it costs to find oil today and what it has cost in the past? Very few, I will wager. The industry is not well informed upon this extremely important point. We cannot deal in averages for lack of information. Does it cost more or less than previously? Prospect wells are increasingly deeper and, since the introduction of the core drill, prospecting techniques have required increasingly expensive field oper-

Jan 1, 1939

By B. A. Eaton, R. H. Jacoby

This paper presents the depletion-performance correlations developed using data from PVT studies and well-completion tests of 27 rich gas-condensate and volatile-oil reservoir fluids. The PVT behavior for each fluid war determined experimentally in the laboratory, and the depletion performance of each fluid was then calculated. Well-completion test data consisting of reservoir pressure and temperature, initial total gas-oil ratio, and stock-tank oil gravity were used with the depletion-performance data to develop general performance correlations. Three correlations are presented. The first equation shows the empirical relation of gas in place per barrel of hydrocarbon pore space with reservoir pressure and temperature, and initial total gas-oil ratio. The second equation is the correlation of stock-tank oil in place per barrel of hydrocarbon pore space. The third equation relates stock-tank oil production (to 500-psia depletion pressure) with pressure, temperature and oil gravity. All three correlations are also presented in convenient graphical form. Gas production to 500-psia depletion pressure is approximately 92.6 per cent of the gas in place for each fluid, so no correlation was developed for gas production. INTRODUCTION The rate of discovery of shallow, low-pressure and low-temperature oil reservoirs in the United States has been declining in recent years. For this reason, the search for oil has gone to greater depths where high pressures and temperatures are encountered. A high-pressure and high-temperature reservoir is the environment in which many rich gas condensates and highly volatile oils are found. Because of this trend, the performance prediction of such reservoirs has become an important task of the reservoir engineer. The need and usefulness of a performance correlation based on field data that are available from the usual well-completion tests have previously been established. These earlier attempts have shown that the phase behavior of rich gas-condensate systems and volatile-oil systems can be correlated with fluid properties, pressure and temperature. However, very little information on gas-condensate depletion performance5 was available at the time of these earlier attempts. The availability of more recent data has made possible the development of an improved correlation. The data, as listed in Tables I and 2, are for 25 gas-condensate and two volatile-oil systems that were studied. The problem was to correlate the data for in-place fluids and the production data with the initial total gas-oil ratio, initial reservoir pressure and temperature, and stock-tank oil gravity. These correlations were obtained by multiple regression analysis, whereby the data were fitted to an equation by the method of least squared error. BASIS OF THE CORRELATIONS 1. The data used in the development of these correlations were obtained from depletion-performance calculations6 and well-test or production measurements. 2. All of the independent variables used in the correlations are available from the usual well-test completion data. 3. The reservoir volume considered is 1 bbl of hydrocarbon pore space (HCPS). 4. The gas-oil ratio used is the total standard cubic feet of gas (at 14.7 psia, 60F) coming off the entire separator train per barrel of stock-tank oil. This minimizes the effect of separator conditions which might vary from system to system. 5. The correlated pressures are the actual reservoir pressures which might or might not be the saturation pressure of the reservoir fluid.

Jan 1, 1966

By N. J. Grant, B. C. Giessen, R. Koch

The system Nh-Ir was investigated over the complete concentration range by metallography and X-my techniques, using forty one alloys. The solubility limits of terminal and intermediate phases and the solidus temperatures were determined. Five intermediate phases were found: a Nb3Ir, cubic, Cr3O type; tetragonal, ofecr thorhomhic, isostruc-turn1 with (ta-Rh); and a Nhlr3. cubic, AuCu, type. a Nb3lr and a Nbfr3 melt congruently; three eutectic and three pentectic reactions occur. The phase diagram of the Nb-Ir system had not been fully treated in the literature; only surveys of intermediate phases were found.1"5 In this study, the details of the phase boundaries were investigated as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS The experimental procedures such as arc melting of powder compacts, heat treatments, solidus measurements, X-ray, and metallographic observation were identical with those used in the work on the Nb-Rh phase diagram.&apos; They will therefore not be repeated here except where the conditions differed. The purity of the niobium powder was as stated in Ref. 6; the iridium powder of 99.9+ pct purity from J. Bishop and Co., Malvern, Penn., did not contain impurities exceeding 100 ppm, except rhodium (200 ppm). The melting points and vapor pressures of both elements are very similar. This fact contributed to a very small weight loss on melting and facilitated preparation of homogeneous alloys. As shown in Ref. 6 for Nb-Rh, no oxygen pick-up exceeding 200 ppm had to be considered; this was regarded as valid also for Nb-Ir. A total of forty one alloys were used in the determination of the phase diagram; their concentrations are shown in Fig. l, which presents the phase diagram. The concentration limits as determined by the weight-loss method averaged <0.2 at. pct, and never exceeded 0.5 at. pct. Heat treatments were carried out as described in Ref. 6. Depending on the concentration, only tantalum, tungsten, or iridium containers were employed, avoiding oxide crucibles altogether. Alloys from 0 to 25 and from 65 to 100 at. pct Ir were homogenized at 2095°C for 15 hr, intermediate compositions from 25 to 65 at. pct Ir for 65 hr at 1780°C. A typical annealing-time schedule is presented in Table I. Solidus points were measured as described in Ref. 6 with the modification that samples rich in niobium were held between pieces of tantalum foil and samples of high iridium concentrations were held between rhenium platelets or in iridium wire. After each run it was ascertained metallographically that no reaction with the holder had occurred. Rhenium was selected as holder material after it had been shown in separate tests that the melting points of Re-Ir alloys rise continuously from 2440°C. Metallographic examination was carried out as described in Ref. 6, and the same procedure and etchants were used successfully. While metallographic discrimination between a Nb3lr and o was easily possible, X-ray diffraction was necessary to separate al and ct2. X-ray powder patterns were taken and evaluated as for Nb-Rh6 yielding the error limits indicated in Table 111, to be introduced later. For the determination of the invariant reactions and phase boundaries, the same techniques as for Nb-Rh6 applied. The general accuracy of invariant concentrations is regarded as somewhat higher than for Nb-Rh due to the small slope of most solvus lines.

Jan 1, 1964

By M. Garfinkle, W. D. Klopp, W. R. Witzke

The tensile properties of binary W-Re alloys containing up to 33 at. pct Re were determined at temperatures from 78" to 3630°F. Elongations as high as 260 pct were observed in electron-beam-melted tungsten containing 23 at. pct Re when tensile-tested at 3630°F after a 1-hr anneal at 3090°F. All alloys tested under these conditions with rhenium contents between 20 and 28 at. pct exhibited elongations of at least 200 pct. These alloys also showed enhanced grain growth rates. The values of strain-rate sensitivity ranged between 0.2 and 0.3 for the alloys exhibiting high elongations. Houlezler, for swaged alloys tested just above the re-crystallization temperature, strain-rate sensitivities as high as 0.8 were observed. The high-temperature strengths of the high-rhenium-content alloys were also less than those of alloys with intermediate rhenium contents. ALLOYING with rhenium has two distinct effects on the mechanical properties of tungsten. One effect occurs in dilute solid solutions and is most clearly seen in the lowering of the hardness and of the ductile-brittle transition temperature at about 5 at. pct Re.1-3 The second effect occurs in the concentrated solid solution at about 25 at. pct Re, and is characterized by twinning and a larger decrease in the ductile-brittle transition temperature. An aspect of the high-rhenium-content alloy which has received little attention is the higher-than-usual tensile ductility at 3500°F.3 Anomalous high ductility has been observed in several other alloy systems. usually associated with a phase transformation or a solid-solubility limit.4&apos;5 The phenomenon is now commonly termed superplasticity. High-strain-rate sensitivities6 and grain boundary sliding7 have been reported for materials that undergo superplastic deformation. Also, it has been found that superplastic materials usually have a very fine grain structure (less than 10 pm).8 and it has been proposedg that such a structure alone is sufficient for superplasticity. The purpose of the present study was to further characterize the high-temperature tensile properties of W-Re alloys to determine the conditions under which they might be superplastic. Tensile and selected strain-rate sensitivity tests were conducted on alloys containing 0 to 33.3 at. pct Re at temperatures from 78" to 3630°F. Grain-growth rates were also determined on most alloys at 3630°F. Fig. 1 indicates the compositions evaluated and their locations relative to the solvus line in the tungsten-rich end of the W-Re phase diagram. Twelve binary W-Re alloys containing up to 33.3 at pct Re were double electron-beam-melted and subsequently fabricated to 0.3-in. rod by extrusion and swaging. The starting materials were commercial powders of tungsten and rhenium with impurity levels as listed in Table I. The various blended W-Re compositions were hydrostatically pressed at 70 ksi. The pressed bars were drip-melted into 1.5-in.-diam ingots and then remelted into 2-in.-diam ingots at a chamber pressure of 10~5 torr. The ingots were canned in molybdenum and extruded to round bar at a reduction ratio of 6:l. The alloy extrusions were swaged to about an 80 pct reduction at 2100" to 2900°F. Buttonhead tensile specimens with a reduced section diameter of 0.16 in. and a gage length of 1.0 in. were centerless-ground from the swaged bars

Jan 1, 1970

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2&apos;4&apos;5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.&apos; Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a&apos; range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.&apos;

Jan 1, 1955

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies&apos; was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By M. A. Torcaso, P. Raimondi

To study mass transport in systems simulating oil recovery processes, different porous media were saturated with a mobile (carrier phase) and a stationary phase. Slugs of carrier phase containing a small amount of solute were displaced with pure carrier phase. By analogy to the chromato-graphic processes, the velocity of the solute can be predicted from a knowledge of the partition coefficient and the saturation provided that equilibrium between the two phases exists. Equilibrium was found to exist for different porous media, solutes and rates. The conditions were varied over the range normally encountered in the laboratory and in the field. The longitudinal dispersion of a solute undergoing interphase mass transfer was also investigated. INTRODUCTION The production of hydrocarbons by gas cycling, enriched gas drive and C02 or alcohol displacement involves, among other factors, relative motion between two phases and compounds, hereafter called solute, which are soluble in both phases. The solute is carried forward by the faster flowing phase at a lower velocity than the average velocity of that phase. Retardation of the solute is caused by chromatographic absorption and desorption in the slower flowing phase and by the degree of departure from equilibrium. At equilibrium the concentration of solute in the two phases can be related by the equation* CSw = K Cso ,............(1) where C, and C are the concentration of solute in the aqueous and oleic phases respectively and K is the equilibrium ratio, or partition coefficient. Displacement theories must contain an explicit assumption with regard to equilibrium, i.e., whether the compositions can be related by Eq. 1. The existance of equilibrium depends, in general, on the relative velocity between the phases. Unfortunately, other factors such as gravity segregation and viscous fingering, also depend on velocity. For this reason, whenever effects of rate on displacement were observed,2-4 it was practically impossible to discern what caused them — lack of equilibrium or the factors mentioned above. Equilibrium between phases has been the subject of extensive studies in fields such as extraction or chroma to graphy. It has received only small attention in flow through the type of porous media encountered in oil production.5 For this reason a method was developed which makes it possible to study the movement of a solute as it is affected by rate, type of porous media, partition coefficient and carrier phase, but in the absence of segregation or fingering. The information obtained enables one to determine when the assumption of equilibrium can be made. Briefly, the method consists of (1) saturating the core with a mobile and an immobile phase, (2) injecting a slug made up of the same fluid as the mobile phase and a small concentration of mutually soluble solute, (3) measuring the lag and the peak height of the slug at arrival and (4) correlating these variables with fluid properties such as partition coefficient and mixing constants of the medium. PROPOSED MECHANISM The principles of chromatography are combined with the equation of longitudinal mixing to predict the velocity of a solute slug compared to the bulk velocity and the peak height of a slug.6-9 The equation so obtained is valid under equilibrium conditions only. Therefore, a comparison between experimental and predicted results will give a measure of departure from equilibrium. This work was done with either the oleic or the aqueous phase being immobile. For simplicity, the following development is based on the case where the oleic phase is immobile. However, the treatment is the same in either case.

Jan 1, 1966

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.&apos;, &apos; One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.&apos; The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

Charles H. White, Harvard University, Cambridge, Mass, (communication to the Secretary*):—In answer to Mr. Jar-man&apos;s questions I am able to say that constant use (during term-time) since 1901 has shown the new appliances in our laboratory to be very satisfactory. The draft in the hoods is sufficient to lift the fumes promptly from the baths and hotplates ; and the occasional application of stove-polish,—usually about three times a year, at the recess-periods,—so well protects all iron-work in the hoods that, up to the present time, there is very little evidence of the corroding action of acid fumes. Iron should never be used in the construction of hoods above

Jan 1, 1906

By Jacques Steininger, Robert E. England

Single crystals of ZnTe and ZnTe1-,Sex with x up to 0.13 have been grown from the elements by temperature gradient solution zoning using excess tellurium as a solvent. Best results have been obtained with charges with the compositions 45/55 at. pct Zn, Te, for ZnTe and increasing amounts of selenium for ZnTe1-xSex. The temperature in the molten zone was maintained at about 1070°C with a gradient of about 10°C per cm. Chemical analyses of quenched ZnTe ingots show tellurium concentrations in the molten zone as high as 70 pct with concentration differences across the zone of 1 to 2 at. pct Dark dots which are observed by transmitted light microscopy in as-grown crystals can be removed by annealing in zinc vapor at 900 C. INTEREST in wide band gap semiconductors has led to a new study of ZnTe and ZnTel-xSex crystal growth. ZnTe is the only II-VI compound with a wide band gap (2.3 ev) that can be made p type with low resistivity. Attempts to make it n type with low enough resistivity to be useful for p-n junctions have so far been unsuccessful.1 ZnSe has a band gap of 2.65 ev but can be made n type only. However, ZnTel-xSex solid solutions with x as low as 0.36 have been made both highly n and p type2 with a minimum band gap around 2.12 ev3 at room temperature and appear to hold the best promise for efficient injection electroluminescence in the visible. ZnTe has the lowest melting point of the zinc chal-cogenides (1295°C) and consequently attempts have been made to grow crystals from both the liquid and the vapor phase.4 Complicated apparatus is required for growth from stoichiometric melts because of the high vapor pressures of the elements at the melting point of ZnTe and because of the problem of quartz devitrification. Small crystals have thus been grown in high-pressure equipment by Fischer5 and by Narita et a1.6 with pressures of the order of 50 atm of argon to prevent excessive evaporation from the melt. Large crystals of ZnTe can be obtained by growth from the vapor phase4 but they often present numerous dislocations and inclusions. An improvement in the quality of vapor- grown ZnTe crystals was reported by Albers and Aten7 by equilibration of mixtures of small crystals with compositions lying on either side of the solid single-phase field at fixed temperature. The same technique was later applied by Aten8 to the growth of ZnTe1-xSex crystals with less than 1 pct inhomo-geneity. Because of the higher liquidus temperatures of the solid solutions and the high vapor pressure of selenium, previous attempts to grow ZnTel-xSex from the melt have been limited and unsuccessful.9 The phase diagram of the Zn- Te system is reproduced in Fig. 1, based on data from Kobayashi10 and Kulwicki.11 Carides and Fishher12 have reported lower liquidus temperatures on the tellurium-rich side, but their data would require confirmation. The liquidus temperature on the tellurium-rich side decreases rapidly with increasing tellurium concentration and the Te2 vapor pressure over the liquidus also decreases accordingly.&apos;3 The decrease in liquidus temperature and vapor pressure therefore makes it possible to use conventional apparatus if there is a sufficient excess of tellurium in the melt. Single crystals of ZnTe have thus been grown by Kucza,14 in a modified Bridgman technique, from solutions containing up to 60 at. pct of Te by lowering unsupported quartz ampoules through a temperature gradient at about 1200°C. Under these conditions, the phase diagram indicates that the entire charge is initially molten. Crystal growth can therefore proceed by normal freezing and rejection of excess tellurium into the melt. The modified Bridgman technique has several major limitations. Because of the rejection of excess tellurium into the melt during freezing, the melt composition and the temperature at the growth interface vary continuously. They tend to follow the liquidus until the eutectic which is very close to pure tellurium (447°C, >99 pct Te). Since the solidus composition also varies with temperature,15 crystals grown by this method are inhomogeneous. They present small variations from stoichiometry which may affect their structure and physical properties. The simultaneous increase in tellurium content and decrease in melt temperature also combine to reduce the rate of diffusion of tellurium away from the growth interface, thereby causing constitutional supercooling and possibly dendritic growth. To minimize these effects, the initial melt composition is in practice kept relatively close to stoichiometry (less than 60 pct Te). This however limits the possibilities of operating at low temperatures and pressures. This paper describes a modified method of crystal growth by temperature gradient solution zoning (TGSZ) which is an adaptation of the temperature gradient zone-melting technique developed by pfann16 and of the traveling solvent method of Mlavsky and weinstein.I7 The TGSZ method now applied to the growth of ZnTe and ZnTel-xSex crystals is characterized by its very simple experimental arrangement and sample preparation technique. Unlike the modified Bridgman technique, there is no increase in the tellurium concentration in the melt and therefore it is possible to operate at lower temperatures and pressures. This method is also suitable for maintaining a constant temperature at the growth interface.

Jan 1, 1969

By Harry L. Brown, Philip E. Armstrong

Young&apos;s modulus doto ore presented for W, Mo. Ta. V, Cr. Ni, Ti, and Zr as a function of temperature up to about 0.7 of the melting points. A plot of reduced temperature us reduced modulus produces a general correlation except for titanium and zirconium. Young&apos;s modudlus data for some representatiue commercial graphites are given up to 2400°C. All results were obtained from longitudinal resonance-frequency measzrrements of 4-in. long samples, corrected for simultaneously measured thermal expansion. Comparison of poly crystalline and single-crystal tungsten behavior indicates that all the observed modulus values are frequencv -dependent at the higher temperatures. STATIC measurements of elastic properties of materials at elevated temperatures are extremely difficult to make since the elastic behavior is obscured by relatively large first-stage creep effects. Dynamic methods which avoid this difficulty by utilizing the measurement of the resonance frequency of a simple vibrational mode have been described in the 1iterature.l-3 The authors have extended the operating temperature range of this type of measurement to above 2000°C and have described the equipment elsewhere.~ The Young&apos;s modulus data presented here were obtained with this equipment, using samples about 4 in. long and 1/4 in. diam, supported horizontally at the center and excited to the fundamental longitudinal resonance frequency. Young&apos;s modulus was calculated by the formula: E = 4f2f2p where E = Young&apos;s modulus, / = frequency, 1 = length, and p = density. Dilatometric data were obtained simultaneously by optical measurements of the change of length of the sample. For the metals tested, an attempt was made to obtain modulus values that would be representative of the pure, strain-free, randomly oriented material. All of the graphites studied exhibited a high degree of elastic anisotropy, while the method assumes an isotropic homogeneous material. However , when the values for Young&apos;s modulus obtained for AUC graphite were compared with those taken from static measurements at room temperature they were found to be only about 4 pet higher. This is excellent agreement considering the low precision of modulus calculations from stress-strain curves. The difficulty in using data of apparent Young&apos;s modulus for anisotropic materials arises when the attempt is made to use these data and shear-modulus data to obtain Poisson&apos;s ratio. The results are usually meaningless and sometimes absurd.&apos; RESULTS Table I lists the sources, impurity content, thermal history, and dilatometric constants of the metal samples that were investigated. All the metal samples were tested under a vacuum of 1 to 5 x 10-5 Torr. Where our dilatometric data agreed with previously published data, the table lists the previous values and the literature reference. Where no reference is given, the constants were determined from our dilatometric data. Table II presents the modulus data in units of millions of psi as a function of temperature in degrees centigrade. The numbers were obtained from curves fitted to the experimental data. For some types of calculations, such as those attempting to correlate creep data, the slope of the modulus curve is of interest, and this information also is reported in Table 11. It is always tempting to try to fit physical-property data into some general pattern and then use this pattern to predict the behavior of other similar materials. The general pattern for an elastic modulus of a metal seems to be a linear deoro- with increasing temperature Over the range between 0.1 and 0.4 of the melting temperature, then a progressive1y decreasing value up to the melting point. Metals appear to retain finite moduli

Jan 1, 1964

By J. E. Tobey

THERE are a lot of good things about this great industry of ours. Let us stop commiserating and consider some of the things that are right in this business. Coal is number one in the basic material industries. Our civilization owes more to it than to any other basic commodity. We are literally immersed in the benefactions of coal. In cur man-made world it is indispensable and we are constantly surrounded by objects, materials, and services which owe their existence to coal. Practically all the important materials, such as iron, steel, brick, cement, lime, rubber, glass, cotton, and wood have felt its magic touch.

Jan 1, 1939

By Allan D. Taylor

INTRODUCTION From the designer&apos;s view, the installation starts with the first definition of the orebody, and progresses through a long and complex development. The design is affected not only by the characteristics of the ore, but by all of the personalities and events of the project during its development. The following discussion attempts to touch on the most important aspects which define the context in which the designer must work in apply the do&apos;s and don&apos;ts. That context is the basis of the viewpoint. WHAT CAN GO WRONG The Project Is Going Over Budget This is a common and serious concern to the plant designer. The Project Falls Behind Schedule Another common and disturbing condition with which the plant designer must cope. Some Equipment Fails to Perform This can be due to either faulty equipment or operating deficiencies. It can be the result of a wide variety of causes, but the designer will be an interested party in the search for the cause and the cure. The Plant Isn&apos;t Flexible Enough Sometimes a plant will handle some or even most of the ore satisfactorily but is unable to treat another type properly. This can be a significant problem. An example might be a case where low capacity of a cyclone feed pump makes it impossible to accompany an increase in grinding mill throughput with a corresponding increase in dilution water. This could lead to an increase in cyclone feed density, and a loss in product grade or a limit on the plant capacity. Spillage And Cleanup Are Excessive This is one of the most common and annoying defects in metallurgical plants, and one for which the designer can rarely delegate blame. Maintenance Is Excessive Another common complaint in new plants, and also one for which the dedesigner must accept most of the responsibility.

Jan 1, 1982

By S. Mukai, Y. Shah, T. Zshikawa, T. Wakamtsu

In order to recover coal concentrate of low ash and low iron content, the electrostatic separation of coal was studied. It is more successful in the corona discharge field to recover the coal concentrate of low ash and low iron content than in the field without corona discharge. The effect of humidity on the electrostatic separation of coal was then studied. From the experimental results, it was clear that the electrostatic separation was excellent in about 60% relative humidity of atmosphere. Thus, the separation of vitrite from coal is practicable by electrostatic separation. In recent years the demand for high quality coal containing low ash, low iron, and low sulfur has increased. To fulfill this requirement, a higher grade coal concentrate must be produced. Study on the electrostatic separation of coal has been performed for several years in the author&apos;s laboratory. From the results of this research, it was considered that the behavior of coal particles in the electrostatic field relates closely to the ash and iron content in coal. In the present paper, the electrostatic separation of coal in corona discharge field was studied in order to recover the high quality coal concentrate and then the effect of humidity on the electrostatic separation was investigated. PREPARATION OF COAL SAMPLES The coals from the Akabira mine, the Kushiro mine, the Miike mine, and the Oshima mine which are famous coal mines in Japan were used in this study. The ash contents of these coals are shown in Table I. From the results of the analysis of the coal samples by the Norelco X-ray diffractometer, it is recognized that the Miike coal includes mainly pyrite, quartz, kaoline, calcite, and epidote; the Kushiro coal: kaoline, quartz, and montmorillonite, and the Oshima coal: siderite, dolomite, and other substances. For the preparation of samples, the coarse pieces of coal were crushed to about 2 mm in diam and then ground in an agator mortar. The ground products were sieved and fractions of 10 — 14 mesh, 14 — 20 mesh, 20-28 mesh, and 28-35 mesh were prepared, respectively. APPARATUS OF ELECTROSTATIC SEPARATION The principal part of the apparatus of the electrostatic separation used in the experiments is shown in Fig. 1. In order to generate the corona discharge field, a needle-shaped electrode combined with a pole electrode is installed as the high tension electrode. In the case of investigating the effects of the humidity on the electrostatic separation of coal, the needle-shaped electrode was combined with a plate electrode instead of the pole electrode as shown in Fig. 2. The pole or the plate electrode was installed to promote the repelling of the charged particles by producing the electrostatic field between this electrode and the grounded roller. It seems to be very useful on the coal separation to install these combined high tension electrodes. SEPARATION OF COAL PARTICLES IN CORONA DISCHARGE FIELD The separation testings on the coal samples in the corona discharge field were performed by the apparatus as shown in Fig. 1. These experiments were carried out under the following conditions: feed size 20 — 28 mesh, room temperature, normal humidity and applied voltage 15-20 KV, and the combined electrodes including the needle-shaped electrode were negatively charged. The results of these testings are

Jan 1, 1968