Search Documents

By G. Y. Chin, W. F. Hosford

It has long been recognized that, for a crystal to undergo an arbitrary shape change by crystallographic shear, at least five independent shear systems must be activated. Taylor1 analyzed the deformation of fcc crystals by {111}<110> slip and showed that the principle of minimum work could be used to determine which combination of slip systems might act to produce a given shape change. Later Bishop and Hi112 attacked the same problem by first identifying the state of stress which could physically activate five or more {111)(110) systems simultaneously and then invoking the principle of maximum virtual work to determine which combination would act for a given shape change. Taylor&apos;s general approach has been used to calculate the active slip systems and the relative strengths during axisymmetric flow of cubic crystals with other deformation modes, including {112}<111> slip3 and {111}<112> twinning.&apos; It is the purpose of this note to identify the stress states capable of activating simultaneously five or more of these systems. {111}<112> Twinning. The {111}<112> systems are defined in Table I and illustrated in Fig. 1. The sense of the shears are those for twinning in fcc crystals. The shear stress on any system may be written in terms of the stress components expressed relative to the 1,2,3 cube axes. For example, the stress For five or more of the systems ij to be activated simultaneously, it is necessary that Tij/T be equal to unity in at least five of the expressions [3], while Tij < T for the remainder. (These restrictions assume that the same shear stress T is required to activate each system and that the shear stress on any system cannot exceed that for its activation.) The discrete values of the stress components A through H which can satisfy these restrictions are listed in Table II together with the values of Tij/T for all systems. It may be noted that Tij/ T is not necessarily zero on all nonactive systems as found by Bishop and Hill for <110> {111} slip. In fact, for the case of twinning Tij/T may reach negative values as large as -2 for shear stress in the reverse direction, Table 11. This means that, if those stress states are to be valid, the shear stress to activate reverse twinning must be greater than twice that for forward twinning. Such stress states are probably valid in view of the directionality of the twinning process. There has been no documentation of reverse twinning thus far. It may be noted that the stress states fall into four classes, which may simultaneously activate eight, six, six, and five twin systems respectively. These solutions may be applied to the {112}(111)

Jan 1, 1970

By William G. Pariseau

The flexure of geologic strata, a phenomenon of interest to geologists and mining engineers alike, is examined as a sheet bending problem in Coulomb plasticity. Fonnulae for the distribution of stress, strain, and displacement increments; volume change; change in the length of the central surface; and power of dissipation, as well as for the neutral surface shift are given. Strains of any magnitude are considered. The analysis shows that deeply buried strata may bend and develop "tensile" cracks under generally compressive states of stress. It is also shown that bed separation and high capacity props are desirable in mechanized longwall mining, a result in keeping with operating experience. Although speculative at this time, the analysis provides a rational working hypothesis as regards the problem of strata flexure and control. | he purpose of this paper is to present an analysis of the flexure of geologic strata as a problem in the bending of a sheet of material failing in accordance with a Mohr-Coulomb criterion. The flexure of strata has an obvious academic interest to the geologist concerned with the mechanics of folding. It is of interest to the economic geologist as it relates to the structural control of certain types of ore deposits. It has an intimate association with mine subsidence phenomena, and is of concern to the mining engineer. Strata flexure is also the dominant feature of roof behavior about longwall workings. An improved understanding of strata flexure through a rational mechanical analysis thus appears desirable not only from the academic view but from the economic one as well. In the field, the most commonly observed feature of folding, subsidence, and longwall roof behavior is the permanent and therefore inelastic nature of the strata movement. Fig. 1 illustrates the physical disposition of strata in the vicinity of a longwall face. Inasmuch as most rocks (with the possible exception of certain evaporites) do not exhibit significant viscoelastic behavior, at least not over time spans of engineering interest, a plastic analysis is indicated. The analysis is meant to apply to strata whose deformation is dominantly that of bending such as might be expected in the remote roof about a longwall face.

Jan 1, 1970

By C. M. Wayman, J. F. Breedis

The crystallography of the martensitic transformation in the Fe-30 Ni alloy was reinvestigated. The scatter in the habit Plane as determined from measurements on the mid-rib plane was smaller than reported previously, and the orientation relationship was determined from a martensite plate having known direction cosines. From agreement with crystallographic theory and from observations of the morphnlogy of the martensite plates, it is suggested that the mid-rib plane represents the starting region of the transformation. THE crystallography of the martensitic transformation in the iron-nickel system has been the subject of many investigations.&apos;-7 However, for iron alloys containing approximately 30 wt pct Ni, a wide scatter in the reported habit planes exists. In only one instance has a Laue determination of the orientation relationship been made, but the habit plane of the martensite plate studied was not determined experimentally. Because the most successful thermodynamic and kinetic analyses8 of the martensite transformation have been based on Fe-30 Ni alloys, it was considered desirable to reinvestigate the crystallographic features of the transformation in this alloy. Lieberman9 suggested that the most significant information for use in a theoretical treatment involves the determination of all the crystallographic observables from a single plate of the product phase. This was first done in essence by Greninger and Troiano10 for Fe-22 wt pct Ni-0.8 wt pct C, and is the method followed in this investigation. Some theoretical approaches11-13 in describing the martensitic transformation consider the overall transformation distortion to be comprised of a Bain distortion, or lattice deformation (PI, which produces the structure change, and a lattice invariant deformation (G), such as twinning, which together leave the interface or habit plane un-distorted. The incorporation of a rigid body rotation (R) results in a transformation distortion (E) such that the interface plane is left both undistorted and unrotated. In matrix notation, E = RPG where the lattice invariant deformation has "taken place" in the austenite. Bowles and Mackenzie14-16 in formulating a theoretical approach proposed an adjustable scaler quantity, denoted as 6, which represents a uniform dilation in the interface plane. This dilation acts to adjust the lattice spacings of the parent and product structures at the plane of contact. Using the dilation parameter as a variable, these authors were able to account for a continuous variation of habit planes in steels along a curve in the stereogram between {225}A and {259}A. she invariant line strain14 of the transformation is 6 RP, and the corresponding transformation distortion is E/6.) With the dilation parameter known, the invariant line is computed as the triple coincidence of the habit plane, the shear plane of the lattice invariant deformation, and the initial Bain cone.14 The contraction axis for the Bain distortion can be taken9&apos;17 as [010]A, and the correct permutation of the habit plane indices used. Kelly and Nutting 18 have established the shear plane (of twinning) in the tetragonal martensite of Fe-22 Ni-0.8C to be {112)M by means of transmission electron microscopy. The reasonable shear system is then {112}M which is equivalent to {011}A <01l>A. The as-

Jan 1, 1962

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By W. A. Anderson, F. N. Rhines, W. A. Johnson

THE rate of the high-temperature oxidation of pure copper has been measured repeatedly by numerous investigators. It appears to be generally agreed: (I) that at constant temperature, after the initial stages of oxidation have been passed and the scale has attained a substantial depth, the film thickness increases in proportion to the square root of the time of oxidation; and (2) that for any given period of oxidation the logarithm of the square of the film thickness is proportional to the reciprocal of the absolute temperature of oxidation.&apos; These relationships are explained upon the basis that the rate of diffusion of copper to the external surface of the film is the controlling factor in establishing the rate of growth. Extensive studies have been devoted also to the mechanism and rates of the early stages of oxidation. There is thus available a reasonably well established theory of the oxidation of pure copper upon which to construct an explanation of the more complex oxidation of copper alloys. Few general principles have as yet emerged from the chaos of observations that have been reported in the field of the oxidation of alloys.2 It is evident, however, that the copper alloys may be divided into two main groups, whose oxidation characteristics are distinguish able. The first group, composed of the alloys with the noble metals, forms substantially pure copper oxide scales; the alloying element is concentrated within the residual metal, and sometimes particles of almost pure noble metal are found in the scales completely surrounded by copper oxide. In the second group, composed of the alloys of copper with the baser metals, the alloying element appears as an oxide in the scale, often in greater concentration than in the alloy itself and sometimes to the exclusion of copper oxide. The oxide scales of the latter class have been found to be made up of one, two, and sometimes more distinguishable layers of which the innermost is often metallic in character, composed of particles of the oxide of the alloying element embedded in essentially pure copper and known as the subscale or zone of internal oxidation. The need for a thorough quantitative study of these modes of oxidation is evident. Since it is apparent that several mechanisms must be cooperating to produce the complex oxide scales found on copper alloys, the analysis of the process into its several simple operations should prove instructive. Fortunately, it is possible experimentally to produce internal oxidation in the absence of an external scale; this permits the isolation and intensive study of one of the steps in the oxidation process. In the present research the rates of internal oxidation of an extensive series of dilute solid solution alloys of copper have been measured and a theory has been developed to predict the observed

Jan 1, 1941

By A. W. Hull

The new valves described in this article are the latest product of the Research Laboratories of the General Electric Co. Some of them are still in the laboratory stage, others have already found important applications. Some of the larger ones, which have graduated from the laboratory, are waiting for their apprenticeship in industry, there to refine their frailties and complete their preparation as electrical servants. The career that awaits them, though dimly foreseen, appears fascinating. And as surely as history repeats itself, scenes still more romantic, now beyond the horizon, will unfold as we approach them. This is the romance of science. Counting Electrons Let the smallest tube lead the march of review. It is a special Pliotron, designed to measure currents smaller than any yet detected. It goes by the unromantic name of Pliotron FP-54. Fig. 1 shows this miniature tube—miniature in performance rather than size, for it is the size of an ordinary radio receiving tube. Its appearance has nothing distinctive, except the quartz beads above and below the plate, which support the grid. They minimize insulation leakage. In principle, the FP-54 is like any grid-controlled high-vacuum electron tube; but in structure and operating characteristics it is entirely special. An extra "space-charge" grid, maintained at 3 volts positive with respect to the filament, holds back the small but pernicious current of positive ions emitted by the filament; the normal plate voltage is 6 volts, grid bias 3 volts, thoriated-tungsten filament temperature 1700" K., plate current 40 microamperes. These conditions are essential to the avoidance of grid-currents, which may consist not only of insulation leakage and positive ions from the hot filament and from residual gases, but of high-speed electrons from the filament, photo emission from the grid due to the light of the filament, and electron emission caused by X-rays generated by the impact of electrons on the plate.

Jan 1, 1932

By T. E. Leontis, D. H. Feisel

MAGNESIUM alloys containing rare earth metals have received considerable attention during the past several years because of the need for light alloys having high strength and creep resistance at elevated temperatures. Although much of the work reported earlier has dealt with alloys containing Mischmetal, it has been shown in two previous papersl, V hat distinctly different effects are produced by various rare earth metals and rare earth metal mixtures on the properties of magnesium. For example, much higher strengths are obtained in magnesium alloys containing didym-ium (essentially neodymium plus praseodymium) than in alloys made with Mischmetal, which contains all the rare earth metals in the proportions in which they occur naturally in the monazite ore. Mg-rare earth metal alloys are characterized by a relatively coarse grain size, which greatly impairs castability. The addition of zirconium as a second alloying ingredient has been shown8,7 to refine the grain size, which also produces a distinct improvement in the strength properties. Certain Mg-Mischmetal-Zr and Mg-Mischmetal-Zn-Zr alloy compositions which are currently being produced commercially have been discussed in dytail by Nelson and Strieter,8,4 who also present some in- formation on a Mg-low Ce-Mischmetal-Zr alloy, and by Nelson.8 A patent issued to Jessup, Emley, and Fisher9 emphasizes the superiority of Mg-didymium-Zn-Zr alloys over the corresponding alloys made with Mischmetal. The purpose of this paper is to present the results of an extensive investigation concerned with the effect of increasing amounts of zirconium on magnesium sand casting alloys containing several different rare earth metal mixtures in varying amounts. The effect of the addition of zinc to some of these alloys is also being reported. Preparation and Testing of Alloys The alloys studied in this investigation were prepared in small laboratory melts according to the melting procedures described by Nelson1" as the Crucible Method. Electrolytic magnesium having the composition shown in Table I was used as the starting material. The rare earth metal alloying ingredients used in preparing these alloys were essentially of the compositions listed in Table 11. Some of the didymium-containing alloys were prepared using a Mg-didymium hardener. The rare earth metal content of this hardener analyzed 1.2 pct Ce, 10.4 pct Pr, 80.8 pct Nd, and 7.6 pct La. The zirconium was added in one of three forms: 1) as sponge zirconium obtained from the Bureau of Mines; 2) as a fused salt consisting of 50 pct ZrCl, and 50 pct alkali chlorides from which the zirconium is reduced by the magnesium; or 3) as a Mg-Zr hardener. The alloying procedures and melt hand-

Jan 1, 1958

By William A. Johnson

IT was pointed out in an earlier paper1 that our understanding of the atomic mechanism by which diffusion occurs in metallic alloys is scarcely in an advanced state. This unsatisfactory condition is the result not of any lack of interest, but of the difficulty of designing experiments that will yield suitable data. The diffusion coefficient of an alloy, measured in the usual way, is simply a number specifying the rate of homogenization of a nonhomogeneous metal; this number, of itself, can furnish neither the rate at which the individual atoms move nor information as to the mechanism by which they move. It does not necessarily follow, however, that such information cannot he obtained, even if the path to be followed is still not clear. Much success has been attained in the study of diffusion in ionic crystals. A number of experiments, for which there are few counterparts in connection with metals, yields information often indicating a detailed mechanism by which diffusion probably occurs. From such work, quite acceptable theories of lattice imperfections have been developed by Wagner, Schottky, Frenkel, Jost and others.2 It is postulated that real crystals of stoichiometric composition contain, in equilibrium, certain imperfections of which the most important types are: (I) vacant cation sites, with an equal number of interstitial ions; (2) vacant anion sites, with an equal number of interstitial ions; (3) equal numbers of anions and cations in interstitial positions; (4) equal numbers of vacant anion and cation sites. The classification of a particular crystal according to this scheme then follows from studies of the variation of electrical conductivity with pressure of the electronegative component surrounding the crystal, with ion size, and with temperature; other physical phenomena, such as the Hall effect, have aided in establishing the classification. The relative mobility of the anion and cation may be determined by chemical analysis of the salt at the electrodes following electrolysis. With such information, and knowing that one ion never occupies the lattice site normally belonging to an ion of opposite sign, it is usually possible to ascertain the diffusion mechanism. It is clear that the same experiments are not applicable to metal crystals, and substitute experiments that yield as much information have not yet been devised. Much can be learned, however, about the mobilities of the two* kinds of atoms in alloys by the use of radioactive metals as indicators. Only one such experiment has been performed in the past. In 1933, Seith and Keil,3 in an effort to explain the great difference between the rate of diffusion of gold in lead and of lead in lead, measured the rate of diffusion of radioactive lead in a gold-lead

Jan 1, 1942

By Clarence Zener

The heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an understanding will involve two distinct types of inquiry: (I) the direction of the transformation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed herein—steel—such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron-alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data &apos;being obtained from the simple binary and ternary equilibrium diagrams. Fundamental Equations In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body-centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may. be regarded as filling all the lattice positions of a given type. The introduction of the fundamental the of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1947

By Clarence Zener

The heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an understanding will involve two distinct types of inquiry: (I) the direction of the transformation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed herein—steel—such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron-alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data &apos;being obtained from the simple binary and ternary equilibrium diagrams. Fundamental Equations In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body-centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may. be regarded as filling all the lattice positions of a given type. The introduction of the fundamental the of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1947

By J. Charles Miller

THE expansion of facilities for rapid transportation of perishables by train, truck and airplane has necessitated consideration of refrigerants of a minimum weight and volume per pound of cooling and has stimulated the use of solid carbon dioxide commercially. The gas probably has not had wide application in the past in air-cooling equipment for mines, theaters or buildings, owing to its thermodynamic properties, as will be deduced from examination of Table 2. However, consumption of the liquid in carbonating beverages remains a dominant factor. In addition to these uses, carbon dioxide is employed to a limited degree as an explo-sive in the liquid form, as a freezing agent in plumbing, in laboratories for low-temperature work, and in the manufacture of golf balls.

Jan 1, 1936

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.&apos;s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

By Kenneth L. Cook

GEOPHYSICAL exploration is continuing to expand in scope and variety of methods, in experimental studies of specific applications, and in development of theory for complex situations. Aerial surveys have been made economically more attractive by simultaneous recording of magnetic and radioactivity data, and aerial electromagnetic surveys have been attempted. The most significant success of mining geophysics was the discovery of huge lead-zinc-copper sulphide ore deposits in New Brunswick, Canada. Spectacular geophysical astivity has occurred in the area as a result of these discoveries, and geophysics is expected to continue to play a large role in this drift-covered area. Other developments this year find the Atomic Energy Commission making available monthly reports of the location of anomalous radioactivity detected in aerial and ground surveys and the AEC is installing supersensitive radioactivity assaying instruments in about 25 localities in the U. S. Interest in helicopters is being aroused because of potentialities for near-ground surveys and better location control of anomalies. Japan can be added to the list of countries using geophysical surveys extensively.

Jan 2, 1954

By John H. Bassarear, A. A. Dor

INTRODUCTION Primary grinding mills as defined in this paper, are autogenous or semi-autogenous rotating, tumbling mills having a coarse feed with a top size usually varying from 150 to 300 mm (6 to 12 inches). Most frequently, the feed to these mills is the product of primary crushing plants but in some cases run of mine ore is used as feed such as at Benguet, McDermitt, L-Bar Sohio, Bear Creek and others. The size of the largest lumps in the mill feed is principally determined by limits set by the mill feed trunnion diameter and by the type and size of conveying equipment used for handling and of bins and stockpiles used for storage. The use of primary mills in mineral processing plants has expanded very significantly in the last twenty years, and they have been successfully applied to the treatment of a wide variety of ores in both wet and dry grinding applications. In the present state of technological development for primary grinding mills, there is a wide choice of acceptable options with respect to type and size, grinding flowsheet and grinding media. The choice of the optimum combination which would result in the most satisfactory condition of operation, from the standpoint of both metallurgical results and costs, depends on the nature of the ore, the required characteristics of the grinding products and on various geographic and economic circumstances. The effects of such factors and considerations on the choice and sizing of primary grinding mills and flowsheets are reviewed and discussed in the following pages. PRIMARY MILLS SELECTION Inherent Characteristics of Primary Grinding Primary grinding is complex because it involves several comminution mechanisms which occur simultaneously and to some degree interfere with one another. These mechanisms of impact, attrition and abrasion have been described earlier. The relative importance of these three main grinding actions and their mutual balance resulting in a continuous uniform operation of the mill depend to a very large extent on the nature of the ore and its physical properties. Homogenous, single mineral ores will behave quite differently from heterogenous ores consisting of different minerals bound together along defined

Jan 1, 1982

By Arthur Notman

YEAR ago, the Committee on Mineral Economics ventured to predict a more realistic attitude by the public toward the folly of seeking to have more by making less under the guidance of the Blue Eagle. A unanimous decision of the Supreme Court of the United States has now laid that embattled bird to rest. De rnortuis nil nisi bonum. In spite of dire predictions of disaster to follow its early demise, the metal industries and many others have improved substantially. One could name many indications of that improvement, and on the strength of stock-market activities might assume

Jan 1, 1936

By Glen R. Neighbors, Sylvan Cromer

HIGH subsurface temperatures and pressures are making cementing operations more difficult as deeper producing horizons are being sought. Recorded bottom-hole temperatures above 200°F. and pressures in excess of 12,000 Ib. per sq. in., obtained by combining hydrostatic and pump pressures, are not uncommon. Insufficient time is available for proper placement of standard Portland cement, because of the shortened setting time produced by these excessive temperatures and pressures, therefore special types of cements have been developed to overcome these difficulties. From the standpoint of placement, the ideal slurry would be one that would remain fluid long enough to be placed, then harden rapidly, so that there would be a limited amount of contamination and the well could be placed on production in a minimum of time. It is highly desirable, therefore, that some method be devised to measure accurately the time that any slurry will remain in a fluid state while being pumped into the well. To study the effect of elevated temperature and pressure on fluidity, the authors have developed the pressure-type consistometer (Figs. I and 2) described below, and are presenting data obtained with it, using slurries of both quick-setting and slow-setting cements. Studies were made over a temperature range from 110° to 270°F., and a pressure range from atmospheric to 3000 lb. per sq. inch. APPARATUS The fluidity of cement slurries at atmospheric pressure is usually determined with the Halliburton consistometer1 or the Thickening Time Tester.2 These instruments are similar, in many respects, to an ordinary ice-cream freezer. The slurry to be tested is placed in a container that is rotated at a constant speed with an electric motor. Constant temperature is maintained by surrounding the container with a thermostatically controlled bath. The torque on the paddles, which is proportional to the force needed to shear the slurry, is indicated on a scale. The Halliburton instrument is calibrated from 0 to 100 poises against fluids of known viscosity. To permit direct correlation of observed elevated pressure data with those published at atmospheric pressure, the authors&apos; designs of the slurry container, paddle, and torque indicator closely resemble those used on the Halliburton instrument. Duplicate results may be obtained at atmospheric pressure in either instrument. Instead of the atmospheric constant-temperature bath, one was built from a high-pressure steel bull plug. A Uni-Bolt union equipped with a blanking plug serves as the top, permiting the instrument to be opened or closed in less than one minute. The slurry container is built from Shelby steel tubing. A wrench socket welded to the bottom of the container engages a hexagonal nut on the top of the steel shaft that rotates it. This acts as a universal

Jan 1, 1941

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorinationt of olivine has two major defects: (I) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatments and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By Richard D. Hagni

Abstract-Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in mill Products. The mill dressing engineer should be more aware of the types of beneficiation problems that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations of the mineral constituents of an ore or mil1 product can be visually determined. This advantage provides solutions to many beneficiation problems. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in floculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 10, 1978