Search Documents

By F. M. Lewis, J. E. Goodman

A larger, slow-speed, under-loaded ball mill and hydraulic classifier have almost doubled grinding efficiency at the lsabella mill. TENNESSEE Copper Co. operates two ore con-A centrators, the London and Isabella mills near Copperhill, Tenn. In 1948 and 1949 the small ball mills and rake classifiers in the London concentrator were replaced by one large ball mill and one hydraulic classifier. This new ball mill was designed oversize so that it could be operated at slower than normal speed. The proper operating conditions were established and the results published.' Later it was found that this mill operated more efficiently with a small ball charge." While this London grinding practice was being developed, the Isabella grinding circuit was not changed in any way. It remained a conventional two-stage rod mill—ball mill combination, the rod mill in open circuit and the ball mill in closed circuit with a rake classifier. Study of the data indicated that grinding cost could be lowered by converting to the London practice, but not enough would have been saved to warrant the expense of converting. No plan for improving this grinding operation could be developed. In 1953 this study was reopened when plans were made to increase the Isabella mill output from 1150 to 1500 tpd. At this time the grinding circuit consisted of a 6x12 rod mill followed by a 6x12 ball mill in closed circuit with a 6-ft rake classifier. Another 6x12 ball mill and 6-ft rake classifier would have been sufficient equipment and would have been the simplest and cheapest installation. However, this would have offered no improvement in grinding efficiency or operating cost. If, on the other hand, the grinding operation could be converted to the London practice, by installation of one large 101/2x9x9 tricone mill and a 10-ft hydroscillator,2 lower operating costs would justify the additional investment. Economics: Table I presents estimates for the two schemes for enlarging the Isabella mill. In the first scheme, column 1, one 6x12 ball mill and one 6-ft rake classifier were to be added. In the second scheme, column 2, the existing small ball mill and rake classifier were to be retired and one large mill and hydroscillator were to be installed. Estimated savings from the difference in operating costs made an attractive return on the additional investment for the large mill and hydroscillator. Actual costs of carrying out this plan are tabulated in column 3b. It will be seen that these costs follow the estimates in column 3a very Closely. The return on the additional investment is calculated from the difference in the operating cost in column 1 and the actual operating cost in column 3b. This too come very close to the estimate. Power and Steel: Power requirements and steel consumption for the rod mills and ball mills, both actual and estimated, are presented in Table 11.

Jan 1, 1958

By Donald H. McLaughlin

MINERAL industry activities have not been seriously hampered by a lack of men with higher training. The balance between opportunities for employment and advancement and available personnel has been a happy one, with enough competition to stimulate effort but not the unfortunate conditions arising from an overabundance. of employment seekers. Nearly all mineral industry educational institutions have been concerned about the falling enrollment in mining and metallurgical courses of study during the past decade. But industry has drawn upon a supply of many types of technically trained men apart from those who prepared their careers specifically in the mineral industry. Some schools have made this possible by uniting geologists, mineralogists, and others with students in mining and engineering. On the other hand, some schools have combined their department of mining engineering with an over-all engineering department and continue to send their graduates into the mineral industry by another route. On the whole, this seems to be a good trend and is likely to result in men better trained for current problems than would have been possible under the older rigid curricula.

Jan 1, 1947

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

US 4,135,913-Extraction of nickel values from iron-containing nickel sulfide ore, particularly pentlandite or nickeliferous pyrrhotite A mixture of raw ore, roasted ore, or iron powder, and coal as a reductant is heated to a temperature of 800- 1000° C in a nonoxidizing atmosphere to convert the bulk of the iron content to metallic iron while diffusing into the iron the bulk of the nickel, the mixture cooled, and the cool material separated into a magnetic fraction containing most of the nickel and a non-magnetic gangue fraction A Illis arid L S Renzoni, assigned to International Nickel Co, Inc Jan 23, 1979 7 pp (75-21) Filed 10-10-75 (621,343) Priority Canada, 10-27-72 (155,032) Same Canadian 981,910, dated Jan 20, 1976 Same British 1,389,145, dated Apr 3, 1975 US 4,135,917-In the recovery of gallium from a solution obtained by the digestion of bauxite or nepheline in an alkali solution for the production of alumina, the digestion solution is neutralized, the neutralized solution evaporated to an op¬timum caustic alkali concentration and adjusted to a ratio of alkali metal oxide to alumina of above 2, the corrected solu¬tion contacted with a gallium-aluminum alloy, arid high-purity gallium recovered from the solution by electrolysis or cemen¬tation K A Badaliants, et al Jan 23, 1979 6 pp (75-109) Filed 12-19-77 (862,201) Priority USSR, 12-22-76 (2,428,¬006) US 4,135,918-Extraction of copper from copper sulfide ore containing also one or more of the metals iron, nickel, arid cobalt Ore is roasted at a temperature of 750-800° C to expel sulfur, the sulfur-free calcine slurried in water containing a sufficient amount of sulfuric acid to supplement any sulfuric acid formed in situ, the slurry heated at 150-165° C in the presence of a reducing gas to form soluble sulfates of metals other than copper while reducing copper to elemental form, arid the slurry filtered to recover copper solids Any precious metals present in the ore will report with the copper solids V A Ettel, A P Devuyst, R Sridhar, arid C. E O'Neill, as¬signed to International Nickel Co, Inc Jan 23, 1979 5 pp (75-117) Filed 3-2-78 (882,610) Priority Canada, 5-13-77 (278,360)

Jan 1, 1980

By T. K. Perkins, R. N. Hoffman, O. C. Johnston

A simplified theory of viscous fingering in miscible systems has been developed. It predicts the correct functional relationship between pertinent variables and permits the calculation of the order of magnitude of fingering behavior for simple systems, such as linear or radial. The theory is based on the following four observations: (1) cross-flow takes place only near the ends of fingers; (2) the relative finger width is about 0.5; (3) fingers can be suppressed by transverse dispersion, the suppression being quantitatively described by a critical ratio of dispersion times; and (4) the widths of extending fingers are close to the minimum size finger that can grow at any stage of displacement. Fingering is studied in two-dimensional linear and diverging radial systems, both theoretically and experimentally. For linear systems, the length of the fingered region is proportional to mean displacement; the finger width is proportional to square root of mean displacement; and there is a small initial region void of fingers because of suppression by longitudinal dispersion. For the radial system, two limiting conditions are recognized. If the mean displacement is small compared with the wellbore radius, the length of the fingered region is proportional to the mean displacement. The width is proportional to the square root of mean displacement. If the mean displacement is large compared with wellbore radius, length of the fingered region is proportional to mean displacement, but the number of fingers approaches a constant value. Also, in the radial case there is a small initial region void of fingers because of longitudinal dispersion. INTRODUCTION The behavior of viscous fingers in miscible systems has been of interest to the oil industry for many years. Previous studies have clearly shown the existence and nature of fingers in small models.1,2,3,4 Engineering techniques for extrapolating to reservoir situations have been proposed. 5,6 Still, because of the lack of a real understanding of the mechanics of fingering, there remains uncertainty and disagreement as to the best way to scale or calculate fingering behavior in the reservoir. In this paper we discuss a study of the mechanics of fingering in miscible systems (i.e., why do fingers behave as they do?). A simplified theory is developed which we believe will (1) predict the correct functional relationship between pertinent variables, (2) permit us to calculate the order of magnitude of fingering behavior for simple systems such as linear and radial, and (3) give further insight into the problem of scaling or otherwise extending the results to more complicated reservoir conditions. The paper includes the following sections: (1) brief summary of the mixing behavior of miscible fluids in linear and radial systems; (2) four fundamental observations of fluid flow (under fingering conditions); (3) based on these four observations, a simplified theory of fingering in linear and radial systems is developed; and (4) the theoretical equations are compared with experimental fingering data measured in laboratory models. A REVIEW OF DIFFUSION AND DISPERSION As will be shown later, the behavior of viscous fingers in miscible systems is controlled in large degree by the mixing between the two fluids. A quantitative description of fingers will first require a quantitative description of mixing. Fortunately, much work has been done to clarify this subject; a fairly comprehensive review has been presented in a previous paper. 7 For present purposes let us (1) briefly summarize the quantitative description of diffusion and dispersion (both longitudinal and transverse) within a differential element; (2) present a simplification of the "width of mixed zone"; and (3) describe the effect of geometry on width of mixed zone. If one fluid is displaced from a porous medium by another miscible fluid (in the absence of fingers)

Jan 1, 1966

By G. Bassi

RECENTLY Wallbaum¹ found that copper wires with different degrees of deformation up to 98.7 pct area reduction recrystallize giving a [112] texture, while deformation over 98.7 pct gives either a [l00] texture at low temperatures or a [1ll] texture at high temperatures. Furthermore it was found that the recrystallization temperature as a function of deformation up to 98.7 pct decreases as expected, but increases over that deformation. Wallbaum concluded that the different textures have different recrystallization temperatures. The [112] texture has the lowest and [Ill] the highest. At the same time Bassi² found that for high deformation (over 99 pct area reduction) and for an annealing temperature of 400°C, the [l00] texture first forms and with prolonged annealing time the [12] texture appears through grain growth. This secondary texture does not appear if the wire is annealed at 1000°C before the deformation. From these two papers it might be concluded that the [I12] texture can appear either as a primary or as a secondary texture after annealing. The texture formed in a special case depends on the previous history of the wire. Probably the texture of the wire prior to the last deformation is important. To investigate this, wires were produced by adequate deformation and annealing to give a [l00], a [112], and a [lll] texture. The wires then were given a series of different deformations and were annealed at various temperatures, after which the textures were studied. Experimental Work The copper used was electrolytic tough-pitch (Cu 99.90 pct and 0, 0.04 pct). Three wires with the different initial textures were made in the following way: The [l00] and [112] by drawing a 16 mm rod to 1 mm and annealing it 16 hr at 200°C and 2 hr

Jan 1, 1953

By J. M. Morkowitr

A. Sawatzky (Atomic Energy of Canada, Ltd.)—The detailed criticism by Markowitz of my simple treatment of the thermal diffusion of hydrogen in Zircaloy-2 indicates that my paper was not as lucidly written as it could have been. I would therefore like to reiterate several of the main points of my proposed mechanism and describe in more detail some of the features only implied in the original paper. The distribution equation derived in my paper was stated to hold only for the case where the volume taken up by the hydride was small compared to the volume taken up by the solid solution phase, subsequent work, mentioned below, having shown it to be out by only a few percent up to a hydrogen concentration of about 3000 ppm. Of course, hydrogen in the two-phase region alone is not conserved in my treatment as pointed out by Markowitz. On the contrary, one of the important features of my proposed mechanism is that in the presence of a temperature gradient a two-phase region cannot exist over the whole specimen. For example, if the specimen is entirely a + 6 initially, then on application of a temperature gradient, a single phase (a) region at the hot surface develops from time t = 0 onwards. As mentioned in my original paper, the interface between the a and a+d regions moves toward the colder surface of the specimen with a discontinuity in hydrogen concen- tration developing at the interface and increasing with time. This interface moves at such a rate that hydrogen in the specimen as a whole is conserved. It must be pointed out that my distribution equation (Eq. [5] in Markowitz's paper) holds only for linear geometry. It is easy to show that for the cylindrical geometry of Markowitz the assumptions used in my treatment lead to

Jan 1, 1962

By J. R. Linney

THE Eastern magnetite industry has not failed in its contribution to the war program during the past year. Man-power shortage was the critical problem in maintaining production and for the last half of the year, owing to lack of man power, it was necessary for some mines to change from seven to six days per week schedule. At Cornwall, Pa., the mine operated by the Bethlehem Steel Co. produced approximately 2,000,000 tons of crude ore and 1,200,000 tons of iron ore concentrates, a decrease of about 10 per-cent compared with the previous year. Railroad haulage in the open-pit at this mine was discontinued, being replaced by Mack trucks of approximately 30 tons' capacity. At the Mt. Hope mine in New Jersey, the Warren Foundry and Pipe Corp. produced about 195,000 long tons of crude ore obtaining 70.000 long tons of lump ore and 35,800 long tons of concentrates. An additional 24,500 long tons of concentrates was produced from a stock pile of 47.000 long tons of crude ore accumulated during the latter half of 1943, following the fire in their old dry mill. All of this material was handled through their Brown

Jan 1, 1945

By Gilbert L. Eggert

The effects of reactor irradiation on age hardening in a Cu-2 wt pct Be alloy have been investigated in two neutron-energy ranges. During some of the irradiations, specimens were exposed to high-energy fission neutrons which passed through a boron-10 shield; during other bombardments, the boron-10 was omitted and specimens were irradiated in a reactor thermal column, or the fuel configuration was modified to increase the thermal-neutron flux at a location in the core. Differences in length, X-ray diffraction angle, and hardness indicated that low-energy neutron irradiation made a small contribution to changes in the measured properties. The influence of defects generated by knock-om with less than the Brinkman critical energy or by prompt (n,y) recoil is suggested as the cause of this effect. EXPERIMENTS designed to test the effects of reactor irradiation on the properties of age-hardening alloys have to the present time employed fluxes un-differentiated according to neutron energy. Billing-ton and Siegell in 1950 were the first to perform such an experiment and to compare the results with those obtained by thermal aging. These authors concluded that precipitation in a Cu-2 wt pct Be alloy was not enhanced by the radiation. However, 4 years later, Murray and Taylor,2 working with specimens of the same Cu-2 wt pct Be alloy, reported that an increase in density, hardness, and resistivity which followed reactor irradiation resembled changes associated with thermal aging at about 100°C. (It should be noted that these authors reported that higher aging temperatures caused a decrease in resistivity.) cupp3 reported hardness results similar to those of Murray and Taylor. Koppenaal4 showed that irradiation-enhanced precipitation and irradiation defect hardening were not simply additive but that they acted separately in an irradiated alloy. Kernohan et a1.,5 working with Ni-Be, offered evidence that beryllium was removed from solid solution by reactor irradiation and suggested that the mechanism was one of increased diffusion through the use of vacancies in the structure. piercy6 also found that more precipitate particles were formed by fission-neutron irradiation of a Cu-Co alloy which contained a small amount of particles before irradiation. He proposed that the additional particles were caused by an appreciable amount of diffusion during the final cooling of displacement spikes. The retrogression of extant precipitate particles found by Murray and Taylor2 and Boltax7 as well as piercy6 indicated that nuclei were dissolved within a high-energy spike region and, upon resolidification of the perturbed volume, new nuclei precipitate and grow by enhanced diffusion. Bleiberg et al.' and Konobeevski et al.' explained phase changes obtained by irradiating fissionable alloys in terms of retrogression and re-precipitation in regions of high-energy spikes. Parsons and Balluffi10 used electron microscopy to verify that crystallization did indeed occur in displacement spikes which were formed in amorphous germanium by fast-neutron irradiation. The concept that low-energy neutron irradiation might cause structure-sensitive property changes in semiconductors by atomic recoil associated with the (n, y) reaction was first proposed by Schweinler" and walker." This thesis was tested by Cleland and crawford" and found to be valid. Coltman et al.14 exposed a variety of pure metals to thermal-neutron irradiation at cryogenic temperatures and attributed the resulting resistivity changes to the action of defects created by (n, y) recoil. The present work was undertaken to extend the concepts of Schweinler," walker," and Coltman et al.I4 to the case of an age-hardening alloy and to determine whether or not the action of defects produced by thermal-neutron irradiation would en-hance age hardening. EXPERIMENTAL PROCEDURE Omeea West Reactor Irradiations.* Thermal-

Jan 1, 1965

By Walter R. Hibbard

BACKOFEN' reported recently that "the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [lll.] and [loo] directions aligned parallel to the wire axis." In the introduction, he indicated that this was in contrast to the work of Hibbard,' who reported a single [111] texture after a reduction of 96.4 pct. Unfortunately Backofen stated that this was a reduction in area when actually it was a reduction in diameter, as is clearly stated in the reference. Moreover, the results of Backofen are in complete agreement with the results of Hibbard. Backofen's 97.3 pct reduction in area is an 83.3 pct reduction in diameter, after which he foundadouble [ll11 and[l001texture with the former predominating. Similarly, Hibbard; after an 86 pct reduction in diameter found a double [Ill] and [I001 texture with the former predom- inating. Hibbard, however, when he drew the wire further to 96.4 pct reduction in diameter, found primarily a single [Ill1 texture as illustrated by Fig. 2 of ref. 3. Here also, Hibbard- reported evidences of the [loo] recrystallization texture found by Backofen. It might also be pointed out that Backofen not only drew his wire 97.3 pct reduction in area but also etched them over 99 pct reduction in area from 0.125 to 0.01 in. diam. Hibbard's wires were drawn directly to size. In summary, the deformation texture of cold-drawn copper wire still may be described as primarily a single Clll] texture after a sufficient amount of drawing, such as 96.4 pct reduction in diameter." a

Jan 1, 1952

By R. E. Cook

This paper presents results of a study to determine to what extent errors in estimated free gas saturation affect the results of static pressure calculations from build-up curves in two-phase systems. Use is made of the method of pressure build-up curve analysis developed by Miller, Dyes and Hutchinson1 , with modifications for two-phase flow advanced by Perrine2. Cornhined fluid compressibility of gas-oil mixtures is included, with special attention given to the discontinuity that occurs in fluid compressibility at the saturation pressure and its effect on static pressure calculations from build-up curves. The sensitivity of static pressure calculations to errors in gas saturation is considered over wide ranges of formation and fluid properties and reservoir pressure conditions. It is concluded from this study that for analyses of two-phase pressure build-up curves (I) the use of under-saturated crude compressibility data, even when producing GOR's are at or near solution values, will result in very significant negative errors in calculated static pressrrre, and (2) except for large values of buildup curve .slope and/or very low crude gravities, rather large errors in calculated gas saturation can he tolerated without .significant effect on calculated static pressures. The conc1usions arc qualified as referring only to the effects of gas saturation and excludc possible errors in the nuumerous other factors that enter into the ancllysis of pressure build-up curves. INTRODUCTION As part of the analysis of basic data for several major Eocene reservoirs in the Bolivar Coastal field (Western Venezuela), it was necessary to analyze a large number of pressure build-up curves for oil permeability and static reservoir pressure. From performance data it became apparent that gravity segregation is very active in these reservoirs. As a result of this performance it was recognized that the free gas saturation within the oil leg of the reservoirs would be small but would be subject to certain errors in calculation due to the inaccuracy of relative permeability data in the low gas saturation region. Since all of the various methods of build-up curve analysis were originally derived for sin- gle-phase, constant compressibility systems, and since the presence of a small but rather indeterminate gas saturation would greatly affect the reservoir fluid compressibility, a study was undertaken to investigate the effect of gas saturation on the results of two-phase pressure build-up analyses. TWO-PHASE BUILD-UP CURVE ANALYSIS The method of analysis used in this investigation is basically that originally developed by Miller, Dyes and Hutchinson1, with modifications for two-phase flow advanced by Perrine2. Miller, et al, showed that the original equation for single-phase permeability away from the well bore, held for two-phase flow except that the calculated permeability is the effective permeability to oil away from the wellbore. This finding was acknowledged by Per-rine, who also presented the equation for effective gas permeability* as Since Eqs. 1 and 2 contain no terms influenced by fluid compressibility, no distinct problem should develop in calculating permeability from two-phase build-up curves. In regard to the calculation of static reservoir pressure from build-up curves in single-phase systems, the modified Miller, et al, method as presented by Perrine is briefly as follows. 1. From build-up curve data, PVT data for the reservoir fluid and the well spacing and sand thickness, calculate the climensionless shut-in time corresponding to the highest value of actual shut-in time (t, hrs) on the straight-line portion of a semi-log build-up curve. Dimenrsionless shut-in time is related to actual shut-in time by the relation, t- 0.000264 kt 2. From a graph of dimension less shut-in time vs dimensionless pressure difference (Fig. 1 1 ) find the value of dimensionless pressure difference corresponding to the value of 7 calculated under (1) above. Dimen-

Jan 1, 1970

By Eric Jette

IN a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "Wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be con-sidered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe304 instead of the original Fe404. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously deter-mined fact that the FeO lattice is ionic (i. e., consists of Fe++ and 0= ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1.

Jan 1, 1933

By G. T. Pruitt, T. L. Irby, P. B. Crawford, H. Ferrell

In water flooding peripheral, center-to-edge, line-drive or water-encroachment patterns the question has arisen, "when should a producing well be converted to a water-injection well?". It is realized that, if the producing well is shut in when water breakthrough occurs, some oil could be left in an unswept area. Yet, operation to high water-oil ratios may require processing much additional water. If a well is shut in, "where should the allowable be transferred?". A review of the literature indicates that very few data are available to the engineer to assist him in answering these questions. It is the purpose of this paper to present information which may be of value in selecting the flooding technique and the injection and producing wells and in scheduling injection and production rates. Certain phases of these problems can be studied in the laboratory. The Potentiometric model is well suited for studying many waterflooding problems. This model assumes that steady-state flow exists, that the mobility ratio is equal to one and that gravitational effects are neglected.'-' The three-phase sand model also has been recognized as an effective means for studying certain reservoir problems. Both models were used in making the study reported here. This paper discusses seven cases utilizing various waterflooding techniques. Data for the first five cases were obtained on the potentiometric model. Data for Cases VI and VII were obtained by constructing and flooding an unconsolidated sand pack (a three-fluid-phase system) and by determining the swept area and cumulative oil recovery for various types of operations. APPARATUS AND PROCEDURE The potentiometric model reservoir was 30 in. long X 10 in. wide by about 1/2 in. deep. Four wells were equally spaced in a line array along the lateral center line. (See Fig. 1.) Well No. 1 initially was an injection well for each of the patterns reported. The cases studied with the potentiometric model and sand model are described herein. The laboratory sand model reservoir was a 30- 10-in. rectangular Lucite vessel packed with sand to a depth of about 0.65 in. Four wells were equally spaced in a line array along the lateral center line. The reservoir material was an unconsolidated sand into which the reservoir fluids were mixed to yield fluid saturations of 55 per cent oil, 25 per cent water and 20 per cent gas. The water was added to the sand and the material mixed, after which the oil was added. Kerosene and water, the fluids used, gave a viscosity ratio of 1.64:1. In packing the reservoir, care was taken to assure constant fluid saturations and constant porosities. A new mixture was prepared for each run. During water flooding, a colored water was injected by a constant rate pump. The injection rate was 1.1 B/D/ft of sand thickness. For this series of tests, each of the producing wells was open to the atmosphere and, as in the potentiometric model study, Well No. 1 initially was an injection well for each of the patterns. KESULTS OF POTENTIOMETKIC MODEL STUDlES Two cases (Cases I and 11) involving equal pressure injections were studied, with the following results. Case Water injection was initiated at Well No. 1; the producing wells (Nos. 2, 3 and 4) were operated at constant and equal bottom-hole pressures. When water broke through at Well No. 2 and achieved the selected water-oil ratio, Well 2 was converted to a water injection well, resulting in two injection and two producing wells. The injection pressures at Wells 1 and 2 were maintained equal and constant; pressures at the producing wells were held equal, but they were lower than those at the injecting wells. A similar process was repeated when water broke through at Well No. 3. The flood was terminated when

By R. W. Mancantelli, J. R. Woodward

IN 1947 a large low grade deposit of uranium was located in the northwest corner of Saskatchewan, in the Beaverlodge property of Eldorado Mining & Refining Ltd. Most of the values occur as thin seams and as coatings on other minerals, and the ore, which is light and friable, is not amenable to the usual gravity methods of concentration. The acid leaching process developed to retreat the company's Port Radium tailings was also impractical, as the percentage of carbonates is high and the percentage of sulphides relatively low. Construction of the mill building and installation of equipment, both scheduled for 1952, awaited selection of a satisfactory ore dressing process on or before Oct. 1, 1951. An extensive research program on dressing of ores from the Ace mine therefore was undertaken by the Mines Branch in Ottawa, a research team at the University of British Columbia, and an ore dressing group at the company's Port Hope refinery. Pilot plant operations were conducted at the Ottawa plant of Sherritt Gordon Mines Ltd. under the general direction of C. S. Parsons, consultant on metallurgy and ore dressing for Eldorado. In mid-September, having compared results of the several research programs, Dr. Parsons recommended a process employing a carbonate or basic leach. He reported that, while the chemistry of the process had been proved, engineering of the flowsheet was incomplete, and he suggested that under normal conditions further pilot plant work at the Ace mine might be profitable. However, since this would involve a delay of 12 to 18 months in bringing the property into operation, he recommended that design of the concentrator proceed immediately. Concentrator capacity was determined by two considerations: 1) the amount of ore then available and 2) the expectation that continued improvements would be made in the ore dressing process as a result of the intensive research being carried out by the Mines Branch of the Department of Mines and Technical Surveys. As these improvements could affect both the chemistry and the en-

Jan 1, 1956

By R. W. Kraft

A comprehensive analysis of the crystallographic and metallographic structure of several Al-CuAl, lamellar eutectic grains solidified under equilibrium conditions has been performed. A consistent pattern was discovered which was interpreted in terms of a detailed atomistic model of an interface describable as: Interface II {111} AL 11 {211} <101>Al <120> ? Several arguments are presented to substantiate the theory. It is compared in detail with another interface model characteristic of the Wid-manstatten precipitate of CuAl2 in A1 at low Cu levels. In addition, a concept is proposed to help explain the structure of the compound CuAl2. It has been shown that the eutectic alloy between A1 and CuA1, can be forced to solidify as substantially parallel lamellae throughout a relatively large volume&apos; by appropriately controlling the solidification parameters of growth rate, thermal gradients, and impurity level and by causing solidification to proceed in a unidirectional fashion from one end of an ingot to the other. A typical ingot solidified in this manner shows three distinct zones along the length of the ingot, Fig. 1. At the head end is a region consisting of many different grains, some of which are elongated slightly in the direction of solidification. After a few centimeters of growth, this polygrained region gradually merges into the second zone which consists of a very few elongated coarse grains. The third zone at the tail end is a region of eutectic colonies caused by segregation of impurities. Microscopic examination of transverse and longitudinal sections of the ingots reveals that during the initial stages of growth (zone I) the lamellar structure is frequently highly distorted and twisted but that it straightens out in zone 11. This characteristic pattern suggests that nucleation of a eutectic grain begins randomly at the head end of the ingot, and that some particular orientation relationship between the phases is more favorable from an energy consideration than others for one reason or another, so that some grains grow and others which are less favorably oriented do not. The favorably oriented or "low energy" grains continue to grow until excess solute rejected at the advancing liquid-solid interface destroys the parallel lamellar structure by forming a cellular rather than a substantially planar interface. When this occurs, the parallel lamellae fan out and eutectic colonies are formed because the lamellae grow perpendicular to the local interface. Questions naturally arise as to the crystallographic nature of the "low energy" grains. What do the grains which persist into zone II have in common? Can this explain the stability of such grains during growth? To answer the first question it is necessary to determine the crystallographic orientation of the lamellae of each phase relative to one another. This has been done for Al-CuAl2 eutectic alloys by two different techniques on specimens prepared in different ways.2&apos;3 The results were different from each other and from a third orientation relationship between A1 and CuA1, reported for overaged A1-Cu alloys.4 The three orientation relationships are summarized below to illustrate their similarities and their differences. (001) ? 11 (001) A1; [l00] ? 11 [l00] Al Eutectic, Ref. 2 (001) 8 1) (001) A1; [1001 ?11 [1101 A1 Eutectic, Ref. 3 (001) ? 11 (001) A1; [l00] ? 11 [310] Al; Widmanstfitten, Ref. 4 It is not surprising that different orientation relationships were found by Ellwood and Bagley,&apos; and Takahashi3 since the solidification conditions were quite different. Nor is it surprising that Mehl, Barrett, and Rhines 4 found still another value since they were studying another type of alloy. Nevertheless, it would be expected that some logical and systematic pattern could be found if all the alloys were at equilibrium since the same two phases are

Jan 1, 1962

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.&apos; It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963