Search Documents

By D. P. Pope, T. Vreeland

Observations of dislocations in zinc using Berg-Barrett X-ray micrography confirm the validity of a dislocation etch for (1010) surfaces. A technique for measurement of the depth in which dislocations can be imaged in X-ray micrographs is given. This depth on (0001) surfaces of zinc was found to be 2.5 µ using a (1013) reflection and CoKa radiation. BUCHANAN and Reed-Hill (B & RH) have recently questioned the ability of a dislocation etch to reveal all of the basal dislocations which intersect (1010) surfaces in annealed zinc crystals.' This etch was developed by Brandt, Adams, and Vreeland who conducted a number of different experiments to check its ability to reveal dislocations.2,3 B & RH prepared (0001) foil specimens for transmission electron microscopy from annealed crystals and observed dislocation densities of about l08 cm per cu cm in the foils, while the etch indicated densities of the order of l04 cm per cu cm in their annealed crystals. As this etch has been used in a number of studies of dislocations in zinc, it is of considerable importance to reassess its validity in the light of the B & RH results. The X-ray work reported here was undertaken to check the ability of the etch to reveal dislocation intersections on (1070) surfaces of zinc. The X-ray technique was chosen for this check because it could be applied to the as-grown crystals with a relatively small amount of specimen preparation. We believe that the possibility of accidental deformation in preparation of the bulk specimens is considerably less than that for thin foil specimens suitable for transmission electron microscopy. Unfortunately, basal dislocations are not visible on Berg-Barrett topo-graphs of (1010) surfaces, which are the surfaces on which the etch is most effective. Therefore, a one-to-one correspondence between the etch and X-ray observations could not be made. Basal dislocations near (0001) surfaces have been observed by Schultz and Armstrong4 using the Berg-Barrett technique, but they did not report the as-grown dislocation density observed in their crystals. We have applied the X-ray technique in this study to surfaces oriented from 1 to 2 deg of the (0001) to determine the basal dislocation density, and have compared this density with that observed using the etch on a (1070) plane of the same crystal. The X-ray observations permit determination of the depth in which basal dislocations can be observed under the diffracting conditions used. SPECIMEN PREPARATION High purity zinc crystals are very soft, so a good deal of care must be exercised in the preparation of observation surfaces. As-grown crystals approximately 2.5 cm in diam and 20 cm long were acid cut into 1.25 cm cubes. A thin slab was cleaved from an (0001) surface to produce an accurately oriented reference surface on the specimen. Some of the cubes were examined in the as-machined condition while some were annealed in argon at 410°C for 2 hr. Heating and cooling rates were less than 2°C per min. Some of the specimens were scratched on a (0001) surface with a razor blade to produce fresh dislocations. Approximately 2 mm of material was acid lapped from one face of a cube to produce a surface oriented between 1 and 2 deg from the basal plane and parallel to the [1210] direction. A (1070) surface was also acid lapped. The lap used a 1 to 3 pct solution of HN03 in water to saturate a soft cloth which was backed by a stainless steel plate. The cloth was moved over the crystal surface at a rate of 20 cm per sec while a normal force of about 4 g was maintained between the cloth and the specimen. As-lapped surfaces were examined as were surfaces which were chemically and electrolytically polished after lapping. The small angle between a lapped surface and the (0001) plane was measured to 0.1 deg using a Unitron microgoniometer microscope (the cleaved surface was used as a reference in this measurement). The microscope was modified so that the intensity of reflected light could be continuously monitored on a meter. This modification produced nearly a ten-fold increase in the reproduceability of orientation readings. OBSERVATIONS The Unitron Microgoniometer observations indicated that the lapped surfaces had a terraced structure with the terraces quite rounded and spaced about 0.1 mm in the [1010] direction. The maximum change in slope between terraces was 0.25 deg, indicating a terrace height of about 0.1 µ. A Unitron measurement of the average angle between (0001) and a lapped surface was checked by micrometer measurement of the specimen and found to agree within 0.1 deg. The Berg-Barrett micrographs using (1013) reflections and CoKa radiation5 revealed subboundaries, short dislocation segments, spirals, and loops near the surfaces which were oriented from 1 to 2 deg of the (0001). Micrographs of surfaces prepared by lapping appeared very similar to those of the chemically and electrolytically polished surfaces. The loops and spirals were not extinct in (1013) or (0002) reflections, indicating that they have a nonbasal Burgers vector. Extinctions of the short, straight dislocations indicated that they belonged to an (0001)(1210) system. Fig. 1 is an example of a micrograph which shows a subboundary, and dislocation segments which are pre-

Jan 1, 1970

By A. M. Rowe, I. H. Silberberg

A computer program was written to predict the phase behavior generated by the enriched-gas-drive process. This program is based, in part, on a new concept of convergence pressme, which is then used to select vapor - liquid equilibrium ratios (K-factors) for performing a series of flash calculations. The results of these calculations are the equilibrium vapor and liquid phase compositions which define the phase envelopes. The program was used to predict phase envelopes for 11 different hydrocarbon systems on which published experimental data were available. The predicted and experimental results compare favorably. INTRODUCTION The reservoir engineer is frequently faced with the problem of predicting what will happen if gas is injected into a reservoir. One aspect of this, general problem is predicting the phase changes that will occur when a non-equilibrium gas displaces a reservoir fluid. In particular, a "dry" gas, upon displacing a volatile oil, will pick up intermediate components from the oil. On the other hand, a "wet" gas, containing a high concentration of intermediates, will lose some of these components to a relatively low-gravity, non-eouilibrium1- crude. It is this latter Drocess. occurring in the enriched-gas displacement, which is treated in this paper. In the past, these phase changes have been determined experimentally and the results incorporated into various modifications of the Buckley-Leverett analysis.112 Such experimental work is time consuming, and the results are sensitive to numerous experimental errors. With the wide availability of high-speed digital computing equipment and numerous correlations pertaining to the vapor-liquid equilibria of hydrocarbon systems, it is now practical to calculate such phase behavior. This paper describes a computer program for performing these calculations. THE ENRICHED GAS DISPLACEMENT PROCESS Experimental results have shown that oil recovery can be significantly increased by enriching the displacing gas with intermediate hydrocarbon c0m~onents.3 The essential features of the phase behavior generated by this enriched-gas-drive process are commonly illustrated with ternary diagrams such as Fig. 1.4 In this figure, Gas D, which contains a high concentration of intermediate hydrocarbons with respect to the undersaturated Crude A, is injected into the reservoir. When D contacts A, gas goes into solution until the oil becomes saturated (Point. B). Further contacting of Gas D and saturated Oil B results in a Mixture C which separates into Vapor Y(c) and Liquid X(c). Liquid X(c) is contacted by additional Gas O, resulting in Mixture E which separates into Vapor Y(e) and Liquid X(e). Repeated contacts of the liquid by the injected gas will eventually result in Liquid X(4 of maximum enrichment existing in equilibrium with Gas Y(d). The equilibrium tie-line X(4 Y(4, when extended, passes through the Point D representing the enriched injection gas. For systems of more than three components, the predicted equilibrium states are dependent upon not only reservoir temperature and pressure, but also the compositions of the crude oil and injected gas. If the gas is sufficiently enriched, a miscible displacement is generated. Line If is tangent to the phas,e envelope at the critical point (Point Z) and represents the limiting slope of the tie-lines as the critical state is approached. Point 1 therefore represents the minimum enrichment of injection gas required to generate a miscible displacement. Point G represents the minimum enrichment required for initial miscibility of the injection gas with Crude A. Accra has presented a method to be used for prediction of oil recovery by the enriched gas displacement process.l To develop the phase behavior data needed, he designed the experimental procedure described in the following quotation from his paper: The original liquid was contacted by a volume of displacing gas and allowed to come to equi-

Jan 1, 1966

By Robert E. Tally

A recorded in the account of the Annual Meeting, on another page, the report of the tellers showed that all men nominated by the committee, which included Messrs. Wilber Judson, E. DeGolyer, W. A. Weldin, J. A. Norden, J. D. MacKenzie, Wilfred Sykes and S. Skowronski, were duly elected to the offices for which they were nominated. Robert Tally, who was elected to the presidency for 1931-2, is well known to all our members not only because he has served on the Board of Directors since 1928, but through a brief outline of his great achieve¬ments in his chosen profession pub¬lished in our issue of December last. The vice-presidents, Howard N. Eavenson and H. A. Guess, are also well known to our members. Mr. Eavenson has not only been chairman of the Coal Division since its organization, but was also a Director during 1917, 1918 and 1919., Mr. Guess was Director in 1926, was elected a vice-president by the Board last year to fill the vacancy created by the election of Mr. Bassett to the presidency, and is now elected to the usual three-year term.

Jan 1, 1931

By R. J. Miller, W. A. Bates

ALTHOUGH cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowy1 in 1930, which presented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids ; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. CONSTITUTION AND PROPERTIES Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen

Jan 1, 1946

By A. W. Griffith, R. G. Beverly, W. A. Millsap

THE Grand Junction Pilot Plant, operated by National Lead Co. Inc., for the U. S. Atomic Energy Commission, is engaged in the amenability testing of orebodies to establish design and cost data for commercial mills and to test new processes for recovery of uranium from ores. Test work was performed to study the effects of several variables on leaching of uranium ores in carbonate solutions. Many of these variables had been investigated in the laboratory, but pilot plant tests were desirable to evaluate their importance in semi-works equipment and to predict optimum operating conditions for future commercial mills. The results of these tests should serve as a guide in selecting the most efficient and economical method of leaching uranium ores amenable to a carbonate process. This article is concerned with a process in which uranium is extracted from the ore by a hot Na2CO3- NaHCO3 solution; the uranium-bearing solution is separated from the solid residue by filtration, and uranium is then precipitated by chemical means.

Jan 9, 1957

By Donald H. McLauqhlin

ITEM expressed in billions of dollars have become so commonplace these day- that a mere statement of the latest figures for the country s gold reserve scarcely conveys m adequate sense of the immensity of the commitment the nation has made in building up its huge stock, two-thirds of which is now stored at Fort Knox. Kentucky. Only by measuring it against quantities that mean something tangible to a particular group can an adequate comprehension of its magnitude he rained; consequently, to mining engineers, a comparison with the value of output from well-known mining districts might best serve to give some degree of reality to the astronomical figure at which the country gold is now valued.

Jan 1, 1941

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, aged 36. Experienced copper metallurgist and mining geologist. Familiar also, through 15 years' broad practical experience, with mining, cyanidation, concentration (including oil flotation), metallurgical accounting, and mine and plant management. Best references. No. 237. Member, graduate engineer with 10 years' experience in malleable, gray -Iron, and steel, as chemist., metallographist, and metallurgist. Researches and investigations by laboratory methods and under works conditions. No objection to some routine. No. 243. Member, technical graduate, broad experience in coal, oil, and clay. Will go anywhere as mining geologist after Sept. 1, 1915. No. 244. Member, technical graduate, aged 30, married, with over 10 years' experience as chemist, engineer on construction, superintendent and general superintendent of bituminous coal and coke plants. SpeaksSpanish. References. No. 245. Member, open for engagement as mine safety inspector or as superintendent of bituminous coal mine. No. 246. Member, graduate mining engineer, with five years' experience in coal mining as mining engineer, construction engineer, pit boss, and superintendent, open for engagement. Best references. No. 247.

Jan 9, 1915

By JOHN R. SUMAN

TONIGHT I want to speak of the current problems and the postwar difficulties facing American industry. American industry has done an outstanding job in adjusting its operations to wartime necessity. The national income for 1942 was nearly $120,000,090,000 and of this outlay approximately $55,000,000,000 went for war material. The enormity of the expenditures for war material is indicated by the fact that the expenditures for war purposes alone were greater than the annual gross national income in the period 1931-34. This tremendous production job in turning out a record output of war products was accomplished by industry in spite of a large number of restraining and hampering influences, and I want to mention several of the more important problems.

Jan 1, 1943

By Henry G. Petrow, Edward S. Porter

MAJOR occurrences of lignite with significant uranium concentrations have been reported in western parts of the Dakotas, especially in Harding County, S.D., and Billings and Slope counties, N.D. Samples containing as much as 2 pct U3O8 were received at the Winchester Laboratory, but those deposits reportedly of major significance have generally contained 2 to 4 lb of uranium per ton of lignite. Most of the uranium appears to be associated with the carbon in the lignite as a urano-organic complex, although in most instances analysis of inorganic material has shown uranium values. Molybdenum is similarly associated with the carbon, and its concentrations generally parallel the uranium. The noncarboniferous material is mainly composed of gypsum, jarosite, bentonite, sandstone, and miscellaneous carbonates and silicates. The heating value of these lignites has been determined as about 3500 Btu on a dry lignite basis. The ash content of lignite has varied widely, the important samples containing 30 to 60 pct ash on a dry lignite basis. Because of the significant upgrading of uranium values obtained by ashing the lignite, and because recovery of uranium from raw lignite presented formidable processing problems, major emphasis at Winchester has been placed on devising methods to recover uranium from lignite calcines. Proper roasting removes the problem of organic fouling of solutions, reduces the size of the leaching plant for an equivalent uranium throughout, and generally provides equal or better acid leaching efficiency with less acid than can be obtained from the raw lignite.

Jan 9, 1957

By Charles White Merrill

Mankind's progress is measured in minerals. Man's emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate-and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium metal did not appear as a commercial product until 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1964

By R. S. McClellan

DURING the last year or so, with higher prices for gold and silver, many old properties in the West have come back to life. Almost every profitable producer in the old days has been considered, and the reasons for its shut-down investigated. If it seems likely that modern ore-finding, mining, and metallurgical methods, and S35 gold can again put the property on a profitable basis, someone can usually be found to back the venture. Methods of rejuvenation vary with the property, of course, but the following outline of what has been done with one group of mines in Idaho is fairly typical and may be suggestive to others. The Golden Chariot gold-silver properties, near Silver City, consist of seven old mines, working a vein system striking north and south, which had a productive length of some 3500 ft. The vein is a quartz-filled fissure with granite walls. Gold occurs in native, and with silver in the form of electrum which is the natural alloy of the two metals. Silver also occurs in a variety of sulfides. From 1064 to 1876, these old properties were worked intensively to an average depth of about 700 ft., through seven shafts which range in

Jan 1, 1934

By K. Sassa, I. Ito

The dynamic principal stresses induced within rock by an explosion under con fined conditions are analyzed for the case of blasting with one free face by applying the values of measured radial displacement, particle velocity and so on to equations derived from the theory of elasticity. The dynamic stresses on the free face are also calculated from the strain measured by wire strain gauges affixed on the free face. Some results obtained are briefly: 1) The maximum stress on the free face appeared at the intersection between the free face and the burden, and its magnitude was about twice as large as the magnitude of the tangential tensile stress imparted by the incident stress wave within the range related to the breakage by blasting. 2) The maximum value of the compressive stress near the free face was decreased due to the existence of the free face, while that of the tensile stress was increased. 3) At any point near the free face, the directions of the principal stresses in the r? plane using spherical coordinates with the origin at the center of the spherical charge, changed with time except in the direction of the burden. However, at another point near the explosion point where the principal stresses were mainly those stresses caused by the initial longitudinal wave, the directions of the principal stresses coincided with those of the coordinate used. 4) The maximum value of the tensile stress in the F direction was larger than those in the re plane at and near the free face. 5) The tensile stress caused by the Hopkinson effect appeared only near the burden. 6) It is presumed from the results of stress analysis that radial cracks will be produced in the rock mass near an explosion point, but with the approach of the free face, the directions of cracks curve towards a direction parallel to the free face. INTRODUCTION In order to investigate the mechanism of rock breakage by blasting, it is considered to be very im- portant to know how the stresses are generated and distributed within the rock by explosion of a confined charge. As part of a research program concerning the mechanism of rock breakage by blasting, the authors have already published papers on the detonation pressure produced at the inner surface of the charge hole1 and on the behavior of the dynamic stresses within rock caused by an explosion in the case where no free face existed.' In this study the dynamic stresses on and near the free face have been investigated for the case of blasting with one free face. The mechanism of rock breakage in blasting is discussed in the light of these studies.

Jan 1, 1967

By J. M. Callow

H. A. MEGRAW, New York, N.,Y.-One interesting thing that might be brought out in this connection is the cost of making sulphide gas. I had a communication the other day which suggested that, in view of the high cost of oil, sulphur and sodium sulphide, we might make use of a well-known chemical reaction to form this sulphide gas by the use of aluminum sulphide. It is difficult to see any advantage in this, however, since aluminum has been affected just as much as any other commodity by the rise in prices, due, to war conditions. RUDOLF GAHL, Miami, Ariz. (communication td the Secretary*) Mr. Callow refers to my paper, History of Flotation at Inspiration, which was presented at the Arizona meeting of the Institute. These notes of Mr. Callow's contain much valuable information on flotation practice, as is to be expected from an article written by an author of Mr. Callow's experience in this branch of metallurgy. Nevertheless, I cannot help contradicting a number of the statements made in the references to my paper. In passing, I will also say a word about the reference in Mr. Callow's paper to the article by Messrs. Laist and Wiggin entitled "Flotation Concentration at Anaconda, Mont." Mr. Callow calls attention to the fact that evidently Callow flotation machines are not very sensitive, inasmuch as one man per shift handles four 800-ton sections of Callow machines or 3,200 tons per day at the Inspiration plant. While-it has been the experience of the Inspiration company that the four sections of Callow machines in the Inspiration concentrator are easily handled by one American operator per shift, it is only fair to state that each man operating four sections is assisted by two Mexican helpers who constantly clean the bottoms of the machines. The tonnage per section, by the way, whether equipped with Callow,, Inspiration or Minerals Separation machines, is considerably in excess 4 800 tons.. Mr. Callow further says that local opinion at Inspiration is that, two 800-ton sections consisting of two 10-compartment and four 6-compartment Minerals Separation machines (these machines are of the Hebbard type) is the limit that one man can properly attend. I do not hesitate to say that I consider it perfectly feasible to have four such sections operated by one man, perhaps assisted by "one helper. The Minerals Separation machines of this type have undoubtedly an advantage as far as easiness of operation is concerned,

Jan 4, 1917

By T. S. Lundy, R. E. Pawel

Effects of short-circuiting paths on observed diffusion behavior in real crystalline systems are considered. It is concluded that experimentally measured diffusion coefficients may vary widely from values associated with true lattice diffusion to those appropriate for short-circuiting paths alone depending upon the conditions of the experiment and the sensitivity and completeness of the data. IN 1961 Harrison1 classified experimentally observed diffusion behavior in systems involving both lattice and dislocation-enhanced atomic transport into three categories. His types A and C were limiting cases where the measured diffusion coefficients using the usual serial sectioning techniques were representative of lattice diffusion (with only slight effects of dislocations) and dislocation-network diffusion (with only slight effects from lattice diffusion), respectively. In both cases A and C for a sectioning experiment in which the diffusion couple has the semi-infinite geometry and unidirectional diffusion takes place from a plane source located at the origin of the coordinate system, he pointed out that Gaussian penetration behavior should be observed. For case A the lattice coefficient should be slightly enhanced by dislocation contributions, and the model of Hart2 can be used to predict the amount of this enhancement. For case C the observed coefficient should be that for the dislocation network and have little or nothing to do with lattice diffusion. Hart's model in its general form is still applicable, but the apparent diffusion coefficient for this case is virtually independent of dislocation density. Harrison's case B is that for which non-negligible contributions exist for transport by both mechanisms and "the concentration distribution does not approximate to any simple form." With the possible exception of very low temperatures where diffusion distances approach atomic dimensions, any real diffusion specimen will in general show non-Gaussian behavior provided the data are complete enough to uncover it. Thus, a "complete" set of data for any real system cannot be expected to be totally amenable to treatment by a simple mathematical model which does not take into account the relative distribution of transport by the various modes or submodes. For a particular sensitivity of specimen analysis and at a given temperature of annealing if the concentration profile could be observed as a function of time, "the behavior will initially be type C, and will develop into type B. and ultimately type A".1 Thus, it appears that the type of diffusion behavior which is experimentally observed in a given system depends very much upon the particular experimental conditions and the particular tools available to obtain the data. Interpreted in this fashion, Harrison's classification refers not to the diffusion behavior as a whole but to the relative sensitivity of the method of examination and completeness of the data. In the present paper we will: 1) assume that the measured penetration behavior follows the same general classification as that proposed by Harrison; 2) give, for diffusion in tungsten, examples of the range of diffusion coefficients that it is possible to obtain in a single experiment; and 3) speculate that some arguments which consider the possibility of short-circuiting effects being responsible for "anomalous" diffusion in several bcc metals may have been discarded prematurely.3 Both monocrystalline and polycrystalline tungsten were used in this work. The former was obtained as triple-pass, electron-beam zone-refined 6.0-mm-diam rod from Materials Research Corp.. Orange-burg. N.Y. The latter was swaged, high-purity bar stock which was annealed for 2 hr at 2200°C and 10-9 torr to yield an average grain diameter of about 25 /i. The tracer Nb95 was received in oxalate solution from the Isotopes Division, Oak Ridge National Laboratory. Experimental procedures of specimen preparation, isothermal diffusion annealing, serial sectioning by anodizing-and-stripping, and y counting of the individual sections to determine the tracer penetration profile after a given diffusion anneal have been described elsewhere.4 However, it should be noted that the anodizing-stripping sectioning technique has the particular advantage for this research of permitting sectioning to be accomplished over a wide range of

Jan 1, 1970

By Franklin Allison

THE influence of cobalt and nickel on the properties of steel might be readily expected to be very similar. The two elements occupy close and somewhat unusual positions in the periodic table, their chemical behavior and compounds are so completely analogous and their various physical properties, including the ferro-magnetic characteristic, show such a remarkable correspondence, that there is no doubt of a strong resemblance existing between these two metals. However, the variety of, properties that are obtained from steel is due, largely to the fact that the element iron possesses allotropic forms. Alloying elements that affect these allotropic forms, or alter the nature of the allotropic changes, exert a profound influence on the resulting steel. In the case of nickel and cobalt, although these elements are very similar chemically and physically, it is found that they differ distinctly in their individual effects on the critical points of iron. Both nickel and cobalt form a series of homogeneous solid solutions with iron at temperatures above 1800° F. The difference in their behavior does not occur until changes begin to take place in the solid state below this temperature. An inspection of the respective thermal equilibrium diagrams at the lower temperatures makes the opposite effects of nickel and cobalt clearly evident.

Jan 3, 1927

By AIME AIME

AMONG the industrial motion pic¬tures released in the last year of possible interest to people in the mining industry are the following: "A New World Through Chemistry," made by the public relations department of E. I. du Pont de Nemours & Co., Wilmington, Del. This film, which is in sound and color, interprets in twenty minutes of narration and ingenious photography many of chemistry's newest developments. It may be borrowed either in 16-mm. size on an 800-ft. reel, or 35-mm. size on a 2000¬ft. reel, the only charge being the cost of returning the film. Douglas D. Rothacker, 729 Seventh Ave., New York City, is prepared to loan free of charge except for transportation each way several films prepared in the plants of the International Nickel Co., 16 mm. with sound. These include: "Nickel High Lights," 35 minutes; "Nickel Mining," 18 minutes; "Nickel Smelting," 18 minutes; "Nickel Refining," 9 minutes; and "Copper Refining," 6 minutes.

Jan 1, 1941

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By Dwight E. Woodbridge

DuriNg April, Max, and June, 1910, I was in charge of an examination of the greater part of the Moa iron-ore area in Oriente Province, Cuba, on the north coast, near the east end of the island. My instructions, on arrival at the properties, were to check former estimates of tonnages and grades, and to re-examine the ore comprised in claims covering 44,727 acres. This work included the running of lines dividing the properties into co-ordinate planes, the boring of many thousand feet of holes spaced at the intersections of these co-ordinates, the taking of samples of the ore penetrated, the analysis of these samples for their various constituent minerals, and the determination of the results as to tonnages, depths, and grades, both for individual properties and for the entire group. Each section of every one of the thousand holes drilled was to be compensated for depth and grade with every other, a series of simple arithmetical calculations of no slight magnitude, the mere mechanical labor of which consumed much time, but finally resulted in giving a complete average of all the essential facts for the entire area of 18,000 hectares, Had it not been for the more than willing, active, and able co-operation of the officers of the Spanish-American Iron Co., from Charles F. Rand, President, and Jennings S. Cox, General .Manager, down to the most humble water-carrier, the work would have consumed far more time than it did. The lands thus systematically explored by me were comprised in the following denouncements: Punta Gorda, Yaminiguey, Baracoa secunda, Sagua, Moa, Yajrumaje, Lirio, and Cabanas, all of which were massed as the Moa group, so called, and cover an area of 13,832 hectares, or 34,179 acres. Some 10,000 acres additional to this was included in neighboring properties, lying between Moa and the east end of the island, the Buena Vista,

Jan 1, 1912

By W. A. Bates, R. J. Miller

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947

By R. J. Miller, W. A. Bates

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947