Search Documents

By R. W. Smith, M. E. Brookes

The temperature at which th: quenched 0' (ordered bcc) phase transfo.rms to the ( (complex hexagonal) phase on heating has been examined for certain Ag-Zn and Ag-Au-Zn alloys using an electrical resistivity method. The transition temperature decreases by approxinzately 7°C as the zinc content is reduced by 1 at. pct. The critical temperature, Tc, for long-range order has also been measured for a number of Ag-Au-Zn alloys. Extrapolation to zero gold content suggests that Tc decreases by approximately 5°C per 1 at. pct reduction in zinc content. The 0 phase of the Ag-Zn system exists over a narrow range near the composition Ag zn,' Fig. 1, and has a bcc structure which is disordered above 272°C. Slow cooling to temperatures below the range 274"/258"C allows the complex hexagonal phase, r° to form.2 This is the stable structure at room temperature.3 Upon quenching 0 -phase alloys from high temperatures, it is found that the 0 — (' transformation is suppressed; but ordering takes place (i.e., 0 -0'). This ordered structure can also be obtained by the room-temperature aging of cold-worked (0.4 Deformation of the 0' phase gives rise to a fur- ther hexagonal phase ( (of nearly ideal axial ratio) which reverts to b' within a few hours.= In view of this, it has been suggested that the equilibrium struc-

Jan 1, 1969

At 8 o'clock on the evening of Thursday, July 25th, the special train chartered by the Provincial Government for the Institute's use, pulled out of Toronto. Ten parlor cars and two dining cars made up the train. The culinary arrangements were under the personal supervision of Mr. McConkey, of Toronto. [ ] The Hon. Frank Cochrane, Minister of Mines, Lands and Forests, was the efficient host of the party. He was assisted by the Hon. Dr. Pyne, Minister of Education, and by Mr. T. W. Gibson and Dr. W. G. Miller. On arriving at Cobalt, the delegates were met by the following Committee Mr. A. A. Cole, representing the T. & N. 0. Railway; Messrs. R. W. Leonard and D. B. Rochester, deputies from the Cobalt Chamber of Mines ; Messrs. Run¬ning and Martin, from the Cobalt City Council; Messrs. McLeod and Ferland,

Jan 1, 1907

NEW MEMBERS The following list comprises the names of those persons Who became members during the period July 10, 1918, to Aug. 10, 1918. ARCHER, EUGENE G., assayer and Chem., Granby Cons. Min. Smelt. & Power Co.,Anyox, B. C., Canada. BAKER, ROBERT C Mech. Engr. and Draftsman, Moctezuma Copper Co., Nacozari, Son., Mexico. BARNES, EDWARD A Supt., Fort Wayne Works, General Electric Co., Fort Wayne, Ind. BARNHART, EDWIN Engr. of Tests, Bethlehem Steel Co., Sparrow's Point, Md. BENSLEY, MAURICE D Pres. and Mgr., Frontier Brass Foundry, Inc., Niagara Falls, N. Y. BRADLEY, JOHN C Met., The American Brass Co., Waterbury, Conn. BRAGG, C. T Works Mgr., Michigan Smelt. & Refin. Co., Detroit, Mich. BRYMER, GEORGE W Min. Engr., 922 Union National Bank Bldg., Scranton, Pa. CHIVVIS, NORMAN Met. Engr., More-Jones Brass & Metal Co., 3144 North Broadway, St. Louis, Mo. CRAWFORD, R. D Prof. of Mineralogy & Petrology, Univ. of Colorado, Boulder, Colo.

Jan 9, 1918

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world's produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

By J. R. Low

The brittle fracture of a Tic-lnconel cermet at room temperature is shown to occur primarily as a result of the cracking of the larger carbide particles (at a tensile strain of approximately 0.3 pct), followed by cracking of adjacent, smaller carbides and, finally, by the rupture of the lnconel matrix between cracked carbides (at a strain of-1.2 pct). No evidence was found for separation at the interface between carbide and matrix at any point in the fracture process. MATERIAL used in this study was a Tic-Inconel cermet prepared by infiltration (50 pct Tic, 50 pct Inconel: designated as TC66-I). A thin section of this material was brazed to a piece of low carbon steel and then mounted in lucite for metal-lographic preparation." After grinding, polishing, Deformation and fracture of the specimen was accomplished by bending the specimen as a simply supported, centrally loaded beam, in a bending fixture which could be placed in the stage of a microscope, with the tension side of the bend specimen under the microscope objective.? This method of deformation and observation has the advantage that the surface under examination is the most severely deformed portion of the specimen. The procedure followed was to deform the specimen a small amount, scan the surface at Xl OOO for any evidence of deformation or cracking, deform another small increment, scan the surface again, and so on until a

Jan 1, 1957

Jan 1, 1970

By J. D. Miller

The authors have summarized the state-of-the-art in the kaolin clay industry very well. In some instances the problems which they have identified are common to all fine particle separations and in other cases the problems are unique to the kaolin clay industry itself. General areas of research which may be common to other systems and which deserve continued investigation at a higher level of support include: 1) Establishment of the relationship between flotation response and clay structure/composition. 2) Determination of temperature effects in the separation of fine particles. 3) Evaluation of the effect of bubble size on the quality of fine particle separation. The first two areas would require basic surface chemistry studies including microflotation, electrokinetics, adsorption density measurements, and microcalorimetry. The last area would be oriented toward the mechanics of bubble-particle attachment. Regarding the first area, the authors alluded to this research need by commenting on the variation in separation observed from one deposit to another. It seems that a detailed study characterizing the flotation response of various clay types with respect to structure and compositional features would be of considerable value. For example, I understand, that D. W. Fuerstenau's group has recently been successful in characterization, with respect to structure, of some silicate mineral types--chain, sheet and framework silicates. A similar study should be initiated in which the flotation behavior of various clay minerals kaolinite, halloysite, montmorillonite

Jan 1, 1979

By M. Semchyshen, A. P. Coldren, W. G. Scholz

A survey of the Fe-Mo-B system was made to determine the extent to which boron might affect the microstructure and strength properties of iron-rich Fe-Mo alloys. Seventeen vacuum-induc tion melted ingots were prepared with approximate mo-lybednum contents 01 2, 4, 9, and 19 wt pct and approximate boron contents of 5, 14,50, and 630 ppm by weight. Phases extracted from annealed specimens and identified by X-ray diffraction analysis included E Fe3MO2, Mo2FeB2, and an oxide hazling a diffraction pattern practically identical to that of MnFez04. Three types of alloy strengthening were observed: a) Fe-2 pct Mo-B alloys were hardenable by a bainitic-type transformtion of austenite to ferrile; b) Fe-4 pct Mo-B alloys were hardened by the solid-solution mechanism; and C) Fe-9 pct Mo-B and Fe-19 pct Mo-B alloys were hardened by precipitation of the E Fe3Moz phase. Boron was observed to have a very strong hardening effect in the Fe-2 pct Mo alloys and a mild strengthening effect on the 1200°F properties of the Fe-4 pct Mo alloys. In the Fe-9 pct Mo alloys there was no consistent effect of boron on strength at either room temperature or 1200° F. The Fe-19 pct Mo alloys were so brittle that meaningful tensile or creep-rupture data could not he obtained. No dispersion hardening from borides was recognized in any of the alloys. THE high-temperature properties of iron-rich Fe-Mo alloys were studied by Reiter and Hibbard.' They found that the strength of the alloys increased markedly as the molybdenum content was raised from 0 to 15.9 pct by weight. The authors explained the various degrees of strengthening in terms of a) solid-solution strengthening, b) strengthening from a martensitic-type transformation, and C) precipitation strengthening. The objective of the present investigation was to conduct a survey of the iron-rich portion of the Fe-Mo-B system to determine whether the beneficial effects of molybdenum on the strength of iron can be enhanced by the presence of boron. It was thought that perhaps fine dispersions of molybdenum- rich borides would be found which could improve the high-temperature strength of ferritic alloys beyond the strengths attainable by molybdenum additions alone. Also, it was considered worthwhile to study the effects of boron in alloys which are essentially free of carbon. Most, if not all, of our present knowledge about boron in high-temperature alloys pertains to alloys containing carbon and carbides. EXPERIMENTAL PROCEDURES Alloy Preparation. Seventeen 8-lb ingots were prepared from electrolytic Plastiron, unalloyed molybdenum chips, and boron powder by a vacuum-induction melting procedure employing hydrogen as the main deoxidizer. The alloys were melted in alumina crucibles using 35-lb melts, with each melt being split four ways to achieve varying boron contents within four Fe-Mo base compositions. The results of chemical analyses conducted on chips machined from the chilled ends of the ingots are presented in Table I. The boron analyses were performed by a spectrographic method utilizing primary standards prepared from boric acid. They indicated that in ingots to which no boron was

Jan 1, 1964

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

By Cyril Stanley Smith

Jan 1, 1949

By Cyril Stanley Smith

Jan 1, 1949

By Dennis K. Mortensen

Startup of the 9000 tpd Sacaton concentrator is expected to increase Asarco's domestic copper concentrate capacity by 21%. The plant site is located due west of the mining operations, consisting of both crushing and concentrating facilities. Arthur G. McKee & Co. served as the prime contractor for the project. The Sacaton mineralization contains both sulfide and oxide ores. Primary mineral constituents are chalcocite, azurite, malachite, chrysocolla, and minor amounts of silver and occasional gold. Sulfides are distinguished from oxides when more than half the total copper content is in the form of a sulfide copper mineral. While non-sulfide copper minerals are considerably less prevalent throughout the orebody, they tend to occur quite intimately with the sulfide minerals, particularly in the upper zones of the mineralization. For this reason the decision was made to treat all the ore in a flotation circuit using existing sulfidizing methods.

Jan 11, 1974

By W. F. Hosford, E. W. Kelley

By testing polycrystalline specimens from textured plates which had Previously been used to provide materials for growing single crystals, it has been possible to relate the plastic anisotropy of textured materials to the deformation behavior of single crystals. The deformation studies have been conducted at room temperature on textured polycrystalline magnesium and binary Mg-Th and Mg-Li alloys. Variously oriented specimens of the textured materials were deformed in plane-strain compression and in uniaxial tension and compression. The stress-strain curves are similar in their general jorm of anisotropy and stress levels to those obtained on single crystals of the same alloys. The degree of anisotropy is lower, however, in the polycrystalline materials and correlates with the intensity of the basal texture. Yield loci for the textured materials appear reasonable in terms of the deformation mechanisms, and deviate sharply from the form predicted by the Hill analysis for aniso-tropic material. A N earlier study1 of single crystals has shown that magnesium and magnesium alloys with thorium and with lithium deform at room temperature primarily by basal slip, {10i2) twinning, and (1011) banding. The (10i1) banding mode is a combination of {10ll) twinning followed by (1012) twinning and basal slip within the doubly twinned material.2, 3 Magnesium with lithium can also deform by {1010)(1210) prism slip.1'4'5 Still other deformation modes have been reported for magnesium6-11 but these are considered to play a minor role in room-temperature deformation. In a polycrystalline material, plastic deformation must occur in the individual grains through the operation of one or more of the various deformation modes. Because the critical shear stress for basal slip is very low compared to the activation stresses for the other deformation modes,' basal slip accounts for much of the deformation in the polycrystalline aggregate. However, since there are only two mutually independent basal slip systems, and because five independent systems must be active for an arbitrary shape change in any material,'' modes other than basal slip must account for some of the strain. The deformation of textured magnesium, like that of other hcp metals, must be controlled by the same mechanisms observed in single crystals. In strongly textured material, the form of the anisotropy should be similar to that of single crystals, and the degree of anisotropy should depend on the intensity of the texture. EXPERIMENTAL PROCEDURE The anisotropy of deformation was investigated through the use of plane-strain compression tests, as well as uniaxial tension and compression tests. Materials. Test specimens were cut from the three textured plates of magnesium which had previously been used to provide material for single crystals.' These plates, furnished by Dow Chemical Co., had been reduced about 80 pct during the process of being hot-rolled to their final 1/4-in. thicknesses. The plates had the three respective compositions, pure magnesium, Mg-0.5 wt pct Th (0.49 pct Th by spectro-graphic analysis), and Mg-4 wt pct Li (3.84 pct Li by chemical analysis). Impurities other than iron were less than 0.0005 pct Al, 0.01 pct Ca, 0.001 pct Cu, 0.0006 pct Mn, 0.001 pct Ni, 0.003 pct Pb, 0.001 pct Si, 0.001 pct Sn, and 0.01 pct Zn. Iron was 0.001 pct in the pure magnesium, 0.002 pct in the Mg-0.5 pct Th, and 0.014 pct in the Mg-4 pct Li. The textures of the three plates were determined by X-ray diffraction utilizing only the reflection technique out to an angle of 50 deg from the sheet normal. The resulting basal pole figures are presented in Figs. 1, 3, and 5. Grain sizes in the plates were ASTM number 4 in the pure magnesium and number 7 in each of the alloys. Plane-Strain Compression Tests. Plane-strain compression specimens approximately $ in. thick by 4 in. wide by $ in. long were prepared for each of the three compositions. These specimens were prepared in a manner similar to that used for the single-crystal specimens of the earlier study.' All polycrystalline specimens were stress-relieved at 500°F for hr as the final step in their preparation for testing. The testing procedure was identical to that used for the single crystals, involving compression in a channel and using 2-mil Teflon film as a lubricant. The specimens were tested in six orientations of interest, these being the six combinations of the rolling, transverse, and thickness directions of the material serving as loading, extension, and constraint directions in the plane-strain compression test. Each of the six orientations was assigned a two-letter identifying code. These are combinations of the letters (thickness direction), R (rolling direction), and T (transverse direction) with the first letter signifying the loading direction and the second letter the extension direction. For example, ZR specimens were compressed in the thickness direction while extension was permitted to operate in the rolling direction of the textured material. To facilitate comparison of the present work with that of the single-crystal study1 the orientations used for single crystals are given in Table I along with the polycrystalline orientations that most nearly correspond. To insure reproducibility, at least three duplicate

Jan 1, 1969

By Byron W. Cheever

In the Journal of the Iron and Steel Institute for 1881 (vol. ii., page 379), will be found an article upon this subject. The analyses there reported mere of samples taken from an ingot made especially rich in impurities and then cast in a sand-mould in order to give the elements a better chance to redistribute themselves, on account of the steel solidifying more slowly than when cast in an iron mould. Wishing to ascertain how much, if any, segregation takes place when the steel is cast in the ordinary way, I placed the subject in the hands of Mr. W. J. Olcott, a graduate of the Michigan University, who has carefully collected and analyzed samples taken from different parts of ingots and billets. In this undertaking he found himself somewhat embarrassed on account of being distant from steel-works, and therefore unable to supervise the selection of samples. He found, however, a competent and willing aid in the person of E. F. Wood, M.E., chemist of the Pittsburgh Bessemer Steel Company, Limited, who has spared no pains in collecting the desired samples and furnishing drawings and descriptions of the ingots from which the samples were taken. The following are the results obtained: Ingot No. 1. This ingot was about 5 feet long and 13 X 131/4 inches at the point of fracture, which was 2 feet from the bottom. The samples

Jan 1, 1885

By W. C. Kerr

WHEN Agassiz and his party of geologists commenced their exploration of the interior of Brazil and the Amazon region, one of the first and, to the last, one of the most novel and striking phenomena which met them everywhere was the great depth of decomposed or partially decayed rock in situ, which mantles, and for the most part conceals, the underlying strata. The same facts strike all geological observers from the North who happen to penetrate the middle and southern latitudes of the Atlantic States. In North Carolina, e. g., the entire middle and western regions, outside of the Quaternary clays, sands, and gravels of the East,-that is, all that portion of the State occupied by the Arch can and Mesozoic rocks,-show everywhere this peculiarity, so new to those accustomed to glaciated surfaces. Not only do the hills and slopes, the mountain chains and

Jan 1, 1880

By E. H. Rennhack, J. F. Libsch

Definite transition behavior was found in unalloyed titanium at 0.13 pct 0 equivalent. The addition of 0.5 Sn, 1.0 Al, 0.5 Al, and 1.0 Sn lowers the tvansition temperature of titanium at oxygen equivalents exceeding 0.22, 0.29, 0.40, and 0.51, respectively. Metallographic evidence indicates that progressive amounts of oxygen restrict deformation at low temperatures resulting eventually in brittle fracture. The presence of tin or aluminum is thought to alter the atomic distribution of oxygen within the titanium lattice in such a manner as to facilitate some degree of slip and twinning. 1 ITANIUM-like iron and zinc experiences a transition from ductile to brittle fracture with decreasing temperature. The presence of sufficient quantities of the interstitial elements, carbon, oxygen, and nitrogen in solid solution, has been shown to progressively lower the room-temperature impact resistance of titanium with increasing interstitial content.1"1 Ogden,et al,2 reported finding no transition from ductile to brittle fracture with decreasing temperature in iodide titanium. However, a definite transition was found to occur at 0.36 pct 0 equivalent in an alloy containing 0.47 pct carbon in solid solution. The oxygen equivalent in this case was obtained by assuming the effects of carbon, oxygen, and nitrogen in combination on the impact properties of titanium to be additive on the same basis as their separate effects on tensile strength, namely: Oe = 2/3 (pct C) + pet 0 + 2 (pet N) They concluded that the tendency toward transition behavior is dependent on the total interstitial content in solid solution and not on any one particular interstitial element. Rennhack,4 however, recently found transition behavior in iodide titanium at an oxygen equivalent of 0.17 pct. Ogden, etal3, reported that the strengthening effects of carbon, oxygen, and nitrogen in titanium decrease with the addition of tin. They showed that tin additions increase the tolerance of titanium for the interstitials, that is, 10 pct Sn permitted individual additions of up to 0.4 wt pct of the interstitial elements without any significant loss in ductility. Aluminum tends to decrease ductility and impact strength of titanium for a given interstitial ~ontent.3 Van Thyne and Kessler5 found that the solid solubility of carbon in titanium doubled in the presence of 10 pct Al. The precise effects of tin and aluminum in the nrespncp of rorvfen nn the impact properties of titanium had previously not been determined. The high oxygen tolerance of titanium containing tin may provide a suitable means for improving the impact properties of titanium containing the interstitial elements, particularly oxygen. Unlike tin, however, aluminum has a high affinity for oxygen and will reduce rutile titanium dioxide (TiO2)by a thermit-type reaction.6 Thus, the atomic distribution of oxygen in titanium might be different in the presence of aluminum. The present work was undertaken to: 1) Determine the effect of oxygen on the transition behavior of unalloyed iodide titanium. 2) Determine the effect of small amounts of tin and aluminum on the transition behavior of iodide titanium in the presence of oxygen and other interstitial~. EXPERIMENTAL Three different lots of iodide titanium were employed to prepare the alloys studied in the present work. Their chemical composition is presented in Table I. The compositions of the tin and aluminum used for alloying are shown in Table 11. Oxygen additions were made using calcined rutile titanium dioxide (TiO2)of 99.7 pct purity. Alloy Preparation—Four titanium-base alloys containing separate additions of 0.5 and 1.0 pct each

Jan 1, 1960

By Thomas M. Dr. Drown

IN experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

By Thomas M. Drown

In experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

By J. Douglas Gibson

In Canada, the economic climate for mining is still warm, but a noticeable chill set in last November when the Government published a White Paper on tax reform known as the Carter Report. Moreover, this chill could drop to a freeze injurious to the whole Canadian economy if two of the proposals in the Carter Report are adopted. The offending suggestions call for an end to (1) the depletion allowance and (2) the three-year tax holiday for new mines. Both of these tax incentives have played a major role in the postwar development of the Canadian economy and will, if undisturbed, play an even more important role in the future. The fact that they have worked and worked well is evident from the record. Fruits of an Industrial Beanstalk Excluding fuels, the value of Canadian mineral production was just under $3 billion in 1968-almost nine times as much as in 1946. With fuels included, the figure is $4.25 billion, or almost ten times as much as in 1946. Proportionately, this growth far exceeds that of Canada's manufacturers or of her economy as a whole. Table I traces the overall mineral production growth by principal products. Of particular interest here are petroleum, iron ore, natural gas, sulfur and potash, the combined production of which has grown from little or nil to a point where it now accounts for more than 40% of Canada's mineral output.

Jan 1, 1970

By Willis Burns

I. INTRODUCTION. These notes are submitted, not as a discussion of the modern practice of electrolytic-copper refining, but as the record of a refinery that was among the pioneers in the field and that is to-day, and has been for 17 years, operating under conditions not to be found in any similar plant in the country. I refer to the current density, which is at least 60 per cent. higher than that regularly employed elsewhere, and to the fact that the anodes treated are the direct product of the converter rather than of the reverberatory furnace. The writer has no knowledge of any other refinery treating anodes of this character.

Jan 8, 1913