Search Documents

Jan 1, 1968

By J. W. Leonard

This expanded and more detailed supplement to earlier published work1 is offered as a means to demonstrate the high empirical correlation which exists between the readily measured coal bench scale test parameters of volatile matter (d & a.f.), Hard-grove grindability index (HGI), Koppers cone bulk density (BD) and pulverization level (% passing a 1/8-in. screen) to the less readily measured full scale coke stability index. Thus, Fig. 1, 2 and 3 represent the correlated test data contained in Tables I, II and III respectively. Ninety-six coals are correlated so that 97% of the resultant cokes fall within two points and 100% fall within three points of the actual tested coke stability indices. The main generalizations which can be drawn from the correlation of these coals are as follows: 1) The coke stability indices for higher bulk density coals (46.0 BD to 50.6 BD) appear to be largely influenced by differing combinations of factors for coals above and below a pivotal point of approximately 36% to 37% volatile matter. Below this pivotal volatile matter coke stability index appears to be influenced largely as a result of changes to the coal volatile matter and pulverization level. While above this pivotal volatile matter coke stability indices appear to be dependent on the coal hardness, as measured by the HGI, and to some extent upon coal volatile matter. Pulverization appears to have little influence on the coke stabilities of the harder coals (52 HGI to 58 HGI) of greater than 36% to 37% volatile matter. 2) The coke stability indices for lower bulk density coals (41 BD to 45.9 BD) appears to be largely influenced by changes to coal volatile matter and pulverization level for softer coals above approximately 58 HGI. 3) The main empirical observation to be drawn from these results is that for coals above approximately 36% to 37% volatile matter the quantities of hard and soft constituents as measured by the HGI are important when defining coal rank for correlation to the coke stability index.

Jan 1, 1965

"Located on Missouri River 16 miles N. E. from Helena, 67 miles from Butte and 18 miles below Canyon Ferry. River drainage area 16,000 sq. miles.DAM: Built in 1907; rebuilt of concrete in 1911. Maximum height 129.3 ft., length over all 720 ft.; elevation of crest 3621; elevation of bridge 3640; normal head 60'; normal tail water elevation 3568.5.SPILLWAY: Length over all 491 ft.; clear opening in 24 sections; 445' flashboards, 14 high to elevation 3635, which is 3.5' above Canyon Ferry normal tail . water elevation.PENSTOCKS: 5 of steel, 12 ft. diam., about 75 ft. long from canal to main turbines, and 3 40-inch diam. from canal to exciters.WHEELS: 5 main pairs, horizontal, center discharge, 48-inch bronze turbines, 225 rev., 4,000 h-p. at 60 ft. head, made by S. Morgan Smith Co., direct coupled to generators, and--3 single, horizontal, 25-inch units, direct coupled to exciters.GENERATORS: 5 W. E. & M. Co. water wheel type, revolving field, 2,800 k-w., 2,400 v., 225 r. p. m., 3 phase, 60 cycle alternators.OPERATION: The plant has a larger water storage than Canyon Ferry and can also use stored water from Canyon Ferry storage. Separate transmission lines 13 miles long connect to lines from Canyon Ferry to Butte, and the Plant operates in parallel with the Canyon Ferry plant."

Jan 1, 1913

By J. L. Weeks, K. F. Smith

IN order to determine the magnitude of thermal conductivity changes resulting from alloying vanadium with titanium and a few other elements, several sam~les were PrePared and measured. The thermal conductivity -values reported herein in Table I were determined with an apparatus previously described.' As in recently reported2 determinations on uranium and uranium alloys, whose thermal conductivities are in the same range as vanadium," the accuracy of the values was checked by using synthetic sapphire." The error in the measurement is estimated to be '-3 pct or 0.003 cal sec-1 cm-l "C-1, whichever is larger. The vanadium used in preparing the samples was the calcium-reduced type and was supplied by the Electro Metallurgical Co. as 99.6+ pct pure. All alloying elements used in the preparations were 99+ pct pure. A nonconsumable tungsten electrode arc furnace was used for melting the alloys and, without opening the furnace, each ingot was re-melted a number of times to insure homogeneity. The samples as prepared by the Armour Research Foundation were machined from as forged material without annealing. Acknowledgment The note is based on work performed under the auspices of the AEC. References 'J. L. Weeks and R. L. Seifert: Apparatus for the Measurement of the Thermal Conductivity of Solids. Review of Scientific Instruments (1953) 24, pp. 1054-1057. 2 J. L. Weeks: Thermal Conductivity of Uranium and Several Uranium Alloys. Trans. AIME (1955) 203, p. 192; Journal of Metals (January 1955). 3C. A. Hampel: Rare Metals Handbook. (1954) p. 593. New York. Reinhold Publishing Corp. Thermal conductivity of vanadium is given as 0.074 cal sec-1 cm- '°C-1 at 100°C. 4 J. L. Weeks and R. L. Seifert: Note Regarding the Thermal Conductivity of Synthetic Sapphire. Journal Amer. Ceramic Soc. (1952) 35, p. 15. At 70°C, K = 0.071 cal sec-l cm-l °C-1.

Jan 1, 1956

By M. C. Fuerstenau

Enrollment in the mineral engineering departments at many of our universities has decreased substantially over the past few years, a fact that is due to a number of reasons. Some of the more obvious reasons are: (l) lack of student stimulation in the classroom, (2) absence or lack of salesmanship by the mineral industry faculty, (3) minimal financial support of academic programs by industry (some companies have been very generous, while others have given nothing), (4) failure of some companies to utilize the engineering backgrounds of personnel, (5) salary in some instances, and (6) job location in some in- stances. As some of these problems have been recognized, appropriate steps have been taken to correct them. Only one of the reasons listed is not subject to change, and that is job location. One university' that found itself in the position of reduced enrollment in the mineral industries is the University of Utah. Since the author was in the Department of Metallurgical Engineering at that university, and since data on enrollment and scholarship support have been published by that department, that department will be used for illustrative purposes to show the effect that active scholarship incentive can have on undergraduate enrollment. As Fig. I shows, there were approximately 35 total undergraduates in the department in 1966. Extrapolation of the freshman line from 1965 to 1966 (and previous years) suggested that no freshmen would be enrolled in metallurgical engineering by 1969 unless something drastic were done to alter the trend. In the Spring of 1966, 20 scholarships were offered to high school seniors as an incentive to enroll in metallurgical engineering. These scholarships were financed from a private endowment to the department, but at the present time industry is also contributing to the program. With these incentives, the department essentially doubled its total enrollment in three years, as shown in Fig. 1. Cornparison of this figure with the number of students on scholarships (Fig. 2) shows a direct correlation between undergraduate enrollment and the number of students on scholarship support.

Jan 1, 1970

By W. L. DeMoulin

A rather detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,I so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to 1/4 in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give-good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this' bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 1/2 by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane. Primary Crushing Plant The primary plant consists of one No. 24 Gates, style K, gyratory crusher, followed by four Gates No. 8, style K, gyratory crushers. All

Jan 1, 1920

Jan 1, 1965

By E. R. MARBLE

THE introduction of a new fuel, such as natural gas, necessitates careful study where it has not been used previously. At the El Paso smelter natural gas required the installation of apparatus with which no one at the plant was familiar, either as to the type of equipment needed or as to the burning of the gas in it. Observation of existing installations of a similar character and assistance from gas engineers served as a basis to determine what was advisable to use. The gas line entering the plant goes to a metering station equipped with a duplicate system of pressure regulators, a temperature recorder and the gas company and smelter orifice meters in tandem. There are three distribution lines that can be inter-connected at a later date, if necessary, to assist in equalizing the plant load. All the larger lines are of heavy

Jan 1, 1930

By Clyde E. Williams

DESPITE the confusion resulting from the depression and the beginnings of recovery, important progress in all branches of iron and steel metallurgy has been accomplished during the year 1933. Research work has been intensive and highly technical, with increasing attention paid to fundamentals. Plant application of research developments has been rapid. Highly specialized laboratory methods were used for the study of iron-ore concentration methods. More attention has been given by the blast-furnace operator to the sizing of ore and the elimination of fines from the charge by the use of sinter. Combustion in the open-hearth has been placed under better control and the insulation of open-hearth furnaces has spread rapidly, with resultant higher fuel efficiency and better control of the melting and refining operations. Control of iron oxide content in the slag and the determination of iron oxide and other inclusions in steel received great attention during the year.

Jan 1, 1934

By D. P. Harris

This paper examines recent developments and work in progress on the application of quantitative methods and computers to the appraisal of the mineral resource potential of discrete areas by employing reconnaissance geological information and general economic relationships. The perspective of this paper might be that of a firm planning a regional exploration program or of a legislative body seeking to choose between several alternative actions on the basis of their impact upon the regional resources. In addition to this general survey and commentary, an example is presented of the use of geostatistical analysis and computer simulation to evaluate the economic mineral resources of the Seward Peninsula of Alaska.

Jan 1, 1969

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

University of Alabama University, Alabama Mining and Metallurgical Society WILLIAM R. HIGGS, President ROBERT E. MEAD, Secretary J. R. CUDWORTH, Faculty Sponsor MILTON H. FIBS, Counselor University of Arizona Tucson, Arizona Miners' Society LEE BLESSING, President R. W. CORY, Secretary E. P. MATHEWSON, Faculty Sponsor B. R. HATCHER, Counselor University of California at Los Angeles Los Angeles, California Student Chapter, A.I.M.E. ARCHER WARNE, President ROBERT JOHNSTON, Secretary E. K. SOPER, Faculty Sponsor EMILE HUGUENIN, Counselor Colorado School of Mines Golden, Colorado Student Chapter, A.I.M.E. J. Ross REED, President ANDREW PERRY, JR., Secretary J. BURNS READ, Faculty Sponsor A. W. NEWBERRY, Counselor

Jan 1, 1936

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

E. E. Olcott, New York City: Prof. Kemp's valuable description of the Lancaster Gap mine is in line with many other able contributions on the origin of mineral deposits that the Institute has lately brought forward. The splendid contribution that Prof.

Jan 1, 1895

By ARCHIBALD DOUGLAS

BY this time almost everyone knows, in a general way, the corporate income distribution policies of the 1936 Revenue Act, and many of the practical problems arising there under. This article is not intended to be a technical discussion of that act by title, subtitle, section, or supplement, nor an analysis of inter- dependent sections of the various acts over many years woven on the fiscal loom f our Congressional machine. Such a discussion would require the spinning of a web of words too long for patience. Yet ,a general statement of the underlying plan of the 1936 Act, so far as it affects dividend policies, is perhaps useful.

Jan 1, 1937

By Ta M. Li

How will phosphate producers in southeastern Idaho fare with growing governmental regulations and environmentalism of the late 1970's? With a similarity that is reminiscent of the battles between the coal industry and environmental-conservation groups earlier in the decade, Idaho's future growth and a nation's need for phosphate fertilizer products remain uncertain. The catalyst that brought the issue to the forefront was the preparation of an Environmental Impact Statement (EIS) addressing the development of phosphate resources in southeastern Idaho. Although the final EIS was published in August 1977, resolution of rational and orderly growth in this potentially vital region remains stifled as Secretary of the Interior Cecil Andrus virtually "sits" on it.

Jan 1, 1978

By Betty J. Laswell, Gerald W. Laswell

The stepped-up pace of US open-pit and surface mining during the 1970's is a direct response by mining firms and equipment manufacturers to rising costs and declining ore grades. In the race for bigger and more efficient machines, rotary drills have emerged as the foremost leader in primary drilling at major US surface operations. At least 12 different manufacturers now offer rotary rigs in the 102- mm-diam. (4-in.) or greater blasthole size range. With capital investment for the larger units quickly approaching $1 million, the question is asked, "What's been the performance record to date of rotary drill rigs operating in North America?" To answer that question, a comprehensive study of rotary blasthole drills was conducted which qualitatively reveals various problem areas inherent in the rotary drill market and indicates some new directions for improvement.

Jan 6, 1978

[ ]

Jan 1, 1938

By AIME AIME

ALL sessions of the Mining Geology Committee at the Annual Meeting this year were held jointly with other groups, a plan that seemed to work out to the satisfaction of every one. Certain of these sessions are reported in this issue by others; the ones held on Wednesday are covered here. Ten papers, as published in the February M&M, were on the program for the Wednesday morning session, held jointly with the Society of Economic Geologists. Mr. Eckel made a brief presentation of his paper, on which there was no discussion, and Mr. Peoples presented that of which he was a joint author. D. M. Fraser then discussed a gravimeter survey for chromite in Cuba, which blocked out some 50,000 tons of ore, and F. G. Wells told of work on chromiferous sands in Oregon.

Jan 1, 1943

By Donald C. Myntti

Modern open-pit mining can be described as a capital-, labor-and energy-intensive, large-scale, mechanized, and highly repetitive bulk material preparation and handling operation, with emphasis on the word "mechanized." In hard rock, this generally means shovels loading blasted materials into haulage units for transport to processing plants, stockpiles, or waste dumps. Mine management deals with several primary concerns on a daily basis; e.g.: Will any serious accidents and labor problems occur today, and will the tonnage targets be met considering the physical condition of the equipment? The latter subject will be discussed from a maintenance perspective. A successful, progressive heavy equipment maintenance program that protects company assets involves many elements. They include: •Proper equipment selection and procurement •Well-trained and motivated workforce •Good shop facilities •Preventive maintenance (PM) program •Warehouse support •Operations-maintenance department cooperation •Meaningful paperwork

Jan 3, 1978