Search Documents

By A. Thielen

In experiments for the production of steel the principal problem has always been the introduction into, or removal from, the iron of a definite quantity of carbon. Although the solution of this problem had engaged a more or less blindly and empirically directed effort for a long time, it was only with the development of analytical chemistry that the rôle which carbon plays in the constitution of steel was disclosed in its full significance, and that many of the problems confronting the steel-maker were thereby more clearly defined than before. For a long time, and to a certain extent even to this day, the percentage of carbon in steel has been the controlling means of deter mining its quality and hardness. In many cases the percentage of carbon alone has been relied on for judging large consignments, such as the large deliveries of wire-billets and blooms to America during the past twenty years; and though to-day the influences of the other constituents are recognized and many other considerations are taken into account, and though, moreover, some special steels, such as the Hadfield manganese steel, apparently dispense to a certain extent with the assistance of the carbon, yet fix our Bessemer, Thomas, Siemens and crucible steel the carbon still remains one of the most important constituents, and I venture to say it is indispensable. In order to produce in the Bessemer converter a steel of a certain required percentage of carbon, two methods, as is well known, present themselves. By the one the decarburization process is stopped when the desired carbon limit in the bath has been reached ; by the other the bath is completely decarburizecl, and then a calculated amount of carbon added in the form of spiegel, ferro manganese, etc. In Germany the latter method only was adopted, and it was retained when the Thomas-Gilchrist process for the production of low-Phosphorus steel from high-phosphorus iron eame into use, since from the nature of the new process complete decarburization is neces-

Jan 1, 1891

By John C. LaScola, David M. Hyman, William P. Diamond

The U.S. Department of the Interior, Bureau of Mines, has established a computer-implemented coalbed methane data base containing data representing over 2,000 coal samples from approximately 250 coalbeds located in 17 States and one Canadian Province. Space for approximately 130 sample characteristics is reserved for each sample record and is divided for access efficiency into three separate physical files. A software package was written to provide a user-friendly environment in which the three files can be manipulated simultaneously. These files can be used interactively in DATATRIEVE 11, a commercially available sorting, retrieval, and report-writing software package or in any FORTRAN-compatible system for statistical analysis. The data base has been established for coalbed methane research in response to the health and safety needs of the mining industry. Possible applications of the data base include mine planning related to the occurrence of gas, as well as delineating areas of resource recovery and utilization.

Jan 1, 1983

By Cornelius F. Kelley

AT the Annual Meeting of the A.1.M.E. last February, Cornelius F. Kelley, chairman of the Anaconda Copper Mining Co., was presented with the Charles F. Rand Memorial Medal for "conspicuous success as administrative head of great enter- prises engaged in the production of nonferrous metals at home and abroad; for inspiring leadership of an organization that has trained able engineers for service wherever ores are mined and metals are recovered; and for enhancing the prestige of metal mining in the financial and industrial world." Mr. Kelley's acceptance speech follows: I am not unmindful of the fact that the distinction is not to be considered a personal one, but that by the language of the citation itself it is rather a recognition of the service that has been performed by the many trained men of an industrial organization that in the arts of mining and metallurgy and in the fabrication of metal products has performed a distinct service to the industry and to mankind. In that spirit, the award is accepted, and on behalf of the organization I represent and myself, I thank you and assure you that the honor is deeply appreciated.

Jan 1, 1944

By T. N. McVay, E. E. Creitz

Rather large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about I. miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and ti-tanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, Opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The x ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fe+2 and Fe+3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1949

By C. A. Heiland

A. INTRODUCTION (C. A. HEILAND) I. PRINCIPLES OF TEMPERATURE COMPENSATION IN MAGNETIC INSTRUMENTS The principle underlying the majority of magnetic intensity variom-eters is a comparison of the force to be measured with another force of known magnitude. The known force may be (a) of a magnetic nature, such as magnetic fields produced by magnets or coils, or (b) of a mechan-ical nature, such as (1) the elastic forces of wires, or (2) the force of gravity, such as employed in bifilar magnetometers and magnetic balances. In instruments of such type, usually a magnetic system is employed, free to move about either a horizontal or vertical axis, on some sort of a suspension. If the earth's magnetic field alone were present, such a system would adjust itself into the direction of the field or that of its components. Owing to the simultaneous action of the comparison force, however, the magnetic needle assumes a position that differs from the direction of the magnetic force; for all such instruments, the angle of deflection a is given by tan a = F/X, where F is the known and X the unknown earth magnetic force component. In other words, the magnetic system merely serves as an "indicator" for the position of balance of the two forces. Considering the matter from this point of view, it is not immediately obvious why the temperature of such a magnetic system should modify the results. In magnetic instruments, we may distinguish two different effects of temperature: (1) a magnetic effect and (2) a mechanical effect. The first is due to the fact that the magnetic moment of a magnet drops with an increase in temperature. This drop is characterized by the temperature coefficient of the magnetic moment µ (see equation 1). The second effect is due to the change in the .torsion of suspension wires with temperature or to the expansion of lever arms of masses acting on magnetic balances.

Jan 1, 1932

IN CHAPTER I it was shown that the approximate market value of the copper produced at the twelve big Porphyry mines from 1905 to 1931, inclusive, was $2,821,300,000. This represented the refined metal ready for shipment to the consumer. In addition, at least $50,000,000 worth of gold and silver had been produced, more than $30,000,000 coming from the Utah mine alone. Consequently, the revenues totaled about $2,871,300,000, as shown in Table 58. Society paid this sum for a given quantity of metal that it wanted for industrial use. Where did the money go? Who were the direct beneficiaries of the creation of this new wealth? These questions this chapter will answer in a general way. Because some necessary data are not available, an exact tabulation in detail can not be made, but Table 58 is believed to reflect with reasonable accuracy the disposition made of the aggregate income from the twelve operations. The word "operations" is used advisedly because the complexity of corporate relations precludes the possibility of picking out companies, as could be done if each enterprise were an independent entity such as Miami, for example. Some explanation of the table and some elaboration of the items under "Outgo" is desirable. In the first place, it is assumed that the sum of surplus current assets existing in various treasuries at the end of 1931 was substantially equivalent to the “new” money that actually was put into the enterprises as a group. Less than $20,000,000 in new capital was realized from securities sold by the Utah Copper Co., the remaining funds coming from earnings. In respect to some of the others, such as Chuquicamata, Inspiration, and Andes, the amount of new money was much greater. However, of the two items-total new capital invested and total current surpluses-the former

Jan 1, 1933

By G. P. Boomslitter

In previous discussions on stresses in hoisting ropes, little has been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured. Theoretical Discussion According to elementary physics, the force required to accelerate a Wf body of weight W at the rate of f ft. per sec.2 is wf . To raise the body Wf with acceleration of f ft. per see.2 the total force required is I + Wf, in if

Jan 1, 1927

By Ralph E. Davis, Lyon F. Terry

The rapid expansion of the natural gas industry in this country during the past three or four years has necessitated the construction of a number of long and comparatively large diameter high-pressure pipe lines This period of expansion and construction is still at high tide, and the current year will doubtless surpass all prior years in mileage and capacity of gas line installation. The fundamental economics of the business of long-distsrier transportation of natural gas may be briefly and simply stated, although most careful consideration must be given the actual determination and integration of the several more important factors which determine the ultimate success or failure of such a project. Reduced to its simplest form, a sound natural gas transportation project requires: 1. A competent source of gas, where the combination of quantity of gas available, cost of production, and longevity meet the given requirements. 2. A market, reasonably certain to endure in the face of any probable competition, of satisfactory size and price, and having a sufficiently favorable load factor. 3. A cost of installation of pipe line systen and an operating cost such as will, with honest and reasonably efficient management, afford a net operating return sufficient to attract the necessary capital required. In a11 new projects of this kind it is necessary that thehe three cssentials to ultimate success be assured. Hence the necessity of competent surveys of gas supply, and of market, both industrial and domestic. The prudent engineer will allow for "factors of safety" in reaching his conclusions just as he would in the design of a bridge. This paper deals primarily with but one of the major considerations enumerated above, I. e, the economic design of the pipe line system. The "pipe line system" will be considered to include (1) the pipe Iine, and (2) a series of compressor plants along the pipe line for maintaining

Jan 1, 1929

By James F. Kemp

Discussion of the paper of D. Foster Hewett, Bulletin To. 27, March, 1909, pp. 291 to 310. JAMES F. KEMP, New York, N. Y.:-Mr. Hewett's paper is one of exceptional interest, because it not only adds an important contribution regarding one of the rarer, valuable elements, but also because it introduces compounds hitherto unknown and in associations no less novel. While we have occasionally dis¬covered and recorded asphaltite in metalliferous deposits, for example in the Joplin and Granby districts, we have not seen a metallic ore in a deposit essentially asphaltite. The source and method of introduction afford a subject well worth serious reflection. Vanadium was first discovered and recognized as a distinct element in the slags obtained in smelting the titaniferous magnetites at Taberg, Sweden. For a long time, therefore, we looked upon the titaniferous magnetites as its hone. Analyses proved, years ago, that it was present in the ores of this type in New Jersey and in the Adirondacks. It was quite rarely determined, but when looked for it was, I think, invariably found, although the Amount seldom exceeded 0.5 per cent. of V,05., In just what combination it exists in the titaniferous ores is uncertain. One might imagine V2O3 replacing some of the Fe2O3 of magnetite; or, since in the lead series vanadates and phosphates are closely akin, one might wonder if a lime-vanadate could take the place of apatite. Yet no lime-vanadate has been found in nature, and apatite itself is usually rare in the titaniferous ores. When percentage-curves are plotted for a series of analyses of the ores, the line of vanadic oxide shows a curious sympathetic behavior with the line of chromic oxide;' but the data are somewhat limited, and no compound has sug¬gested itself which throws light on the matter. Dr. W. F. Hillebrand has discussed the occurrence and dis-

Oct 1, 1909

By H. E. Cline, D. F. Stein

A fine lamellar structure with interlamellar spacings ranging from 0.I to 3.7 was Woduced by high-speed directional solidification and used to study the interaction of dislocations with an array of bimetallic bound-am.es. The tensile flow properties were measured at elevated temperatures and the results interpreted in terms of an image force model. As the width of the plates decreases the strength increases according to a Hall-Petch relation, suggesting pile -ups. Considerable strengthening was also observed at elevated temperatures. In recent years composites containing a strong but brittle phase and a ductile but weak phase have been studied extensively in the search for a high-strength material with adequate ductility.' However, the strength of these composites has been limited to a volumetric average of the strengths of the component phases. In this paper we will show that a composite made by directional solidification of a Cu-Ag eutectic has strength properties that substantially exceed the strength of either of the metals in the composite, and an explanation for this increased strength will be presented. The Cu-Ag eutectic is a near ideal material to study for several reasons. The eutectic structure is made up of alternate plates of silver-rich and copper-rich phases with the same crystal structure.2'3 In addition, the mechanical and elastic properties of silver4 and copper5 are known over a wide range of temperatures and the eutectic microstructure is stable to nearly the melting point.6'7 Therefore, the properties of the eu-tectic are readily comparable to various theories involving the mechanical properties of copper and silver. The experiments consisted of producing directionally solidified Ag-Cu eutectic material, determining the structure and performing tensile tests at different temperatures and strain rates. EXPERIMENTAL A) Solidification and structure. A cylindrical ingot 2.2 cm in diam and 15 cm long was prepared from 99.999 pct pure materials and cast in argon. The ingot was placed in an alumina crucible and was direc-tionally solidified at 7 x 10"4 cm per sec in a Bridg-man apparatus in argon. Metallographic examination at both ends and along the length of the ingot showed a uniform structure that consisted of fine alternate plates of silver- and copper-rich phases. The plates were aligned parallel to the growth direction, as shown in the longitudinal section, Fig. 1, and were in small randomly oriented domains of parallel plates as viewed in a transverse section, Fig. 2. Four smaller ingots 0.175 in. in diam were solidified at speeds of 2Xlo-', 4.4 xlo-', 4.4 x 10-3, and4.4x10-4 cm per sec to produce a range of lamellar spacings. Replica electron micrographs were taken to resolve the individual plates as shown in Fig. 3. The copper-and silver-rich plates in the larger ingot were about

Jan 1, 1970

By Reed W. Hyde

Some information has been published on the sulphur dioxide concentration of gases from D wight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes Over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide notation concentrates mixed with minus 20.mesh oxide ore, the mixture carrying 16,8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily. to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO z might be utilized, a series of runs was made to determine the concentration ofSO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1 2 to 1 in., ('1 4 to 3% in. and (3) 6 to 5% in. The averages of the determinations from each series are platted On the graph (Fig, 1). The vertical scale shows the percentage by volume of SOz (as determined by the Reich method), and the horizontal scale shows the time e~pressed as percentage of the total sintering time. Sintering was considered to be complete when no SOz could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 Content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume usually will drop slightly toward the middle of the period and increase toward the end. However, this made is a reasonable approximation. several interesting features are brought out by these data. In general, the published data on SO 2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SOz in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 234 min. after

Jan 1, 1944

By Noah Fields Drake

This paper is devoted chiefly to the coal-fields of the western part of the province of Chili and the eastern part of the province of Shansi; but the outline of this belt will give some idea of the extension of the coal-fields over northeastern China. This part of China is topographically divided into: (1) the mountainous peninsula of eastern Shantung; (2) the coastal plains, extending W. and SW. from the gulf of Pechili; and (3) the mountains and table-lands N. and W. of the coastal plains. The plains extend N. and W. from the gulf to within from 10 to 25 miles of the Great Wall, while their SW. extension covers western Shantung and reaches W. along the Yellow river almost to the southern boundary of Shansi. A line joining the mapped coal-fields, shown in Fig. 1, almost gives the western boundary of the plains; since these areas lie on the border of the plains—except the Tsê Chou field, which is on the table-land, 20 to 25 miles from that border. The coal-fields which have been mapped and investigated by the author are shown in Fig. 1. The one at and around Tongshan is known as the K'ai-p'ing coal-field; the one W. of Peking has been called the Wang-p'ing coal-basin; the one SW. of Pao-ting and N. of Chêng-ting may be called the Lingshan coal-field; and the one at and around Tsê Chou is known as the Tsê Chou coal-field. I. The K'ai-p'ing Coal-Field. As is shown in Fig. 2, most of this field lies in the coastal plains, and is therefore covered by alluvium and loess, which have buried the older rock-beds, and the more gentle and older topographic outlines, to such an extent that most of the re-

Jan 1, 1902

AlfreD H. Cowles, Cleveland, Ohio (commuaication to the Secretary*):—Mr.Gillette's paper and his deductions seem to me of the very greatest importance, if the validity of his conclusions and figures can be confirmed. His work seems to solve an unfinished problem that I attempted to solve on the same lines about two years ago, at a time when I was preparing a paper' on another subject for the American Electrochemical Society. The following paragraph is quoted from the paper referred to: "I feel convinced that a further study of the heats of combination now known for so many compounds, which merely express in other terms their voltages of disruption, will show us the allowance that must be made as a departure from unity in the case of each element, for the intrinsic charge of its elementary molecule, and thereby render possible the creation of a table of apparent relative atomic capacities for electricity, similar to the table of atomic weights. With the numerals of this table known, thermal reaction or energy-transformations will be read with the same ease that we now read and trace the shifting of mass

Jan 1, 1904

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,' Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970

By D. F. Kaufman, E. D. Levine, L. R. Aronin

ThE primary slip plane in hcp metal crystals can usually be inferred from the c/a ratio. Basal slip is the primary system at room temperature for zinc, cadmium, magnesium, cobalt, and rhenium, all of which have a c/a ratio greater than 1.60. Zirconium and titanium, on the other hand, each with a c/a ratio of 1.59, deform primarily by (1010) [ll20] prismatic slip. The increasing tendency toward prismatic slip in these materials is generally thought to be associated with the increase in atomic density on (10i0) as c/a is reduced. Beryllium, with a c/a ratio of 1.57, would, according to the above scheme, be expected to exhibit prismatic slip. However, in beryllium of commercial purity, the primary deformation mode at room temperature is basal slip.' The ratio of critical shear stress for prismatic to that for basal slip at room temperature is approximately 5:l. The critical shear stress for prismatic slip decreases quite rapidly with increasing temperature, however, and at 500°C the ratio is approximately unity. The apparently anomalous behavior of beryllium has led to speculation that prismatic slip in this material may be restricted by an anisotropic effect of impurities,' and that, if beryllium could be purified to a sufficient extent, prismatic slip might predominate at room temperature. In such a case, the conditions under which basal cleavage can occur would be suppressed, and enhanced low-temperature ductility might result. With the advent of the floating-zone method for purification of beryllium,3 it has become possible to determine experimentally the effects of purification on basal and prismatic slip. Tensile tests were performed at room temperature on single crystals oriented favorably either for basal or prismatic slip. The crystals had been purified to various extents by zone-refining, employing procedures that have been described elsewhere.4 Relative purities of the crystals were estimated by measuring the ratio of electrical resistance at 4.2"K to that at 298°K. Typical values ranged from 0.40 for commercial-purity material to 7.7 X 10"4 for crystals prepared from vacuum-distilled beryllium and subjected to six zone-refining passes. The purity dependence of the critical shear stresses for basal and prismatic slip is shown in Fig. 1. In the purity range studied, the critical shear stress for basal slip is decreased from 1.4 to 0.14 kg per sq mm. The critical shear stress for prismatic slip is decreased from 6.7 to 5.3 kg per sq mm. The decreases in critical shear stress for each deformation mode, therefore, are approximately equivalent. No purification anisotropy is observed. Because of the absolute magnitudes of the critical stresses, the ratio of the critical shear stress for prismatic slip to that for basal slip actually increases from 5:l to 38:l at the highest purity level studied. It is evident, therefore, that basal slip is the primary deformation mode in high-purity beryllium. This fact must be accounted for in any rationalization of the deformation behavior of hcp metals. This work was performed at Nuclear Metals, Inc., under the sponsorship of the U.S. Atomic Energy Commission.

Jan 1, 1964

By Andrew L. Mular, K. K. Humphreys

Introduction Estimates performed on potential future plants must by their very nature be either order-of-magnitude or budget (preliminary) estimates. Of the three types of estimates recognized by the American National Standards Institute (ANSI Standard Z94.2), order-of-magnitude and budget estimates are the least accurate. Order-of-magnitude estimates have an expected accuracy of plus 50 percent to minus 30 percent. In other words, it is anticipated that actual project cost will be no more than 50 percent above the estimate and no less than 30 percent below the estimate. Budget estimates, or preliminary estimates as they are often called, have an expected accuracy of plus 30 percent to minus 15 percent. The reason that greater accuracy cannot be expected in performing estimates on proposed new facilities is simply that insufficient data is generally available to permit performance of a highly accurate estimate. As stated in ANSI Standard Z94.2, a definitive estimate, i.e., an estimate with an expected accuracy of plus 15 percent to minus 5 percent," . . is an estimate prepared from very defined engineering data . . . (including). . .as a minimum, fairly complete plot plans and elevations, piping and instrument diagrams, one line electrical diagrams, equipment data sheets and quotations, structural sketches, soil data and sketches of major foundations, building sketches and a complete set of specifications." In other words, the engineering of the project must be fairly well underway to permit a definitive estimate to be performed. Such is the case only after the construction decision has been made, all potential alternatives evaluated, and major expenditures committed for a particular course of action. This situation is beyond the scope of this chapter. The chapter is directed to comparison of various technological alternatives for which site specific engineering data is not generally available. Accordingly, such comparisons can be made only by utilizing preliminary or order-of-magnitude estimating techniques.

Jan 1, 1982

By Walter R. Hibbard

THE term lineage was first introduced by Buerger1 to denote dendritic branches, grown from a crystal nucleus during solidification from the liquid, with imperfections in alignment of the order of 10-1 [ ] to 10-4 cm. These imperfections are associated with distortions of the dendrites caused by the subsequent solidification of the inter-dendritic filling and are illustrated in Fig 11. Buerger etched zinc single crystals made by the Bridgman2 method to develop this dendritic pattern and show lineage microscopically. Since maximum crystal growth in face-centered cubic metals occurs along the [100] directions,2 lineage would appear in copper as small deviations of dendritic branches from these directions. Elam4 and others5-8 reported etching effects resulting from coring along the cube face traces of various copper alloy crystals. These traces were used by Samans8 to orient single crystals. Williamson9 noted a "lined structure (in alpha brass single crystals) consisting of an ordered arrangement of etch pits" which were probably traces of {100} planes but somewhat uncertain because they were never straight (i.e., apparently lineage). Greninger10 described the distortion and multiplicity of Laue spots in back reflection X ray photograms of copper single crystals showing lineage. The present investigation includes metallographic, X ray and property studies of lineage in large grain and single crystal specimens of copper. PREPARATION OF SPECIMENS Specimens 10 in. long and ½ in. diam of oxygen-free copper (O.F.H.C.) (99.985 pct) were melted vertically in graphite crucibles under an atmosphere of commercial nitrogen purified through a gas train including sulfuric acid, potassium chloride, magnesium chlorate, hot copper chips and phosphorus pentoxide. After a temperature of 1200°C had been maintained for ½ hr, the furnace was turned off and the specimens cooled at a rate of about 150°C an hour. This method of direct solidification was used by Greninger10 to produce single crystals with marked lineage and in this investigation produced a fair yield of single crystal specimens in

Jan 1, 1947

By J. E. Tobey

UNDER war conditions coal immediately assumes a position of highest importance for coal must carry the basic load for industry. The upward trend in production continued through 1941. Bituminous coal production alone about equaled the total output of bituminous and anthracite in 1940. The figures for 1941 approximated 500,000,000 tons for bituminous, and 54,000,000 tons for anthracite, and production of by-product and beehive coke exceeded that of the previous year. The coal industry, under the National Bituminous Coal Act, is going through a period of readjustment, and is beginning to stabilize itself under the statute. The Federal Mine Inspection Nill became law during the year.

Jan 1, 1942

By David Kellogg

THE electrodeposition of iron has been practiced for many years. The earlier work along this line was directed toward the preparation of pure metal, but later applications were the production of thin adherent coatings as used in the electrotyping of Russian banknotes in 1860. A historical discussion of this subject, however, would require too much space and would be inconclusive. Much has been written on the subject but no two experimenters use the same methods or materials. During the war, the British army repair, shops developed a method for building up worn parts of automotive machinery, aero engines, etc., using the cold surfate . bath and low-current density method.1 The method has been used successfully in commercial work for the production of about 6000 repaired parts, therefore experiments along the same lines have since been made at the Westinghouse research laboratory. The apparatus used was essentially that described in the article mentioned except that the current -used for cleaning was obtained from a 3/4-kw. 60-volt, house-lighting generator, direct connected to a 2-h.p., 870-r.p.m., 440-volt, three-phase, type CS induction motor; while the plating current was taken from the storage batteries at any desired voltage. The anodes were made from 0.036 in. (0.9 mm.) Armco iron made into cylinders 5 in. (127 mm.) long by 8 in. (203 mm.) in diameter with a disk of 1/8 -in. (3.17 mm.) micarta, having a 2 in. hole in the center fitted at each end of the cylinder for stirring. The anodes were hung on a wooden rocker frame driven by a wooden connecting I rod directly connected to a small reducing gear, such as is sold by most of the apparatus supply firms; 3 gal. stoneware crocks were used as containers. The solution used by Thomas, 75 gm. of the crystallized ferrous ammonium sulfate per liter, was tried, using the current density recommended by him; namely, 0.33 amp. per sq. dm. Under these conditions the deposit on a ½ -in.

Jan 2, 1922

By Fred C. Bond

MANY grindability tests have been made in the Allis-Chalmers laboratory since the tabulated results were last published.1 The lists of standard ball-mill and standard rod-mill grindability tests are brought up to date in this paper, and considerable new material is added. This includes a tabulation of open-circuit grinding tests, with impact and compression-crushing tests. The standard ball-mill grindability tests (Table I) were made in a standard laboratory ball mill, 12 by 12 in. inside, running at 70 rpm, with a charge of 285 iron balls ranging from 1 1/2 to 3/4 in. in diameter and weighing 20,125 grams. Seven hundred cubic centimeters of minus 6-mesh stage-crushed dry feed was used, and the circulating load was maintained constant at 250 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 28 to 200, and the grindability is the number of net grams of screen undersize produced per revolution. The table includes 479 tests. It has been calculated that the ball mill does 52.3 joules of useful work on the ore per revolution2 with 93 joules input to the mill. The standard rod-mill grindability tests (Table 2) were made in a laboratory tilting rod mill, 12 in. in diameter by 24 in. long inside, with a wave-type lining, running at 46 rpm. The grinding charge consisted of six 1 1/4-in. diameter and two 1 3/4-in. diameter steel rods, all 21 in. long and weighing 33,380 grams. The mill was rotated level for eight revolutions, then tilted up 5° for one revolution, down 5° for one revolution, and returned to level for eight revolutions. It was discharged by tilting downward at 45° for 30 revolutions. Feed consisted of 1250 cc of minus 1/2-in. stone and the circulating load was maintained constant at 100 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 3 to 65, and the rod-mill grindability is the number of net grams of screen undersize produced per revolution. The table includes 105 tests. The impact and compression-crushing tests (Table 3) are given in a table that is an extension of a previous publication3 in which the method of testing was described in detail. Two equal hammers weighing about 30 lb each were arranged to strike simultaneous blows on opposite sides of the test specimen. Broken pieces of rock passing a 3-in. square and retained on a 2-in. square were set up with the smallest dimension between the hammers, and this distance was measured. The height of the hammers was increased slightly before each blow until the specimen broke, and the foot-pounds per inch of thickness was calculated. Ten pieces

Jan 1, 1947