Search Documents

THE strike and dip of bedded formations is readily determined by trigonometry if some marker horizon is intercepted by three holes. If no marker can be identified and if orientation of the cores is unknown, as is the usual case in diamond drilling, the determination still can be made readily by the use of a stereonet if the bearing, inclination, and angle the bedding makes with the core axis is known for each of the three holes. Such determination, valid only if the bedding orientation is fairly uniform within the area drilled, is considered simpler, faster, and more effective than any solution previously published. Method: The steps of this procedure are as follows: 1) Mark north and south poles on tracing paper placed over stereonet.* 2) Plot the three diamond drillholes by drawing a line from the center of the net in the direction of the bearings of the holes. Then rotate the paper until each line, in turn, lies along the equatorial diameter of the net; the end of each line is determined by the inclination of the hole measured in degrees from the periphery toward the center of the net along the equatorial diameter. Fig. 1 illustrates a vertical hole and a hole inclined at —23" due east. 3) With the projection of one diamond drillhole along the equatorial diameter, measure from the end of the hole, to the east and then to the west, a dis- tance in degrees equal to the core axis-bedding plane angle. Find two more points by measuring the same number of degrees north then south along the great circle from the end of the drillhole. Draw a circle, the center somewhere along the direction of the projection of the drillhole, to connect these four points. Draw circles for the other two diamond drillholes in the same manner. See Fig. 1 for two circles representing core axis-bedding plane angles of 35" and 23" and Fig. 2 for these plus a third circle representing a core axis-bedding angle of 42" in a hole bearing S 50 W inclined at —52". 4) Rotate the tracing paper until one great circle on the stereonet is found which is tangent to all three of the circles or parts of circles derived in the previous step. Trace this great circle on the paper and join its ends with a straight line passing through the center of the net. The bearing of this line is the strike of the bedding. In Fig. 2 the bedding strikes N 77 E. 5) Rotate the paper until the strike is along the polar diameter of the net. The dip of the bedding is determined by measuring along the equatorial diameter the distance in degrees from the periphery of the net to the great circle derived in step 4. The dip of plane illustrated in Fig. 2 is 55" to the N 13 W. Fig. 3 indicates the solution for three holes whose bearings and inclinations are N 20 W and —43o, due E and —30°, S 30 W and 23" with core axis-bedding angles of 30°, 50°, and 43" respectively. The bedding (stippled area) strikes N 44 W and dips 70" to the southwest.

Jan 1, 1956

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By J. Jones-Parra, R. S. Reytor

The porosities of fractured limestone reservoirs can be divided into two broad types in accordance with their effects on fluid distribution and fluid flow. In the coarse porosity, gravity segregation lakes place freely and the resistance to fluid flow is very small. In the fine porosity there is no segregation and a high resistance to flow, and it has relative permeability characteristics similar to tight sandstones. By analyzing the affect of the two porosities it is concluded that in some cases to recover the maximum amount of oil it is necessary to remove large quantities of gas from the reservoir by producing at high gas-oil ratios. In this manner the fine porosity is drained of its oil and the gas-oil contact drops slowly permitting higher production rates from the oil leg. Since this conclusion is contrary to widely accepted principles of conservation, a mathematical model (Fig. I) was constructed to duplicate the conditions desired. The behavior of the model indicates that under certain conditions it is possible to recover more oil by producing at high gas-oil ratios than by production at low gas-oil ratios, and that the rate of production is affected more by gas shut-offs than by the decrease in pressure (Figs. 2, 3, 4 and 5). INTRODUCTION It has been noted that certain limestone reservoirs behave in such a way as to indicate that there are two distinct types of porous spaces available for fluid storage and fluid flow. Regardless of the nature of these porous spaces the distinguishing characteristic is that in one type of porous space there is definite gravity segregation between the oil and the gas; while in the other, the gas evolved tends to remain distributed equally throughout the reservoir. For the sake of simplicity the porosity in which gravity segregation takes place at a fast enough rate to affect the behavior will be called "coarse po- rosity", while that in which this is not so will be termed "fine porosity". The behavior of a reservoir of this type would be different than that of a sandstone reservoir, especially if most of the oil is in the fine porosity. It has been observed that fluid flow to the wells takes place mostly through the coarse porosity. The large fractures which

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By K. S. Seljesater

SINCE the development of dispersion-hardenable lead-antimony alloys1 in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. EXPERIMENTAL In order to-study the effect ,of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per FIG. 1..-CHANGE OF MICRO-BRINELL HARDNESS WITH TIME OF 1 PER CENT. LEAD-ANTIMONY ALLOY. cent. lead). The alloys were cast into bars 1 ½ in. wide by ¾ in. thick and cold-rolled to about 1/8 in. thickness. Three samples of each composition were annealed 1 hr. at 225° C. and quenched in water. One set was aged at room temperature, one at 50° C., and the third at 100° C., the

Jan 1, 1929

By H. P. Willard, R. W. Gates

Basic Inc., has been mining magnesite and brucite for 27 years at Gabbs, Nev. This is a medium sized open-pit mine. The magnesite deposits are in north-western Nye County about 30 miles east of Luning, Nev., on the west slope of the Paradise Range, at an elevation between 5000 and 6000 ft. The magnesite and associated brucite is used to make magnesia refractories employed principally in the steel industry and magnesium oxide for various chemical uses.

Jan 10, 1963

By AIME AIME

MOST recently elected to the limited group of Honorary Members in the A.I.M.E. is the distinguished Australian metallurgist, Guillaume Daniel Delprat. His citation reads: "in recognition of his distinguished achievement as metallurgist, engineer, and administrator in the production of ferrous and nonferrous metals," Mr. Delprat's ability and experience in both the ferrous and nonferrous fields at once distinguishes him from most of his professional brothers. Mr. Delprat's nativity was neither Australian nor English, for he was born in Delft, Holland, in 1856, and educated in Amsterdam. At the age of 22 he went to Spain, as metallurgist for the Tharsis Sulphur and Copper Co., Ltd. Afterwards he spent some time with the Bede Metal and Chemical Co., which had mines in both Spain and Norway, and of which company he became general manager. Other positions of responsibility held by Mr. Delprat before he went to Australia included the managing directorship of the Cordova Exploration Co., with properties in Spain and Canada; of the Rincon Silver-Lead Mining Co., in Spain; and of the Deloro Gold Mines, in Canada.

Jan 1, 1936

By David B. Burrows, Francis R. Conley

INTRODUCTION A prerequisite to the evaluation and management of oil properties is accurate information derived from the analysis of core samples; but reliable data, such as porosity and permeability, can result only if all oil and water have been removed from the core samples analyzed. The most common method of core cleaning used to date has been Soxhlet extraction—a somewhat static technique, which depends upon the slow diffusion of hot solvent through the core sample. Soxhlet extraction performs satisfactorily only with highly permeable samples and at best requires long cleaning periods. The centrifuge method was developed in 1951 by Continental Oil Co. to overcome the inefficiencies inherent in the Soxhlet method. The new method is basically an operation in which hot solvents are caused to flow through the samples under the influence of centrifugal force. The centrifuge unit has proved so successful that samples which formerly required days for partial extraction can now be completely cleaned in approximately one hour. The original idea was conceived in 1950 by Elmer S. Messer, whose early experiments consisted of flowing solvent over sandstone samples suspended in a revolving basket and driven by a vertically mounted vacuum cleaner motor. Results were so outstanding that more permanent units were constructed. A modified model using this basic design was recently built by Core Laboratories, Inc., and is now used regularly in their operations. DESIGN Fig. 1 shows a photograph of the two extractors routinely used to clean small core plugs in the Production Research Div. of Continental Oil Co.'s Ponca City laboratories. For illustrative purposes, the basket from one of the units has been removed, and because both extrac- tors are of identical design only one is described in the following discussion. Each extractor unit consists of a centrifuge and a solvent still. The core basket of the centrifuge is made of mild cold rolled steel 7 1/2 in. in diameter and 1 1/8 in. deep. The basket holds 18 1-in. samples (cubical or cylindrical) and is attached directly to a cone fitted to the shaft of the motor. Both the outer rim and the hollow hub of the basket contain perforations for the passage of solvent and extract. The solvent is delivered to the perforations by means of a copper tube inserted into the hollow hub. The motor is a vertical tool post grinder motor; (115 v, 5.6 amp, 0-60 cycles, AC-DC, rated at 1/3 hp). It has a rated speed of 10,000 rpm under full load and 15,000 rpm with no load. Variation of speed is obtained by the use of a variable transformer. The solvent still was constructed from one end of a stainless steel oxygen bottle by inserting a heating element, sight glass, and piping as shown on the schematic diagram, Fig. 2. The heater used was a three-position, 1,000 w, 115-v, immersion type. Intermittent flow of solvent to the centrifuge is obtained by means of a siphon bottle inserted between the condenser and the centrifuge.

Jan 1, 1957

By Waldemar Lindgren

I. Character of the Deposits, 226: Principal Features, 226 (Form, 227; Posi tion, 227 ; Constituent Minerals, 227 ; Exceptions, 228) ; Literature, 228 ; Geo graphic Distribution, 230 ; (California, 230 ; Idaho, 231 ; Arizona, 233 ; British Columbia, 233; Northwest Territory, 234 ; Mexico, 234; Other Countries, 235). 11. Origin oF the Deposits, 236 : Contact-Metamorphism, 236; Caw of Contact Metamorphism, 237 ; Similar Deposits of Different Origin, 240; Genetic Classifi cation, 240 ; Relation of Pegmatite- Veins to Ore-Deposits, 242. I.—Character of the Deposits. 1. Principal Features. In many schemes of classification and description the term contact-deposit has been somewhat loosely applied to all accumu-

Jan 1, 1902

Shoemaker: We've all heard a lot about epoxy liner backings. This brings up the question-do zinc furnaces still have a place in a new plant? Meaders: I would, you must understand, be prejudiced in this question because we introduced epoxy backing into the industry. Naturally, we wouldn't have done so if we didn't think it should be done. With that background maybe I could give a little more information on this particular subject than some of the others, because we now have been in this business for some three or four years.

Jan 11, 1967

Merritt: Karl, you are a native New Englander, having been born in St. Albans, Vermont, in 1885. How did you decide on becoming a mining engineer? Twitchell: While I was attending St. Albans High School, my uncle, who had been the American Consul in Kingston, Ontario, for many years, told me of the excellent mining school there. He also introduced me to a Canadian mining engineer who sparked my interest in mining by noting the possibility of achieving personal success without always being under salary. Well, that appealed to me, so I applied to the Kingston School of Mines at Queen's University.

Jan 9, 1965

By Arthur Lubinski, K. A. Blenkarn

It is explained why the bottom portion of freely suspended tubing in a pumping well buckles and straightens in succession during the pumping cycle. Field evidence of resulting rod-on-tubing wear, excessive polished rod load, and excessive horsepower are given. The possibility that buckling hastens pump wear is strongly suggested. Means for either prevention of buckling or for mini-mizing its effects are explained, their relative merits compared, and field results of their use given. These means are: tension anchors, tail pipe, sucker rod guides, and corrosion inhibitors. Charts and formulas for best use of tension anchors, tail pipe, and guides are given. Use of tension anchors, or compression anchors with a heavy tail pipe, prevents both buckling and breathing, thus improving volumetric efficiency. Without tail pipe, buckling above compression anchors precludes such improvement. INTRODUCTION It is well known that a column must be subjected to some compression in order to buckle; and also that a structural member does not buckle if subjected to a tension. When consideration is given to a tubular column, the question may be asked, "How is the buckling phenomenon affected by inside or outside pressure?' At first, it seemingly should not be affected. However, this is not so. In order to arrive at a correct deduction one should first understand the basic reasons for buckling of a column under loading*. Then he should add to the effect of that loading the effect of pressure. Following this procedure, one may discover quite unexpected phenomena. In some cases, when subjected to more pressure inside than outside, a pipe may buckle under tension. In other cases, a pipe may remain straight, although subjected to a very large compression. In 1950 and 1951 it was explained why the bottom portion of a string of pipe freely suspended in a well does not buckle even when subjected to a large compression due to buoy- ancy.2,3 It was shown that the com-monly used concept of a neutral point, as being a point in the string with neither compression nor tension, is inadequate, and a more relevant definition of the neutral point was introduced. The findings were also generalized to cases of different pressures inside and outside a pipe.3a Later, in a further generalization, allowance was made for variations of stress and pressure with depth.' The findings were applied to the new technique of hydrostatic high pressure testing of lengths of pipe in the mill.5 In 1952 it was observed that previous theoretical findings apply to tubing in pumping wells. The lower part of freely suspended tubing buckles during the upstroke portion of the pumping cycle. Later, it was ascertained that this phenomenon is responsible for wear and malfunctioning of the equipment. Various remedial measures were devised and successful field trials conducted. Only brief mentions on the subject have been published.6,7 In this paper, the phenomenon of tubing buckling is explained, field

Jan 1, 1958

By Edward B. Durham

At the Richmond mecting in February, 1901, I presented for discussion the proposed rail-specifications of Committee No. 1 of the American Section of the International Association for Testing Materials, with a review of their work, and other matters relating to the heat-treatment and chemical composition of steel (Trans., xxxi., 455). In order to bring out the views of our members on the important points referred to, I offered for discussion the following questions and comments (trans., xxxi., 972): " 1. The advantages to be gained by using more metal in the flanges and web of the heavier sections of rails.

Jan 1, 1903

PASSING over the derivation of the word as well as the description of the alum that has been written of as a liquid and that was once called natta, I tell you that the alum that is commonly called rock alum today is a congealed earthy substance, clear and transparent, of a hot and dry nature, and of a bitter taste with a certain unctuous saltiness. It has an astringent and corrosive property and is drawn from mineral stones by means of art. All that I have seen is of the same nature but of two colors,

Jan 1, 1942

By Keats, J. L.

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical charac- teristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained.

Jan 1, 1957

By George Hale

(The following extracts from Mr. Hale's paper have been made by the Editor, as being of particular interest to our members.) In an address delivered on May 28, at the kind invitation of the Engineering Foundation, I briefly sketched "The War Activities of the National Research Council. "' The wide scope of my subject forced me to touch very lightly upon engineering; I therefore beg permission to return to this phase of the subject. As shown in my earlier address, the' charter membership of the National Academy of Sciences, organized in the midst of the Civil War,

Jan 10, 1918

G. B. WATERHOUSE,* Buffalo, N. -Y. (written discussion?).-One of the most essential features of rail manufacture is the production of rails that will give good service and be free from failures. To this end rails are made to careful specifications and their manufacture is controlled by rigid inspection on the part of both the producing mill and the railroad or its representative, such as the Hunt special inspection referred to in the paper. Captain Hunt refers to the crescent-shape base failures and describes them as ruptures in the rail flanges extending from the outside inward toward the web. This is hardly correct and may be misleading. It has been shown, over and over again, that the base breaks originating in seams invariably start at the center of the rail base; and run longitudi-nally in varying lengths from 3 to 12 in. and sometimes longer. Most of them are from 5 to 8 in. long and then curve outward to the edge of the flange. The split at the center of the base may exist for an indefinite time and not be discovered until the break shows on top of the flange or the piece of flange breaks off. The. stresses that cause the break are explained in two ways: (1) by the eccentric bearing of the rail base, that is taking contact at one side or edge and bringing excessive strain at the center of the base which starts fracture in any seam that may he present at that point; (2) the split may be due to cross strain in the base where this member is thrown into. compression, as happens where a pair of trucks are on opposite sides of the cross tie or rail-base hearing, and the head is put in tension. A careful study of "split base breaks" shows that fully 95 per cent. occur on the tie bearing, which is further evidence that the above de-scribed causes for the initial break are probably correct. These split base breaks are almost invariably progressive, but always start at the center of the rail-base running longitudinally.

Jan 12, 1919

By J. Blodget Britton

To the question, "Do the Pennsylvania anthracites contain phosphorus ?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Iron-masters' Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows

Jan 1, 1873

By Earl Oliver

CONTENTS PAGE A.I.M.E. Stabilization Committee Activity 3 Definition of Capture Rule: Robert E. Hardwicke 4 Westmoreland Natural Gas Co. vs. DeWitt 5 Kelly vs. Ohio Oil Co 5 Bernard vs. Monongahela Gas Co 6 Definition of Ownership in Place 7 Prospective Stabilization Remedies 7 Dean Roscoe Pound's Four Tests of Practicability 7 I: Mechanically Feasible 8 Capture Rule 8 Ownership in Place 10 Mechanical Separation Method 10 Engineering Appraisal Method. 11 II. Economically Advisable. ., . 13 Capture Rule 14 Ownership in Place 14 III. Politically Wise 14 Capture Rule 14 Ownership in Place 17 IV. Legally Sound 18 Capture Rule 18 Ownership in Place 19 Dean Henry M. Bates' Analysis 19 Resume 22 THE A.I.M.E. Stabilization Committee was named in 1932 to ascer-tain whether some practical substitute could be devised for the Rule of Capture, which was generally credited with being the major cause of instability in the Petroleum Industry. After considerable intercommittee correspondence a letter was received from. E. DeGolyer under date of Jan. 25, 1935, in which he discussed the possibility of modifying rather than discarding the Rule of Capture. He summarized his proposal as follows:

Jan 1, 1937

By Earl Oliver

Page A.I.M.E. Stabilization Committee Activity................. 133 Definition of Capture Rule: Robert E. Hardwicke.......................... 134 Westmoreland Natural Gas Co. vs. DeWitt................ 135 Kelly vs. Ohio Oil Co......................... 135 Bernard vs. Monongahela Gas Co.................... 136 Definition of Ownership in Place..................... 137 Prospective Stabilization Remedies.................... 137 Dean Roscoe Pound's Four Teats of Practicability.............. 137 I. Mechanically Feasible....................... 138 Capture Rule.......................... 138 Ownership in Place....................... 140 Mechanical Separatio.7 Method................. 140 Engineering Appraisal Method................. 141 II. Economically Advisable...................... 143 Capture Rule.......................... 144 Ownership in Place....................... 144 III. Politically Wise.......................... 144 Capture Rule..........................144 Ownership in Place.......................147 IV. Legally Sound..........................148 Capture Rule..........................148 Ownership in Place.......................149 Dean Henry M. Bates' Analysis......................149 Raumé................................152 The A.I.M.E. Stabilization Committee was named in 1932 to ascertain whether some practical substitute could be devised for the Rule of Capture, which was generally credited with being the major cause of instability in the Petroleum Industry. After considerable intercommittee correspondence a letter was received from E. DeGolyer under date of Jan. 25. 1935. in which he discussed the possibility of modifying rather than discarding the Rule of Capture. He summarized his proposal as follows:

Jan 1, 1937