Search Documents

By Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wil-barger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1940 The encouraging outcome of exploration and development in Montague and Cooke Counties and generally greater activity throughout the district resulted in the drilling of some 1700 wells during 1940, about 350 more wells than were drilled in 1939. Approximately 1250 of these tests were completed as oil wells. Production likewise increased during I940 to the extent of 8 million barrels more than the 25 1/2 million barrels produced in 1939. In spite of this large increase in production, known oil reserves again increased substantially. As is usually characteristic of this district, the new reserves were from a large number of fields, none of which were of such magnitude as to be important to the oil industry. Nevertheless, the Fargo field, Wilbarger County, deserves mention as one of the more important discoveries in this district during 1940. Following seismic surveys, the hmerada Petroleum Corporation located its No. I Goodpasture in sec. 35, block IS, H. and T. C. R. R. Co. survey, and drilled it to a total depth of 6717 ft. This well was completed in July 1940 through perforations in the casing from a pay between 3230 and 3252 ft. for an initial production of 241.5 bbl. on an 8-hr. pumping test. Other potential producing horizons were found in the Pennsyl-vanian at depths of 3960 to 3995 ft., 4208 to 11.234 ft., 4407 to 4422 ft., and in the Ordovician at 6300 ft. Wells completed to date in the several Pennsylvanian horizons have an average daily potential of 600 bbl. of oil. Although no wells have yet been completed in the Ellenburger dolomite (Ordovician), the discovery well swabbed I5 bbl. per hour from this formation before plugging back for completion in an upper horizon.

Jan 1, 1941

By Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wil-barger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1940 The encouraging outcome of exploration and development in Montague and Cooke Counties and generally greater activity throughout the district resulted in the drilling of some 1700 wells during 1940, about 350 more wells than were drilled in 1939. Approximately 1250 of these tests were completed as oil wells. Production likewise increased during I940 to the extent of 8 million barrels more than the 25 1/2 million barrels produced in 1939. In spite of this large increase in production, known oil reserves again increased substantially. As is usually characteristic of this district, the new reserves were from a large number of fields, none of which were of such magnitude as to be important to the oil industry. Nevertheless, the Fargo field, Wilbarger County, deserves mention as one of the more important discoveries in this district during 1940. Following seismic surveys, the hmerada Petroleum Corporation located its No. I Goodpasture in sec. 35, block IS, H. and T. C. R. R. Co. survey, and drilled it to a total depth of 6717 ft. This well was completed in July 1940 through perforations in the casing from a pay between 3230 and 3252 ft. for an initial production of 241.5 bbl. on an 8-hr. pumping test. Other potential producing horizons were found in the Pennsyl-vanian at depths of 3960 to 3995 ft., 4208 to 11.234 ft., 4407 to 4422 ft., and in the Ordovician at 6300 ft. Wells completed to date in the several Pennsylvanian horizons have an average daily potential of 600 bbl. of oil. Although no wells have yet been completed in the Ellenburger dolomite (Ordovician), the discovery well swabbed I5 bbl. per hour from this formation before plugging back for completion in an upper horizon.

Jan 1, 1941

By C. J. Bauer

WHEN the pipe lines from the Middle East to the Mediterranean are completed, the Middle East supplies will relieve the strain on Western Hemisphere petroleum resources, part of which are now shipped for Eastern Hemisphere use. A sketch of the world petroleum situation as it appears today and in the immediate future will help in understanding the future place of Middle East oil supplies. Anticipated 1951 world demand is slightly under four billion barrels. To meet this requirement, crude output and refinery runs throughout the world (including Russia) must be increased about two million barrels per day above the average of 1947. This increment, together with pipe lines, tankers, and other facilities, will require in excess of ten billion dollars of new capital in the next four years. We are, therefore, looking forward to the greatest expansion program in the history of the industry.

Jan 1, 1948

Discussion of the paper of K. Huessener, (Trans., vol. 53, pp. 402 to 4333, and of the papers of Linn Bradley, H. D. EGbert and W. W. Strong, pp. 303, 319. R. J. WysoR, So. Bethlehem, Pa. (communication to the Secretary*). —At our plant (Bethlehem Steel Co.), we have had several Bradshaw burners under course of construction and erection for some time, but up to the present we have not had opportunity to put them in service. I regret that I can not take part in the discussion with some actual results from these burners. Mr. Huessener properly emphasizes the importance of obtaining the highest combustion temperature practicable in boiler practice, which demands a near approach to perfect combustion conditions. The ideal burner is the one which, while meeting the various mechanical requirements, fulfills the above condition under a wide range of gas pressure. The question as to the relative value of hot raw gas and cold washed gas for boiler use is a very interesting one. I think that in the past the importance of low temperature of washed gas sometimes has been overemphasized. Mr. Huessener has pointed out that so far as temperature is concerned, no advantage accrues in washing gas below 100" F. In many plants, there is a notable operating economy in using furnace cooling water, which is appreciably warmer than the supply water. However, in a given type of washer, other conditions being constant, the lower the exit gas temperature the lower will be the dust content; this is equivalent to saying that the more washing water is used, other conditions being constant, the lower will be the dust content of the exit gas. For each type of washer there is a certain desired average temperature difference between inlet water and exit gas, concomitant with known average dust and moisture contents, and with economical operation. With the present tendency toward smaller stove checkers, it is generally agreed that gas for stove use should be cleaned to a dust content of 0.20 grain or less. The method employed and extent of gas cleaning are clearly problems for individual furnace plants. As a general proposition, wet washing is decidedly more attractive for furnaces smelting soft, fine Lake ores than for those reducing chiefly hard, lumpy ores, such as the foreign and domestic magnetites. In the former case the average moisture content of the gas is probably 35 grains per cubic foot, the dust content is relatively high and the top temperature relatively low. In our plant, the ore mixtures consist almost exclusively of hard magnetites. The average dust content of the gas leaving the dust catcher will average only about 2 grains and the moisture about 12 grains per cubic foot, corresponding to saturation at about 83" F. The temperature is fully 100" F. higher

Jan 1, 1917

By J. M. Dahl, R. J. Warrick, O. K. Riegger, H. Van Vlack

A liquid which is rich in oxygen (and silicon) develops at steel rolling temperatures in resulfurized and plain-carbon steels. This liquid fluxes solid manganese sulfide. The composition of the liquid and the resulting microstructures vary with the manganese/silicon/oxygen ratios in the steel. The observations and conclusions zuhich are presented are used 1) to suggest a mechanism for MnS deformation in resulfurized steels, and 2) to rationulize hot-shortness anomalies between plain-carbon and resulfurized steels. 1 HIS is a summary of the dependence of sulfide inclusion microstructures upon steel composition, and an interpretation of the behavior of sulfide inclusions at steel-rolling temperatures. Sulfide inclusions are known to have several metallurgical effects upon steel. Their effects upon hot-shortness are best appreciated. Although hot-shortness is well known, it is questionable whether its mechanism is fully understood because there are several anomalies in our interpretation. For example, why should not high sulfur contents produce extensive hot-shortness in free-machining steels ? A second metallurgical consequence of sulfide inclusions appears because sulfide inclusions improve machinability. Furthermore, globular inclu- sions are to be desired over elongated inclusions. To date, we know that lower silicon contents (< 0.010 pct) favor the globular sulfides, but we do not know why this interrelationship between silicon content and inclusion shape exists. Finally, the evidence is strong that the surface quality of a hot-rolled steel is particularly sensitive to the sulfur content. SUMMARY OF PREVIOUS WORK The role of sulfur in hot-shortness was first suggested during the past century. It is uncertain who was the first to conclude that sulfur was less deleterious in the presence of manganese, and that manganese altered the sulfide phase from a liquid FeS to a solid MnS at steel-rolling temperatures. However, Urban and chipman&apos; emphasized that liquid FeS may accumulate as an interdendritic film during solidification. More recently, Keh and Van lack&apos; showed that the intergranular liquid does not completely surround the metal grains at all rolling temperatures. Rather, a small finite dihedral angle exists when geometric equilibration is attained at

Jan 1, 1962

By Robert W. Hunt

At the Atlanta Meeting of the Institute, October, 1895, I had the honor of presenting a paper on " Specifications for Steel Rails of Heavy Sections Manufactured West of the Alleghenies,"* in which, reasoning from the experience of Western railroads with the heavier-sectioned steel rails, I called atten-

Jan 1, 1898

By Frank Clemens Smith

The occurrence of the tellurides of gold and silver, even in small quantities, is so rare that their metallurgical treatment has engaged little attention. A residence of several months at one of the few mines in North America the product of which consists entirely of such ore, has led me to arrange a method for its economical treatment. The mine referred to is the Huronian, situated a few miles distant from Jackfish Lake, in Ontario, Canada. The plan proposed is for this peculiar case, and is put on record as possibly suggestive and helpful .in any similar instance, should it occur. Since freight-rates from the mine to the nearest railroad-point were extremely high, and for other economical reasons, the method proposed is modified by the use, as far as possible, of the machinery already at the mine, and is so arranged that bullion instead of concentrates would be obtained as a final product. The ore-vein at the Huronian mine varied in width from about 4 feet at the surface to 2 feet and less at the lowest level—125 feet —and dipped southeast about 88. The rock consisted, on both foot- and hanging-walls, of soft, green Huronian slates carrying much highly crystalline but barren pyrite. The ore carried an inconsiderable amount of galena with iron and copper pyrites, argentite, hessite, sylvanite (or petzite), and probably altaite, the telluride of lead. Near the surface the ore showed considerable native gold, but this disappeared with greater depth. Two complete analyses of minerals containing tellurium are here attached, as they establish the presence of two important compounds: I. Analysis of a mineral supposed at the mine to be sylvanite, but agreeing more closely in composition with petzite (Ag, Au)2 Te: Ag = 41.062 Au =23.691 Te =32.007 Pb = 0.071 SiO2= 0.097 Fe = trace 96.928

Jan 1, 1890

By J. S. Marsh

AN incomplete statistical analysis performed wearily on the morning after Thursday, Feb. 12, indicates that the unavoidable items of conversation among steelmen were the current shortage of sleeping time and the "Normandie." No analysis is needed, however, to be certain that many thousands of valuable words were uttered, both in and out of technical sessions, concerning matters of deep interest to members of the Iron and Steel Division. The opening session consisted mostly of papers that have appeared, or will appear shortly, in Metals Technology. One, however, that was not finished in time to be printed in any form, but that aroused great interest, was by E. L. Ramsey and L. G. Graper (Wisconsin Steel Works). Its subject was the production of high-sulphur steel by treatment with sulphur dioxide derived from anhydrous sodium sulphite or bisulphite added to the ladle or to the mold. The sulphide distribution in the finished steel is such that increased machinability and longer tool life result. Both items are of obvious importance in these days of mighty production.

Jan 1, 1942

By J. A. B. Forster

The operations of the Electrolytic Zinc Co. of Australasia Ltd. involve the preliminary roasting of zinc concentrate from Broken Hill, New South wales, at a number of acid-making centers on the Australian mainland. The partially roasted material is shipped to the Tasmanian plant where it was formerly re-roasted prior to leaching,&apos; but this practice was gradually abandoned in favor of the flotation of leach residue for the recovery of a concentrate containing about 22 pct sulphide sulphur and known as secontlary or Risdon concentrate.2 This change, together with increased zinc production, called for new furnaces at Risdon for the roasting of 10-50 tonst of secondary concentrcite and 90 tons of new concentrate per day. The war situation made it imperative that construction be commenced without delay and to save time it was decided to base the design on that of Skinner type furnaces which had been built in South Australia twenty years earlier. This involved some sacrifice of desirable features but did not prevent the incorporation of provisions which had enabled small Herreshoff type furnaces to roast secondary concentrate autogenously. The roasting rate in existing furnaces was 10-12 Ib sulphide sulphur per sq ft of hearth area per day, and eleven hearths, 20 ft in diam, were provided in the two new furnaces in anticipation that they would prove capable of the autogenous roasting of 130-140 tons of concentrate per day from 28-29 pct sulphur down to 4.5-5 pct, with an oxidation rate of 11-11.5 lh S/S per sq ft of hearth area per day. It was soon realized, when the first of the furnaces went into operation, that a much better performance than this might be given, and the purpose of this paper is to show how a treatment rate of 100 tons per furnace day, and oxidation rates approaching 15 lb S/S per sq ft per day have been reached. Furnace Design General specifications for the design were based on the results of experience with several other types of furnace and on the special operating conditions

Jan 1, 1950

By A. B. Stevens, C. J. Coberly

The absolute porosity of a rock or sand may be defined as the volume of the interparticle space expressed as a percentage of the total rock volume. The effective porosity as contrasted with the absolute porosity is the volume of the interparticle spaces which intercommunicate with passages of sufficient size to permit the entrance or recovery of gas or oil, also expressed as a percentage of the total rock volume. A knowledge of effective porosity is of prime importance in estimating the ultimate recovery to be expected from oil and gas-bearing formations. The determination of the effective porosity of a rock includes the measurement of two values: (I) the volume of the rock as a whole, and (2) the volume of the grains and sealed pore space. This paper deals with a new apparatus which has been called a "hydrogen porosimeter" for determining the volume of the grains and the sealed pore space. This volume is determined by means of the pressure relations established in the instrument by the introduction of a known quantity of hydrogen. The Hydrogen Porosimeter The apparatus used in this work consists of an upper chamber for measuring the gas, a lower chamber for holding the sample to be tested, a gage for measuring the pressures, a tank of hydrogen, and the necessary connections. (Figs. 1 and 2.) Of the several gases that might be used for this work, hydrogen has been chosen for three reasons: (1) it deviates less from the gas laws than most gases; (2) it readily penetrates the sample; (3) it is absorbed less than most gases by the solids and liquids with which it may come in contact. Method of Operation After placing the sample to be tested in the lower chamber, the apparatus is thoroughly flushed with hydrogen to remove all air from the system, which is then brought to atmospheric pressure Po. The valve connecting the two chambers is next closed and the pressure in the upper chamber is brought up to a pressure PI by admitting gas from the tank.

Jan 1, 1933

By John V. Beall

Cutting costs and increasing safety with new ideas is the byword with The Cleveland-Cliffs Iron Co. on the Marquette Range in Michigan. Among the new ideas being tried out are mechanical shaft mucking, prefabricated lagging to replace timber poles, Carset bits in shaft sinking, and rubber tired guide wheels on the ore skips. Plans are being made to stockpile ore with conveyor belts during the winter. In sinking the Mather "B" Shaft a 3/8-yd clamshell-type bucket is used for mucking. The clamshell is opened and closed by means of a verticallymounted hydraulic ram actuated by 5000 psi oil pressure. An Ingersoll Rand-type hoist is used to raise and lower the clamshell. The hoist is controlled by one member of the crew on the floor of the shaft. When the bucket is raised, the men swing it over the muck pile to the desired position and then it is lowered on to the broken rock. The 1400-lb weight of the bucket causes it to sink into the broken rock and it digs as the ram closes the bucket. The hydraulic ram is operated by a man on the lowest shaft steel set who controls a specially designed oil pump which supplies oil pressure. The clamshell is emptied.

Jan 1, 1949

DR. E. E. SOUTHARD,* Boston, Mass.-As Director of a Psychopathic Hospital, I am a sort of "voice in the wilderness" speaking to mining engineers. I suppose that I am here because Major Gilbreth had prevailed upon me to speak on a kindred topic before the mechanical engineers at the annual meeting of their Institute. You might wonder why a psychopathic hospital, a state institution for the first care of mental cases and especially for incipient, acute and curable cases, should have any part or lot in the industrial problem. We have obvious contacts in our institution with the retarded and exceptional children of the schools, with the defective and non-defective

Jan 4, 1918

By AIME AIME

THE annual fall meeting of the Institute of Metals and the Iron and Steel divisions, in conjunction with the American .Society for Steel Treating and the Metal Congress and Show, at Boston was from many standpoints the most successful we have had to date. While many faces were missing from the various gatherings, the Institute registration reached the high mark of 324 members and guests. Cooperating with the Steel Treaters were also the American Society of Mechanical Engineers, the Society of Automotive Engineers and the American Welding Society. ,The meeting was, as usual, a three-ring circus with technical sessions &apos;galore, plant .trips, visits to the Exposition, social events such as lunch- eons and dinners as well as entertainment for the ladies present.

Jan 1, 1931

By Joseph Hays

MORE years ago than I care to admit I conferred the title of "combustion engineer? upon my-self since nobody else would confer it. I thought at the time, and for some, years thereafter, that my field was limited to the precincts where the fuel was being burned, but I found that I could stand in the door of the furnace room and hear distressed heat units calling for help all over the plant. Some of them were over-worked, others were compelled to do useless work, and still others, anxious to render a proper account of themselves, were not permitted to do any sort of work at all and were utterly wasted. The combustion engineer has something to do at that interesting occasion when the heat unit is being born in the furnace, but his responsibility does not end there. He must follow the little fellow throughout the entire period of its hectic existence in the plant and see that it gets a fair chance and a square deal everywhere. I fear that the general impression of the combustion engineer&apos;s duties is much as mine was in the beginning; that his job is limited to the implements and processes incident to the specific operation of converting fuel into active, heat energy and of applying it to the boiler, the still, or what-not, with the least possible waste. But is it not true that a heat unit saved in a remote corner of the plant means just as much to the fuel account as another saved at the furnace? And if nobody else is looking after the heat units out on the range why should the combustion engineer spend all of his time hanging around the corral? If combustion engineer is not a broad enough title to cover the man in charge of a general heat unit rescue campaign call him any-thing else you please. The job is all that counts. The name means nothing. A skunk by any other name would smell as bad. The greatest field I have ever found for general "heat rescue" work is the oil refinery. In refining we first put heat into the oil and then take it away from the vapor. The greatest heat losses occur during the cooling operation, but there are losses, many of them preventable, either wholly or partly, at every step of the several processes in oil refining.

Jan 3, 1928

By Henry D. Hibbard

I. INTRODUCTION. THESE impurities are perhaps the most important things in steel-especially steel made by the oxidation processes-the effect of which has not been at least approximately determined. By oxidation processes I mean the Bessemer and Siemens-Martin, during which the metalloids in the charge are removed by oxidation. It has been truly said that it is a clear advantage to have a new name for a new thing. To secure this and to economize space, let us adopt the name sonim (plural sonims) to designate the solid non-metallic impurities existing in steel or other metal. I would define a sonim as a solid non-metallic portion of matter existing as an impurity in metal. A piece of sand, brick, clay, or such material, imbedded in metal, would be considered as a foreign body, not as an impurity, and therefore not a sonim. The studies of sonims of which the results have been published hitherto, have been made chiefly or wholly on finished or at least on cold steel, without much, if any, regard to the specific methods by which the steel was made. While many of the results so obtained are valuable, they give little help in determining the cause, effect, or cure of the disease. It is not enough, in such a study, to know merely the commercial name of the process; for within the field of each process lies a great number of possible variations, each of which will yield a result differing in some respect from all others; and the control of sonims is particularly dependent. on the metallurgical treatment of the metal, because of the inability of analytical chemistry to throw much light on their presence, condition, and effect, as they usually occur in commercial steels. The microscope aids more, perhaps, than chemistry in their study.

Apr 1, 1911

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By H. A. Guess

AT the outset, said Mr. Guess, I may say that although I believe the present engineering courses in the various colleges and universities could be arranged to give the student within the same time limit a broader general education of un- doubted value, still I do not agree with the view held by many that engineers in comparison with those of other occupations-let us say doctors, lawyers, bankers, and so-called business men-seldom arrive at high executive positions. After all, we must remember that engineers are not very numerous as compared with the occupations just mentioned and therefore a lesser number reaching high executive positions stated numerically might be a larger number stated as a percentage. We all know there must be throughout the United States say three doctors to one engineer, but I don&apos;t think that even numerically there are as many doctors in high executive positions as engineers, and it is a fortunate thing for the country that doctors as a class are so busily engaged in alleviating sickness and suffering and in the advancement of medical science that they do not aim particularly for high executive positions.

Jan 1, 1926

By H. Larson, J. Chipman

The ferrous and ferric oxide concentrations of slags, expressed as j = Fe+++/(Fe+++ + Fe++), have been established through gas-slag equilibrium at 1550°C in a range of oxygen pressure of 10-I to 10-9 equilibriumatm. The value of j is increased by basic additions (BaO, CaO, MgO, MnO) and decreased by acidic oxides (SiO2 and TiO2). Oxygen pressure is shown graphically as a function of composition for slags which are analogous to those at the slag-gas interface of the open hearth furnace. THE progress which has been made in recent years in understanding the chemistry of metallurgical slags has been based largely on studies of slag-metal and slag-gas equilibria. There is a considerable body of knowledge which is applicable to reactions occurring at the slag-metal interface in open hearth steelmaking. There is little information concerning reactions of the slag with the furnace atmosphere and hence little basis for an understanding of the transfer of oxygen, sulphur, or hydrogen between gas and slag. The oxygen pressure of the open hearth atmosphere is normally of the order of 10-1 to 10-3 atm which differs by several orders of magnitude from that of about 10" atm at the slag-metal interface. The chemical properties of the slag, for example, the ratio of ferric to ferrous iron and the ability of the slag to hold sulphur in solution, are greatly affected by changes in oxygen pressure. This investigation was undertaken to enlarge our knowledge of the effect of oxygen Pressure on steel-making slags. Using air or controlled mixtures of CO a CO2 a range of oxygen Pressures from 10.&apos; to 10.&apos; was covered. Review of the Literature There are only a few references in the literature which pertain directly to this investigation. The most important is that of Darken and Gurry1,2 on the system iron-oxygen. This work included the determination of the phase diagram of the system and also a study of the field of homogeneous melts and their oxygen pressures. Their apparatus and procedure were very similar to that used in this study. Iron oxide was melted in a platinum crucible under an atmosphere of CO2:CO, CO2:H2, H2O, CO2, air or O2 depending upon the partial pressure of oxygen desired. After equilibrium was reached, the sample was quenched and analyzed for ferrous and ferric oxide. By appropriate calculations these authors were able to determine the oxygen and iron activities in the various slags, heats of formation of the oxides of iron, and heats of solution of iron and oxygen in the liquid slags. In a subsequent paper&apos; the same authors made a less thorough investigation of the effects of additions of lime and manganese oxide on the composition of iron oxide melts. Only a few experiments were made and those in a narrower range of temperature and oxygen pressure. Darken&apos; has investigated the fusion temperature of iron oxide in contact with silica under various atmospheres. He found that the temperature changes from 1120° to 1447°C as the gas composition changes from CO2/CO equal to 20.8 to pure oxygen. A comprehensive paper by White" predates the work of Darken and Gurry. The decomposition of ferric oxide into oxygen and lower oxides of iron was studied from 1000° to 1650°C and under oxygen pressures from 2 to 76 cm of mercury. The effect of

Jan 1, 1954

By T. A. Wright

THE CHAIRMAN.- With your permission, I shall read for F. W. Willard, who is ill, the keynote paper of a symposium that, I hope, will make us all aware of post-war problems as well as of the present-day problems in the more efficient use of secondary metals.

Jan 1, 1943