Search Documents

By H. W. Mossman

Three aspects of magnetite smelting are discussed. The first is the working out of equilibrium conditions for eliminating sulfur. The second is the influence of magnetite solubility on the difficulty of tapping the reverb matte. The third is an approximation of the equilibrium conditions in the reverb gases which govern whether magnetite is mode or reduced in the reverb slag by these gases and by any iron sulfide in the slag. MAGNETITE has had a varied history in the Hurley Smelter since its start in 1939. Magnetite determinations on the smelter products are made regularly only on the monthly composite samples. Variations on the monthly averages are shown in Table I. Magnetite which drops from the slag and matte in the reverb has some slight bottom buildup which comes and goes, but no substantial accumulation from this source has been found at the end of a normal nine months' furnace campaign. However, there has been some low grade magnetite bearing material mixed with considerable A1,0,, which has slid down from the bottom of the sloping flue between the reverberatory furnace and the waste heat boilers. This accretion has required drilling and blasting near the skimming end of the furnace. The magnetite has interfered with tapping at times. When the smelter was first started, tapping trouble from magnetite was extremely severe. Increasing the reverberatory furnace temperature by putting in an air preheater and a Dutch oven has helped greatly, although there still is occasional tapping trouble. When the present series of physical chemistry articles on copper smelting started coming out in 1950, they were read with interest, but no immediate application was seen for them. Results of some laboratory work in 1952 aroused a much stronger interest in this physical chemistry. A series of melts was made on some converter slags, which had magnetite in very large grain sizes, with the object of reducing the grain sizes in the slag, as it was known that it was easier to handle in the reverb in that condition. Anything done in the tests greatly reduced the grain sizes—even in the controls, where nothing was done except melt the slag and cast it. There was more magnetite in the slags after the tests than before, and with wide variations. There were no obvious reasons lor much of what happened in these tests. Much of the base material published in English in this field was made available for study. Recalculations were made on many of the type problems, and part of the data was reduced to local temperatures and compositions. Explanations were found for what happened in the 1952 series of tests on converter slags, and the same principles turned out to be a description of much of what magnetite does in the reverb. This article is to present the results of that study, from the viewpoint of applying the technical material in definite numerical form to the operating conditions in both the converters and the reverberatory furnaces at the Hurley smelter. Table I. Magnetite Variations on Monthly Averages, 1939 to 1955 Pet Magnetite Lowest Highest Average Converter slag 13.6 43.3 25.4 Roverb slaa 2.7 20.9 8.7 Matte 28 15.9 98 In general it was found that magnetite is made or reduced in both the converters and the rever-beratory furnace, depending on variations of temperature, matte composition, and reverb gas composition occurring in ordinary plant operation. Within reasonable limits, the field conditions for formation or reduction can be predicted, and probably can be set up and maintained. Converter conditions affecting magnetite formation can be put into numerical values better than for the reverb from purely technical calculations. The converter can be operated so as to keep the magnetite in the slag down to between 12 and 14 pct and still give satisfactory life for the converter brick. This depends upon having converter flux available which will make a slag with a good separation without raising the temperature too high. In the Hurley reverb and others with similar conditions, it is likely that a compromise of conditions will give a reasonably good control of combustion and still keep the magnetite from building up on the bottom. This discussion consists of three main parts. The first is the working out of the equilibrium conditions in the converter for determining in which direction the reaction 3 Fe,,O, (s) + FeS (1) F? 10 FeO (1) + SO, will go under actual converter operating conditions. The second deals with the influence of the solubility of magnetite in the slag and matte in the reverb on the difficulty of tapping matte. The third is an approximation of the equilibrium conditions in the

Jan 1, 1957

By BARONJUPTNER VON JONSTORFF, Andrew A. Blair, GUNNAR DILLNER

IT is a well-known fact that the results of different analysts, when operating on the same identical sample of steel or iron, are far from concordant, and it not infrequently happens that great annoyance and trouble in the commercial community are occasioned by these discrepancies. Attempts have been made at various times to investigate the causes of such differences and to obtain more reliable methods of analysis. The most important of these was made by the British Association in 1889: The following gentlemen, with Sir W. Roberts-Austen as Chairman, and Professor T. Turner as Secretary, were constituted as a committee to investigate the question, viz.: Sir F. A. Abel, Mr. Edward Riley, Mr. G. J. Snelus, Mr. John Spiller, Professor J. W. Langley, and Professor Tilden. Average .samples of steel were prepared in America under the superintendence of Professor J. W. Langley. The steels, in the form of turnings, were divided and distributed to sub-committees in Great Britain, America, France, Germany, and Sweden. In Sweden Professor Åkerman acted as Secretary to the Swedish committee. The Government Department of Tests was appointed in Germany; Mr. Ferd. Gautier in France; the British Association Committee in England; Messrs. William

Mar 1, 1905

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By Arnulf Muan, W. C. Hahn

Activities of "FeO" in "FeO"-MgO solid solutions have been determined in the temperature interval 1100" to 1300"C by equilibrating oxide samples with pure metallic iron in atmospheres of known oxygen partial pressures. The end members "FeO" and MgO form a complete solid solution series. The system shoztls a considerable positive deviation from Raoult's law. A large amount of data has been accumulated during the past 50 years on stability relations existing among various crystalline and liquid phases in oxide systems of importance in metallurgical processes. By comparison, very little is known about the thermodynamic properties within the various homogeneous phases present in the systems, particularly the crystalline phases. The present paper deals with determination of activities as a function of composition in solid solutions of wüstite ("FeO") and periclase (MgO). Such solid solutions ("Magnesiowustites") have simple sodium chloride structure and are known to be continuous between the end members at elevated temperatures (> 1000°C) and strongly reducing conditions such as prevail in contact with metallic iron. Wiistite has a defect structure in which the ratio of oxygen to iron varies and never has as low a value as 1:1 corresponding to the simplified formula FeO. Within the range of stability of this phase, the composition changes between a maximum oxygen content of approximately 25.6 wt pct (corresponding to the formula FeO.83O) and a minimum oxygen content of approximately 23.2 wt pct (corresponding to the formula Fe0-96O). The activity data to be reported in the present paper are based on using as standard state the wüstite which is in equilibrium with metallic iron at a particular temperature, i.e., "FeO" of minimum oxygen content at each temperature. For sake of simplicity, the formula FeO will be used to represent the wustite phase in the remainder of this paper. Consider the reaction 2 FeO solid solution = 2 Femeta1 + Ozgas in which FeO dissolved in another oxide dissociates to metal and gas. The activity of FeO in the solid solution, relative to "pure FeO" in equilibrium with metallic iron as a standard state, is then expressed as Here Po, and po2 * are the partial pressures of oxygen of the gas phase in equilibrium with metallic iron and the oxide solid solution or "pure FeO", respectively. The equation holds only if the metal phase is essentially pure Fe. The oxide combinations used in the present investigation fulfill this requirement. Magnesia is so much more stable than FeO that for all practical purposes aFe = 1 in the metal phase present in all mixtures used in this investigation. I. EXPERIMENTAL METHOD 1. General Procedure. The experimental method used was analogous to that developed by Foster and Welch1 and used recently by Hahn and Muan.2 It consisted of four steps: a) Determination of the equilibrium between FeO and Fe. b) Determination of d-spacing change with composition in oxide solid solutions (FeO-WO). c) Equilibration of various members of the solid solution series with a metal phase and a gas phase of known oxygen partial pressure. d) Determination of compositions of solid solutions resulting from step (c) by means of data obtained in step (b). 2. Starting Materials. General Aniline and Film Corp. carbonyl iron powder, type HP, was used as the source of metallic iron. A representative analysis was as follows: Fe, 99.6 pct; C, 0.01 to 0.04 pct; 0, 0.1 to 0.3 pct; N, 0.00 to 0.05 pct. Other elements were present as traces only. Wiistite was prepared from "Baker Analyzed" Reagent grade Fe2O3 of reported analysis as follows: Assay (Fe2O3), 98.8 pct; insoluble in HC1, 0.02 pct; not precipitated by NH,OH, 0.02 pct; Zn, 0.003 pct. Production of wüstite was achieved by a two-step

Jan 1, 1962

By R. G. Ward, John Henderson. R. G. Hudson, G. Derge

Densities of melts of the iron oxide-silica system in contact with solid iron have been measured by the maximum hubble pressure method in the composition range O to 37 wt pct SiOz and the temperature range 1255 to 1410C. The constitution of the melts is discussed and it is postulated that the structure changes from a dislribution of iron ions in an oxygen ion network at pure "FeO" to a distribution. of iron ions in a network of silicate tetrahedra at the orthosilicate composition. JOHN HENDERSON, Junior Member AIME, was formerly with the Metals Research Loborotory, Carnegie Institute of Technology, Pittsburgh, Pa., on leave from Broken Hill Proprietary Co., Ltd., Research Division, Shortland, Australia. R. G. HUDSON, formerly with Metals Research Laboratory, is now with the John Jay Hopkins Loborotory for Pure and Applied Science, General Atomic Division, General Dynamics Corp., LaJolla, Calif. R. G. WARD, was formerly with the Department of Metal lurgical Engineering, Carnegie lnstitute of Technology, while on leave from the Department of Metallurgy, University of Sheffield, England. G. DERGE, Member AIME, is Jones and Laughlin Professor of Metallurgical Engineering, Carnegie lnstitute of Technology. Manuscript submitted January 19, 1961. ISD The system iron oxide-silica is an important one metallurgically because it forms the basis of several complex slag systems in use for industrial smelting and refining processes. In recent years considerable work has been done on liquids of this system but there are still many points of difference among workers using different experimental techniques and theoretical approaches. Phase equilibria/"3 activity,4-6 electrical conductivity,' current efficiency,' transference number,8 viscosity,9 surface tension,'' and density" measurements have all contributed to an understanding of the problem. Measurement of density is one procedure which is directly indicative of liquid structure since any deviation from ideality must be a result of structural interactions. Liquids of the iron oxide-silica system are of special interest because this is one of the few metal oxide-silica systems on which measurements can be carried out conveniently over the entire composition range from pure oxide to silica saturation. This includes the range of high basicity which has received relatively little attention in other systems. Although one investigation of density in this system has previously been undertaken," the results seem of sufficient importance to warrant the independent redeter-mination reported here.

Jan 1, 1962

[Alphabetic Section (Page 1): The letter immediately following the member's name indicates grade: M-Member, A-Associate, J-Junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary Divisional affiliation: A-Mining & Exploration F-Coal B-Minerals Beneficiation G-Petroleum C-Iron and Steel H-Industrial Minerals D-Extractive Metallurgy J-Council o f Education E-Institute o f Metals K-Council o f Economics]

Jan 1, 1961

By H. G. Doll

The S.P. log is shown to be a measurement of the potential drop along the drill hole, caused by ohmic effect in the mud. The notion of static S.P. is brought forward, and its relation to the S.P. log is discussed. Other factors influencing the shape and amplitude of the log are considered; attention is given to conditions encountered in practice. Numerous figures are given illustrating graphically the results; these figures are of particular interest for comparison with field examples. The S.P. log, although indicating permeability, is not an absolute measurement of permeability, nor of porosity, of the formations traversed by a drill hole. It is affected by several parameters, such as resistivity of formations and mud, thickness of formations, and others, which should be appraised carefully. Simple rules have been established for a better distinction of the boundaries of permeabl: sections, particularly in difficult cases, such as those encountered in highly resistive formations. A systematic application of the established principles will assist in obtaining more information from the S.P. log than was possible thus far; for instance, under favorable conditions, presence of oil may be detected, or amount of shale in sands may be estimated. Introduction The S.P. log, or spontaneous potential log, has been known and widely used during the last 15 years for the location of permeable beds traversed by drill holes.1,2 In electrical logging practice, the S.P. log is shown on the left hand side track of the record (as may be seen in later examples) where it can be easily correlated and interpreted with the resistivity curves located to the right. Usually, the S.P. log consists of a base line, more or less straight, having excursions or "peaks" to the left. The base line frequently has been found to correspond to impervious beds, while the peaks are usually found opposite permeable strata. Measurements which will indicate positively the presence of permeability in the formations, and which will give accurately the boundaries of the permeable zones, are of great importance in oil-field practice. Thus far, the S.P. log is the best approach to such determinations; unfortunately, its interpretation is not always evident. With respect to the base line of the S.P. log, it may be noticed that this line is not always at a definite location on the chart. Sometimes it may shift abruptly, while other times a gradual drift is apparent. As far as the peaks are concerned, their shape is not uniform; some are rounded while others are sharp. Also, from other data, it may be found that occasionally the peaks extend appreciably beyond the boundaries of permeable zones into zones which are not everywhere permeable. A comparison with permeability measurements made on cores has often confirmed that there was no definite correspondence between the magnitudes of the peaks and the permeability values. In the same geological horizon, it generally will be found that most of the thick and permeable for-

Jan 1, 1949

By J. V. W. REYNDERS

FIRST of all let me express my affectionate gratitude for the cordiality and good will of your reception. On the part of the men I venture to interpret the character of your greeting, not only as a recognition of the position to which you have been good enough to elect me, but also as an expression of your friendly attitude. However, I cannot pass over the tribute of the ladies so casually: Nor does it seem possible to do justice to my sentiments in addressing them collectively. I would feel more equal to the task if I could have the opportunity to talk to them singly, in doing which I know I may count upon their good sportsmanship not to compare notes. There has been some discussion between Mr. Kelly and myself as to our respective duties on this occasion: The precedents are not clear as to whether the retiring or the incoming president is expected to speak at length. Mr. Kelly's argument was that as the incoming president confines himself to promises for the future his field is a broad one and his opportunities for extending his remarks correspondingly unlimited.

Jan 1, 1925

By A. H. Grobe, F. N. Rhines

AT elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible' and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscale forma¬tion) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detail5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the I-b and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 4o alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. EXPERIMENTAL PROCEDURE Silver.-The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By A. H. Grobe, F. N. Rhines

AT elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible' and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver Norbury2 and Leroux and Raub3 have reported internal oxidation (subscale formation) in alloys of silver with 2, 7 5, and 30 per cent of copper The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver' Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detail 5,6 The present research confirms this anticipation The oxidation of a series of 20 dilute alloys of silver has been studied metallographically, some types of subscale not encountered among the copper alloys have been found Instances of internal oxidation in alloys of most of the metals of the I-b and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation, i e , they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them In a study of 4o alloys of these white metals only a few cases of internal oxidation have been found The probable reasons for this difference in behavior will be discussed presently EXPERIMENTAL PROCEDURE Silver -The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99 993 per cent Ag)* and the purest avail-

Jan 1, 1942

By R. G. Wheeler, J. W. Goffard

The Larson-Miller parameter was used to correlate time, temperature, and indentation creep of magnesium, aluminum, and some of their alloys. In the temperature range 300" to 450°C, the short-time Meyer hardness of pure magnesium was less than that of the magnesium alloys tested, but for long times the pure magnesium has greater indentation creep resistance. Aluminum (1100 alloy) had 1.5 to 2.5 times more indentation creep resistance than magnesium at 300" and 450oC, respectively. Hardening of aluminum with a dispersion of Al2O3 was effective in the time and temperature ranges studied. New technologies have required the development of new materials and the utilization of the more familiar materials for new and unusual applications. The use of magnesium and aluminum and some of their alloys, because of their desirable nuclear characteristics, light weight, low cost, and ready availability, has been extended to the 300" to 450°C temperature range. In this temperature range the basic consideration of these materials must be their rate of plastic flow rather than offset yield strengths. The indentation testing reported here arose from a need for design data for the load-holding ability of supports made of these materials. Test Procedure—Hardness indents were made with a 0.275-in.-diam quartz indentor and a 10.65-lb load. The indentor was made by fire-polishing a spherical surface on the end of a fused quartz rod. The samples were held at temperature in a graphite crucible controlled to ±2°C. A thermocouple was attached to the sample and test temperatures were recorded. The diameter of the spherical indentation was measured at the end of a test period and the compression stress (Meyer Hardness) was determined by: H___________load__________ m = projected area of indent Samples were 1 in. in diam and at least 1/4 in. thick. It was observed that at the higher temperatures and longer times, the quartz indentor would stick to the magnesium sample. The quartz indentor was, therefore, frequently inspected and fire-polishing repeated when necessary. The area of sticking was always a small fraction of the area of indent and was therefore considered to have an insignificant effect on results. Correlation of Hot-Indentation Test Data with Time-Temperature Parameter—Sherby and Dorn' have correlated creep or tensile data of a' solid solutions of aluminum with a temperature and strain-rate parameter suggested by Zener and Holloman. underwood2 used this parameter to correlate creep properties of some steels with hot hardness, and upon the basis of this correlation a means of obtaining creep properties from short-time (and inexpensive) hot hardness tests has been demonstrated. Since the validity of the correlation of creep properties with a time-temperature parameter and the correlation of creep properties with hot hardness have been shown, it follows that hot hardness may correlate with the time-temperature parameter. The hot-indentation data obtained was expressed as Meyer hardness, and was shown to be time and temperature dependent. Correlation of Meyer hardness, time, and temperature with the parameter was made using the relationship: Hm = Meyer hardness t = time, hours T = absolute temperature, OK K = constant A value for the constant K was calculated by equating In l/t + K/T at different temperatures and times but at the same hardness. The correlation was tested by plotting Hm vs the parameter, In 1/t +K/T. Since materials are being sought which have high hardness at low indentation creep, i.e., a high Meyer hardness for long time at high temperatures, low values of the parameter are ofthe most interest. TEST RESULTS Magnesium—Pure magnesium (99.98 pct) cut from extruded rod was indentation tested perpendicular to the rod axis at temperatures of 300°, 350°, 400°, and 450°C for times ranging from 6 sec to 112 hr. Fig. 1 shows the time dependency of Meyer hardness at the four constant temperatures. Fig. 2 shows the correlation of the Meyer hardness of pure magnesium with the time-temperature parameter using a K of 22,720 in Eq. [I]. At the bottom of Fig. 2, the effect of doubling the time of indentation t2 = 2(t1), on the abscissa for any time is shown graphically. This effect is of constant magnitude. Also shown graphically are the magnitudes of the effects on the

Jan 1, 1960

By Robert Maddin

THE application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure has generally been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. EXPERIMENTAL PROCEDURE AND RESULTS Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,1 were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 1200 apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual X and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.3 In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig 1 shows the initial and final positions of the specimen axes of the crystals. [ ] At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to one another. Fig 3-5, photographed on different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1948

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By Jerome Strauss, Carl L. Shapiro

THIS is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years,, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I INFLUENCE OF BODY-CENTERED CUBIC ELEMENTS The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tantalum) are reviewed individually. Iron-carbon-chromium System.-In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts' concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.-Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. a; these results have received general approval. Iron-carbon-molybdenum System.-In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and Reed,8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-

Jan 1, 1943

By Joseph A. Holmes

(Pittsburg Meeting, March, 1910.) AT the Mining Experiment Station of the U. S. Geological Survey, in Pittsburg, an investigation of the process of combustion is being carried on in a specially-designed furnace having an unusually long combustion-chamber. This work is conducted by a committee consisting of H. Kreisinger, mechanical engineer; Dr. J. C. W. Frazer, chemist; and Dr. J. K. Clement, physicist. The problem, essentially one of physical chemistry, is extremely interesting to all who are concerned in the burning of coal or the construction of furnaces. The main object of these experiments is to ascertain the relation between the amount of the volatile combustible driven from the coal and the combustion-spaces necessary to burn it completely. Our best steam-coals vary from 15 to 45 per cent. of fixed combustible. The greater part of the latter is burned on the grate; but the volatile combustible leaves the freshly-charged coal and must be burned in the combustion-space. If this space is not large enough, the volatile combustible will leave the furnace only partly burned, and the result will be a considerable heat-loss and a smoky stack. Strictly speaking, the factor which determines the completeness of combustion of the volatile matter, after it has been mixed with a certain amount of air, is the length of time the mixture is allowed to remain in the combustion-space; but this length of time depends on the extent of the space itself. Let us suppose, for instance, that, when a given coal is burned at a certain standard rate, the volume of the volatile combustible driven off per second is 10 cu. ft. Adding, say, 10 cu. ft. of air, the volume of the resulting burning mixture is increased to 20 cu. ft. If the combustion-space is 20 cu. ft., the burning mixture will stay in it,

May 1, 1910

By John J. Egan

THE present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire Submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all Substances that occur or that may be in any way associated with steelmaking operations, Such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. SPECIFIC HEATS, HEATS OF FORMATION, ENTROPIES AND FREE ENERGIES OF VARIOUS PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES. I . Determination of specific heats and entropies of oxides, sulphides, nitrides, etc. over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc. over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineralogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

[Alphabetic Section (Page 689): The letter immediately following the member's name indicates grade: M-Member, A-Associate, J-Junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary Divisional affiliation: A-Mining & Exploration F-Coal B-Minerals Beneficiation G-Petroleum C-Iron and Steel H-Industrial Minerals D-Extractive Metallurgy J-Council o f Education E-Institute of Metals K-Council o f Economics]

Jan 1, 1961

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948