Search Documents

One-half fare return rate again available to members of the Institute and dependent members of their families. DON'T FORGET YOUR RAILROAD CERTIFICATE Over 300 members of the A. I. M. E. and dependent mem-bers of their families attending the last annual meeting se-cured return railroad tickets at half price by means of the railroad certificate, thereby saving several thousand dollars. DIRECTIONS 1. Be sure to obtain your railroad certificate when pur-chasing your railroad tickets for the meeting or you will lose money. 2. Purchase your tickets at regular one-way adult tariff fare between the dates specified for your territory in the accom-panying table. 3. Present your certificate for valida-tion at Institute headquarters in New York immediately after registration. Certificates will be validated on Feb. 21 and 22 between 9 a. m. and 5.30 p. in. 4. You must use your return half-rate tickets not later than Feb. 27. 5. Use the same route for both going and return trip. PLEASE REMEMBER THIS 1. Unless-250 certificates are validated at headquarters it will be impossible for anyone to secure the reduced rate. 2. Unless you secure a certificate you cannot take advantage. of the half-rate return fare, even if the necessary 250 certificates are validated.

Jan 2, 1928

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper .to, discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in. brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: 1-gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2-liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3-glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4-crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that carried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant, contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.1 At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1-aqueous solution, a much more expansible liquid, and a gas; 2-aqueous solution, salt crystals, and a gas; and 3-the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20° and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.2-6 Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid. carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.7,8 Hartley (1876, 1877),9,10 Hawes (1881),11 Wright (1881),12 Johnsen (1920),13 and Holden (1925)14

Jan 1, 1952

By W. Buchanan, O. Johari

STEREOGRAPHIC projection has been one of the most useful aids in crystal-structure studies. With the increasing use of electron microscopy in metallurgy and other fields, stereographic projection is being used in many ways1 to interpret the results from electron diffraction patterns and transmission micrographs. For many of these applications, e.g., trace analysis, twinning, and so forth standard projections of various indices are required.

Jan 1, 1967

By G. R. Love, M. L. Picklesirner

THE use of color adds a new beauty, power, and versatility to metallography. This has been amply demonstrated in a number of public exhibits and on the walls of corporate, government, and university metallographic laboratories around the world. Indeed, in a number of cases, the color not only is of esthetic value but is scientifically essential to the competent examination of particular samples and systems. Optical strain analysis,' determination of true grain size in U-A1 alloys: phase identification in Nb-base alloys,3 analysis of transformation rates in heat-treated Nb-Zr alloys,4 measurement of solidification segregation in cast Nb-Zr alloys,' study of the intermediate phases in Nb/Sn diffusion couples,6 investigation of the oxidation kinetics at various surface orientations in single crystals,7'8 and a number of other research efforts9'10 would have been vastly more difficult without the extra clarity and distinction introduced by color—either the colors resulting from particular polarized light techniques or the interference colors obtained by oxidation. It is unfortunate that the beauty of colored micro-structures cannot be shared more widely, but the economics of publishing a technical magazine apparently prohibits color plates except under extraordinary circumstances. It is doubly unfortunate that no convenient, general method exists for communicating the information available in colored microstructures to the scientific community. True, in some instances the color changes observed are dramatic enough that direct black and white photography is adequate. In photoelastic stress analysis, several orders of interference fringes may be produced and it is frequently desirable to suppress the color effects (use monochromatic light) to simplify interpretation. On the other hand, relatively minute color variations may be readily detectable by eye, be of considerable assistance in interpreting a structure, and yet be enormously difficult to reduce to an unambiguous black and white print. In order to illustrate a possible compromise or solution to the above problems, we wish to show three black and white photographs of the same region of an Nb/Sn diffusion couple whose interpretation depends heavily upon use of color techniques. These micro-structures were obtained from a section through a rod consisting of commercial-purity niobium tubing filled with 99.995 pct Sn (melt-filled in 10"6 Torr vacuum). The composite rod, measuring 500 mm long, was bent into a hairpin shape and inserted into water-cooled copper grips in a vacuum high-temperature furnace. The rod was outgassed for 2 hr at a furnace temperature of 800°C and was further heated by self-resistance using a 2.2-kva ac power supply. The rod was raised to 1910°C over a 4+-hr period, held for 15 min, slow-cooled to 1500°C over a -hr period, and free-cooled to room temperature (all temperatures were measured with W5Re/W26Re thermocouple). Throughout the heat treatment the ambient pressure was kept below 8 x lo-' Torr. Metallographic preparation of the sample was completely conventional except that it was necessary to extend the grinding steps to remove damage in the brittle NbsSn phase introduced by sectioning. No satisfactory chemical or electrochemical etch has been found for these diffusion couples; of those which have been tried, any that attack the niobium-rich phases at all attack the tin-rich phases disastrously. However, the final polishing steps did produce a slight relief effect and this, coupled with anodizing, yielded excellent clarity in the microstructures for direct observation. The anodizing voltage was chosen to give maximum change in color per unit change in composition. In this case, indeed normally, this maximum sensitivity occurred in the blue-to-red color range. The pure niobium tube wall anodized to a relatively bright blue

Jan 1, 1967

By E. A. Sondreal, P. H. Tufte

Flue gas desulfurization when burning western U.S. coals can be expected to be easier to achieve and less costly than when burning higher sulfur eastern and central coals. However, western coals cannot generally be burned in compliance with federal and state new source emission standards without some degree of control. Western coals and lignite represent about 20% of total U.S. recoverable reserves with 90% of that strip minable, and their production is predicted to increase from the 60 million tons mined in 1973 to 300 million tons in 1985. Most will be used for electric power generation, where low sulfur content is a paramount concern. Western coals are predominantly below 1% sulfur; low compared with typical values of 2 and 3% for eastern and central coals. Coal cleaning for removal of sulfur is not commercially practiced on Western coals, which typically contain half organic and half pyritic sulfur. A fraction of the pyrite sulfur could possibly be removed, but the

Jan 1, 1976

By F. J. Fayers, R. L. Perrine

For many years the problem of increasing ultimate recovery of oil from a reservoir has been a subject of interest to the oil industry. At present, a standard secondary recovery technique is to flood the reservoir with water once natural forces of the system are depleted. The permeability characteristics of the rock, together with interfacial forces which exist between the two fluids and the porous material. allow only part of the oil in the rock formation to be recovered by the water-flooding process. Laboratory experiments have shown that when detergents are added to the flooding water, the flow properties of oil in a porous rock arc improved. This improvement results in greater oil recovery. Even though higher recoveries are obtained using detergents, the extra cost associated with the method may make it economically unsatisfactory. To establish economic feasibility requires experimental laboratory measurement of fluid and rock properties together with a calculational procedure to predict field results. Pilot tests in the field may also be required. This paper presents a mathematical procedure for predicting detergent flood behavior. A number of reasonable simplifying assumptions are made to obtain a tractable system of equations. The resulting method may be regarded as a generalization of Buckley-Lev-crett' theory to solve simultaneously for water saturation and detergent concentration profiles. Consequently this type of calculation can be used in much the same manner as Buckley-Leverett theory is used to evaluate a water flood. The mathematical method employed is the so-called method of characteristics for solving hyperbolic partial differential equations. This application of the method is instructive because several other problems in reservoir analysis may be analyzed in a similar manner. FLUID FLOW EQUATIONS The flow behavior of oil and water without detergent through porous reservoir rock is usually expressed by Darcy's law and a continuity equation for each phase. If gravitational forces are neglected, vrg = kr (s)µr v p rg.........(1) vrg = kr (s)µr v p rg.........(1) ? pa va = F ?/?t (sd) where v is the volumetric flux, k represents permeability, S is saturation, and P the pressure. Fluid viscosity is denoted by 11, p is the density, 4 is porosity, and I the time. The subscripts w and o refer to water and oil. The capillary forces in the system lead to a difference in pressure between phases. This may be expressed by the relation: Pm -P0 =Pc(S).........(5) The capillary pressure? P,, is determined experimentally as a function of saturation. DETERGENT BALANCE EQUATION Addition of detergent to the water phase affects the flow properties of the system. Capillary pressure and relative permeability become functions of detergent concentration, c, as well as fluid saturation. That is: P--P (S,c) and k,,,.- - -- k,,,. At low oil saturation values, the presence of detergent reduces capillary pressure and reduces the relative permeability ratio. Detergents are surface-active and adsorb on rock surfaces. The quantity adsorbed, a, will depend on the concentration c of detergent solution and may also depend on the saturation; thus, a = a(S,c). In this analysis we have assumed that the detergents used are water soluble but not oil soluble, and their movement is therefore restricted to the water phase. The dispersion of detergent in water is neglected by comparison with transfer by flow within the system. Detergent movement is determined by the water flux and adsorption: ? cv m = -F ?/?t (cs + a) We will assume that the quantity of detergent in solution is too small to significantly change water density or viscosity. When the permeability and capillary pres-

By R. W. Smith, G. W. Delamore, J. A. Spittle

RECENT work by the authors1 has demonstrated that the crystals constituting the equiaxed zone in small ingots originate, on quenching, in the chilled liquid. Whether any partial remelting2 takes place of the den-drites nucleated in the chilled region was not examined. However, the claim3 that this normally occurs, leading to crystal multiplication, has been disputed.4 Thus, for an equiaxed zone to form in the central region of an otherwise columnar ingot, it is necessary to transport crystallites from the chill zone to this region. In view of the work of Uhlmann et al.,5 it was considered desirable to examine the transport process further. Experimental Technique and Results. In the earlier experiments by the authors.1 a stainless-steel crucible 17/8 in. diam, 41/2 in. high, ad containing an alloy of A1-4 wt pct Cu, was quenched from 660°C into a bath of Wood's metal maintained at 100°C. Under these conditions a central zone of equiaxed crystals was obtained. However, if a 2250-G unidirectional magnetic field was applied for 2 sec immediately following the instant of quenching, or subsequently, the equiaxed zone did not appear. Careful thermal analysis showed that the short application of the field had virtually no effect on the thermal conditions of the melt. It thus appeared that the crystallites which were ultimately to grow large enough to form the equiaxed zone existed in the liquid immediately ahead of the interface, occlusion being prevented by the convective fluid flow induced by freezing from the walls of the cylinder. When this relative movement was prevented by the Lorenz forces induced by the application of the magnetic field, the crystallites were caught up in the rapidly advancing dendrite solid-liquid interface. To test this assumption, a small ingot of super-purity aluminum was partially melted and poured into a heated stainless-steel mold which was then immediately quenched into molten Wood's alloy. The resulting structure is shown in Fig. 1, and consists of columnar grains with a central fine-grained zone. Thus the unmelted solid present at the beginning of solidification had been transported ahead of the columnar interface. Discussion. There appears to be little or no information available on the interaction of suspended particles with a metallic solid/liquid interface. However, some information is available for transparent organic sys-

Jan 1, 1969

By R. E. Ogilvie, J. I. Goldstein

The a and y solubility limits in the Fe-Ni phase diagram have been redetermined at temperatures above 500°C. Both a diffusion-couple and a quench and anneal technique were used. The solubility limits were measured with an electron-probe micro-analyzer. The nickel concentration at the phase boundary is increased below 700°C and the a solid-solubility range is much larger than had been previously measured. The solubility limits are also extrapolated to 300°C. It is suggested that the solubility of nickel in a FeNi reaches a maximum in the temperature interval 400o to 500°C. THE equilibrium diagram has been of great use in the field of meteoritics, where the phase relations between kamacite (a) and taenite (?) in metallic meteorites can be described by means of the Fe-Ni diagram. The study of metallic meteorites by electron-probe microanalysis has cast some doubt on the accuracy of the presently available Fe-Ni diagrams.1, 2 Recent thermodynamic studies of the Fe-Ni system also suggest that the diagram may be in error.3 For these reasons the high-temperature (800o to 500°C) part of the diagram was redetermined. INTRODUCTION The currently accepted Fe-Ni diagram is that of Owen and Liu.4 Above 910°C, there is a region of complete solid solubility, ? (fee). Below 910°C, the a (bee) phase is stable in pure iron. The effect of increasing amounts of nickel is to stabilize the y phase. The phases that form when Fe-Ni alloys are heated or cooled bear little relation to the equilibrium diagram. If an alloy is cooled from the y state and held at a temperature within the a + y field, no evidence has been found for the occurrence of the y - a transformation.5 If the alloy is cooled to low enough temperatures the y phase breaks down into a supersaturated bee phase called a2. In fact, in alloys over 27 pet Ni the y phase is retained at room temperature.6 The a, phase has the same composition as the original y. The temperature at which a2 forms, the M, temperature, has been determined experimentally.' A state of equilibrium can be approached by cooling below M, to form a2 and then reheating the alloy into the two-phase region of the diagram. The y phase will then begin to precipitate out of the a2 phase and grow. The growth of the phase, however, is quite slow. Using the interdiffusion coefficients -Da of Goldstein et al.,8 it is estimated that it takes about 1 year to grow a 10-µ-wide region of ? at 700°C in a 5 pet Ni alloy. Owen and Liu4 used the technique just described to form the equilibrium phases. The phases present were determined by means of X-ray analysis. The accuracy of their diagram depends on the number of alloys available near the phase boundary at a given temperature. In this study two different techniques were used to determine the a/a + ? and ?/a + ? solubility limits. The inherent accuracy of both techniques was greatly improved over that used by previous investigators because the phase-boundary compositions were measured with an electron-probe microanalyzer. PROCEDURE The two methods used to determine the Fe-Ni diagram are the diffusion couple (D.C.) and the quench-and-anneal (Q.+A.) techniques. In the first method, diffusion couples whose diffusion path goes through a two-phase region of the phase diagram were used. A description of the technique used for making the diffusion couples has been described in a previous paper.' After the diffusion treatment a discontinuity in the resultant concentration vs distance profile was measured. The nickel concentrations in the a and ? phases at the interface of the discontinuity are the solubility limits of the a and ? phases in the phase diagram at the diffusion temperature. If the interface com-

Jan 1, 1965

By Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table I), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term "potash" originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first U.S. patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 20.4 million short tons K2O produced in the world in 1970 (Eilertsen, 1971 ) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K,O, a unit of measure which is neither a natural nor synthetic compound of potassium (1 .O% K is equivalent to 1.2046% K,O) . Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and meta- morphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such de- posits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of sea-water or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in [Table 1]. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971).

Jan 1, 1975

By B. M. Larsen, T. E. Brower

In an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats ill different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper,2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, A[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus perinits more definite conclusions to be drawn. This excess concentration of oxygen, A[O], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration A[0] in liquid steel varies from about 0.009 to 0,035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following: i[O] Usual Per Cent Oxygen by Conditions Weight 1. Vigorous lime boil........... o.oog-0.01s 2. Steady state................ o.or;-0.025 3. Working of ore.............. o.023-0.035 Thus when the bath can be regarded as in a reasonably steady state—that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour—A[0] returns from

Jan 1, 1948

By B. M. Larsen, T. E. Brower

In an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats ill different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper,2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, A[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus perinits more definite conclusions to be drawn. This excess concentration of oxygen, A[O], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration A[0] in liquid steel varies from about 0.009 to 0,035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following: i[O] Usual Per Cent Oxygen by Conditions Weight 1. Vigorous lime boil........... o.oog-0.01s 2. Steady state................ o.or;-0.025 3. Working of ore.............. o.023-0.035 Thus when the bath can be regarded as in a reasonably steady state—that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour—A[0] returns from

Jan 1, 1948

By H. M. Howe

THIS paper presents an experimental verification of some of the predictions made by one of us' concerning 'the influence of certain conditions of casting upon the size and position of the pipe', and the position of the segregate, in steel ingots. The predictions which we have been able to verify are the following A. That the pipe is shortened and the segregate raised 1. By slow casting; 2. By casting with the large end up instead of down; 3. By retarding the cooling of the top, e.g., by means of a sinking-head. B. That the pipe is shortened by slow cooling. C. That the pipe and segregate lie in the last freezing-part. Our procedure was to cast ingots of wax (commercially pure stearic acid) containing a little bright green copper oleate (usually 1.5 per cent.) under varying conditions; to saw each ingot open along a longitudinal plane passing through its axis ; and to examine the longitudinal section thus laid bare. In order to make the segregate or enriched part more distinct in color from the impoverished part, a very little red cerasine was added. An experiment which will be described later showed that the cerasine itself does not segregate markedly, if at all. Hence we may assume that the strong contrasts between the green and red shown in so many of our ingots are due, not to segregation of cerasine, but to that of the green oleate, in the wax which in itself is uniformly reddened with cerasine.

Jul 1, 1907

By C. J. Guntner, R. P. Reed

A commercial 18Cr-8Ni iron alloy (AISI 304L) was examined in tension at 300°, 76°, 20°, and 4°K. Continuous stress-strain recordings were made, X-ray analyses at periodic stress (strain) intervals were obtained, and the magnetic measurements were taken. From this data the percentage of martensitic products [bcc(a) and hcp (E)] was computed as a function of stress (strain). It was found thatup to 15 pct E phase forms at low temperntures. The amount of E formed increases to a maximum at about 5 pct strain, then decreases. This decrease indicates the additional transformation of E to a'. The total amount of E and a' was suppressed at constant stress (strain) at 4°K as compared to 76°K. It is proposed that the suppression of E and a' is associated with the decreased mobility of extended dislocations at very low temperatures. The yield strength decreased as the temperature was depressed below room temperature and then increased rapidly near 4°K. SOME ferrous alloys which are austenitic (fcc ?) at room temperature appear to be unique in that two martensitic products (hcp e and bcc a') may form on cooling to lower temperatures or on application of mechanical stress. The most common room-temperature austenitic ferrous alloys are 18Cr, 8Ni stainless steels. Most aspects of the spontaneous transformations have been previously described for these steels.' Several previous papers have described special aspects of the stress-induced transformations at low temperatures for the stainless steels, such as the existence of the hcp phase (c) after straining at 76oK,2-7 the morphology after straining using electron microscopy,7 and the decrease in E at higher strains at 76oK.4 However, for a complete representation, one must know the stress-strain characteristics and the dependence of both martensitic products on applied stress and temperature. It is the intention of this paper to provide that documentation. To accomplish this, continuous stress vs strain recordings were made at four temperatures: 300°, 76", 20°, and 4°K for annealed AISI 304L (a commercial 18Cr-8Ni alloy). At periodic stress intervals at each temperature the integrated X-ray line intensity of a selected peak for each phase (y, E, and a') was measured. In addition, photomicrographs of the strained surfaces were taken and magnetic measurements were made. The magnetic readings can be directly converted into percent a'.',e With these measurements the percentage of each phase may be plotted as a function of stress (or strain) and test temperature. It was found that up to 15 pct E phase forms upon stressing the AISI 304L alloy at low temperatures. The E percentage increases abruptly after the alloy yields, but then decreases gradually at higher stresses. The rapid increase in e at 76°K is associated with an "easy-glide" portion of the stress-strain curve. The total amount of a' + .G is suppressed below 76°K at a constant stress or strain. The yield strength decreases down to 76°K but increases rapidly below 20°K. EXPERIMENTAL PROCEDURE Tensile test specimens were cut parallel to the rolling direction from 0.1-in.-thick sheet. Continuous stress vs strain recordings were obtained at each test temperature (300°, 76o, 20°, and 4°K) using equipment and methods described elsewhere.' The specimens which were used in the X-ray analysis were stressed to successive increments of strain at each temperature, analyzed at room temperature, then restressed at the test temperature. This procedure was repeated until approximately ten X-ray analyses had been performed with approximately 1.0 pct strain increments. The specimens had a reduced section 1 in. long, 1.2 in. wide, and 0.1 in. thick. They were electro polished prior to testing and after each strain increment. Table I lists the chemical composition, grain size, and hardness for the alloy which was used. This is the same alloy for which extensive mechanical-property tests3 and morphological studies of the spontaneous transformations' have previously been made. For the low-temperature tests (76o and 4°K) below the Ms temperature the specimens were initially cooled to the test temperature, held for 1/2 hr, then warmed and X-rayed at room temperature. The results are listed in Table 11. From earlier work8 it was known that additional transformation on the second cycle would be considerably less (-0.1 pct

Jan 1, 1964

By J. H. Brophy, S. J. Michalik

A constitution diagram for the system Mo-Ir has been determined. The maximum solubility of iridium in molybdenum is 16 at. pct at 2110ºC and decreases to less than 5 at. pct at 1500°C. The solubility of molybdenum in iridium is 22 at. pct. Three intermediate phases appear in the system: 8 MoJr, having the p-tungsten structure; a phase, a cornplex tetragonal structure; and the hcp ? phase. Metallography, melting point determinations, X-ray diffraction and fluorescence, and electron micro-probe unalyses were employed in establishing the diagram. PREVIOUS to the present investigation, the intermediate phases in the Mo-Ir system were identified, but no detailed account of the phase diagram has been reported in the literature. Raub1 investigated alloys of Mo-Ir over an extensive range of composition between the temperatures of 800º and 1600°C. The in-termetallic compound MosIr was found to exist with nearly pure molybdenum, as the solubility of iridium in molybdenum was not detectable parametrically in this temperature range. MO3Ir was found to be iso-morphic with a ß-tungsten type structure, having a parameter of 4.959Å. An intermediate hcp phase, designated as the ? phase, ranged in composition from 52 to 78.5 at. pct at 800ºC, and from 41 to 78.5 at. pct Ir at 1200°C. Parameters noted for the ? phase were as follows: at 42.7 at. pct Ir, a = 2.771i0, c = 4.4366, c/a = 1.601; at 78.5 at. pct Ir, a = 2.736A, c = 4.378A, c/a = 1.600. Molybdenum was found to be soluble in iridium up to 16.5 at. pct Mo (83.5 at. pct Irj, with the parameter of iridium increasing to 3.845A at the solubility limit. Knapton,2 who investigated alloys between 15 and 85 at. pct Ir, essentially agreed with Raub's data, but, in addition, found a a phase in as-melted alloys near 25 at. pcto Ir. The oaphase lattice parameters were a = 9.64Å, c = 4.96Å, c/a = 0.515. The a phase was replaced by the 8 -tungsten phase on annealing at 1600°C. Knapton concluded that the a was stable only at elevated temperatures, and placed the composition of the a phase at approximately 30 at. pct Ir. The intermetallic compound Mo3Ir, with a lattice parameter of 4.965A, was included among the 8-tungsten structures reported by ~eller.' Matthias and Corenzwit,4 and Bucke15 studied the superconducting nature of MosIr, and reported a superconducting transition temperature of 8.$K. The present investigation describes the phase relationships in the Mo-Ir alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURES Alloys for the determination of the phase diagram were prepared from powders. Commercial 99.9 pct Mo from Fansteel Metallurgical Corp. and 99.9 pct Ir powder from J. Bishop and Co. Platinum Works were used. The powders were weighed to nominal compositions, mixed, and then pressed, without binder, into compacts weighing 4 to 6 g. These were presintered in uacuo between 1200' and 1400°C for 1 hr, to reduce the degree of spattering during subsequent arc-melting. The compacts were arc-melted in a nonconsumable tungsten electrode furnace six times on alternate sides on a water-cooled copper hearth in an atmosphere of zirconium-getter ed argon at 500 mm of mercury pressure. In almost all cases, this procedure yielded buttons of satisfactory homogeneity. The composition of all melted buttons were confirmed by X-ray fluorescent analysis using the experimentally determined ratio of the iridium La1 line intensity to that of the molybdenum Ka1 line as a function of composition. In this determination four alloys analyzed by wet chemical methods were used as standards. An uncertainty range of ±1 at. pct has been attributed to all indicated compositions. All heat treatments and solidus measurements were carried out in tantalum resistance heating elements in vacuum conditions of 10-4 to 10-5 mm of mercury. A detailed account of this procedure has been reported by Schwarzkopf and Brophy.8 In the heat treatment and solidus measurements of iridium-rich alloys (50 at. pct Ir or greater), a tungsten lining was inserted into the tantalum resistance heating element because of a eutectic reaction which occurs between iridium and tantalum at 1948ºc.7 Heat treatments and solidus measurements carried out at compositions less than 40 at. pct Ir both with and without tungsten linings within the resistance

Jan 1, 1963

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

By H. T. Bowman

FOR more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the 1860's it was recognized that the process would benefit by some type of instrumental control.1 However, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower's eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham3' A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient monoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. CARBON-FEO RELATIONSHIP In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by McCutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a different method than were those

Jan 1, 1942

By Joe O. Ledbetter

INTRODUCTION Health physics as a profession really got a significant start during the Manhattan Project of World War 11. The Health Physics Society has recently published its 25th anniversary issue of the journal (June 1980). There was concern over radiation exposures during and after uranium production, especially about radium and its daughter products [Jackson 19401 and, as evidenced by the frequency of articles in the literature, there still is. The reason for this concern was expressed by Harley as "Workers engaged in the mining and pro- cessing of radium-bearing materials are exposed to dusts of the parent, to radon, and to the radon daughter products. In- haled radioactive particulates may be retained in the lung or redistributed to other organs of the body. Relatively minute de- posits of radioactive substances, particularly alpha emitters, have been clearly shown to be the etiological factor in a variety of injuries to industrial and re- search workers. " [Harley 1953] Emphasis in measurements has been placed on radium in water and radon in air, since these are the principal mobilized phases; however, it should be kept in mind that radium-containing particles do become suspended in air as aerosols and radon absorbs in liquids. Much of the uranium mining and production is being carried out aboveground. The principal difference between underground and surface (pit or leach) mining of uranium is the reversal in the relative importance of roles for the types of radiation dose. For aboveground the major radiation exposure is external gamma ray, whereas for underground it is internal alpha; for aboveground, the whole body penetrating is of greater importance than the lung alpha dose. AS a result of the politics involved and the law- suits for any and all diseases as being occupationally- caused, today , more than ever before, the successful performance of the activities connected with uranium production--before-, during-, and after-the-fact-- must include the provision of first class radiation protection. Such protection can be achieved by good measurements, thorough risk evaluations, and adequate controls. Meeting the ALARA (As Low As Reasonably Achievable) philosophy necessarily entails the determination of what is reasonable exposure. The necessary and sufficient elements of radiation safety under the ALARA dictum require a hard look at the dose versus effects data. There are times when the health physicist needs to make decisions of judgement rather than compliance with a well-defined regulation value. In order to facilitate such decisions, the real world must be separated from opinions that are merely artifacts of statistical variation and from the unprovable "what ifs" that are slanted to question the morality of any non-Luddite. UNITS VOCABULARY FOR DOSIMETRY There have been many radiation quantifying and dosimetric units introduced in the past. Fortunately, most of them did not catch on enough to become required knowledge for reading the health physics literature. The unit definitions necessary for our purposes here are the following: -curie (Ci)--unit of radioactivity equal to 3.7 x 10 10 disintegrations per second Webster&apos;s 19711 or the quantity of radionuclide that undergoes 3.7 x 10 nuclear transformations per second. Environmental levels of radioactivity are usually measured in picocuries (10-l2 Ci) per cubic meter for air and in picocuries per liter (pCi/~) for water and sometimes for air. .roentgen (R)--exposure dose of x or gamma rays that gives 1 esu of charge (either sign) to 1 cc of dry air @ STP. The roentgen is equivalent to an energy absorption of 86.7 ergs/g of air [Gloyna and Ledbetter 19691. .rad--radiation absorbed dose of 100 ergs per gram of absorber. The SI unit for absorbed radiation dose is the Gray; 1 Gy = 100 rads. orem--radiation absorbed dose of 1 rad times the quality factor (QF) for that radiation. The QF is 1 for x rays, gamma rays, beta rays, and posi- trons. For heavy ionizing particulate radiation, QF is a function of the amount of energy trans- ferred per unit length of travel, i.e. , the linear energy transfer (LET); the values of QF:LET in keV/um are as follows: 1:<3.5; 1-2:3.5-7; 2-5:7-23; 5-10:23-53; and 10-20:53-175 [Morgan and Turner 19 671 . For radiobiology, relative biological effectiveness (RBE) is recommended for use instead of the quality factor above that is for radiation protection: the RBE is the ratio of the dose of 200 kVp x rays to the dose of radia- tion in question (both in rads) to cause the same

Jan 1, 1980

By C. L. Magee, H. W. Paxton

The effects of testing temperature, frorn 77" to 420" K, and volume fraction of martensite on the micro-plastic response of unaged Fe-31Ni martensite-austenite aggregates have been determined. The kinetics of the aging phenomena which lead to a decrease in the microplastic response were also characterized. These determinations, supplemented by other experimental results, show that at least two mechanisms of plastic deformation give rise to the apparent softness of the quenched structures. Only one of these mechanisms is fully discussed in this paper The transformation of retained austenite to martensite during the application of stress leads, in specified conditions, to large microplastic strains. This deformation behavior cannot be described by normal transformation plasticity theory but is shown to result from the fact that stress-assisted formation of martensite is a possible deformation mode. The present results and further considerations of previous work lead to the conclusion that it is unnecessary to postulate a special work-hardening mechanism to explain the mechanical properties of unaged martensite. It is now generally accepted that dislocation motion can occur in many solids at stresses very much below the L&apos;macroscpic" yield stress, e.g., 0.1 pct offset. This phenomenon has been investigated by a variety of techniques including measurements of elastic limit,&apos; effective static elastic modulus,~ and irreversible deformation following stressing at low levels.3"5 Of particular interest to the work to be described are exper -iments conducted on the deformation of martensite in attempts to decide whether freshly quenched ferrous martensites are "hard" or "soft".6 Muir, Averbach, and cohenl and McEvily, Ku, and ~ohnston&apos; have shown that as-quenched ferrous rnartensites can be plastically deformed at relatively low stresses. A difference between these two sets of experiments exists in that some diffusion of carbon would take place before testing in the experiments of Muir et a1. because the plain Fe-C alloys which they have tested transform to martensite well above room temperature. McEvily et a1. examined Fe-Ni-C alloys with Ms of about -30"~ and tested the alloys directly after quenching to — 195" ~ —a technique which obviates any appreciable carbon diffusion. Unfortunately, a characteristic of the alloys which transform below room temperature is that they do not transform entirely to martensite. The results discussed below will show that, because the transformation of this retained austenite under stress leads to plastic deformation, one cannot investigate the properties of martensite by such experiments. The existence of a second deformation phenomenon, which is not caused by retained austenite, is also established in the present work. In line with a previous suggestion,&apos; it is believed that the second microdefor-mation mode is principally due to the internal stresses generated by the formation of martensite. To avoid confusion in the present report, the evidence we have found for this interpretation will be discussed separately in a brief note.7 EXPERIMENTAL Materials. The alloys were induction-melted and cast under vacuum; the resulting compositions are given in Table I. The ingots were hot-swaged to 2-in.-diam bar and further cold-swaged and/or cold-rolled prior to specimen preparation. The standard tensile specimens were machined from sheet. The gage section was 0.05 by 0.2 by 5 in.; 0.75-in.-wide ends had 0.2 5-in. centered holes for pinloading. The three-point bend samples were 0.075-in. thick and 0.6 in. bide. The distance between the outer loading points was 5.5 in. In order to establish a standard starting condition, all specimens were quenched to 77°K prior to annealing in vacuo for austenitizing. The temperature of the austenitizing anneal was controlled to + 5"~. The testing and aging temperatures were maintained by various liquid baths (nitrogen, 77"~; freon, 130° to 200°K; acetone, 200 to 300°K; silicone oil, 300&apos; to 450°K) to better than il°K. Strain Measurement. The results herein were derived from both uniaxial tension and three-point bending experiments. For bending tests, the stresses and strains reported are those corresponding to the maximum fiber values. Normally, because of the small strains involved, very sensitive strain measurements are necessary to make microplastic measurements. However, because of the magnitude of the dilatation and shear involved in the martensitic transformation, the requirements in the present experiments proved to be less rigorous. In most experiments the plastic strain was evaluated by measuring stress relaxation and modulus defects. In this method, specimens are loaded rapidly to some predetermined load on an In-

Jan 1, 1969

By L. T. Lloyd, H. H. Chiswik

The operative deformation elements in a-uranium single crystals under compression at room temperature have been determined as a function of the compression directions. The deformation mechanisms noted may be arranged with respect to their frequency of occurrence and ease of operation in the following order: 1 — (010)-[I001 slip, 2—{130} twinning, 3—{~172} twinning, and 4bunder special conditions of stress application, kinking, cross-slip, {.-176) twinning, and (011) slip. The composition planes of the (172) and (176) systems were found to be irrational. Cross-slip was shown to be associated with the major (010) slip system, coupled with localized interaction of slip on the (001) planes. The mechanism of kinking was found to be similar to that observed in other metals in that it occurred chiefly when the compression direction was, nearly parallel to the principal slip direction [loo] and was associated with a lattice rotation about an axis contained in the slip plane and normal to the slip direction: the [001] in the uranium lattice. The resolved critical shear stress for slip on the (010)-[100] system was found to be 0.34 kg per mm2 In a single test it was shown that under compression in suitable directions twinning on the (130) also occurs at 600°C. DEFORMATION mechanisms of large grained polycrystalline orthorhombic a-uranium have been studied by Cahn.1 A major slip system identified as the (010) with a probable [loo] slip direction and a minor slip system on the (110) planes were reported; the slip direction of the minor system was not determined. The twinning systems that were identified experimentally included the (130) and the irrational (172) composition planes; observations of other traces which were not as frequent and which did not lend themselves to positive experimental identification led Cahn to postulate on the basis of indirect evidence that twinning also occurred on (112) and (121) planes. In addition to the foregoing slip and twinning mechanisms, Cahn also observed kinking and cross-slip in conjunction with the major (010) system; the cooperative cross-slip plane was not identified. The availability of single crystals to the present authors has enabled them to check these results, particularly with reference to the doubtful mechanisms and the preference of operation of any one mechanism in relation to the direction of stress application. The tests were confined to compression only, primarily because of experimental limitations imposed by the size and shape of the available crystals. The tests were performed at room temperature except for one crystal compressed at 600°C. The compression directions were chosen to obtain a representative coverage of one quadrant of the stereo-graphic projection. To test the existence of some of the deformation elements that were reported by Cahn, but were not found in the present study, several additional crystals were compressed in specifically chosen directions considered most ideal for their operation. Experimental Techniques The single crystals were obtained by the grain coarsening technique described by Fisher? They grinding and polishing on rotating laps, with final surface preparation performed in a H3PO4-HNO3 electropolishing bath. A typical crystal readied for compression is shown in Fig. 1; their dimensions were rather small and depended upon the testing direction. Crystals isolated for compression in a direction close to the [010] axis, which lay roughly parallel to the longitudinal axis of the polycrystalline rod, were about 3 to 4 mm long and 5 mm2 in cross-section, while those prepared for compression in other directions were smaller. Most of the crystals were free from twin markings and showed no evidence of Laue asterism. Several crystals, however, contained twin traces prior to compression; these were identified prior to compression so as to clearly distinguish them from those initiated during deformation. The origin of the twin markings prior to deformation may be ascribed to two sources: thermal stresses and specimen handling during isolation and preparation. Two other types of imperfections in the crystals should be mentioned: inclusions, which were probably oxides or carbides. and three of the crystals contained a small number of spherical included grains (<0.01 mm diam), which were remnants of unabsorbed grains from the coarsening treatment. The volume represented by these imperfections was small, and their presence presented no difficulties in the interpretation of the macrodeformation processes during subsequent compression. Two compression fixtures were employed: crystals A, B, C, E, and G were compressed in a hand-operated screw-driven jig whose compression platens were designed to minimize axial rotation;

Jan 1, 1956

By H. H. Reamer, B. H. Sage

The formation volume and the relative volume of the liquid Phase of mixtures of Condensate and gas from five different parts of a field in the Louisiana area have been established experimentally. These studies included gas-condensate ratios as high as 25.000 cu ft/bbl at pressures up to 5,000 psi. The gravities of the tank condensates were between 53.9° and 63.9° API. The compositions of the condensate and gas samples inves-ligated are presented in tabular form. The formation volume. the relative volume of the liquid phase. and the specific volume of the mixtures are available. A rough correlation of the formation volume as a function of pressure. temperature, and gas-condensate ratio has been presented. This correlation i-considered applicable only to the range of conditions covered in this investigation for systems of similar nature and com-position. INTRODUCTION Often a knowledge of the influence of temperature. Pres sure, and relative quantities of condensate and gas upon the volumetric behavior of fluid*. from a given field has been employed in estimating the Conditions existing in the reservoir. The early work of Beecher and Parkhurst&apos; and the more rrcent Studies of the Dominguez&apos; and San Joaqnin Valley Field;: are examples of experimental studies of this character. Correlation of the volumetric behavior of naturally occurring hydrocarbon mixtures has Proved To be feasible&apos; . at low gas-conden-sate ratios-; for fluids*. from a single geographic area. Progres 5 is being made in the Prediction of the volumetric behavior of distillate systems at high gas-condensate ratios and pressure.. However. the estimation of the retrograde". &apos; dew-point pressure still remains uncertain and probably can best be established by experiment. For this reason it appears of interest to make available experimental information about the volumetric behavior of mixtures of condensate and gas from five different part.; of a single field. This material shows a rough similarity to data for mixtures of condensate and gas from San Joaqnin &apos; Valley Fields. In the present paper. 110 attempt has been made to coordinate the available information on tbe volumetric behavior of fluids from condensate fields. It appears hopeful that progress can be realized by the utilization of recently developed equa-tions of state.!&apos; However. the primary problem in any such correlation is the proper identification of the components and constituents of naturally occuring systems. Additional experimental information may be required to permit the determination of the values of the constants of the equation of state for References given at end of paper. Manuscriptt received in the office of the Petroleum Branch June 11. 1951. *For present purposes low gas- condensate ratios will he considered as those below 3,000 cu ft/bbl, and the region of high gas-condensate ratio will be limited to compositions containing more than 5,000 cu ft of pas per bbl of condensate. Mixtures Containing between 3,000 and 5.000 CII ft OF gas per bbl will be considered of intermediate gas-condensate ratio.

Jan 1, 1952