Search Documents

By Gerald Edmunds, M. L. Fuller

The development of "fiber" or preferred orientations, during the plastic deformation of metals, and the relation of such structures to the anisotropic characteristics of worked metals has become a subject of common knowledge among metallurgists. Very little has been published, however, relative to variations existent throughout the cross-sections of rolled strips,1 and the influence that such variations may have. This paper presents such a study on a rolled zinc alloy.2 The significance of small differences in surface structure is shown in relation to bending properties. Experience with zinc and its alloys has shown that the outer radius of the bend, which is subject to tensile deformation, is the common region of failure. In considering relations of structural characteristics to bending properties it will suffice, therefore, to consider the ease and possible extent of tensile deformation resulting from various orientations. It is necessary in this connection to assume that on the average the individual crystals of a polycrystalline material act substantially as if their movements were unobstructed by the surrounding grains. This assumption is not strictly valid, but the error involved is unlikely to affect seriously the qualitative conclusions derived from its use. The mechanism of the plastic deformation of zinc crystals has been described by Mark, Polanyi and Schmid3 and by Mathewson and Phillips14 and is regarded as being accomplished by block movements or * Investigator, Rolling Mill Section, Research Division, New Jersey Zinc Co. f Investigator, X-ray Laboratory, Research Division, New .Jersey Zinc Co. 1 Variations of structure throughout the cross-section of wire have been reported in the literature. 2 This alloy contained, in addition to zinc, 1.0 per cent copper and 0.01 per cent magnesium. Its crystal form is hexagonal close packed, the sarne as that of pure zinc. 3 H. Mark, M. Polanyi and E. Schmid: Vorgange bei der Dehrlung von Zink-kristallen. Zlsch. f. Phys. (1922) 12, 58. 4 C, H. Mathewson and A. J. Phillips: Plastic Deformation of Coarse-grained Zinc. Proc. Inst. Met. Div., A. I. M. E. (1927) 143. C. H. Mathewson: Twinning in Metals. Proc. Inst. Met. Div., A. I. M. E. (1928) 7. The results of a further study of plastic deformation of zinc as related to twin-

Jan 1, 1932

By H. Rush Spedden, A. M. Gaudin

ALTHOUGH the number of minerals that are ferromagnetic) or highly paramagnetic is strictly limited, it has been known for some time that many minerals have slight but supposedly characteristic magnetic susceptibilities. With the exception of pyrrhotite, however, sulphides have been thought nonmagnetic. A new magnetic separator has been made available recently in limited quantity to research laboratories. This device, the Frantz Isodynamic Separator, has been used for the separation of various nonsulphides from each other. Its application to the separation of sulphides, however, does not seem to have been reported. In the Richards Mineral Dressing laboratories, the success achieved through the use of this device in separating associated sulphides has been so startling as to lead us to believe that it constitutes a magnificent adjunct to heavy-liquid separation and to quantitative mineragraphy as a tool for the mineral investigator. THE SEPARATOR The separator (Fig. I) consists of: I. A powerful magnet, the strength of which can be adjusted by means of a rheostat; 2. A vibrating chute of nonmagnetic metal on which the mineral to be separated is made to flow (Fig. 2); 3. A feed bin and adjustable feeder; 4. Receptacles for the collection of products; 5. Means for changing, setting, and accurately reading the two slopes of the chute; viz., the cross slope and longitudinal slope. The separator is made operative by the special shape of its pole pieces, which ensures a strongly converging field. It is said by the makers of the machine that the pole pieces apply a constant mechanical force to a particle of given susceptibility, regardless of its position in the operating space of the separators.* Susceptible particles, therefore, behave as though of lower specific gravity than under ordinary circumstances. This effect, combined with the slopes of the chute and the action of the vibrator, causes a stratification not unlike that obtainable on a shaking table. The chute is of rectangular cross section, and shallow; it is broadened toward the discharge end and divided longitudinally by a partition into two compartments that lead to the collecting receptacles. Although the separator probably can be used to make separations at fairly coarse

Jan 1, 1943

By B. M. Loring, W. H. Baer, G. M. Carlton

It is a well known fact that age-hardening alloys remain in a supersaturated, or partially supersaturated, condition only for limited periods of time at temperatures below the solvus. In order to develop optimum properties by subjecting the quenched alloy to precipitation or age-hardening treatment at a specified temperature, it is necessary that the cooling rate be sufficiently high to maintain the required degree of supersaturation of the solid solution. In practical applications the size and shape of the specimens obviously have considerable influence on the rate of cooling and there is need for more information on the effects of various rates of cooling. Cooling rates of quenched aluminum alloys generally have been established by the type of quenching medium, the temperature of the medium and the dimensions of the specimen. Except for the work of Roth3 little quantitative information is available on the measurement of cooling rates of aluminum alloys and the significance of the influence of various cooling rates upon the mechanical properties. The purpose of the present investigation was to study the use of the Jominy test for aluminum alloys (Table I). The material for this investigation consisted of extruded rods 1 1/4 to 136 in. in diam. The chemical compositions were as follows: The modified L-type Jominy specimen with dimensions shown in Fig I was selected as the most convenient means for obtaining a wide range of cooling rates. The standard Jominy specimen was not satisfactory because its cooling rate was not sufficiently high. The four flat surfaces machined at right angles along the length of the L-type specimen to a depth of 0.015 in. facilitated the hardness measurements. The specimens were machined from the extruded stock with no intermediate forging. New specimens were used for each aging experiment. The specimens were given solution treatments of 2 hr duration at recommended temperatures in a Hoskins furnace (Table 2). The temperature of the furnace was maintained constant to 3°C. No protective atmosphere was necessary because the thin film of oxide that formed on the surface of the specimens had no effect on the hardness measurements. AT

Jan 1, 1949

By R. M. Treco

THE thermal expansion of pure beryllium was first investigated by Hidnert and Sweeneyl in 1925 on a single cast specimen stated to be of 98.9 pct purity. A study of the coefficients of expansion by X-ray methods has recently been made by P. Gordon' on powder obtained from the Brush Beryllium Co. assaying 97 wt pct beryllium with about 2 wt pct oxygen as an impurity. The present work pertains to about the highest purity metal obtainable from the Brush Beryllium Co. This metal was in the form of lumps which were remelted and cast in a high-vacuum induction furnace. Expansion data in this paper deal with beryllium extruded into bars of rectangular cross-section 4x1/2 in. and the anisotropic expansivity of a large cast single crystal. Analysis of the cast metal after extrusion indicated a beryllium assay of 99.28 pct. Impurities were 0.170 pct Fe, 0.140 pct Al, 0.014 pct Mg, 0.086 pct Si, 0.020 pct Cu, 0.020 pct Mn, 0.007 pct Ni, 0.007 pct Ca, 0.080 pct C, 0.179 pct 0, (as BeO). Part I—Extruded Metal Thermal expansion measurements were obtained with a fused quartz-tube differential type dilatom-eter3 on specimens cut from the extruded sections in longitudinal and transverse directions. Specimens were machined to a diameter of 0.250 in. and a length of 3.000 in. One sample from each direction was vacuum annealed for 1 hr at 800°C. The dilatometer tube was placed in a vertical tube furnace having a uniform temperature zone which was twice the length of the sample. Average time for a complete thermal cycle to 500°C was 18 hr. Temperatures were observed with two chromel-alumel thermocouples attached to the sample about 1 M in. apart. The accuracy of temperature measure-ment was ± 0.25°C. An argon gas atmosphere sur-rounded the specimen to prevent oxidation of the beryllium. Samples were identified as shown in table I. Results - The original plan included measuring expansion up to 1000°C, but the first two runs on sample No. 5 showed that a permanent contraction occurred from

Jan 1, 1951

SINCE I told you in the preceding chapter how the potter's art is followed in practice, now in this following one I wish to tell you how mortar* and bricks are made, and how and to what purpose they were discovered, although I know you will answer that you know it, inasmuch as it is an art known not only to skillful men but also to the unskilled ones by whom it is practiced, and that bricks and mortar were made and always will be made for the purpose of building. This I admit, but probably everyone does not know it as you do, and you perhaps, do not know its beginnings, although I remember having told you of them. Wishing to repeat it better now I shall begin with long ago, so that both you and I may be better satisfied. Therefore I tell you that you should know that all the arts that men practice in the world have been learned by them either through the process of reasoning from the principles of natural phenomena, from the actions of animals, by chance, or when forced either by some necessity or

Jan 1, 1942

By J. E. Pogue, F. G. Coqueron

This paper describes the sources of funds required by the petroleum industry to finance capital expenditures and also presents a discussion of the effect of rising construction costs on these expenditures. The petroleum industry obtains its capital funds from several sources: (I) internal, from retained cash earnings; and (2) external, from borrowings and the sale of securities to the public. The upward trend of capital expenditures of the petroleum industry is caused in the main by the influence of two powerful factors: (I) the physical growth in the demand for oils; and (2) the rising cost of drilling wells and constructing refineries, pipe lines, and other facilities. The segregation of these factors is accomplished by deflating the actual capital expenditures so that they are shown in terms of 1939 costs and then subtracting the adjusted series from the actual figures to yield a set of data representing the expenditures made on account of higher costs. Rising costs affect prices and the portion attributable to this factor had to be generated from the cash earnings of the industry, which called for higher oil prices. Introduction Capital may be defined as "wealth employed in or available for production." All production requires capital. Expanding industries require more capital than static ones, and technological industries employ more capital than. those in which little equipment is needed. The petroleum industry is both rapidly growing and highly technological, and, being a large industry, its capital requirements are prodigious, amounting to about one-seventh of the total of all American business, excluding agriculture.* Capital formation may be defined as the method by which the wealth or capital needed in the productive processes is created. There are various ways in which capital funds may be obtained but there is only one way in which capital can be created—out of production in excess of consumption, that is, savings. The physical realities are simple, but the monetary concepts are complicated because the mechanism of credit can draw upon future savings. Source of Capital Funds An industry, such as the petroleum industry, can obtain its capital funds from

Jan 1, 1949

By J. J. Gilman

WHEN a zinc crystal is immersed in liquid N, and then plastically bent, it is observed that it bends a certain amount and then fractures. This fracture occurs at a fairly reproducible radius of curvature, and the radius varies systematically with the crystal orientation. Because this phenomenon provides an unusually well-defined set of fracture conditions, it is possible to examine various possible fracture criteria and select the best one. Zinc crystals of various orientations were bent about axes lying in their glide planes (0001) and perpendicular to their glide directions [1210]. The crystals were 0.150 in. diam and had chemically polished surfaces. They were immersed in liquid N, while they were being loaded on an Instron testing machine. A three-point bending jig was used to load them. Table I lists the beam radius at which fracture occurred for each orientation. Each value is the average of at least six measurements. The normal stresses on the cleavage planes, at the time of fracture, were calculated as follows: First, from the fracture radius, R,, the orientation angle, x,, of the (0001) plane at the outer fiber was calculated. If x, = angle between the (0001) and the rod axis prior to bending, d = rod diameter, and X, = angle between the (0001) plane and a tangent to the bent crystal, then1 sinX, _ 2R, sin xn 2R, + d Since the glide shear strain is given by' y ' cot X, — Xo the glide strain at fracture, x,, can be calculated. Next, it is necessary to know the tangential stress in the outer fiber at fracture. This depends on the plastic flow curve, so a series of tensile tests were performed at —196°C on another set of zinc crystals. A curve of the average resolved shear stress versus glide strain was prepared. From this curve, shear stresses, r,, corresponding to the glide strains in the bend tests were taken. These values are listed in Table I. Then the normal stresses in the outer fibres, u,, were calculated from the relation U, = r, tan X, This analysis assumes that the fiber stresses in a bent beam are the same as the stresses in simple

Jan 1, 1959

By T. H. Alden

A correlation has been found in rock-salt structure single crystals between the latent hardening, measured by the direct stress activation of oblique slip systems, and the stress-strain behavior in simple compression. Materials with high latent hardening, like LiF, strain-harden at a low rate (Stage I) even when severely constrained. KCl, in contrast, shows low latent hardening and a tendency to strain-harden at a high rate (Stage 11). This correlation suggests that oblique slip is essential for Stage II hardening of these materials. THE role of secondary slip in the strain hardening of metal single crystals is a topic of lively controversy. On the one hand are theories in which secondary dislocations participate directly in Stage II hardening in the fcc metals, for example through the production of sessile dislocations,1 forest intersections, or jog formation. Much of the experimental evidence on which these theories are based has been reviewed by Clarebrough and Hargreaves.~ On the other hand, a recent theory5 denies that secondary slip has an essential role in Stage II hardening or in the transition from Stage I to Stage 11. In the latter view, Stage I is not terminated by an increase in the activity of secondary systems but by the exhaustion of undeformed material.6 The experiments reported in this paper will not resolve this controversy since the materials being studied are cubic ionic crystals rather than metals. However, the results do show in an unusual way a direct connection between "secondary" (nonortho-gonal or oblique) slip and strain hardening in these materials. Specifically, a correlation has been found between two independently measured properties, first the latent hardening of oblique (110)(1i0) slip systems as measured by direct stress activation of these systems, and second the stress-strain behavior at small strains. From prior work, it was known that in most cubi-cally oriented rock-salt structure crystals, two orthogonal slip systems operate and exclude the other equally stressed pair, oblique to the first pair.7'8 This observation apparently indicates that a significant interference exists between slip on oblique (110) planes and a relatively small interference between orthogonal (110) planes. The present experiments were begun with the intent of obtaining a quantitative measure of this difference by means of a study of latent hardening in these crystals. I) EXPERIMENTAL METHODS The experiments were basically of two types, first the determination of stress-strain curves by compression along a single (100) axis, and second the measurement of latent hardening by compressive prestrain along one cube axis followed by the determination of the yield stress in a second (latent) cube direction. All tests were done at room temperature in an Instron machine by compression between lapped, parallel steel faces. Three specimen shapes were used. For long crystals (nominal dimensions, 1/8 in. square by 1/2 in. long) the ends were lubricated with an oil-graphite mixture. Superior results with short crystals (about 1/8 in. cube) were obtained using 0.003-in. teflon film.' Thin crystals (1/4 in. square by 3/32 in.) were used for latent-hardening measurements and similar results were obtained with either lubricant. Test specimens were cleaved from Harshaw single crystals which had been irradiated to a dose of lo8 roentgen using a cobalt-60 source. The irradiation raises the yield stress and tends to prevent plastic deformation during sample preparation.10 Prior to testing, the irradiation hardening was removed by an anneal at 400°C. Ideal compression specimens have flat, parallel faces. In short specimens particularly, satisfactory results demand a close approximation to this ideal. In the present work, cleaved surfaces were often used directly as compression faces. The degree of success using this method depends on two factors: 1) the smoothness of cleavage faces, and 2) the extent to which the crystal is deformed or crushed by the chisel during the cutting of a long crystal into short pieces. Unfortunately, only one material of those studied, LiF, was completely satisfactory. NaF, NaC1, KC1, and KBr behaved less well so that

Jan 1, 1964

Book Review MANAGEMENT AND MEN. By Meyer Bloomfield, Boston. The Century Co., New York, 1919, pp. 584, H.X. 5 1/2. $3.50. This hook is an exposition of English efforts to solve the problem of labor unrest in England. The first six chapters are reprinted from articles published in the Satur-day Evening Post, for whom the author went to England to study the problem at first hand. These articles deal with housing, increased production, eliminating the internal friction in the industrial machine and a chapter each devoted to the view-point of employer and employee. These chapters are written in the easily readable magazine style and give a complete general survey of the particular solution being tried. Perhaps their greatest., certainly not their least, worth lies in the fact that they form a vehicle for unusually voluminous appendices containing in full the famous Whitley Reports which are the basis of the new movement, together with various reports, which, except for this publication, would be largely inaccessible to those inter-ested in this country. The Whitley scheme considers each industry a unit and proposes to establish therein a Joint Standing Industrial Council composed of representatives of employers and employees to consider appropriate matters affecting the industry at large. There is to be a District Council for each industry which will, as its name implies, deal with the clatters pertaining to that interest in. the particular district. The third and last body in this scheme of Industrial Parliament is the Works Committee, which is com-posed of representatives of the management and of the workers employed in particu-lar plants or mines to act in close cooperation With the district quid national machinery. The Whitley or similar schemes have been tried in many communities in England and the book contains interesting comments on the result obtained, it being notable that most of the objections conic from plants which have not tried the scheme. Meyer Bloomfield, the author; is the specialist in industrial personnel problems who organized the industrial service activities of the United States Shipping Board, Emergency Fleet Corporation. P. E. B.

Jan 10, 1919

By H. D. Merchant

NUMEROUS publications have examined hot hardness of metals and alloys. Some have studied creep in long-time hardness tests, few of which, however, were tested under a spherical indentor. 1-3 The results of Mulhearn and Tabor' indicate a parabolic-type creep for indium and lead, whereas Moore and Tabor2 how a logarithmic-type creep for indium. Similar semilog relationships between hardness and time have been found by Goffard and wheeler3 for magnesium, aluminum, and their alloys. In this note, the elevated-temperature hardness of some complex alloys, shown in Table I, was examined to discover whether any basic information about the deformation behavior of the alloys could be obtained. One of the alloys, H-13 alloy steel, was tested for short-time creep tests to examine the hardness-time relationship at various temperatures. A standard Brinell Hardness Tester, mounted with an appropriate furnace and 99 pct A12O3 poly-crystalline indentor, was employed for the purpose. The alloys were tested at temperatures from room to 1400°F for 30 sec under 1500-kg load. The creep studies were conducted for about 8500 sec at 7l°, 500°, 1000°, and 1200°F. For constants A and B, a relationship of the type H = Aexp(-BT) [ll was obtained for all alloys between hardness, H, and temperature, T. In the semilogarithmic plot, the data points for each alloy were arranged into two groups, each group on a straight line with a specific set of A and B values. These results are in agreement with many such observations on hot hardness, notably those of Westbrook for pure metals,4 The thermal softening coefficient, B, and transition temperature, Tt, for various alloys are shown in Table I. The change in slope around the transition temperature suggests an apparent change in the mechanism of deformation, probably from the shear (below Tt) to the diffusion type of mechanism. At the temperatures above Tt, for constants A' and B, a relationship of the type was obtained between H and T, Fig. 1. The nature of the equation, where R is gas constant, suggests the possibility of a thermally activated mechanism of deformation above Tt. The constant B' may hence be defined as the apparent activation energy of indentation. The B' values of various alloys are shown in Table I. A plot of B vs B' gives a curvilinear relation shown in Fig. 2. The indentation-creep data for H-13 alloy steel is shown in Fig. 3. At 71" and 500°F, the creep initially follows the logarithmic time law. However, the indentation size stabilizes after 7 sec at 71°F, and after 10 sec at 500°F. Further increase in loading time has no effect on indentation size. The creep of 1000° and 1200°F follows the logarithmic time law for the first 1000 sec, after which the

Jan 1, 1964

By C. Laird, C. E. Feltner

IN previous workif2 we have shown that the steady state cyclic stress response of pure copper tested in the low cycle fatigue range was determined only by the plastic strain amplitude and the test temperature. hus, copper, at any given temperature, has a unique cyclic stress-strain curve independent of prior history. Cu-7.5 wt pct Al, however, showed a stress response for a given plastic strain amplitude and temperature which depended sensitively on prior history. From this work we predicted that all wavy slip mode materials, typified by copper, would have a unique cyclic stress-strain curve; whereas all planar slip mode materials, typified by Cu-7.5 pct Al, would not. This prediction has now been tested for a number of materials of widely varying crystal structure and slip character. Wavy slip mode materials studied include: Fe. Al, Cd, disordered FeCo-V, and Cu-3 pct Co (quenched and aged). Planar slip mode materials investigated include: Fe-3 pct Si, ordered FeCo-V, disordered Ni3Mn, ordered Ni3Mn, and Zn. The treatment and properties of these materials are listed in Table I. Cyclic stress-strain curves were determined by controlled plastic strain tests (see Ref. 1 for details) at room temperature for all materials in both the initially annealed and cold worked conditions. The results obtained for iron and Fe-3 pct Si are typical of wavy and planar slip mode materials, respectively. The cyclic stress-strain curves for these materials are shown in Fig. 1 and it can be seen that iron has a unique cyclic stress strain curve while Fe-3 pct Si does not. Aluminum, Cu-3 pct Co, and disordered FeCo-V showed a behavior like that for iron, while Ni3Mn in both the disordered and ordered condition behaved in the same manner as Fe-3 pct Si. These results therefore support the general conclusion drawn in Refs. 1 and 2 that. for wavy slip mode materials, a cyclic mechanical equation of slate it =t.(hcp, i. T) is approximated in which the satura-

Jan 1, 1970

By Wm. Hamilton Merritt

IN this paper, which I have the honor to submit to the Institute, it is my intention to treat especially of that part of the North Staffordshire field which converges to a long tongue in the neighborhood of Congleton, and which includes the villages of New Chapel, Ford Green, Norton, Biddulph, Bradley Green, Gillow Heath, and the immediate vicinity. My object is not so much to give a minute description of the geology or systems of mining and smelting, as by a general review, some idea of the extraordinary facilities for the production of excellent iron, which have enabled this district to maintain its position more successfully than any of its rivals against the late depression in trade. The North Staffordshire coal field has the Cheshire and Lancashire fields some thirty-five miles to the north, those of Derbyshire and Nottinghamshire forty miles to the east, those of South Staffordshire and Shropshire, about thirty miles to the south, and the Denbighshire and Flintshire fields some forty miles to the west. It is highly probable that the coal continues under the new red sandstone to the Western and Southern fields as the dips on both sides, and absence of large faults, make it impossible to come to any other conclusion. In a section of this coal field, from Chatterly to Whitfield, thirty-two workable seams of coal are shown, of an aggregate thickness of 130 feet, varying from 2 feet 6 inches to 7 feet, and thirteen seams of ironstone, 24 feet, averaging from 2 to 4 feet. All of these seams have been minutely described in a paper by Mr. Charles J. Homer, read in 1875 before the British Iron and Steel Institute. In the northern part, to which I especially wish to direct your attention, the beds lie in a V-shaped basin, the underlying millstone grit and Yoredale rocks rising and forming escarpments on either side of the valley containing the coal. Throughout this district, at the outcrop of the coal, there are indications of old workings. A shaft 4 to 5 feet in diameter reaches the coal at about 14 yards from the surface, and from it the coal has

Jan 1, 1880

By William Hamilton Merritt

In this paper, which I have the honor to submit to the Institute, it is my intention to treat especially of that part of the North Staffordshire field which converges to a long tongue in the neighborhood of Congleton, and which includes the villages of New Chapel, Ford Green, Norton, Biddulph, Bradley Green, Gillow Heath, and the immediate vicinity. My object-is not so much to give a minute description of the geology or systems of mining and smelting, as by a general review, some idea of the extraordinary facilities for the production of excellent iron, which have enabled this district to maintain its position more successfully than any of its rivals against the late depression in trade. The North Staffordshire coal field has the Cheshire and Laucashire fields some thirty-five miles to the north, those of Derbyshire and Nottinghamshire forty miles to the east, those of South Staffordshire and Shropshire, about thirty miles to the south, and the Denbighshire and Flintshire fields some forty miles to the west. It is highly probable that the coal continues under the new red sandstone to the Western and Southern fields as the dips on both sides, and absence of large faults, make it impossible to come to any other conclusion. In a section of this coal field, from Chatterly to Whitfield, thirtytwo workable seams of coal are shown, of an aggregate thickness of 130 feet, varying from 2 feet 6 inches to 7 feet, and thirteen seams of ironstone, 24 feet, averaging from 2 to 4 feet. All of these seams have been minutely described in a paper by Mr. Charles J. Homer, read in 1875 before the British Iron and Steel Institute. In the northern part, to which I especially wish to direct your attention, the beds lie in a V-shaped basin, the underlying millstone grit and Yoredale rocks rising and forming escarpments on either side of the valley containing the coal. Throughout this district, at the outcrop of the coal, there are indications of old workings. A shaft 4 to 5 feet in diameter reaches the coal at about 14 yards from the surface, and from it the coal has

Jan 1, 1880

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y', and E carbonitride has been confirmed and it has been found that y' is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part' reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,' this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* 'Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By Dr. Egleston

While I thoroughly appreciate the United States testing-machine at the Watertown Arsenal, and regard it as the most accurate testing-machine that has yet been built, I wish that I could say that it is complete in all respects. I not only fully appreciate it, but I have given up advising thesending of material to be tested anywhere else. It is five or six times more expensive to use this machine than any of the others, but the results which are obtained from it are, I think, perfectly reliable, and of such a character that the tests are all comparable with each other. It has proved, beyond a doubt, that the system of testing specimens of' diminished area, and then calculating that the metal examined will be as many times stronger as its area is greater, is an absolutely vicious one. I am quite prepared to say, that, either from their limited size or faulty construction, most of

Jan 1, 1882

By William E. Ford, Edward Salisbury Dana

The aluminate, ferrates, etc., allied chemically to the borates, have been already intro- duced among the oxides. They include the species of the Spinel Group, pp. 418-423, also Chrysoberyl, p. 423, etc. SUSSEXITE. In fibrous seams or veins. H. = 3. G. = 3.42. Luster silky to pearly. Color white with a tinge of pink or yellow. Translucent. Index, 1.59.

Jan 1, 1922

By B. F. Zwick

The entire production of oil in Ecuador so far has come from the Santa Elens Peninsula, Province of Guayas. Both the shallow fields of the northern and the deeper fields of the southern part of the peninsula have been in constant exploitation, though the former are of doubtful economic value. In Table I herewith, which commences with the total amounts produced by the various companies up to 1940, annual company totals are given for the succeeding years. The figures for 1944 have been partly estimated. Table 2 gives figures on casinghead gasoline. Shell Company of Ecuador (formerly known as Anglo-Saxon) has continued active exploration in the Oriente region east of the Andes, and during 1944 the Company's first wildcat well was spudded in. International Ecuadorean Petroleum Co. (formerly International Petroleum Co., Limited) has pursued an active exploration campaign since the latter part of 1939, and a drilling string was placed in operation about a year later. A second string of tools was added during 1943 and a third a few months ago. Ten wildcats, all dry, have been completed in this period, two wells are drilling at the present time and other locations are on the program. Seven of the wells thus far drilled are in the area between Guayaquil and the Santa Elena Peninsula, one up the Daule River beyond Balzar, one on Puna Island in the Guayas Estuary and one in the northern province of Esmeraldas. Both the present drilling wells are in the Guayaquil-Santa Elena zone. The situation in regard to concessions has changed during the past four years because I.E.P.C. has made its selections from the extensive Daule-Guayas Study Concession, as a result of which large tracts were returned to the Government; because of the expropriation of the holdings of the "Ecuapetrol," a German concern whose acreage has passed into other hands; the Peruvian-Ecuadorean boundary settlement, which has reduced Shell's holdings somewhat; and the transfer of most of the holdings of the Cia. Minero-Petrolera del Pacifico to I.E.P,C. The greater part

Jan 1, 1945

G. K. BURGESS, ? Washington, D. C.-At the Bureau of Standards it was decided, in order to study the high-aluminum end of these curves, that efforts should be made to prepare pure aluminum, and the promise of getting aluminum, practically free from the two elements that have such great effect in very small quantities, namely, silicon and iron, and which

Jan 12, 1919

By W. A. Backofen, M. L. Ebner

SINCE the early work of Gough with Hanson and Wright,l-3 the study of fatigue has been characterized by experiments on single crystals only in recent times.9-10 Now, increasing attention is given to this aspect of fatigue research for the insight that it may provide into details of mechanism. The investigations have concentrated to a large extent on the development of deformation markings on fatigued crystals, and have shown the cracks to originate in slip bands possibly preceded or accompanied by slip-band extrusions. Experiments of special interest to the present work were conducted by paterson5 on copper crystals and involved both metallographic examination and measurement of change in flow stress. Crystals were cycled in alternating tens ion-compress ion with a constant plastic shear-strain amplitude of approximately 0.8 pct, and were particularly revealing for their demonstration of hardening with accumulated strain similar to that in unidirectional straining, through an easy-glide stage I followed by a stage II of rapid hardening; deformation was not continued beyond 40 cycles, however, so that the eventual course of the hardening curve could not be decided. For the conditions used by Paterson, surface slip markings were similar to those observed in unidirectional straining, but there were no X-ray asterisms and no deformation bands on the surface. In current thinking about the nature of fracture in fatigue, two views relative to mechanism are generally acknowledged, with the reservation that both could apply simultaneously in some measure. As one possibility, fracturing across a slip plane is regarded as a result of loss of cohesion from the creation of many point defects by dislocation movement under the cyclic loading.'' On the other hand, fracture has also been taken to follow as a consequence only of the geometry of slip at a free surface, consisting of offsets and crevices which eventually become fatigue cracks.12, l3 The work of McCammon and Rosenbergl4 showing fatigue in polycrystals at 4.2oK makes clear that any long-range diffusion of point defects is unnecessary, yet studies such as those of Forsyth and stubington15 show that accelerated diffusion may be a characteristic of deformation under fatigue loading. Interest in obtaining data of possible use for resolving such questions led to the experiments described below. Copper crystals were conveniently loaded in alternating four-point bending at constant deflection, a test condition shown to approximate a constant plastic strain amplitude for a wide range of axial orientations. The method of testing was not readily adapted to extensive study of temperature effects, but an investigation of the geometry of crack formation could simply be made by orienting,the slip direction at different angles to the surface. EXPERIMENTAL PROCEDURES Single crystals were grown by a modified Bridgman method in a stationary gradient furnace under an atmosphere of purified dry nitrogen. Purity of as-grown crystals was 99.999 pct as determined by spectrographic analysis plus vacuum fusion and gravimetric analyses for oxygen and sulfur, respectively. Crystals were of reasonable perfection as evidenced by a critical resolved shear stress at 10 deg from (110) of 60 g per sq mm and half-width of a (400) X-ray diffraction line from one crystal of

Jan 1, 1960

By Waldemar Lindgren

The important investigations of Dr. G. F. Becker at Steamboat Springs, Nev., in 1885, aided by the analytical work of W. H. Melville, established the fact that sulphides were being deposited at the surface by hot ascending waters.' Steamboat Springs is situated near the eastern base of the escarpment of the Sierra Nevada, six miles distant from the Comstock lode.

Jan 1, 1906