Search Documents

By W. B. Mather

R. G. Wuerker (University of Illinois, Urbana)—Mr. Mather is to be congratulated for stressing the most urgent need for a program of testing the physical properties of rocks, as they are encountered by the petroleum engineers on their drilling jobs and by the miners on their excavating, roof control and mineral preparation tasks. Another valuable source of information is the Handbook of Physical Constants.22 It stresses the physicist's approach rather than the engineer's procedure. The study of hardness, and rock hardness in particular, is beset with many difficulties. There is no satisfactory definition of hardness yet, and the term hardness is used to describe a number of quite dif- ferent properties. Hardness tests are grouped into static and dynamic determinations. They should be expressed with reference to the mechanical action of the applied force, like indentation hardness, scratch hardness, abrasion hardness, rebound hardness. A discussion of all these various hardness tests and of the special difficulties encountered in hardness testing of such heterogeneous material as rocks is given in the U. S. Bureau of Mines' standard proposal. The more critical student may be referred to the book by D. Landau: Hardness, which is in my opinion the best existing treatise on this subject.

Jan 1, 1952

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By Leo Ranney

ANY years ago a prospector came to a Nevada town and built himself a shack. Day after day he searched the hills for gold -but he found none. He closed his shack and hurried north, where a strike had been made. Next he tried to trap the flour gold that floats down the Snake River. He panned the black sands along the Oregon coast. He ranged over the mountains and up the gulches of far-off Alaska. At last, broken in health, six years ago he came back to his old home in Nevada. There his shack still stood-nobody wanted it. One day he started a garden in the rocky soil that he owned. His spade turned up a chunk of quartz, and in that quartz were stringers of gold. He had found a rich gold vein, running right under his own house. You gas producers who have hurried to Oklahoma, Louisiana, East Texas, South Texas, West Texas, even to California to drill wildcat holes a mile or two miles deep-why not, like the old gold prospector, have a look in your own back yard? Some of your coal seams contain 20,000,000 cu. ft. of natural gas per acre.

Jan 1, 1943

By Leonard A. Wood, A. G. Winslow

Subsidence has occurred in several areas of the upper Gulf Coast region of Texas, although in most cases this is not evident without precise instrumental leveling. As referred to in this report, the region com- prises about 7200 sq miles of the Gulf Coastal Plain and includes all or parts of the following counties: Harris, Fort Bend, Waller, Brazoria, Galveston, Liberty, Chambers, Orange, and Jefferson (Fig. 1 ). Topographic relief is low, ranging from sea level at the Gulf of Mexico to 300 ft or more in northwestern Harris County.

Jan 10, 1959

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, .went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the blast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success ,is made of wrought-iron tubes, 2 1/2 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglomerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

Jan 1, 1873

By G. Wakefield, A. H. Daane, D. H. Dennison, F. H. Spedding

Preparation of pure scandium metal was accomplished by calcium reduction of the fluoride by two methods; a low-temperatzdre alloy process and direct reduction with subsequent distillation of the product. The following properties were determined: melting point: 1181OK; boiling point (calculated): 3000°K; lattice constants at 298°K (hexagonal lattice): a = 3.308 * 0.001 A, c = 5.267 * 0.003A; calculated density at 298°K, g per cm3: 2,990 + 0.007; electrical resistivity, ohm-cm: 299°K, 66.6 ± 0.2 x 10 -6; 373oK, 77.4 * 0.2 x 10 -6; thermal coefficient at 299°K, ohm-cm per deg: 5.4 X x; heat of sublimation at 298°K, kcal pel- mole: 80.79. The vapor pressure was determined as a function of temperature between 1505o and 1748°K, with the data fitted to a straight line shielding the equation: Log Pmm = -1.718 X 104/ToK + 8.298. SCANDIUM, element number 21, was first discovered by Nilson in 1879 and was recognized as the Ekaboron as predicted by Mendeleff. As it is in group III of the periodic table, the general properties are a little like aluminum and also resemble quite closely the properties of yttrium and the rare-earth metals, in both the metallic and ionic form. Although the earth's crust contains approximately 5 ppm of scandium (the element is as abundant as arsenic and twice as abundant as boron) it generally occurs so widely distributed that it has earned the reputation of being very rare. The one exception to this is the mineral thortveitite, which has been found in Madagascar (20 pct Sc2O3) and in Norway (35 pct Sc2O3). Scandium also occurs in small but distinct amounts in uranium and rare-earth ores; the recent larger scale processing of these materials has made some scandium available from these sources. As with other naturally-occurring monoisotopic elements (except Be), scandium contains an odd number of protons and an even number of neutrons. Scandium metal was first prepared by Fischer and coworkers1 in 1937 by electrolysis of scandium chloride in a molten eutectic mixture of lithium and potassium chlorides, using molten zinc as a cathode and collector of the scandium metal produced. The zinc was removed from the Zn-2 pct Sc alloy by vacuum distillation, leaving a product reported to be 94 to 98 pct Sc, with the main impurities being iron and silicon. They reported a melting point of 1400° C for this material. Scandium has also been prepared by the reduction of scandium chloride with potassium metal in a glass apparatus by Bommer and Hohmann in 1941,' resulting in a mixture of metal and potassium chloride; these workers did not isolate the metal proper, but the X-ray diffraction of the slag-metal mixture showed it to be hexagonal with a = 3.30A, c = 5.45A. petru3, 4 and coworkers have recently reported the preparation of the metal in a compact form by the reduction of either ScF3 or ScC13 with calcium metal and subsequent distillation of the product. This process probably yielded a metal of high purity, but they list no chemical analysis nor do they list any of the properties of their product. Previous related work in this Laboratory has been concerned with the production of yttrium and the rare-earth metals and the determination of their physical properties. Because of its similarity to these metals, scandium is being included in this study. PREPARATION OF SCANDIUM METAL The preparation of yttrium and the rare-earth metals may be accomplished by reduction of their fluorides with calcium metal in tantalum crucibles.5 This process leads to the introduction of tantalum (up to 0.5 pct) as an impurity in the higher melting rare earths, but since the tantalum occurs as dendrites, uncombined with the rare-earth metals, its presence is not objectionable in some cases. The preparation of scandium metal in this manner, however, was found to yield a product containing 2 to 5 pct Ta. To obtain a purer product, the following two methods were developed for the reduction of scandium fluoride with calcium metal: i) a low-temperature process utilizing zinc to form a low

Jan 1, 1961

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author's reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

By M. J. Taffanel

I AM very much impressed by this manifestation of international brotherhood; the mining engineers on both sides of the ocean have similar subjects to deal with, meet with the same difficulties, expose themselves sometimes to similar dangers; they are like companions in arms in the battle fought by mankind in order to subjugate the natural forces and to draw profit therefrom. There is no other field where this fraternity must manifest itself more actively than in the studies pursued with a view to improving the safety of mines and to rendering impossible in the future these mining disasters, which every year claim hundreds of victims. These are very difficult problems, the solution of which requires numerous and laborious experiments accompanied by very arduous scientific investigations; it is extremely desirable that the various mining countries, which have undertaken to solve these difficult problems, should unite their efforts in order to succeed as soon as possible and as well as possible. This idea has been fully grasped by your Bureau of Mines, which has brought me to Pittsburg; the daily exchange of views with the distinguished chief of-the mine investigation division, George S. Rice, and with his excellent collaborators, the comparison of the results obtained at Lievin and Bruceton, the checking of these results by means of new tests, the profound study of the measurements, diagrams, measuring and laboratory apparatus, the cooperative investigation of new apparatus, or the preparation of new investigations, are, I hope, of such a nature as to bring about great progress. I think that it will be interesting to you to know what has been done in France along this line.

Jan 9, 1914

FREDERICK G. BRENNEMAN Frederick G. Brenneman died of pneumonia at his home at Pottsville, Pa., on November 24. He was in the class of 1912, of the Pottsville High School, attended Bellefonte Academy, and graduated from the Colorado School of Mines, at Golden, Colo., in 1916. He is survived by his parents, Mr. and Mrs; Philip Brenneman and three brothers, Louis P. and Robert C. at home, and John :F., of Camp Merritt, N. J. Mr.

Jan 1, 1919

By C. C. Templeton, J. C. Rodgers

A key step in feed water treatment for generating wet steam for thermal oil recovery is the removal of calcium and magnesiunt hardness by cation-exchange series softening. Knowing the solubility of any scale forming salts in brines at elevated temperatures is necessary for fixing the level to which the feed water must be softened. Such calcium sulfate solubility data, previously not available above 392F, were determined by the authors in a flow equilibrium apparatus mud will be reported elsewhere. These data were used to develop a method for predicting the solubility of anhydrite in hot water or steam droplets for saturated steam pressures as high as 2,000 psig (637F). (The calcium sulfate solubility product is represented by a combination of two factors, one reflecting the effects of ionic strength and the other accounting for the effects of complex ion formation in either calcium-magnesium-rich or sulfate-rich brines.) The method is applied to a calcium-magnesium-rich brine If moderately high salinity from a pilot hot-water flood, I nd to several sulfate-rich, low-salinity feed waters and l lowdown (cooled steam droplets) samples from steam s ak operations. The predicted calcium hardness levels corresponding to the calcium sulfate solubilities agreed reasonably well with the results of laboratory solubility determinations run on the field samples. Further testing of the method is needed for brines of other composition classes. Existing field cation exchange softeners in the cases tested are performing adequately since all the samples were found to be undersaturated with respect to calcium sulfate at their operating temperatures. Introduction Prevention of scaling caused by precipitation of calcium sulfate (anhydrite) is of considerable concern in connection with thermal recovery processes using wet steam or hot water. To avoid anhydrite precipitation in a heated system, an engineer must keep the product of the calcium and sulfate concentrations in the water or steam droplets below the value of the solubility product of anhydrite for the temperature and brine composition in question. Usually it is most practical to keep the concentration product lower than the solubility product by keeping calcium low in the presence of high sulfate, or by keeping sulfate low in the presence of high calcium. This can be done by a choice of combinations of natural waters and water treatment processes (such as series cation exchange softening to remove calcium). Until recently, few anhydrite solubility data, particularly for solutions containing other salts, were available for temperatures above 392F (211 psig steam); Marshall, Slusher and Jones' studied the CaS0,-NaCI-H,O system up to 392F and surveyed the work of previous investigators. To model natural brines, one needs to study the solubility of anhydrite in aqueous solutions of sodium chloride, sodium sulfate, calcium chloride, magnesium chloride and their mixtures. Since steam pressures as high as 2,000 psig (637F) may be involved in thermal oil recovery projects, a solubility study was conducted between 482 and 617F.' Discussed in this paper is the application of these data to the prediction of anhydrite precipitation in some practical steam soak and hot-water injection projects. Any simple method for predicting the solubility of an inorganic compound over a wide range of temperatures and solution compositions must be based on some assumptions, and therefore must yield approximate results. On the one hand, natural brines contain too many ionic species for all to be included in a simple scheme; on the other hand, there is no adequate theoretical basis for the exact prediction of solubility in even simple solutions of mixed electrolytes. However, it is possible at a given temperature to base a reasonable prediction scheme on two phenomena:'-' the increase in solubility with increasing total concentrations of all ions (as measured by the ionic strength; see the Appendix), and an increase due to formation of cornplexes between calcium ions and sulfate ions and between sulfate and magnesium ions. Stiff and Davis' developed such a scheme for predicting the solubility of gypsum (CaSO, ¦ 2H,O) in brines at temperatures u~ to 212F. However, for the higher temperaturei of present interest, the stable solid phase is anhydrite (CaSO,). This study involves a two-part method for predicting anhydrite solubility products. First, one predicts a value K, for a given ionic strength I and a given temperature T corresponding to mo./msr, = 1 from data of the CaS0,-NaCI-H,O system. Second, one determines a group of factors F .= F(Ca) • F(Mg) • F(SO,), where the individual factors account for increases in the solubility product due to complex formation by high concentrations, respectively, of calcium, magnesium and sulfate. Combining the two parts, one obtains the solubility product in molalities as

Jan 1, 1969

By C. A. Stewart

PAGE. I. Introduction............ 241 II. Location. TopoGRaphy. and History....... 243 III. DescRiption of the Rocks......... 245 1. Altered Sediments.......... 245 2. Alaskite........... 246 3. Alaskite.Porphyry.....255 4. Quartz Dikes........... 257 5. Biotite.Granite.......... 256 6. Quartz.Porphyryl......... 260 7. Andesite........... 262 8. Miscellaneous Dikes......... 263 IV. Age oF the Rocks and Comparison with other Localities.. 263 V. AlteRation............ 265 1. Sericitization........... 265 2. Silicification........... 266 VI. StRuctuRes........267 1. Dip of the Limestone......... 267 2. Faulting........... 267 VII. Contact - metamorhism,.......... 269 1. Endomorphism.......... 269 2. Exomorphism......... 271 Recrystallization and Loss of Color...... 271 New ,Minerals.......... 272 Addition of Material........ 274 Volume.Changes.... 276 Locus of Metamorhism........ 277 Method of Precipitation.........278 VIII. ORe-Deposits............ 278 1. Contact-Metamorphic Copper.Ores,..... 279 General..........279 Shape and Distribution........ 279 Minerals........... 281 Secondary Enrichment........ 282 2. Disseminated Copper.Ores........ 283 3. Origin of the Copper.Orcs........ 284 4. Lead-Silver Ores.......... 287 IX. Bibliography............ 288

Jan 1, 1913

By H. K. van Poollen, H. C. Bixel

A treatment is given of the transient pressure behavior of a well located at the center of a circular region surrounded by a radial discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility and porosity are uniform but may be different from those on the other side of the discontinuity. The results are obtained by solving a pair of finite difference equations. The numerical solution to these equations is obtained using a digital computer. The results are compared with previously published, approximated analytical solutions to the same problem. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables studied include dimensionless time from '0.001 to 100 and storage capacity ratio from 0.001 to 1,000. The well behaves as if it were in an infinite reservoir for dimensionless times less than 0.25. Reservoir properties near the well can be estimated in the usual manner. An overlay technique is used to match an experimental curve with one of the theoretical curves. It is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time tD at which a match occurs into the equation a = (0.000264 tk1/tD , µ1 cI)I/2 where kI/ I µI cI is the diffusivity near the well, and may be estimated from data taken at early time. Several buildup curves are computed. These curves show that for early shut-in times, correct values for transmissibility are obtained from conventional analysis. However, erroneous values of static reservoir Pressure are obtained unless data at large shut-in times are taken. INTRODUCTION A mathematical treatment of the transient pressure response of a well located at the center of a region bounded by a circular discontinuity is given. Within a region (Fig. 20) the properties of both the rock and the fluid are considered to be constant on either side of the discontinuity. While these properties are considered constant, they may be different on opposite sides of the discontinuity. A discontinuity of this type could be a fluid-fluid contact or a sudden change in rock characteristics such as thickness, porosity or permeability. Analytical solutions to this problem are available. 1-3 However, they are so involved that they are of little practical use. An approximate solutionl is available but the range of times over which it is valid has not been specified. A numerical solution to a pair of finite difference equations is used to obtain the solution given in this paper. PREVIOUS WORK One of the first solutions to the problem was published by William Hurst.1 Hurst considered unsteady-state flow of fluids through two sands in series with different mobilities in each sand. He used Laplace transforms to obtain a solution for a single well located at the center of the circle enclosing the first of the two sands. In this case, the solution for the pressure change in Region I (Fig. 20) is2

By J. W. Schroeder

SEAMLESS pipe, the product produced from piercing a solid round billet of steel by the Mannesmann process, was first produced in the latter half of the 19th century, the Mannesmann machine having been patented in 1885. The products of other processes also have been termed seamless pipe; for example, the cylindrical section produced by "cupping," which consists of forming a cup from a flat plate or disk and further elongating the cup into a tube by passing it through a set of reducing dies. The purpose of this paper is to discuss some of the more important metallurgical factors and their relationship to the economical production of seamless pipe produced by the Mannesmann piercing process. The first seamless tube plant in America was established at Shelby, Ohio, in 1891, and was employed in the manufacture of bicycle tubing. For a number of years the bicycle industry was the only user of seamless tubing, and this tubing was produced by hot-rolling pierced billets imported from Europe and finishing on the cold drawbench. At the turn of the century, the automotive industry was responsible for an increase in the demand for seamless tubing. The growth of this industry was the dominant factor leading to the phenomenal growth of the petroleum industry, which in turn created a tremendous demand for seamless pipe. In addition; the old lapweld iron boiler tubes for stationary and locomotive boilers were replaced gradually by seamless tubes. Since 1929, the production of seamless steel pipe and tubes has increased over loo pct. In 1929, 1,459,9031 net tons of seamless pipe was produced, including both hot-finished and cold-drawn material, as compared with 3,087,3122 net [ ] tons in 1948. Table I gives the distribution of seamless pipe by classes for 1948. METALLURGICAL PROBLEMS From a metallurgical standpoint, the production of seamless pipe has presented many problems. Practically every type of steel, carbon and alloy, with the exception of the superalloys developed during World War II, has been pierced and rolled successfully into tubing. This includes bessemer, open hearth, by the stationary and duplex processes, and electric steels. The range of sizes produced is no less staggering to the imagination, when it is considered that the hypodermic needle, which is 0.016 in. diam with a wall thickness of 0.004 in., and pipe for gas or oil transmission lines, with a 26 in. OD, are both seamless tubes. Between these extremes, the range of diameters and wall thicknesses meets most present-day demands for seam-

Jan 1, 1951

By AIME AIME

SOME 65 members of the Institute, including most of the Local Section delegates and several Directors and officers, were on hand for the Annual Business Meeting of the Institute held in the Engineering Societies Building on Monday, Feb. 21, at 4:30 p.m., immediately following the second session of the Local Section Delegates Conference. President Mathewson presided. The meeting was largely taken up with the presentation of committee re- ports, discussion of which was invited. F. E. Wormser presented the report of the Admissions Committee ; Philip Kraft, Papers and Publications Com-

Jan 1, 1944

By Walter R. Hibbard, George H. Eichelman, William P. Saunders

INTEREST in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,1 has resulted in the application of similar heat treatments to other eutectoid transformations. Studies2.3.4 of the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5,6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported' as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. PREPARATION OF ALLOYS The copper-silicon alloy equilibrium diagram is shown in Fig I. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutectoid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct). Smith5 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.7 Following the casting techniques of Krynitsky, Saunders and Stern,8 the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under the melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X ¾ in., was annealed at 750°C for 21 brand furnace cooled. About 1/16 in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. methods.9 The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1948

SULPHUR is a very well known mineral and apparently is produced in many places. It is engendered from an unctuous earthy and powerfully hot substance so that it is considered among experienced workers to bear a resemblance to the element of fire. This is called by these same men the masculine seed and the prime agent of Nature in the composition of metals. Because of its great dryness and heat it has, as experience shows, affinity with fire, which is easily introduced in it when brought near. And once introduced the fire is quenched only with difficulty before its unctuousness is wholly consumed. Although it shows itself to us of such a hot and dry nature, we must not think that sulphur is a substance so pure that it can stand by itself or that in order to attain its form it has no need of its portion and part of moisture like every other mixture. This is shown to us by its easy fusion, in which it resembles the metals. This thing is found in many places and in many varieties of color; some are white, others yellow and orange, and some others between gray and black. They also say that some red is found. It does not occur in that arrangement of veins like other minerals, but most liberal Nature makes whole mountains of it as is seen in the Aeolian islands, [26] near Sicily, in Etna or Moncibello which is the island of Sicily, at Pozzuoli, in the territory of Rome, in the Sienese domain at San Filippo, and in many other similar places. It is a substance that has a very strong odor and is most unpleasant to smell. It is very fixed in its substance so that it is never corrupted by time, by boiling, or by the moisture of water. For although it may stand in water a long time it never becomes soft nor does it ever decrease or increase in weight. It is brittle and easily crushed very fine. It is said that a trace of garlic rubbed on the mortar helps anyone who wishes to reduce it to impalpability. Its ores have a form more like earth than like stone although they some¬times have the color of a certain soft rock. The places where it is found are easily recognized by the great odor that they give out and by the very hot baths that often spring forth near it. What I have already told you about quicksilver that is contrary to the

Jan 1, 1942

By Claus G. Goetzel

PRESSING of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal [ ] friction. As long as curved surfaces, recesses, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more difficult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB). Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. VARIABLE FACTORS IN MOLDING POWDERED METAL PARTS Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2 : I would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only I.5, a compression ratio of 5:I would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1945

By Arnulf Muan, Klaus Schwerdtfeger, L. S. Darken

The equilibrium ratios CO/CO, of. a gas pharse coexislitrg with selected oxide phase assemblages of the system "FeO"-MnO-SiO2 and metallic iron have been determined at 1150°C. The data obtained are combined wilh the thermodynamic data on fayalite (Fe2SiOi) and "FeO"-MnO solid solutions to derive the actiuity-coiHpQsiUon relations for the various oxide components of the olivine (Fe2SiO4-,lIn2Si04) and pyroxenoid (standard free energies of formation of ferrosilile (FeSiO,), tephroite , and rhodonite from their oxides have been evaluated. In the Appendicc~s by Darken and Schivcerdtjeger the ideal solution law for solid deri oed. THE quaternary system Fe-Mn-Si-0 is of interest in many important phases of iron- and steelmaking. For instance, reduction in the blast furnace of ores containing Fe-Mn silicates, deoxidation of liquid steel with Mn-Si alloys, formation and subsequent alterations of oxide inclusions in steels, and the oxidation of manganese- and silicon-containing steels during processing are all governed largely by the thermodynamic relations existing in the system Fe-Mn-Si-O. Although the equilibria between liquid iron and Fe-Mn silicates have been studied in detail previously,' experimental data are lacking for equilibria among the solid phases. The present paper provides such data for a selected temperature, 1150°C. I) PREVIOUS WORK The general feature of subsolidus phase relations in the system iron oxide-manganese oxide-silica under strongly reducing conditions is known.' Fig. 1 represents an isothermal section at 1150°C. The phases present, in addition to silica, are three solid-solution series, viz.. the oxide solid-solution series "Fe0"-MnO (manganowiistite), the orthosilicate solid-solution series Fe2SiO4-Mn2SiO4 (olivine), and the metasilicate solid-solution series FeSi03-MnSi03 (pyroxenoid). The "FeO"-MnO solid solution is continuous between the two end members wustite and manganositeV3 as is the orthosilicate series between the two end members Fe2SiO4 and Mn2 SiO4. 4 The metasilicate solid solution, on the other hand, extends only part way from the MnSi0.l end member toward FeSiO because the latter end member is unstable relative to the phase assemblage fayalite + silica. The letters a through m in Fig. 1 identify end members of the individual solid phases dealt with [for instance, c designates fayalite (FeZSiO4) in equilibrium with wustite, e designates fayalite in equilibrium with silica, and so forth]. In addition to the phase relations there are some thermodynamic data available for the end members of the silicate solid solutions and for the "FeO" -MnO solid solution. The free energy of formation of fayalite (Fe2Si04) from its oxide components has been studied by several investigators. Unfortunately, the data obtained show considerable discrepancies. According to recent tabulations by Kelley, the change in standard free energy Affn for the reaction

Jan 1, 1967

By Edward W. Parker

At the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899,I presented a paper on this subject entitled, Coal-Cutting Machinery,' which has become somewhat out of date, in view of the decade's development in this feature of the coal-mining industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is "shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the U. S. Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent. in 1907 to 37 per cent. in 1908. In 1898 only 19.5 per cent. of the total product was unclercut.by the use of machines. The number of in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 mas almost exactly double that of 1898, while the machine-

Jan 1, 1911

By H. T. Kennedy, S. M. Avasthi

An equation developed for gaseous hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 0.73 percent when applied to 264 natural gas and condensate systems including 2,043 PVT points. Another equation developed for liquid hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 1.12 percent when applied to 346 crude oil systems including 1,759 PVT points. Both equations require composition of the mixture to be expressed as mole fraction of methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide, together with the characteristics of the heptanes-plus fraction in addition to the temperature and pressure. The equations cover wide ranges of the variables involved, and their accuracy is considerably better than that of other available methods. The equations were differentiated to allow calculation of the coefficients of isothermal compressibility and isobaric thermal expansion. (In this paper the coefficient of isothermal com-pressibility and the coefficient of isobaric thermal expansion will be expressed as compressibility and thermal expansion coefficient, respectively.) Equations to calculate these quantities are presented. INTRODUCTION Calculations of reservoir performance for petroleum reservoirs require accurate knowledge of the volumetric behavior of hydrocarbon mixtures, both liquid and gaseous. Compressibilities are required in transient fluid flow problems, and thermal expansion coefficients are important in thermal methods of production. An accurate laboratory investigation of the PVT behavior of each reservoir fluid encountered would be costly and time consuming. For this reason various correlations for predicting fluid properties have been developed and recorded in recent literature. Correlations have been presented in the form of graphs, tables and equations. Since an increasing number of studies are being conducted with the aid of electronic computers, recent efforts have been directed toward development of correla-tions suitable for computer programming. Application of computers permits the use of more complex correlations which otherwise are not feasible. Moreover, methods for predicting reservoir performance, particularly those based on the compositional material balance, depend upon the capability of accurately expressing the molal volumes and other fluid properties as functions of pressure, temperature and composition. The coefficient of isothermal compressibility c is defined by

Jan 1, 1969