Search Documents

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as follows: 1 Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimen¬sion of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of Water 1. A particle will move upward if [W > KVr(s-1)] and, by suitably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [T1= s2-1] cannot be separated in an upward-current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of 2.5 sp. gr. Unless 2.5-1 the ratio of diameters is less than [1.35-1 or 4.3 to 1,] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone¬-shaped vessels or vessels of other shapes that allow the use of&apos; different velocities of current at different points in the flow are used to modify this limitation. 3. During the initial stages of motion, coal particles ascend more rapidly than refuse particles of the same size. 4. A particle will ultimately fall if [W < KVr(s-1).] If particles of

Jan 1, 1950

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard&apos;s and Dundrova&apos;s theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.&apos; In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

By W. T. Roberts, N. G. Turner

A study of the fatigue properties of several grades of commercially pure titanium has established that the strain-aging process is of minor importance in the development of a fatigue limit and a relatively high fatigue strength ratio. Metallographic observations and damping measurements at room temperature indicate that striations are able to spread from grain to grain only at stress levels above the fatigue limit. This suggests that the fatigue limit represents the stress above which large-scale dislocation unlocking takes place. Fatigue tests on annealed material at - 60" and - 196" c showed that under conditions when a thermally activated diffusion process would be suppressed the fatigue limit is not eliminated. Prestraining at room temperature did not have a detrimental effect on fatigue strength at room temperature but a decrease was recorded at — 60°C. This is further evidence that initial dislocation locking is a important strengthening mechanism. TITANIUM and titanium alloys have S-N curves with a definite fatigue limit, and a high ratio of fatigue limit to UTS can be attained. Other materials which show similar fatigue characteristics are mild steel and some Al-Mg alloys. The fatigue limit of these materials has been associated with their strain-aging capacity. It is well-known that commercial-purity titanium contains interstitial impurities which can give rise to a sharp yield point, and a small strain-aging effect following static strain has been demonstrated.7 This type of aging reaction is differentiated from the dynamic aging process when aging occurs during plastic deformation, and which is generally observed at elevated temperatures. In a titanium at room temperature, dislocation locking is associated with the interaction of interstitial oxygen, nitrogen, and carbon atoms with dislocations. Ehr-lich has shown that the distortion produced by introduction of these atoms into the hcp lattice has no shear stress component and hence there is no interaction between the stress field and the screw component of a dislocation. Thus the dislocations as a whole are only weakly locked. It is clear that strain-aging effects in hcp a titanium will be much less pronounced than those observed in bcc iron and steel. In recent years, the attribution of the fatigue limit solely to strain aging has been questioned. It has been pointed out that a definite fatigue limit is observed at temperatures as low as -196°C in some titanium alloys,&apos; and strain aging is not expected to be effective at this temperature. The role of initial locking of dislocations in determining fatigue behavior has been examined in low-carbon steel by Oates and Wilson. They showed that under conditions in which the aging potential is low the factors which control the buildup of local stresses and hence affect dislocation unlocking, e.g., grain size, are important. There are indications that other metals can have a definite fatigue limit with no established strain-aging capacity, an example being magnesium12 which has the same crystal structure as a titanium. The spread of plasticity from grain to grain in hexagonal metals may be more difficult than in cubic metals because of the limited number of slip systems in the former, and this may account in part for their fatigue behavior. The present work was undertaken to elucidate the relative importance of crystal structure, strain aging, and initial dislocation locking in determining the properties of commercially pure titanium when subjected to cyclic stressing. 1) EXPERIMENTAL METHODS Three grades of commercial-purity titanium were used and a material of lower interstitial content was prepared by melting high-purity Japanese sponge titanium (referred to as H.P. Ti). The compositions and typical mechanical properties of the materials are shown in Table I. Fatigue tests were made in push-pull (zero mean stress) using an Amsler Vibraphore machine at a frequency of about 160 cps. Two types of fatigue specimen were used—one with a waisted gage length for determination of S-N curves and the other with a parallel gage length for metallographic studies and damping measurements. After careful machining and mechanical polishing, all specimens were electropolished prior to fatigue testing. The electrolyte consisted of 10 parts methyl alcohol, 6 parts 2-butoxyethanol, and 1 part perchloric acid (SG 1.54) and it was maintained at a temperature of -10" to -20°C during polishing. Tests at room temperature were normally carried out with the specimen immersed in a silicone oil bath which could be heated for elevated-temperature tests.

Jan 1, 1969

By Simon D. Strauss

What are future prospects for U.S. mining? In many quarters the assumption is made that this country has passed its zenith as a mineral producer -- that it is in a period of decline and that it is becoming a have-not nation like Japan and much of Western Europe. These industrial rivals of ours must depend almost entirely on others for their mineral supplies. In trying to answer this question one must of course distinguish between resources and productive capacity. In today&apos;s volatile and competitive markets, the definition of what are reserves and what are merely identified resources becomes ever more difficult. Many large deposits have been found that are unlikely to be viable in the marketplace under normal conditions but that can be of significance to the nation&apos;s military and industrial security in times of emergency. I should like to draw on personal experience from World War I1 for illustration. 4fter Pearl Harbor great concern developed over the availability of a long 1ist of strategic materials for which this country was largely dependent on imports. Included were a number of minerals of which domestic deposits had been identified. Among these were chromite, manganese ore, mercury, mica and tungsten.

Jan 1, 1982

By George W. Orton

i\- number of investigations have established that tungsten monocarbide (WC) forms throughout a wide range of temperatures (800° to 2200°C), but the di-tungsten carbide (W2C) forms only at the high end of this temperature range.1"7 In addition the decomposition of WC into WzC and C at elevated temperatures has been observed.8"10

Jan 1, 1964

By F. C. NINNIS

AT THE Belmont mill, the pregnant solution is de¬livered to a 30 by 10-ft. tank, from which it is pumped to three Merrill clarifying presses of the sluice-bar type, whence it flows through the meter to the precipitation supply tank. ?The solution for precipitation is pumped by a 10 by 10-in. Aldrich triplex pump and delivered through a 6-in. line to the forty-eight triangular frame Merrill presses at the head of the mill. Zinc dust is fed in at the pump suction and the solution precipitated to 0.01 to 0.02 oz. silver. The solution flowing from the presses is tested at 1-hr. intervals with sodium sulfide. All solution is precipitated to the same value; 4J tons of solution are precipitated for each ton of ore treated and the presses are cleaned every 15 days. The product from the presses&apos; is dumped into steel cars having steam-jacketed bottoms, in which they are dried until the moisture content is between 15 and 17 per cent. when 8. per cent. of soda and .3 per cent. of borax are added and the contents thoroughly mixed. In the case of special clean-ups, the precipitate is tested and the flux is added to meet the requirements.

Jan 1, 1921

By A. E. Worthington, R. F. Meldau

An analog computer study was made of the reduction of the magnitude of the SP by formation geometry and resistivity effects. Practical field .situations were studied. The analog data were converted to the form of departure charts. These charts may he used to determine the reduction in the SP due to the above eflects pith good precision Quantitative interpretation of the SP log in terms of formation water resistivity is presently based on the premise that the observed SP is equal to the electrochemical potential developed across a shale between the mud filtrate and the formation water. This procedure inherently assumes that, first, no electro kinetic (streaming) potential is present, and, second, that the SP is not reduced by resistivity or geometry effects in the formation. When, however, such a reduction of the observed SP does occur, one may write, SP = b,E, b, E, (1) where SP is the observed self-potential opposite the center of the bed under consideration. In this case, E, is the electrochemical potential, E, is the electrokinetic potential, b, is the electrochemical reduction factor, and h, is the electrokinetic reduction factor. The first assumption above is equivalent to assuming E, = O in Eq. 1 and the second assumption is equivalent to h, = b, = 1. Examination of electric logs shows that for many formations of interest the observed SP is reduced below its maximum value. The object of this work is to aid quantitative SP interpretation in at least some of these situations by obtaining values for b, and b, in Eq. 1 as functions of realistic combinations of bed thickness, depth of invasion, and formation resistivity. The only previously published work in this field known to the authors is by H. G. Doll&apos; in 1948. He evaluated b, under conditions permitting exact analytical solution. His work clearly established the importance and qualitative nature of formation geometry and resistivity effects upon the SP, but the necessity of obtaining analytical solutions restricted his study to situations of limited practical interest. In order to extend such studies to practical combinations of formation parameters which do not lend themselves to feasible analytical solutions, the results reported in this paper were obtained by use of a special analog computer. THE ANALOG MODEL The analog model used for this study was the Guyed Analog Computer which originally was designed and built for resistivity log departure curve studies. It consists of a two-dimensional mesh of resistors, with the vertical mesh corresponding linearly to vertical distance along the borehole, and the horizontal mesh corresponding to radial distance from the borehole axis. By proper choice of horizontal resistor values, a three-dimensional, axially symmetric, borehole-formation problem can be modeled with this two-dimensional array. These and other details of the model are contained in a paper by H. Guyod&apos;. The geometry used for the SP studies with the analog is depicted in Fig. 1. This configuration has a horizontal plane of symmetry, and, hence, the model, and the following discussion, need only to be concerned with one quadrant such as shown in Fig. 2. A further simplification arises by considering that both the natural potential sources and those used in the model have fixed internal impedance. Therefore, the current flows produced by these sources can be separated and studied independently ( i.e., the superposition theorem can be applied). SP = SP, i SP, = h,E, + b,E, ,(7)

By H. E. Criner, M. G. Driessen

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom&apos;s paper can be written: Q Q = K D&apos;. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D ,41 Elimination efficiency, in the terminology of Dahl-strom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By M. G. Driessen, H. E. Criner

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom&apos;s paper can be written: Q Q = K D&apos;. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D ,41 Elimination efficiency, in the terminology of Dahl-strom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By Magnus Troilius

The following is a very rapid method for determining copper in steel. I have found it to give results very closely agreeing with those obtained by galvanic precipitation of the copper. Five grams of steel are dissolved in a mixture of 100 C.C. of water and 10 C.C. of sulphuric acid. When all is dissolved, add 2 C.C.

Jan 1, 1883

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.&apos;-&apos; The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.&apos;, 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards&apos; law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525&apos;, 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By C. O. Worden, E. K. Landgraf, C. A. Zapffe

Following the discovery of Parke and Ham that deoxidation control of cast molybdenum can be predicated upon simple fractographic examination, a special study of that metal was undertaken to investigate those patterns ascribed to forge-ability and nonforgeability. An elaborately developed system of cleavage patterns immediately rewarded the study; and they are reported here as a necessarily preliminary contribution calling attention to information which is both new in type and in origin. In general, the present observations confirm those of Parke and Ham, and Wood-side; but they also disclose a wealth of detail and correlated phenomena which greatly expand the earlier information. For example, the oxide pattern of nonforgeability is found to be complex, perhaps involving as many as three distinctive patterns, And the nature of the carbide seems to be at least twofold. In addition, transgranular facets are here shown for the first time. Elaborately complex, but in a characteristic manner, these facets depict distortion in original crystal growth which provides truly extraordinary patterns. No carbide and oxide forms display themselves transgranularly, except in profile as exceedingly thin superficial films at the grain boundaries. Crys-tallographic features are also rare—a condition undoubtedly resulting from the great substructural distortion; but occasionally registrations are found of cleavage on {00I}, and faulted areas believed to be Neumann-type deformation on I I121. Introduction Parbe and Ham,&apos; and again Woodside,2 have reported that the forgeability of molybdenum cast by their Vacuum-electric-arc Process can be predicted with great dependability by a simple fractographic observation. They state that nonforgeability is the result of a grain boundary oxide which can be readily identified on the fracture facet at high magnification; and they convert the nonforgeable condition to a forgeable one by increasing the carbon content of the melt until the oxide structures subsequently observed in the fracto-graph become replaced by a second strongly marked pattern characteristic of carbide and coincidentally indicative of forgeability. Considerable importance immediately attaches to such observations: (I) because of their direct commercial application to one of metallurgy&apos;s inviting and relatively unexplored metals; (2) because of a general scientific curiosity regarding the nature of these characteristic markings; and (3) perhaps more important, because of

Jan 1, 1949

By Clarence Seyler

THE technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter1 published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter&apos;s method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze&apos;s solution having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and cannels, as well as with anthracite. For anthracites, I have used the chromic method and Turner&apos;s method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened&apos; with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 c.c of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 3, 1925

By Clarence A. Seyler

The technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter&apos; published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter&apos;s method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze&apos;s solution, having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and camels, as well as with anthracite. For anthracites, I have used the chromic method and Turner&apos;s method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 C.C. of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 1, 1925

By C. E. Melbye

A serious problem confronted the city of Gunnison early in 1958 in that, for a few months during each spring runoff, the water supply derived from the Gunnison River became polluted to an unsafe point. The city management had the choice of building a new filter plant to replace the old unworkable one or drilling wells to develop a ground water supply. The cost of a new filter plant was estimated at $180,000 compared to $50,000 for 6 wells, pumps, and additional water lines, hence their decision to attempt the development of sufficient ground water. Six wells at 300 gpm per well were estimated as necessary to handle the peak usage of 1800 gpm, compared to only 600 gpm winter usage. Although the water table is only about 7 feet below the surface, existing private wells drilled at random locations were producing much less than 300 gpm. The problem was to find sufficient quantities from about 6 wells. Since the presence of an ancient bedrock channel was suspected, which would be expected to localize greater quantities of water, the city of Gunnison authorized a resistivity survey to investigate bedrock topography below unconsolidated gravels. Survey results were highly satisfactory and led to the preparation of a fairly detailed bedrock contour map, Fig. 1. This map was used in selection of all well sites. The city of Gunnison is situated in a flat, broad, Quaternary gravel-filled valley (terrain dips south at 20 feet per mile) at the junction of the Gunnison River and Tomichi Creek. The valley, about 2-4 miles wide, is bordered by hills of Tertiary volcanics to the northwest, Cretaceous and Jurassic sediments to the north and northeast, and pre-Cambrian granite and gneiss to the south. One previous deep test well at the west end of the city hit pre-Cambrian granite at 496 feet, which, allowing for 40 feet of surface gravels, makes the older sedimentary section 456 feet thick. This section is probably all Jurassic Morrison formation, consisting of the Saltwash sandstone overlain by the much thicker section of Brushy Basin shales and mudstones. According to the driller&apos;s logs, each well was bottomed in what is believed to be Brushy Basin shale. FIELD PROCEDURE A standard Gish-Rooney type of resistivity apparatus was employed, which used 45-volt dry batteries as a direct-current power source. Applied voltages could be selected from 45 volts to a 270-volt maximum. Copper-coated steel stakes were employed as current electrodes and porous porcelain pots as potential electrodes to avoid possible polarization effects with direct current. The expanding Wenner electrode configuration was utilized for this investigation and measurements were made at 20 40, 60, 80, and 100-foot spacings,

Jan 1, 1961

By W. S. Ayres

I. INTRODUCTION. THIS cavern was discovered Oct. 22, 1904, by Mr. Charles H. Deutschman, in company with whom I made, May 29 to June 3, 1905, at the request of Mr. Howard Douglas, Superintendent of the Canadian National Parks, the first exploration of it for the Canadian government. The results were stated in a paper, orally presented, with lantern-views from my photographs, at the British Columbia Meeting of the Institute, Victoria,, B. C., July 5, 1905.* The present paper embodies also the results of a second examination, made Oct. 25 to 29, 1905. The accompanying map, Fig. 1, will serve as a guide to the following description. II. LOCATION. The cavern is situated at snow-line, at the head-waters of Cougar creek, on the west slopes of the Selkirks, about 2 miles north from Ross Peak water-tank, and 5.5 miles west from Glacier House, on the main line of the Canadian Pacific Railway. It was then reached by an arduous climb from the water-tank, up the ravine of Cougar creek, for 8,000 ft. (2,000 ft. of altitude) over rock- and snow-slides, and through a thick tangle of alders. But an easy and very picturesque trail has, during the past summer, been opened by the government from Glacier House. Figs. 2, 3 and 4 represent views, not heretofore published, of the grand scenery of this region, so rapidly becoming the-object of attraction to thousands of tourists from all parts of the world. These views, as well as those shown in. Figs. 5, 6, 7, 8

Jan 1, 1907

By L. C. Uren

Some of US have been impressed with the need for a better understanding of the future place of the engineer in the petroleum industry. In academic work we are continually asked to advise students as to the opportunities in different directions, to guide them in their selection of professions, and it would be extremely helpful to those in academic lines of work to have the opinion of engineers from the industry relative to the need for petroleum engineers. IS the industry going to require a continually growing number of engineers in the future years, or have we perhaps reached equilibrium in that regard ? In anticipation of this meeting, I undertook to canvass opinion among a number of engineers of my acquaintance and I have been rather astonished to learn that the expenditure on engineering salaries in the producing branch of the oil industry is extremely low. I have figures from eight or 10 of the larger oil companies and it seems to be a fair statement on the basis of these figures to say that the average American oil company is devoting less than 2 per cent. of its gross expenditures in oil production to the payment of engineering salaries. A few examples will be of interest. I shall not mention names of individual companies, but one large Mid-Continent company is spending slightly less than 1 per cent. of its gross expenditure—that is, less than 1 per cent. of the total expenditure in the producing department—on engineering salaries and about as much on engineering research, which might properly be regarded as a phase of its engineering work. Another Mid-Continent company is spending about 11/4 per cent. on engineering salaries. A large California company is spending about l1/2 per cent. The largest figure that has come to my attention is that of an important Rocky Mountain and Mid-Continent company that is spending a little more than 6 per cent., but that is apparently an extreme case. The petroleum producing industry is a highly technical business in these days. It is spending in excess of $500,000,000 annually in new

Jan 1, 1929

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

Jan 1, 1882